STANDALONE AVR ISP PROGRAMMER QUICK GUIDE
|
|
- Brett Conrad Tyler
- 7 years ago
- Views:
Transcription
1 SELFROG STANDALONE AVR ISP PROGRAMMER QUICK GUIDE PC Driver installation You can download the windows driver from the download link in the product page. SELFROG uses a USB virtual COM port to communicate pc applications and download firmware into SELFROG. When you complete the installation, you can check the driver installed successfully in Windows Device Manager.
2 The COM port number assigned automatically by Windows. You can change the COM port number. 1. Go to Device Manager. 2. Unfold Ports (COM&LPT) and right-click on Prolific USB-to-Serial Comm Port(COMx) and select properties. 3. Go to the Port Settings tab and click the Advanced button. 4. Change the COM Port Number and click OK. 5. If a warning message pops up and complains about COM port being used by another device, just click Yes. Changing Device ID SELFROG emulates a STK500 V2 programmer and a device CPU having no actual connection with any target board. The internal target CPU is set to ATMega8 by default. You can change the default device to your actual target CPU device in the SELFROG PC application. * The direct programming from PC to a target board via SELFROG is not supported. Any installation procedure is not needed for SELFROG PC application. Download the file, unzip to a specific directory and just run it by clicking selfrog.exe.
3 1. Select the COM port where SELFROG is designated and click "Connect" icon. If it is successful, it display the device which is set in SELFROG. 2. In order to change to the device you're using in the target board, select the AVR from the device list and click the Change Device button.
4 3. You are asked to confirm to change the device. 4. If you click OK, the device signature ID is changed and the FUSES are set to the default value. * Even if you change the device, there is no change in other memories including Flash, EEPROM, LOCKBITS and the programming sequence except signature ID and the FUSES.
5 5. Click "Load Info" button and you can get the internal information of SELFROG. Loading From the PC SELFROG uses Atmel's standard STK500 V2 protocol to communicate with PC. it is compatible with a range of tools, including Avr Studio, codevision, bascom-avr, avrdude, etc. We recommend to use Avr studio 4.19(Build730) as it supports many devices, lightweight and even works well in Windows 8 and 64bit. SELFROG's internal memories can be erased, flashed with a provided HEX file, FUSES and LOCK bits can be written and/or verified. For the detailed information please refer to the Avr Studio documentation. In this guide, we will show you the procedures to prepare for the standalone programming of the target using Avr Studio First open Programmer Connect dialog. Then select STK500 with assigned port number. After clicking Connect the programming dialog should appear. * Before run Avr Studio, be sure to disconnect SELFROG PC application first. Unless, you will get an connection failed messages.
6 2. You can check the device correct by clicking "Read Signature". 3. Program Flash and/or EEPROM in order to load to SELFROG. * Erase procedure will take 2-4 seconds.
7 4. Program the Fuse bits. 5. Program the LOCK bits.
8 6. Close the connection with Avr Studio. Open SELFROG PC application and click "Load Info", then you can get the updated SELFROG information and check the automation sequence. Programming a Target 1. Power sources for SELFROG SELFROG is very compact sized and light weight, it can be used not only for the mass production but also for the field firmware upgrade and the customer support in the remote site. There are variety of power sources available for supplying 5V DC power to SELFROG via the standard 5 pin mini USB cable. Cell phone AC wall chargers having a detachable cable connection are suitable for the table mass production. Portable emergency rechargeable or AA battery cell phone chargers are useful for the field application. We recommend the ones that can supply more than 500mA.
9 2. Cable connection Connect the programmer to the target system with 10pin or 6pin connector. Here is the connector pin layouts. 3. Target Power Options There a three power options. Open the case of SELFROG and select the target power with jumper pin on the back side of the PCB. For the targets need more than 150 ma, use a separate power source for the target system.
10 4. Programming a target Quick press the push button will start to program the target and Long press( more than 1 second) will start to program and verify the target. After quick pressing the button, the blue LED is ON and start to program the target. If the target does not respond or have any connection problem, the red LED will be blinking fast. After long pressing the button, the blue LED flashes once and turns on. Then the programmer starts to program the target. When it finish programming, the blue LED flashes once and then starts to verify the data. If the verification is failed, the red LED will be blinking slowly.
Mobius 3 Circuit Board Programming Instructions
Mobius 3 Circuit Board Programming Instructions Page 1 Mobius 3 Circuit Board Programming Instructions Introduction The Mobius 3 Power System consists of at least 4 circuit boards that need to be programmed.
More informationProgramming Device Manual Booklet AVR Prog USB v2
Programming Device Manual Booklet AVR Prog USB v2 Programming device manual booklet: AVR Prog USB v2, STK500 v2 www.and-tech.pl Page 1 Content 1. Installation...3 2. HID mode drivers installation....3
More informationAVR Prog USB v3 MK II Eco Manual
AVR Prog USB v3 MK II Eco Manual Strona 1 ATTENTION!! AVRISP mkii programmer is compatible with BASCOM and AVR DUDE environment. If you want to use this programmer with AVR Studio, you need to switch jumper
More informationBluetooth HC-06 with serial port module Easy guide
1 Bluetooth HC-06 with serial port module Easy guide This manual consists of 3 parts: PART 1. Overview of Bluetooth HC-06 module with serial port. PART 2. Installing Bluetooth HC-06 module with Bolt 18F2550
More informationKeep it Simple Timing
Keep it Simple Timing Support... 1 Introduction... 2 Turn On and Go... 3 Start Clock for Orienteering... 3 Pre Start Clock for Orienteering... 3 Real Time / Finish Clock... 3 Timer Clock... 4 Configuring
More informationCOBRA 18R2 Wired Reprogramming Instructions
COBRA 18R2 Wired Reprogramming Instructions The purpose of this document is to perform a wired reprogram of an 18R2 using the COBRA wired reprogrammer. Please note that this process requires only a wired
More informationMoving Rockwell Software Activation Keys to the VersaView 200R Industrial Computer
Page 1 of 1 01/16/03 K. Smidler Moving Rockwell Software Activation Keys to the VersaView 200R Industrial Computer Rockwell Software programs often have runtime components that require activations to utilize
More informationInstallation Instructions for 9555 USB Driver
Prior to using the data modem features of your 9555 handset; you must first install the VCOMPORT 9555 USB Driver. This driver is compatible with: Windows XP Service Pack 2, Windows 2000 Service Pack 4,
More informationUser Manual. Thermo Scientific Orion
User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation
More informationRunning the R4 Software on a USB Port
Tech Note Running the R4 Software on a USB Port Like a lot of other engine management software programs that have been around for a while, the R4 program is designed to communicate through a 9-pin serial
More informationFirmware Update Instruction Manual
Firmware Update Instruction Manual This manual explains the procedures for downloading the CX2 firmware from the Ricoh website and updating the camera s firmware. Perform the following operations to update
More informationGV- RK1352 Card Reader
GV- RK1352 Card Reader The GV-RK1352 is a card reader with keypad, designed to recognize PIN codes, identification cards or both. Featured with the Wiegand and RS-485 outputs, the unit can be connected
More informationFusion. User s Guide: Updating the Fusion s Image
Fusion User s Guide: Updating the Fusion s Image The Fusion s operating system and sound-set (called the image for short) are upgradeable and allow us to make many improvements even after the Fusion has
More informationColorfly Tablet Upgrade Guide
Colorfly Tablet Upgrade Guide (PhoenixSuit) 1. Downloading the Firmware and Upgrade Tool 1. Visit the official website http://www.colorful.cn/, choose 产 品 > 数 码 类 > 平 板 电 脑, and click the product to be
More informationEvB 5.1 v5 User s Guide
EvB 5.1 v5 User s Guide Page 1 Contents Introduction... 4 The EvB 5.1 v5 kit... 5 Power supply...6 Programmer s connector...7 USB Port... 8 RS485 Port...9 LED's...10 Pushbuttons... 11 Potentiometers and
More information[USING THE NM150 WITH ADULTICIDING] July 13, 2015
Reason Adulticiding 3.5 includes support for the New Mountain NM150 Weather Station. Adulticiding fogger log point details include temperature, wind speed, and wind direction. These can be recorded from
More informationTroubleshooting Tips Lifestyle SA-2 & SA-3 Amplifier. Troubleshooting Tips
Troubleshooting Tips Lifestyle SA-2 & SA-3 Amplifier Refer to the Lifestyle SA-2 & SA-3 Amplifier service manuals, part number 271720 for schematics, PCB layouts and parts lists. Preventative Repair Measures
More informationTP- 051 GPS RECEIVER
TP- 051 GPS RECEIVER CONTENTS 1. Overview 3 2. Features 3 3. The advantages of TP-051 GPS Receiver 4 4. The appearance and structures 4 5. Applications 5 6. Installation steps for the TP-051 GPS Receiver
More informationiloq P10S.10/20 Programming device User's Guide
iloq P10S.10/20 Programming device User's Guide CONTENTS CONTENTS... 2 GENERAL... 3 USING THE PROGRAMMING DEVICE... 5 Starting the programming device... 5 Programming of locks... 5 Programming of keys...
More informationKeychain Barcode Scanner
Keychain Barcode Scanner User Guide June 2008 2008 TABLE OF CONTENTS Quick Start... 4 Congratulations... 4 Scanner Features... 4 What s Included with Your Scanner... 5 What You Need to Get Started... 6
More informationDigital Photo Bank / Portable HDD Pan Ocean E350 User Manual
Digital Photo Bank / Portable HDD Pan Ocean E350 User Manual Installing a hard disk 1. Power off the unit. 2. Remove the bottom cover from the unit by removing four screws. 3. Insert the 2.5 HDD to the
More informationIntroducing AVR Dragon
Introducing AVR Dragon ' Front Side Back Side With the AVR Dragon, Atmel has set a new standard for low cost development tools. AVR Dragon supports all programming modes for the Atmel AVR device family.
More informationThe Quadcopter Controller
The Quadcopter Controller Table of Contents Introduction to the Quadcopter controller...2 Flight Configurations...2 Updating the Firmware...3 Mounting the Quadcopter controller in your Quadcopter...8 Quadcopter
More informationPL2303HXA/XA Windows 8 Update Driver Installation. How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems
How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems Requirements USB Device with embedded PL2303HX (Rev A) or PL2303X (Rev A) chip version Driver Installer & Build date: 1.5.0 (10/21/2011)
More informationHow to install USB driver (MICRO/I)
How to install USB driver (MICRO/I) Install on Windows XP 1. Connect the USB port on HG3G series and the USB port on PC. 2. Windows displays Found new Hardware Wizard. Select No, not this time and press
More information8-bit. Application Note. Microcontrollers. AVR282: USB Firmware Upgrade for AT90USB
AVR282: USB Firmware Upgrade for AT90USB Features Supported by Atmel FLIP program on all Microsoft O/S from Windows 98SE and later FLIP 3.2.1 or greater supports Linux Default on chip USB bootloader In-System
More informationOctober 2011 3726 07897 601 Rev. B Page 1
Upgrading Polycom SoundStation2W software to Version 1.607 and CVM to Version 1.85 Installer for Microsoft Windows Vista and Windows 7 (32 and 64 bit) Operating Systems NOTE: Two versions of upgrader are
More informationMidland BT Updater BTUpdater Program Program file (x86) ), Midland
Midland BT Updater After you downloaded the BT Updater setup application from the web site, double click on it and follow the installation procedure. The BTUpdater application is automatically installed
More informationAC-PG-USBASP USBASP AVR Programmer
AC-PG-USBASP-UG TABLE OF CONTENTS 1. OVERVIEW... 1 1.1. Introduction... 1 1.2. References... 1 1.2.1. Referenced Web Pages... 1 1.2.2. Acronyms and Abbreviations... 1 1.3. Supported Microcontrollers...
More informationSelect Correct USB Driver
Select Correct USB Driver Windows often installs updated drivers automatically, and defaults to this latest version. Not all of these drivers are compatible with our software. If you are experiencing communications
More informationCurrent Cost Data Cable User Guide. Installing and configuring the data cable
Current Cost Data Cable User Guide Installing and configuring the data cable Contents About the Data Cable... 3 Data Cable Installation Steps... 3 Post Installation Checks... 3 So the driver is installed,
More informationInstall Device Drivers and Toolkit for Windows 7
Install Device Drivers and Toolkit for Windows 7 The USB driver is required for all installations to assure that the computer communicates with the digitizer. Note: Installation instructions for Windows
More informationFREQUENTLY ASKED QUESTIONS (FAQs) 123Scan 2 Scanner Configuration Utility 19 April 2011
FREQUENTLY ASKED QUESTIONS (FAQs) 123Scan 2 Scanner Configuration Utility 19 April 2011 Table of Content Question No. Product Overview What model scanners are supported by 123Scan 2 1 What are the key
More informationSECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS. Quick Start Instructions
TM SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS Quick Start Instructions Introduction WinLoad for Windows was developed to simplify and speed up the task of programming Paradox control panels. Remote
More informationSCU-19 PC Connection Cable Driver Installation Manual
SCU-19 PC Connection Cable Driver Installation Manual Installing the SCU-19 PC Connection Cable driver software on a computer makes possible data transmission and updating the transceiver firmware. Please
More informationHealth Monitoring Demo for ice40 Ultra Wearable Development Platform User Guide. UG103 Version 1.0, September 2015
ice40 Ultra Wearable Development Platform User Guide UG103 Version 1.0, September 2015 Demo Setup Hardware Requirements ice40 Ultra Wearable Development Platform Android smart phone with Android 4.3 or
More informationWarnings: This manual is intended to guide a technicians or customers who would like to repair DBL's
DBL's Service Manual Warnings: This manual is intended to guide a technicians or customers who would like to repair DBL's devices (GoIP, SIM Bank, FXS/FXO gateways) at his/her own risk. DBL SHALL NOT be
More informationTo get times into Arena Managemnt program, from the Farm Tek Timer Console.
To get times into Arena Managemnt program, from the Farm Tek Timer Console. You will need to purchase from Farm Tek the Computer Interface Cable, and a USB to Serial adapter id your computer does not have
More informationPRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL
Rev. D PRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL 10 BORIGHT AVENUE, KENILWORTH NEW JERSEY 07033 TELEPHONE: 800-524-0273 FAX: 908-686-9317 TABLE OF CONTENTS Page
More informationQUICK START GUIDE. SG2 Client - Programming Software SG2 Series Programmable Logic Relay
QUICK START GUIDE SG2 Client - Programming Software SG2 Series Programmable Logic Relay SG2 Client Programming Software T he SG2 Client software is the program editor for the SG2 Series Programmable Logic
More informationGuide for Remote Control PDA
030.0051.01.0 Guide for Remote Control PDA For Use with Bluetooth and a PC Running Windows 7 Table of Contents A. Required Parts... 3 B. PC Software Installation... 3 C. Configure PC Software... 4 D. Testing
More informationET-BASE AVR ATmega64/128
ET-BASE AVR ATmega64/128 ET-BASE AVR ATmega64/128 which is a Board Microcontroller AVR family from ATMEL uses MCU No.ATmega64 and ATmega128 64PIN. Board ET-BASE AVR ATmega64/128 uses MCU s resources on
More informationAVR Prog User Guide. Section 3
Section 3 AVR Prog User Guide 3.1 Introduction This manual describes the usage of the AVR programming SW package called Avr- Prog. AvrProg covers all of Atmel s AVR tools with programming capabilities.
More informationPlena Voice Alarm System Firmware update
Plena Voice Alarm System Firmware update 1. Introduction It is advised to update a Bosch Plena Voice Alarm System with the latest released firmware. This Application Note describes how a firmware update
More informationPHOTO BANK BACKUP DEVICE
PHOTO BANK BACKUP DEVICE Quick Installation Guide (Version 1.0) Quick Inatallation Guide Photo Bank Backup Device Page 1 Thank you for purchasing the Photo Bank Backup Device. This Quick Installation Guide
More informationDiCE INSTALLATION INSTRUCTION
DiCE INSTALLATION INSTRUCTION Volvo Cars of North America, LLC DiCE Installation Instructions 1(18) Contents 1 INTRODUCTION 3 1.1 SUPPORT 3 1.2 UNINSTALL BUILT-IN BLUETOOTH 4 1.3 INSTALL THE LATEST VIDA
More informationHow To Upgrade A Yarvik Gotab Tablet To Android 4.0 (For Android) 4.2.2 (For Ipad) 4Th Generation (For Microsoft) 4S) 4G (For Zemmer) 4
TAB420/424/460/461/464 GOTAB XERIOS 10 TABLET ANDROID 4.0 UPGRADE INSTRUCTIONS Page 1 of 9 BEFORE YOU START: BACKUP IMPORTANT DATA! Upgrading your Yarvik tablet to Android 4.0 will erase all user settings,
More informationUSER S MANUAL TACHOTERMINAL PRO. Firmware 2.00.191
USER S MANUAL TACHOTERMINAL PRO Firmware 2.00.191 In the Box miniusb-usb cable (1.8 metres) 2GB removable memory card (in the slot) TTConfigurator (pre-installed in TERMINAL folder) Optional Accessories
More informationDUKANE Intelligent Assembly Solutions
PC Configuration Requirements: Configuration Requirements for ipc Operation The hardware and operating system of the PC must comply with a list of minimum requirements for proper operation with the ipc
More informationHow To Download From A Tachograph With A Tachoreader Combo (Tachograph)
External Devices Handling Data transfer from digital tachograph PC NET SERVICE Stocerz Sp. J. Other devices - Tutorial - Pomoc All rights reserved. No parts of this work may be reproduced in any form or
More informationOrangutan X2 Firmware Update Procedure
Introduction Orangutan X2 Firmware Update Procedure Most of the Orangutan X2 hardware is controlled by the mega168 microcontroller. Firmware updates with bug fixes or additional features can be installed
More informationUSB TO UART DRIVER INSTALLATION INSTRUCTIONS FOR EAGLE FIRMWARE VERSION 2.XXX
USB TO UART DRIVER INSTALLATION INSTRUCTIONS FOR EAGLE FIRMWARE VERSION 2.XXX All files mentioned in this document are located at the Model 599 section of the Transceiver Downloads web page on the TEN-TEC
More informationDo not connect the printer to your computer s USB port until step #10
1065 South Rogers Circle Boca Raton, FL 33487 Phone (561) 998-9600 Fax (561) 998-9609 Windows Driver Installation Guide Do not connect the printer to your computer s USB port until step #10 Please contact
More informationCenturion PLUS CPC4 Download Guide
Centurion PLUS CPC4 Download Guide using C4 File Transfer Utility. 1010537 03 01 10 Section 50 1.0 Background: 1.1 The Centurion PLUS Control system consists of a Centurion PLUS Core (CPC4 1) and Color
More informationInstalling PowerLink on Windows 7 64-bit
Instruction Manual Version 1.0, Code No. 20 751 806 1 Introduction... 3 2 Installing Virtual PC... 3 3 Configuring Windows XP Mode... 5 4 Installing Powerlink to Virtual XP... 8 5 Run PowerLink software
More informationE-LINK FOR ARM. E-Link User maunal 2011.06 1 / 46
E-Link User maunal 2011.06 1 / 46 Directory 1. E-Link ARM JTAG Introduction... 3 2. E-LINK Driver setup... 6 3. E-LINK Application... 9 3.1. KeilMDK... 9 3.2. ADS... 12 3.2.1 E-LINK on ARM11 (Tiny6410/Mini6410)...
More informationTesto FlashUpdate. Instument Software Update and Download Instructions. 1... How to Download Instrument Software and Updates from the Internet
Testo FlashUpdate Instument Software Update Contents 1.... How to Download Instrument Software and Updates from the Internet 2. How to use the Flash Program 2.1.. Instrument-Preparation before Flashing
More informationTo perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:
PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,
More informationName Description Model Number. Parameters Min. Typ. Max. Note. Vaux Voltage 9.8 V 12 V 13.2 V Auxiliary Supply Voltage
Description Supports DALI interface driver Programming Supports 0-10V Programmable Driver Programming Supports Other Controllers (TDD-ANPNx, SDD-AAPNx) Off-line programming capability Auto programming
More informationUX3600/NT/NTL/NTS Quick Start Guide This Quick Start Guide will explain how to connect and communicate with the EAW UX3600, NTL720, NTS250, KFNT, and JFNT powered speakers. Table of Contents 1. Downloading
More informationBMV-602 Data Link Manual
BMV-602 Data Link Manual 1 Contents of the kit 1 x BMV-602 data link cable. 1 x Installation CD 2 System Requirements 2.1 Hardware requirements A BMV-602 with software version 2.03 or higher. A spare RS-232
More informationNetwork/Floating License Installation Instructions
Network/Floating License Installation Instructions Installation steps: On the Windows PC that will act as License Manager (SERVER): 1. Install HASP Run-time environment, SERVER 2. Plug in the red USB hardware
More informationEVA Drivers 6.1 and TWAIN Installation Guide for EVA Classic Digital Sensors
8 Westchester Plaza, Suite 112, Elmsford, NY 10523 (914) 592-6100 Fax (914) 592-6148 www.imageworkscorporation.com EVA Drivers 6.1 and TWAIN Installation Guide for EVA Classic Digital Sensors Note: This
More informationNote that you need to install the driver once on each laptop or desktop PC you use with the LP130.
Windows XP USB Download and Installation When you plug the computer cable into the VESA connector on a computer, Windows XP automatically detects and installs USB drivers for the keyboard and composite
More informationThis Upgrade Is Only Valid For The US Cellular SCH-I500 (Mesmerize). It Is Incompatible With All Other Models. Requirements
Samsung has released a software update for the US Cellular SCH-I500 (Mesmerize) which is recommended to be installed. This software will update your Samsung SCH-I500 (Mesmerize) to Android 2.3.4 software
More informationSTK500... User Guide
STK500... User Guide Table of Contents Section 1 Introduction... 1-1 1.1 Starter Kit Features...1-1 1.2 Device Support...1-2 Section 2 Getting Started... 2-1 2.1 Unpacking the System...2-1 2.2 System
More informationHow to setup a serial Bluetooth adapter Master Guide
How to setup a serial Bluetooth adapter Master Guide Nordfield.com Our serial Bluetooth adapters part UCBT232B and UCBT232EXA can be setup and paired using a Bluetooth management software called BlueSoleil
More informationInstalling the Gerber P2C Plotter USB Driver
Installing the Gerber P2C Plotter USB Driver 1 You can install a Gerber P2C plotter using a USB connection and communicate with it using compatible design software. The following procedures describe installing
More informationFREQUENTLY ASKED QUESTIONS (FAQs) 123Scan 2 Scanner Configuration Utility
FREQUENTLY ASKED QUESTIONS (FAQs) 123Scan 2 Scanner Configuration Utility TABLE OF CONTENTS Question No. Product Overview What model scanners are supported by 123Scan 2 1 What are the key features of 123Scan
More informationStatus Monitoring. Using Drivers by Seagull to Display Printer Status Information WHITE PAPER
Status Monitoring Using Drivers by Seagull to Display Printer Status Information WHITE PAPER Contents Printer Communications 3 Drivers by Seagull 3 The Seagull Status Monitor 4 Important Benefits 4 Viewing
More informationPCS300 Universal IP Reporting Module V1.0
PCS300 Universal IP Reporting Module V1.0 Reference and Installation Manual Patents: One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111,
More informationUsing the VEX Cortex with ROBOTC
Using the VEX Cortex with ROBOTC This document is a guide for downloading and running programs on the VEX Cortex using ROBOTC for Cortex 2.3 BETA. It is broken into four sections: Prerequisites, Downloading
More informationPhaser 3635MFP Software Upgrade Process
Overview Phaser 3635MFP Software Upgrade Process The Software Upgrade feature allows the customer to upgrade the machine software as requested by a Xerox Customer Support Center Representative, without
More informationHow to read this guide
How to read this guide The following shows the symbols used in this Quick start guide with descriptions and examples. Symbol Description Example P oint Reference Caution [ ] This symbol explains information
More informationHow to connect your Victron to a computer with VE Bus Quick Configure
How to connect your Victron to a computer with VE Bus Quick Configure Before connecting your Victron to a computer the following is important: - Only identical models with VE Bus software (see sticker
More informationStart A New Project with Keil Microcontroller Development Kit Version 5 and Freescale FRDM-KL25Z
Start A New Project with Keil Microcontroller Development Kit Version 5 and Freescale FRDM-KL25Z This tutorial is intended for starting a new project to develop software with Freescale FRDM-KL25Z board
More informationCONTENTS C ONTENTS CONTENTS... 1 SAFETY INSTRUCTIONS... 2 INTRODUCTION... 2 HARDWARE APPEARANCE AND CONNECTIVITY... 4 SETUP INSTRUCTIONS...
C ONTENTS CONTENTS CONTENTS... 1 SAFETY INSTRUCTIONS... 2 INTRODUCTION... 2 HARDWARE APPEARANCE AND CONNECTIVITY... 4 SETUP INSTRUCTIONS... 5 IMPORTANT NOTES:... 19 1 S AFETY I NSTRUCTIONS SAFETY INSTRUCTIONS
More informationIntroduction About ZTE Terminal Software Online Upgrade (only for USA )
Introduction About ZTE Terminal Software Online Upgrade (only for USA ) Contents 1. What is terminal software online upgrade 2. The function of online upgrade 3. The promoted object and model 4. How to
More informationFirmware & Software update procedures Amicroe TouchTAB IV.
Firmware & Software update procedures Amicroe TouchTAB IV. Important note: The steps & procedures outlined below may be of assistance if you are experiencing difficulties with your Amicroe TouchTAB 9.7
More informationThe care and feeding of Pythons at the Redmond Zoo. (Using Micro Python and pyboard with Windows)
The care and feeding of Pythons at the Redmond Zoo. (Using Micro Python and pyboard with Windows) Introduction. Pyboard connects to Windows using a standard micro USB cable. It can operate in four different
More informationSix-servo Robot Arm. DAGU Hi-Tech Electronic Co., LTD www.arexx.com.cn. Six-servo Robot Arm
Six-servo Robot Arm 1 1, Introduction 1.1, Function Briefing Servo robot, as the name suggests, is the six servo motor-driven robot arm. Since the arm has a few joints, we can imagine, our human arm, in
More informationHOW TO TRANSFER FILES BETWEEN EEN IDL7000 PVR AND USB2 DEVICE
HOW TO TRANSFER FILES BETWEEN EEN IDL7000 PVR AND USB2 DEVICE CONTENTS CONTENTS...2 FOREWORD...3 TRANSFERRING FILES BETWEEN IDL7000M PVR AND USB2 DEVICE...4 CONNECTING AN EXTERNAL USB2 DEVICE...4 COPYING
More informationTAB08-201-3G XENTA 8c 8 3G TABLET FIRMWARE UPGRADE INSTRUCTIONS
TAB08-201-3G XENTA 8c 8 3G TABLET FIRMWARE UPGRADE INSTRUCTIONS Page 1 of 9 BEFORE YOU START: BACKUP IMPORTANT DATA! Upgrading your Yarvik tablet will erase all user settings, user installed applications
More informationUSA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS. For. Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS
USA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS For Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS SECTION 1: ADAPTER CABLE CONNECTION INSTRUCTIONS... 2 SECTION
More informationa. If necessary update the Beamage-3.0 s firmware, using the BeamageUpdater (refer to p.7);
Beamage-3.0 Installation Procedures Revision 2.0 2 QUICK START These steps must be followed in the specified order. 1. Install the PC-Beamage-3.0 software. 2. Install the Beamage-3.0 USB driver by following
More informationInstalling Global Logger USB Drivers
Installing Global Logger USB Drivers For 32-bit Windows 8, skip to the section labeled, Continue with Driver Installation. For 64-bit Windows 8, start the process here. At the time of this writing, the
More informationUser's Guide DylosLogger Software Version 1.6
User's Guide DylosLogger Software Version 1.6 The DylosLogger software allows users of Dylos Air Quality Monitors equipped with PC interface to easily record, download, and graph data. The COM port is
More informationPL-2303 (Chip Rev H, HX, X) USB to Serial Adapter Windows Driver Installer Manual
PL-2303 (Chip Rev H, HX, X) USB to Serial Adapter Windows Driver Installer Manual For Windows 98/ME/2000/XP/Vista/7 Release Version 1.3 (2/4/2010) Contents Introduction Features & Specifications System
More informationNikon Firmware Update for Coolpix 5000 Version 1.7
Nikon Firmware Update for Coolpix 5000 Version 1.7 Notes: 1. It is most important that you follow the supplied directions; failure to follow all of the steps may result in your camera being disabled. 2.
More informationQuick Reference Guide VT55 & OBDII. Customer Service 1-888-621-TPMS 1-888-621-8767. Version: QSG 2.0-24/12
Quick Reference Guide VT55 & OBDII Customer Service 1-888-621-TPMS 1-888-621-8767 Version: QSG 2.0-24/12 Table of contents Section A General Description (2 / 12). Section B Triggering a Sensor / Results
More informationSLC 5/05 Processors Firmware/Operating System ControlFLASH Upgrade
Installation Instructions SLC 5/05 Processors Firmware/Operating System ControlFLASH Upgrade Catalog Numbers 1747-DU501 Topic Page System Requirements 3 Install ControlFLASH 3 Prior to Running ControlFLASH
More informationGuide to Installing BBL Crystal MIND on Windows 7
Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP
More informationTRAVELLITE MEDIA READER
TRAVELLITE MEDIA READER Designed as a High Speed 2.0 USB device, this SD/ MMC Card Reader gives you the ability to simply remove your MMC or SD media from your phone, handheld or digital camera and insert
More informationCOPYRIGHT TOP NOTCH TABLETS LLC. 2012. HOW TO: Install the Drivers to your PC so you can Flash Firmware to your RK3066 Powered Tablet.
HOW TO: Install the Drivers to your PC so you can Flash Firmware to your RK3066 Powered Tablet. 1. Inside the RKBatchTool1.5en folder you will see a sub folder called Driver 2. Inside of that folder are
More informationPossum HC2006 SERO! Telephone. Firmware Upgrade and Software Manual firmware version 2.00+
Possum HC2006 SERO! Telephone Firmware Upgrade and Software Manual firmware version 2.00+ POSSUM LIMITED, 2009 8 FARMBROUGH CLOSE STOCKLAKE PARK INDUSTRIAL ESTATE AYLESBURY BUCKS HP20 1DQ TELEPHONE (from
More informationRALS -Remote Connect (RRC) Version 2.1 Installation and Configuration Instructions
RALS -Remote Connect (RRC) Installation and Configuration Instructions Contents Page Overview... 2 RRC v2.1 Installation Procedure..... 3 Configuring the RRC 2.1 Software.. 8 Procedure for Uninstalling
More informationJVC Monitor Calibration 2 User's Guide
JVC Monitor Calibration 2 User's Guide Table of Contents 1. What is JVC Monitor Calibration 2? 2. System Requirement 3. Installation (JVC Monitor Calibration 2) 4. Uninstall 5. Installation (EyeOne Display
More informationInstallation of USB Virtual COM. Version 1.02
Installation of USB Virtual COM Version 1.02 RELEASE NOTES Version Date Notes 1.02 May 13, 2014 Modified: Install USB Virtual COM Drivers files on CD updated 1.01 Dec. 10, 2009 Supports driver for Windows
More informationHow to install USB driver (MICRO/I)
How to install USB driver (MICRO/I) HG2G-5S 1. The HG2G-5S USB driver installation wizard will start when Automation Organizer installation is complete. Click the Next button. 2. Read the license agreement
More informationCapacitive Touch Lab. Renesas Capacitive Touch Lab R8C/36T-A Family
Renesas Capacitive Touch Lab R8C/36T-A Family Description: This lab will cover the Renesas Touch Solution for embedded capacitive touch systems. This lab will demonstrate how to setup and run a simple
More information