CENTAUR 40 Gas Turbine Generator Set

Transcription

1 CENTAUR 40 Industrial/Utility Grade Features Industrial Gas Turbine Package Compact, Integrated Package Providing Ease of Installation Factory Tested Dry, Low Emission (SoLoNOx ) Combustion Available Onskid Microprocessor-Control with Auto Sync Capability Multiple Fuel Capability Package Arrangement Gas Turbine Centaur 40 Industrial, Single-Shaft Axial Compressor 11 Stages Annular Combustion Chamber 10 Fuel Injectors Coatings Compressor: Inorganic Aluminum Turbine and Nozzle Blades: Precious Metal Diffusion Aluminide Proximity Probe Vibration Transducers Main Reduction Drive Epicyclic 1800 or 1500 rpm Acceleration Vibration Transducers Generator Salient Pole, 3 Phase, 6 Wire, Wye Connected, Synchronous with Brushless Exciter Open Drip-Proof Construction Sleeve Bearings Velocity Vibration Transducers Solid-State Voltage Regulation with Permanent Magnet Generator NEMA Class F Insulation with F Rise Continuous Duty Rating Package Steel Base Frame with Drip Pans Direct-Drive AC Start System Natural Gas Fuel System Microprocessor-Based PLC Generator Control Vibration and Temperature Monitoring Auto Synchronizing Integrated Lube Oil System Turbine-Driven Lube Pump AC Pre/Post Lube Pump Backup Lube Pump Air/Oil Cooler Integral Lube Oil Tank Lube Oil Tank Heater Lube Oil Filter Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports O&M Manuals Factory Testing of Turbine and Package Optional Equipment/Services Generator Options: WPII, TEWAC Standby Duty Rating Standard Voltages: 3300, 6600, 11, Hz; 4160, 6900, 12,470, 13, Hz Fuel Systems Liquid Dual (Gas/Liquid) SoLoNOx, Dry, Low Emission Alternate Fuels (such as naphtha, propane, low Btu) Lube Oil System Water/Oil Lube Cooler Electrostatic Demister Duplex Lube Oil Filters Remote Display/Control Terminal Heat Recovery Application Interface Serial Link Supervisory Interface KW Control KVAR/Power Factor Control Turbine Performance Map Historical Displays Printer/Logger Predictive Emissions Monitoring Field Programming Terminal Accessory Equipment 24-VDC Battery/Charger System Turbine Cleaning System: On-Crank and On-line Package Lifting Kit Weatherproof Acoustic Enclosure Ancillary Equipment: Various Air Inlet and Exhaust Systems Inlet and Exhaust Silencers Self-Cleaning or Prefilter/Barrier Air Inlet Filter Inlet Evaporative Cooler Inlet Chiller Coils Ancillary Support Frame

2 CENTAUR 40 Nominal Performance* Available Performance Output Power, kwe ISO: 15 C (59 F), sea level 3515 Heat Rate, kj/kwe-hr (Btu/kWe-hr) (12,240) Exhaust Flow, kg/hr (lb/hr) (147,718) Exhaust Temperature, C 437 ( F) (819) * No inlet or exhaust losses Relative humidity 60% Natural gas fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) OUTPUT POWER AT GENERATOR TERMINAL, MWe (61) Full Load Output 14 (48) 16 (55) 12 (41) Fuel Flow, MW (MM Btu/hr) 10 (34) 8 (27) 250 (482) 300 (572) Exhaust Temperature, C ( F) Exhaust Flow, Thousands kg/hr (lb/hr) 400 (752) 350 (662) 500 (932) 450 (842) (168) -30 (-22) 74 (163) 72 (159) -10 (14) 70 (154) 68 (150) 10 (50) 66 (146) 64 (141) 62 (137) 30 (86) 50 (122) INLET AIR TEMPERATURE, C ( F) DS40IPG-002M Typical Service Connections Forward End Turbine Control Box Length: 9754 mm (32 0 ) Width: 2438 mm (8 0 ) Height: 2591 mm (8 6 ) Approx. Weight: Forward End kg (57,350 lb) Left Side Lube Oil: Drain, Vent, Cooler Generator Control Box, Power Generator Drip Pan Drain AC Power Lube Tank Heater Pre/Post Lube Pump Backup Lube Pump Right Side Left Side AC Power - Start Motor Generator Monitor Box Aft End Aft End DS40IPG-003M Fuel Inlet Turbine Cleaning Fuel Filter, Combustor and Exhaust Collector Drains Auxiliary Air (optional) for: Liquid Fuel Atomizing Self-Cleaning Filter AC Power Liquid Fuel Pump (optional) Package Ground Solar Turbines Incorporated P.O. Box San Diego, CA Caterpillar is a trademark of Caterpillar Inc. Solar, Centaur and SoLoNOx are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS40IPG/1198/5M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Telex: Internet:

3 CENTAUR 50 Industrial/Utility Grade Features Industrial Gas Turbine Package Compact, Integrated Package Providing Ease of Installation Factory Tested Dry, Low Emission (SoLoNOx ) Combustion Available Onskid Microprocessor-Control with Auto Sync Capability Multiple Fuel Capability Package Arrangement Gas Turbine Centaur 50 Industrial, Single-Shaft Axial Compressor 11 Stages Annular Combustion Chamber 12 Fuel Injectors Coatings Compressor: Inorganic Aluminum Turbine and Nozzle Blades: Precious Metal Diffusion Aluminide Proximity Probe Vibration Transducers Main Reduction Drive Epicyclic 1800 or 1500 rpm Acceleration Vibration Transducers Generator Salient Pole, 3 Phase, 6 Wire, Wye Connected, Synchronous with Brushless Exciter Open Drip-Proof Construction Sleeve Bearings Velocity Vibration Transducers Solid-State Voltage Regulation with Permanent Magnet Generator NEMA Class F Insulation with F Rise Continuous Duty Rating Package Steel Base Frame with Drip Pans Direct-Drive AC Start System Natural Gas Fuel System Microprocessor-Based PLC Generator Control Vibration and Temperature Monitoring Auto Synchronizing Integrated Lube Oil System Turbine-Driven Lube Pump AC Pre/Post Lube Pump Backup Lube Pump Air/Oil Cooler Integral Lube Oil Tank Lube Oil Tank Heater Lube Oil Filter Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports O&M Manuals Factory Testing of Turbine and Package Optional Equipment/Services Generator Options: WPII, TEWAC Standby Duty Rating Standard Voltages: 3300, 6600, 11, Hz; 4160, 6900, 12,470, 13, Hz Fuel Systems Liquid Dual (Gas/Liquid) SoLoNOx, Dry, Low Emission Alternate Fuels (such as naphtha, propane, low Btu) Lube Oil System Water/Oil Lube Cooler Electrostatic Demister Duplex Lube Oil Filters Remote Display/Control Terminal Heat Recovery Application Interface Serial Link Supervisory Interface KW Control KVAR/Power Factor Control Turbine Performance Map Historical Displays Printer/Logger Predictive Emissions Monitoring Field Programming Terminal Accessory Equipment 24-VDC Battery/Charger System Turbine Cleaning System: On-Crank and On-line Package Lifting Kit Weatherproof Acoustic Enclosure Ancillary Equipment: Various Air Inlet and Exhaust Systems Inlet and Exhaust Silencers Self-Cleaning or Prefilter/Barrier Air Inlet Filter Inlet Evaporative Cooler Inlet Chiller Coils Ancillary Support Frame

4 CENTAUR 50 Nominal Performance* Output Power, kwe ISO: 15 C (59 F), sea level 4600 Heat Rate, kj/kwe-hr (Btu/kWe-hr) (11,628) Exhaust Flow, kg/hr (lb/hr) (151,410) Exhaust Temperature, C 509 ( F) (949) * No inlet or exhaust losses Relative humidity 60% Natural gas fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) Available Performance OUTPUT POWER AT GENERATOR TERMINAL, MWE (172) 20 (68) 18 (61) 250 (482) 200 (392) 450 (842) 400 (752) 350 (662) 300 (572) Full Load Output 16 (55) 14 (48) 12 (41) 10 (34) 8 (27) 550 (1022) Fuel Flow, MW (MM Btu/hr) Exhaust Temperature, C ( F) 74 (163) 70 (154) 66 (146) 62 (137) 500 (932) -40 (-40) -20 (-4) 0 (32) 20 (68) 40 (104) 58 (129) Exhaust Flow, Thousands kg/hr (lb/hr) INLET AIR TEMPERATURE, C ( F) DS50IPG-002M Typical Service Connections Forward End Turbine Control Box Length: 9754 mm (32 0 ) Width: 2438 mm (8 0 ) Height: 2591 mm (8 6 ) Approx. Weight: Forward End kg (60,470 lb) Left Side Lube Oil: Drain, Vent, Cooler Generator Control Box, Power Generator Drip Pan Drain AC Power Lube Tank Heater Pre/Post Lube Pump Backup Lube Pump Right Side Left Side AC Power - Start Motor Generator Monitor Box Aft End Aft End DS50IPG-003M Fuel Inlet Turbine Cleaning Fuel Filter, Combustor and Exhaust Collector Drains Auxiliary Air (optional) for: Liquid Fuel Atomizing Self-Cleaning Filter AC Power Liquid Fuel Pump (optional) Package Ground Solar Turbines Incorporated P.O. Box San Diego, CA Caterpillar is a trademark of Caterpillar Inc. Solar, Centaur and SoLoNOx are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS50IPG/1198/5M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Telex: Internet:

5 MARS 100 Gas Turbine Compressor Set General Specifications Mars 100 Gas Turbine Industrial, Two-Shaft Axial Compressor 15-Stage Variable Inlet Guide Vanes Compression Ratio: 17.4:1 Inlet Airflow: 41.3 kg/sec (91.0 lb/sec) Max. Speed: 11,168 rpm Vertically Split Case Combustion Chamber Annular-Type Conventional or Lean-Premixed, Dry, Low Emission (SoLoNO x ) 21 Fuel Injectors (Conventional) 14 Fuel Injectors (SoLoNO x ) Torch Ignitor System Gas Producer Turbine 2-Stage, Reaction Max. Speed: 11,168 rpm Power Turbine 2-Stage, Reaction Max. Speed: 9500 rpm Bearings Journal: Tilting-Pad Thrust, Active: Tilting-Pad Thrust, Inactive: Fixed Tapered Land Coatings Compressor Stators and Drum: Inorganic Aluminum Turbine and Nozzle Blades: Precious Metal Diffusion Aluminide Vibration Transducer Type Proximity Probes Key Package Features Driver Skid with Drip Pans Driven Equipment Skid Compressor Compressor Auxiliary Systems 316L Stainless Steel Piping <4" Compression-Type Tube Fittings Gauge Panel Options Fluid Gauges Digital Display Electrical System Options NEC, Class I, Group D, Div 1 or 2 CENELEC, Zone 1 Turbotronic Microprocessor Control System Freestanding Control Console Color Video Display Vibration Monitoring Control Options 24-VDC Control Battery/ Charger System 120-VDC Accessory Battery/ Charger System Gas Turbine and Package Temperature Monitoring Serial Link Supervisory Interface Turbine Performance Map Compressor Performance Map Historical Displays Printer/Logger Predictive Emissions Monitoring Process Controls Compressor Anti-Surge Control Field Programming Start Systems Pneumatic Direct Drive AC Fuel Systems Natural Gas Dual (Gas/Liquid) Integrated Lube Oil System Turbine-Driven Accessories AC Motor-Driven Accessories Oil System Options Oil Cooler Oil Heater Tank Vent Separator Flame Trap Axial Compressor Cleaning Systems On-Crank On-Crank/On-Line Portable Cleaning Tank Gearbox (if applicable) Speed Increaser Speed Decreaser Air Inlet and Exhaust System Options Enclosure and Associated Options Factory Testing of Turbine and Package Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports Operation and Maintenance Manuals

6 MARS 100 Gas Turbine Compressor Set Performance No Inlet/Exhaust Losses, Relative Humidity 60%, Natural Gas Fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) Optimum Power Turbine Speed AC-Driven Accessories Engine Efficiency: 34.0% Nominal Rating ISO At 15 C (59 F), Sea Level Output Power kw (15,000 hp) Heat Rate kj/kw-hr (7490 Btu/hp-hr) Exhaust Flow kg/hr (331,500 lb/hr) Exhaust Temp 486 C (906 F) 15 C (59 F) Turbine Rating Match. Other Turbine Rating Match Points Are Available. Available Power OUTPUT POWER PARAMETER, kw (hp) (20,115) (17,433) (14,751) 9000 (12,069) 7000 (9387) 5000 (6705) 170 (375) 160 (353) Full Load Output 150 (331) 140 (309) 40 (136) 325 (617) 130 (287) 120 (265) 110 (243) 425 (797) 35 (119) 475 (887) Fuel Flow, MW (MM Btu/hr) 375 (707) 525 (977) 30 (102) Exhaust Temperature, C ( F) Exhaust Flow, Thousands kg/hr (lb/hr) 25 (85) 20 (68) 3000 (4023) 275 (527) 100 (220) 90 (198) 80 (176) 70 (154) 15 (51) 10 (34) 1000 (1341) (-40) (-22) (-4) (14) (32) (50) (68) (86) (104) (122) INLET AIR TEMPERATURE, C ( F) DS100CS-002M Package Dimensions TURBINE AIR INLET TURBINE EXHAUST 3563 mm (11' 8-1/4") 8611 mm (29' 6") 5512 mm (18' 1") Typical Weight: kg (161,616 lb) Width: 2794 mm (9' 2") DS100CS-003M Solar Turbines Incorporated P.O. Box San Diego, CA U.S.A. Caterpillar is a trademark of Caterpillar Inc. Solar, Mars, SoLoNO x, and Turbotronic are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS100CS/699/2M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Internet:

7 SATURN 20 Industrial/Utility Grade Features Industrial Gas Turbine Package Compact, Integrated Package Providing Ease of Installation Factory Tested Multiple Fuel Capability Onskid Microprocessor-Control with Auto Sync Capability Package Arrangement Gas Turbine Saturn 20 Industrial, Single-Shaft Axial Compressor 8 Stages Annular Combustion Chamber 12 Fuel Injectors Coatings Compressor: Inorganic Aluminum Turbine and Nozzle Blades: Precious Metal Diffusion Aluminide Velocity Vibration Transducers Main Reduction Drive Epicyclic 1800 or 1500 rpm Acceleration Vibration Transducers Generator Salient Pole, 3 Phase, 6 Wire, Wye Connected, Synchronous with Brushless Exciter Open Drip-Proof Construction Sleeve Bearings Velocity Vibration Transducers Solid-State Voltage Regulation with Permanent Magnet Generator NEMA Class H Insulation with H Rise Continuous Duty Rating Package Steel Base Frame with Drip Pans Direct-Drive AC or Pneumatic Start System Natural Gas Fuel System Microprocessor-Based PLC Generator Control Vibration and Temperature Monitoring Auto Synchronizing Integrated Lube Oil System Turbine-Driven Lube Pump AC Pre/Post Lube Pump Air/Oil Cooler Integral Lube Oil Tank Lube Oil Filter Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports O&M Manuals Factory Testing of Turbine and Package Weatherproof Acoustic Enclosure Optional Equipment/Services Generator Options: Standby Duty Rating Standard Voltages: 380, 415, Hz; 240, , Hz Fuel Systems Liquid Dual (Gas/Liquid) Water Injection for NOx Control Alternate Fuels (such as naphtha, propane, low Btu) Lube Oil System Water/Oil Lube Cooler Electrostatic Demister Lube Oil Tank Heater Remote Display/Control Terminal Heat Recovery Application Interface Serial Link Supervisory Interface KW Control KVAR/Power Factor Control Accessory Equipment Turbine Cleaning System: On-Crank and On-line Package Lifting Kit Ancillary Equipment: Various Air Inlet and Exhaust Systems Inlet and Exhaust Silencers Self-Cleaning or Prefilter/Barrier Air Inlet Filter Inlet Evaporative Cooler Inlet Chiller Coils Ancillary Support Frame

8 22 (50) 21 (48) SATURN 20 Nominal Performance* Output Power, kwe ISO: 15 C (59 F), sea level 1210 Available Performance (18.8) Heat Rate, kj/kwe-hr (Btu/kWe-hr) (13,972) Exhaust Flow, kg/hr (lb/hr) (51,240) Exhaust Temperature, C 516 ( F) (960) * No inlet or exhaust losses Relative humidity 60% Natural gas fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) OUTPUT POWER AT GENERATOR TERMINAL, kwe (13.6) 3.5 (12) 3.0 (10.2) 2.5 (8.5) 5.0 (17.1) 4.5 (15.4) Exhaust Temperature, C ( F) Fuel Flow, MW (MMBtu/hr) 300 (572) Full Load Output Exhaust Flow, Thousands kg/hr (lb/hr) 350 (662) 550 (1022) 500 (932) 450 (842) 400 (752) (58) 25 (56) 250 (482) 2.0 (6.8) 24 (54) 23 (52) (-22) -10 (14) 10 (50) 30 (86) 50 (122) INLET AIR TEMPERATURE, C ( F) DS20IPG-002M Typical Package Configuration PACKAGE GAUGE PANEL ENCLOSURE VENT FAN (Inside) VENT SILENCER ENCLOSURE VENT AIR INLET PACKAGE CONTROL CONSOLE LUBE OIL COOLER TURBINE AIR INLET CLEANER ENCLOSURE VENT AIR EXHAUST TURBINE EXHAUST 2134 mm (7' 0") TURBINE AIR INLET TURBINE AIR INLET ENCLOSURE VENT AIR EXHAUST 813 mm (2' 8") LUBE OIL TANK HEATER (Inside) 5982 mm(19' 7-1/2") Weight: 8980 kg (19,800 lb) 1727 mm (5' 8") DS20IPG-003M Solar Turbines Incorporated P.O. Box San Diego, CA Caterpillar is a trademark of Caterpillar Inc. Solar and Saturn are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS20IPG/1198/5M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Telex: Internet:

9 TAURUS 60 Industrial/Utility Grade Features Industrial Gas Turbine Package Compact, Integrated Package Providing Ease of Installation Factory Tested Dry, Low Emission (SoLoNOx ) Combustion Available Onskid Microprocessor-Control with Auto Sync Capability Multiple Fuel Capability Package Arrangement Gas Turbine Taurus 60 Industrial, Single-Shaft Axial Compressor 12 Stages Annular Combustion Chamber 12 Fuel Injectors Coatings Compressor: Inorganic Aluminum Turbine and Nozzle Blades: Precious Metal Diffusion Aluminide Proximity Probe Vibration Transducers Main Reduction Drive Epicyclic 1800 or 1500 rpm Acceleration Vibration Transducers Generator Salient Pole, 3 Phase, 6 Wire, Wye Connected, Synchronous with Brushless Exciter Open Drip-Proof Construction Sleeve Bearings Velocity Vibration Transducers Solid-State Voltage Regulation with Permanent Magnet Generator NEMA Class F Insulation with F Rise Continuous Duty Rating Package Steel Base Frame with Drip Pans Direct-Drive AC Start System Natural Gas Fuel System Microprocessor-Based PLC Generator Control Vibration and Temperature Monitoring Auto Synchronizing Integrated Lube Oil System Turbine-Driven Lube Pump AC Pre/Post Lube Pump Backup Lube Pump Air/Oil Cooler Integral Lube Oil Tank Lube Oil Tank Heater Lube Oil Filter Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports O&M Manuals Factory Testing of Turbine and Package Optional Equipment/Services Generator Options: WPII, TEWAC Standby Duty Rating Standard Voltages: 3300, 6600, 11, Hz; 4160, 6900, 12,470, 13, Hz Fuel Systems Liquid Dual (Gas/Liquid) SoLoNOx, Dry, Low Emission Alternate Fuels (such as naphtha, propane, low Btu) Lube Oil System Water/Oil Lube Cooler Electrostatic Demister Duplex Lube Oil Filters Remote Display/Control Terminal Heat Recovery Application Interface Serial Link Supervisory Interface KW Control KVAR/Power Factor Control Turbine Performance Map Historical Displays Printer/Logger Predictive Emissions Monitoring Field Programming Terminal Accessory Equipment 24-VDC Battery/Charger System Turbine Cleaning System: On-Crank and On-line Package Lifting Kit Weatherproof Acoustic Enclosure Ancillary Equipment: Various Air Inlet and Exhaust Systems Inlet and Exhaust Silencers Self-Cleaning or Prefilter/Barrier Air Inlet Filter Inlet Evaporative Cooler Inlet Chiller Coils Ancillary Support Frame

10 TAURUS 60 Nominal Performance* Available Performance Output Power, kwe ISO: 15 C (59 F), sea level (72) Heat Rate, kj/kwe-hr (Btu/kWe-hr) (11,263) Exhaust Flow, kg/hr (lb/hr) (174,798) Exhaust Temperature, C 486 ( F) (906) * No inlet or exhaust losses Relative humidity 60% Natural gas fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) OUTPUT POWER AT GENERATOR TERMINAL, MWe (65) Full Load Output 17 (58) Fuel Flow, MW (MM Btu/hr) 15 (51) 13 (44) Exhaust Temperature, C ( F) 11 (38) 9 (31) 300 (572) 550 (1022) 500 (932) 450 (842) 400 (752) 350 (662) Exhaust Flow, Thousands kg/hr (lb/hr) (392) 89 (196) 86 (190) 250 (482) 83 (183) 80 (176) 7 (24) 77 (170) 74 (163) 71 (157) 68 (150) -40 (-40) -20 (-4) 0 (32) 20 (68) 40 (104) INLET AIR TEMPERATURE, C ( F) DS60IPG-002M Typical Service Connections Forward End Turbine Control Box Length: 9754 mm (32 0 ) Width: 2438 mm (8 0 ) Height: 2591 mm (8 6 ) Approx. Weight: Forward End kg (64,590 lb) Left Side Lube Oil: Drain, Vent, Cooler Generator Control Box, Power Generator Drip Pan Drain AC Power Lube Tank Heater Pre/Post Lube Pump Backup Lube Pump Right Side Left Side AC Power - Start Motor Generator Monitor Box Aft End Aft End DS60IPG-003M Fuel Inlet Turbine Cleaning Fuel Filter, Combustor and Exhaust Collector Drains Auxiliary Air (optional) for: Liquid Fuel Atomizing Self-Cleaning Filter AC Power Liquid Fuel Pump (optional) Package Ground Solar Turbines Incorporated P.O. Box San Diego, CA Caterpillar is a trademark of Caterpillar Inc. Solar, Taurus and SoLoNOx are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS60IPG(5200)/1198/5M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Telex: Internet:

11 TAURUS 60 Mobile Power Unit Mobile Power - When and Where You Need It The Taurus 60 Mobile Power Unit is the prime choice if you re looking to produce reliable, low-cost, onsite peaking power. Designed as an onsite generator system to optimize service for seasonal or cyclical loads, the Taurus 60 Mobile Generator System includes these key features: Easy to Install and Relocate Highway Transportable Modular Design for Quick Set-Up and Connection No Concrete Foundation Required Compact Footprint to Minimize Space Requirements Ideal for Rental Fleets and Utility Equipment Pools Environmentally Friendly Low Emissions State-of-the-Art SoLoNOx Dry Low NOx Combustion System No Visible Emissions Sound Attenuation Package for Quiet Operation Low Profile Design to Minimize Installed Height Easy to Permit Flexible Solution Leasing and Rental Options Available 5-MW Size for Highly Flexible Capacity Addition and Operation Fuel Flexibility, Gas or Diesel with Dual Fuel Option Complete Systems Solution Set-Up and Commissioning Site Preparation (if needed) Ancillary Support Systems (if needed) Wide Range of Product Support Programs Operational Features Dispatchable to be On Line in Six Minutes (from cold start) Range of Control System Options for Remote Operation and SCADA Integration Utility Grade Switchgear and Protective Relay Module KVAR Control for Excellent Reactive Power Capability

12 TAURUS 60 Mobile Power Unit Nominal Generator Set Performance At the core of the Mobile Power Unit is the 5.5 MW Taurus 60 industrial gas turbine, with a population of more than 1085 units in the field. The Mobile Power Unit combines the features and benefits of the proven Taurus 60 industrial gas turbine with a mobile system that is easy to relocate and connect. OUTPUT POWER, KWe OUTPUT POWER Output Power, kwe ISO: 15 C (59 F), sea level 5,500 Heat Rate, Btu/kWe-hr 11, (5) (32) (59) (86) INLET AIR TEMPERATURE, C ( F) 45 (113) Typical Dimensions TURBINE INLET AIR FILTER OIL MIST ELIMINATOR GAS FUEL FILTER EXHAUST STACK AND SILENCER GAS FUEL METER ATOMIZING AIR COMPRESSOR TURBINE INLET AIR FILTER EXHAUST STACK TRAILER UP TAURUS 60 GEN SET ACCESS PLATFORM LIQUID FUEL FILTER SKID 8' 6" 4' 0" 25' 0" OIL MIST ELIMINATOR EXHAUST SILENCER PREFABRICATED POWER CONTROL ROOM TRAILER AUXILIARY LUBE OIL TRANSFORMER UP COOLER 27' 0" 6' 10" 12' 1" GROUND RESISTOR 5' 3" 5' 1/4" 3' 6" INSTALLATION PLAN VIEW GENERATOR MODULE AUXILIARY TRANSFORMER LUBE OIL COOLER GROUND RESISTOR PREFABRICATED POWER CONTROL ROOM 13' 10" 10' 0" 8' 6" 23' 7" 14' 7/8" LIQUID FUEL FILTER SKID 8' 7" ATOMIZING AIR COMPRESSOR 5' 4-1/2" POWER CONTROL MODULE Mobile Power - When and Where You Need It For information on price, delivery and how the Taurus 60 Mobile Power Unit can meet your needs for short-term capacity and reduce your exposure to market spikes, powergen@solarturbines.com or call (858) Sited Configuration of Taurus 60 Mobile Power Unit Solar Turbines Incorporated P.O. Box MZ SP3-Q San Diego, CA U.S.A. Caterpillar is a trademark of Caterpillar Inc. Solar, Taurus and SoLoNO x are trademarks of Solar Turbines Incorporated. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS60MPU/702/4M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) powergen@solarturbines.com Internet:

13 TAURUS 70 Industrial/Utility Grade Standard Package Configurations Optional Equipment Gas Turbine Taurus 70 Industrial, Single-Shaft Axial Compressor 14-Stage Variable Inlet Guide Vanes and Stators Compression Ratio 16:1 Inlet Airflow: 26.2 kg/sec (57.7 lb/sec) Speed: 15,200 rpm Vertically Split Case Annular Combustion Chamber Conventional or Lean-Premixed, Dry, Low Emission (SoLoNO x) 12 Fuel Injectors Torch Ignitor System Proximity Probe Vibration Transducers Turbine 3-Stage, Axial Flow Speed: 15,200 rpm Main Reduction Drive Epicyclic 1500 or 1800 rpm (50 or 60 Hz) Acceleration Vibration Transducer Generator Continuous Duty Rating Salient Pole, 3 Phase, 6 Wire, Wye Connected, Synchronous with Brushless Exciter Permanent Magnet Generator Open Drip-Proof Construction Sleeve Bearings Velocity Vibration Transducers NEMA Class F Insulation with F Rise Package Steel Base Frame with Drip Pans Direct-Drive AC Start System Natural Gas Fuel System Turbotronic 4 Control System ControlLogix Processor Standard Display with Discrete Event Log, Strip Chart, Historical Trend, Maintenance Screen Gas Turbine and Generator Control Vibration and Temperature Monitoring Auto Synchronizing KW Control CGCM Module KVAR/Power Factor Control (Optional) Combination Generator Control Module with Load Share, Synchronization, Voltage Control, Reactive Power Control, Generator Protection Integrated Lube Oil System Turbine-Driven Lube Pump Pre/Post Lube Pump Backup Lube Pump Air/Oil Cooler Integral Lube Oil Tank Lube Oil Tank Heater Simplex Lube Oil Filter Oil Mist Eliminator Documentation Drawings Quality Control Data Book Inspection and Test Plan Test Reports Operation and Maintenance Manuals Turbine Cleaning System: On-Crank and On-Line Factory Testing of Turbine and Package Generator Options: Totally Enclosed Water/Air Cooled Standard Voltages: 6600, 11,000 V (50 Hz); 4160, 12,470, 13,800 V (60 Hz) Fuel Systems Liquid Dual (Gas/Liquid) Alternate Fuels (such as naphtha, propane, low Btu gas) ElectricFuel Control Lube Oil System Water/Oil Lube Oil Cooler Duplex Lube Oil Filters Vent Flame Trap Auxillary and Remote Display/ Control Terminal Heat Recovery Application Interface Serial Link Supervisory Interface Turbine Performance Map Historical Displays Printer/Logger Field Programming Terminal Accessory Equipment 120-VDC Battery/Charger System Package Lifting Kit Weatherproof Acoustic Enclosure Ancillary Equipment: Inlet and Exhaust Silencers Self-Cleaning or Prefilter/Barrier Air Inlet Filter Inlet Evaporative Cooler Inlet Chiller Coils Ancillary Support Frame

14 F1 F9 F2 F10 F3 F11 F4 F12 F5 F F6 F14 F7 F15 F8 F TAURUS 70 Nominal Performance* Available Performance Output Power, kwe 7520 ISO: 15 C (59 F), sea level (238) Exhaust Flow, Thousands kg/hr (lb/hr) Heat Rate, kj/kwe-hr (Btu/kWe-hr) (10,100) Exhaust Flow, kg/hr (lb/hr) (213,840) Exhaust Temperature, C 490 ( F) (910) * No inlet or exhaust losses Relative humidity 60% Natural gas fuel with LHV = 31.5 to 43.3 MJ/nm 3 (800 to 1100 Btu/scf) OUTPUT POWER AT GENERATOR TERMINAL, MWe (89) 24 (82) 22 (75) 20 (68) 18 (61) 16 (55) 14 (48) 12 (41) 500 (932) 104 (229) 100 (220) Full Load Output 300 (572) 450 (842) Exhaust Temperature, C ( F) Fuel Flow, MW (MM Btu/hr) 350 (662) 96 (212) 92 (203) 88 (194) 84 (185) 400 (752) 10 (34) 250 (482) 1-40 (-40) -20 (-4) 0 (32) 20 (68) 40 (104) INLET AIR TEMPERATURE, C ( F) DS70IPG-002M Typical Service Connections Forward End Left Side Aft End DS70IPG-003M Right Side Lube Oil Tank Vent Package Dimensions Length: mm (37 0 ) Width: 2932 mm (9 7-7/16 ) Height: 2743 mm (9 0 ) Approximate Weight (dry): kg (110,923 lb) Left Side Lube Oil: Cooler, Drain, Vent AC Power Starter Motor Liquid Fuel Pump Pre/Post Lube Pump Oil Tank Heater Package Ground DC Power, Backup Lube Pump Lube Oil Tank Drain Forward End Turbine Control Box Generator Drip Pan Drain Package Ground Generator Control Box Generator Terminal Box Aft End Combustor and Exhaust Diffuser Drains Fuel: Inlet, Filter, Drain, Vent Auxiliary Air (optional) for: Liquid Fuel Atomizing Self-Cleaning Filter Turbine Cleaning Turbine Drip Pan Drain Solar Turbines Incorporated P.O. Box San Diego, CA U.S.A. Caterpillar is a trademark of Caterpillar Inc. Solar, Taurus, SoLoNOx and Turbotronic are trademarks of Solar Turbines Incorporated All other trademarks are the intellectual property of their respective companies.. Specifications subject to change without notice. Printed in U.S.A Solar Turbines Incorporated. All rights reserved. DS70PG/103/1M FOR MORE INFORMATION Telephone: (+1) Telefax: (+1) Internet: