1 High pressure washer 2 Wheel 3 Inlet connector 4 Outlet connector 5 Handle 6 Trigger gun 7 Detergent bottle. Technical Data:

Transcription

1

2 1 High pressure washer 2 Wheel 3 Inlet connector 4 Outlet connector 5 Handle 6 Trigger gun 7 Detergent bottle Technical Data: Rated pressure Permissible pressure (max.) Inlet (max.) Rated flow Max. flow 9.0MPa 12.5MPa 0.3MPa 6.0 l/min 8.0 l/min Rated voltage V V Rated frequency 50~60Hz

3 Rated power input Degree of protection Protection class Sound power level Sound pressure level Acceleration Water temperature max. N.W 1800W IPX5 II 98 db (A) db (A) m2/s2 40C 7KGs This appliance can be used for cleaning cars, floors, rooms etc... Electrical Diagram General Safety Rules This machine has been designed for use with mild detergents and cleaning agents. The use of harsh or acidic chemicals may adversely affect the safety and function of the machine. Do not use the machine within close range of other people unless they are wearing protective clothing. High risk of explosion! Do not spray flammable liquids. High pressure cleaners should NOT be used by children or untrained personnel. Water that has flown through backflow protectors is considered to be non-potable. Remove the plug from the power outlet during cleaning, maintenance and when replacing parts. Inadequate extension cords can be dangerous. Ensure that any exhaust emissions are not in the vicinity of air intakes. Do not use the appliance without reading these instructions.

4 The electrical supply connection should be made by a qualified person and comply with IEC The electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30mA for 30ms or a device that will prove the earth circuit. Keep operation area clear of all persons. High pressure hose, fittings and couplings are important for the safety of this product. Use only hoses, fittings and couplings as recommended and/or supplied by Kogan. Do not use the appliance if the supply cord or important parts of the appliance are damaged. If an extension cord is used, the plug and socket must be of watertight construction. Improper extension cords can be dangerous! High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment or the appliance itself. Do not direct the jet towards yourself or others in order to clean clothes or foot-wear. Disconnect from the electrical power supply before carrying out any maintenance. To ensure appliance safety, use only original spare parts from Kogan. Do not leave the appliance unattended while the machine is running. Turn off the unit in the event of an accident (eg contact with detergents, rinse with an abundance of clean water) or a breakdown to avoid unsafe situations. When the appliance is moving and being installed, the appliance must be placed on a flat secure surface. Additional Safety Instructions In order to safely use the cleaner, make sure you have read and understood all of these instructions and have checked the machine prior to operation. Try using the machine on concrete or an unpainted brick wall to get accustomed to the usage. Machine, hose and plug must be checked prior to operation. Defective parts must be replaced. Do not direct the jet at power sockets, people, animals or the machine itself. Do not touch the electrical plug or any wall sockets with wet hands. Use the handle to move the machine. Do NOT drag the power cord to move the unit. When unplugging power, grasp the plug itself, not the cord. Keep the power cord in a dry location when in use. To achieve maximum operating pressure, the outlet hose should be at least 3M long. Do not use the pressure cleaner in a flammable environment. Take care against kickback when operating the trigger gun. Always use two hands to grip the gun firmly before pressing the trigger. Only press the switch once the high pressure hose is tightly fixed. Always wear protective clothing, gloves and safety goggles. Do not operate barefoot or in sandals.

5 Keep hands away from jets of water, and beware of water reflecting back off surfaces. Do not direct water onto fire or hot surfaces. Heat particles and steam can be very dangerous. Use your hand ONLY to squeeze the trigger. Do not jam trigger to the ON position. Before disconnecting the high pressure hose, turn off the machine first, then squeeze the trigger until there is no more water pressure left in the system. Do not bend, twist or fold the hose. A fluctuating or excessive high water pressure may be a signal of a defect or accumulation of calcium in the hose. If this occurs, turn the machine off immediately. Do not run the cleaner without water. This will damage it. Before starting the machine, full open the water supply tap. Be careful not to bend the hose. If the machine hose or tube freezes in the winter, do not use the machine. Before storage, the water must be drained from the machine. Always store the washer in a secure, dry location. Do not use the machine in a dirty location. Place machine on flat surface. Seawater is not suitable for use with this machine. This appliance is not intended for long-term industrial use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or cognitive capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. The function of the safety valve: when the pressure exceeds the preset value, the valve returns the excess fluid into the inlet system. The function of the pressure switch: when flow to the gun is halted, the pressure switch will activate, cutting off the power supply for protective reasons.

6 Assembly Before use, please assemble the high pressure cleaner step by step. First, connect the water feeding pipe to the suction pipe by making use of a stiffened tube, then connect the other end of the suction pipe to the machines inlet (See fig 1). Connect the pressure hose to the machine's outlet (See fig 2). The outlet is made of Al-alloy. If the hole is extremely narrow, you can use some lubrication oil. Turn the water supply on, making sure the tap is fully open. Check to ensure the whole appliance is watertight and airtight. Press the gun trigger so that the air and any pressure waste go out from the piping. Now you can start the equipment up. WARNING: Do not direct the jet against people, animals or any high voltage wiring. Always disconnect the appliance from the power supply before you change any parts. WARNING: User must wear protective clothes before working with the appliance. After use, make sure the appliance and hose are both dried. Check the supply voltage. The voltage shown on the rating plate must match the supply voltage. Use only watertight power plugs and cords, with rubber insulation enclosures. Inadequate extension cords can be dangerous. Connect the hose to the jet gun (see fig 4) Connect the nozzle to the jet gun (see fig 3). Turn the nozzle clockwise until it locks into position, so the sealing ring is not damaged. All spare parts for the jet gun are equipped with ring-nut connection. Connect the hose to the machine. Check that the seal ring is properly seated.

7 Connect to the water supply The cleaner is not suitable for connection directly to potable water mains. Connect the machine to the water supply (alternately it can be a water container). Make sure the inlet water pressure keeps between 0.01MPa and 0.3MPa. The inlet pipe should be at least 5M long. Do not use the pipe if the pipe is damaged. If you want to connect the unit to potable water mains, you must install a backflow preverter in the water pipe to prevent dirty water flowing back into the drinking system. The backflow preventer must comply with EN ANNEX AA. Overheating protection The machine has an overheating protection device. It turns the unit off automatically if it overheats, in which case you should turn off the cleaner and remove the plug from the mains supply. Once the unit has had some time to cool down, you can switch it back on again. CAUTION Some painted or treated surfaces may be susceptible to damage from high pressure cleaning. Always keep a good distance away from the surface you are cleaning. USE OF THE APPLIANCE Connect the pressure hose to the water outlet of the appliance, then connect the jet gun to the other end of the pressure hose. Connect the lance to the nozzle. Check that the filter is clean. Connect the water hose to the water inlet of the appliance. Do not bend, twist or fold the hose. Turn on the water supply at the tap and check the whole machine for any signs of water leakage. At first, air in the appliance may cause unstable pressure. Discharge the air in the machine by squeezing the trigger until nothing is coming out. Connect the plug to the power socket, then turn on the machine. Use two hands to hold the appliance steady. Squeeze the trigger and then use the high pressure cleaner. SWITCHING OFF THE UNIT Turn off the water supply at the tap. Press the trigger to reduce the pressure in the appliance. Pull out the water inlet hose, then let the machine run for a few seconds to drain the water that is still stored in the pump. Switch off the appliance and disconnect the electric plug from the socket. Detach the pressure hose. To drain residual water, life up the jet gun and squeeze the trigger.

8 USER MAINTENANCE AND REPAIR Disconnect unit from electrical supply before performing any maintenance. Turn off the water supply at the tap and press the trigger to discharge built up pressure. Lubricate the fixings periodically using lubrication oil. When the water pressure is not consistent or is too high, this is a sign of a defective hose or calcium buildup in the nozzle. In this event, turn off the machine immediately. Use the nozzle cleaner to clean the hose and the water inlet filter. Change the defective filter. Make sure that the machine is clean by cleaning the components when necessary. Ensure that you have followed the instructions regarding different parts (ie pluggable ring-nuts are used to connect the gun, hose and other parts.) The seals of the ring-nut connections must be inspected for damage. Fasten the detergent tank to the foam nozzle securely. Turn on the machine, mix a mild household cleaning agent at a proportion of 1:10 with water. Keep the appliance safe and store carefully in a secure dry place. Always store the machine out of reach of children. Avoid storing the washer in temperatures below frost point. Cut off the power if the appliance malfunctions. Problem Probable Cause Possible Solution Machine will not start working Not enough water coming out or uneven working pressure. Water leaking from the pump. Motor stops suddenly. 1. No power supply. 2. Faulty power supply. 3. Locking ring of pump too tight. 1. The filter is blocked. 2. Inlet connection is not good in the inlet pipe. 3. Valve is blocked. 4. Outlet nozzle is not smooth. 3 drops of water per minute is permissible, but if more water is leaking, this may mean the seal is worn out. 1. Pressure control has worked. 2. Unit has overheated. Contact Kogan customer support. 1. Clean the filter. 2. Check the connection, tighten the seal, check hose for clogging and ensure there is enough inlet water. 3. Clean the valve and install again. 4. Contact Kogan customer support. Contact Kogan customer support. 1. Check if outlet nozzle is blocked. 2. Turn off cleaner and allow unit to cool down for a few minutes. 3. Contact Kogan customer support.

9 Detergent Issue Troubleshooting 1. Ensure that you use diluted liquid detergents. If detergent is too thick, it may cause a blockage. 2. Do not use powder based detergents as this may cause a blockage. 3. Adjust the gun nozzle down to low pressure when using detergents. 4. Check that the nozzle mouth from the detergent bottle is not blocked. Inspection and maintenance Make sure to thoroughly clean the appliance once every three months at least, more often if necessary. Before use, make sure to always thoroughly inspect the filter and nozzle, making sure there is no clogging, cracks or damage. After use, ensure there is no residual water left in the pump and hose. If the product needs to be repaired and is still under warranty, please contact the Kogan customer support team. Before repacking for storage, appliance should be cleaned and dried.