STREAMLINE. Products for the Pure Water Cleaning Industry INSTRUCTION MANUAL

Transcription

1 STREAMLINE Products for the Pure Water Cleaning Industry INSTRUCTION MANUAL PRODUCT DENVER Honda Powered Pressure Washing Bowser. TANK SIZES 450Ltr, 600Ltr, 800Ltr WARRANTY Covered for one year from recorded date of purchase. (See back page for further details) Packed By Checked By Date / /

2 PRESSURE WASHER BOWSER OPERATING INSTRUCTIONS This manual has been compiled to give all of the necessary information to operate the DENVER range of pressure washers safely and effectively. Following these simple instructions will ensure operator safety and prolong the life of the power washer. Our policy is to improve our products continuously and we therefore reserve the right to discontinue or change specifications, models or designs without notice or obligation. This equipment has been designed and manufactured for the high pressure washing of machinery, buildings etc, using water and recommended detergent. It should not be used for washing electrical equipment, people, animals and surfaces that are easily damaged. SAFETY DENVER Pressure Washer Bowsers should only be used by fully trained, competent persons. Care should be taken when lifting and handling the pressure washers as they have uneven centres of gravity and may topple over when lifted. Operators should wear appropriate protective clothing and equipment: Waterproof boots, overalls and gloves Goggles or face protection to at least BS EN166 Ear Muffs or Ear Plugs to give protection to at least EN EN352-2 Petrol engines product fumes and toxic gasses, use only in well ventilated spaces. Refueling the fuel tank should not be done in confined spaces. Check all hoses and couplings for tightness and damage, loose connections should be tightened and damaged hoses replaced. High pressure lances kick back when the operating trigger is pulled. Ensure you have good firm footing and anticipate this reaction. Extra care should be taken when working at height, working from ladders is not recommended. Use appropriate high reach poles. The high-pressure lance can be dangerous, do not point the lance directly at other persons.

3 DESCRIPTION OF MAIN FEATURES FIG Hose Reel Detergent hose connection Detergent rate control Pressure regulator Water inlet Drive engine Tank High/low pressure nozzle Hand lance Typical transport frame Water suction hose High pressure pump Water inlet filter Pressure gauge Operating trigger and safety catch 16. High pressure hose.

4 INSTALLATION 1. Check all oil levels, top up if necessary. 2. Fill the engine oil sump with 10W 30 multigrade oil and the fuel tank with unleaded petrol. 3. Fill tank with tap water. 4. Ensure that the trigger safety catch is in the on position whilst making these connections. OPERATION 1. Turn the red on/off switch to On. 2. Turn the fuel tap to the On position. 3. If the engine is cold, turn the choke lever On and advance the throttle lever to half speed. 4. Depress the lance trigger to release water pressure before starting the engine. 5. Start engine by pulling the starter rope. 6. Once the engine is running, ease the choke to the Off position and advance the throttle lever to Max. The pressure washer should always be operated with the choke off and the throttle on Max. USING THE HIGH PRESSURE LANCE 1. Release the lance safety catch, which is located behind the trigger. 2. Point the lance downwards and towards the object being cleaned. 3. Squeeze the trigger to start the high pressure jet, proceed to wash the object. Adjust the working pressure by turning the pressure regulator know + or to suit the application (fig 1, item 4). Never direct the high pressure stream at the engine or pump as this could cause irreparable damage. 4. WARNING high pressure lances kick back when the operating trigger is pulled. Ensure that you have a good firm footing and anticipate this reaction. Release the trigger to stop the high pressure jet. WASHING USING DETERGENT 1. Attach the detergent induction pipe to the pressure washer, (fig. 1, item 2) placing the opposite filter end into the detergent container. 2. Fit the low pressure nozzle on the lance and spray the water/detergent mixture onto the object being cleaned. Leave the detergent for the period recommended by the chemical manufacturer allowing it time to work, washing off with clean water. 3. The volume of detergent used can be controlled by means of the regulator on the suction valve (see fig 2, item 3).

5 SWITCHING OFF Release trigger. Reduce the engine speed by retarding the throttle lever. Turn the red On/Off switch to Off position. Depress the high-pressure lance s trigger to release the pressure in the high pressure hose. WARNING Do not let the pump idle in by-pass for lengthy periods. If you intend to break from work for more than 5 minutes, switch the machine off. Should the machine run for longer period, the temperature of the recirculating water will increase rapidly and could risk damaging the pump seals (models with internal by-pass only). STORAGE Roll the pressure hose back onto the reel, draining water from the hose. Disconnect water feed hose, draining water from the hose. Wash out detergent hose with clean water, draining water from hose. Turn over the engine by hand to expel water from the pump. Ensure the equipment is clean and dry before storage. The equipment should be stored in a dry and frost-proof place. Ensure that the fuel tap is in the Off position. Remember - Petrol gets stale by remaining in the fuel tank for long periods. Replace the fuel after two months.

6 STREAMLINE WARRANTY The warranty on Machines and Equipment is for 1 year from RECORDED DATE OF PURCHASE. THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but not limited to HOSES, FILTERS, O-RINGS, DIAPHRAGMS, VALVES, GASKETS, CARBON BRUSHES and damage to motors and other components as a result of failure to replace normal maintenance items. THIS LIST IS NOT EXHAUSTIVE. If VARITECH receives notice of such defects during the warranty period, STREAMLINE will either, at its opinion, repair or replace components which prove to be defective. Replacement parts will only be supplied under warranty, upon the inspection and approval of the defective parts by STREAMLINE. Should it be necessary to supply replacement parts before the opportunity to inspect, these will be charged at current prices and credit will only be issued upon subsequent inspection and warranty approval by STREAMLINE. The customer is responsible for the cost of return of the defective part. If warranty is approved, STREAMLINE will pay for the cost of the repaired or replacement part. REPLACEMENT PARTS SUPPLIED UNDER WARRANTY WILL BE GUARANTEED FOR THE REMAINDER OF THE ORIGINAL PARTS WARRANTY AND NOT FROM THE INSTALLATION DATE. This warranty excludes the following conditions and circumstances which are at the discretion of STREAMLINE :WEAR AND TEAR, MISUSE, ABUSE, IMPROPER MAINTENANCE, FROST DAMAGE, THE USE OF CHEMICALS OTHER THAN THOSE SUPPLIED OR APPROVED BY STREAMLINE, IMPROPER INSTALLATION OR REPAIR, UNAUTHORISED MODIFICATION, INCIDENTAL OR CONSEQUENTIAL COSTS, LOSS OR DAMAGE, SERVICE, LABOUR OR THIRD PARTY CHARGES, THE COST OF RETURNING DEFECTIVE PARTS TO STREAMLINE. This warranty constitutes the exclusive remedy of any purchaser of a STREAMLINE unit and is in lieu of all other warranties, express or implied, including without limitation any implied warranty of merchantability or fitness for use, to the fullest extent permitted by law. In no event shall any implied warranty of merchantability or fitness for use exceed the term of the applicable warranty stated above and STREAMLINE shall have no other obligation or liability. These rights cannot be transferred to a third party. August 2015

7 WHY STREAMLINE? FLEXIBILITY STREAMLINE systems can be built according to customers exact requirements. For non-standard systems, the user s needs or specifications are listened to and turned into reality. QUALITY Whilst price is important, quality is remembered long after price is forgotten. We insist on sourcing brand name products from around the world, only of a reputable quality, and bring them together under the STREAMLINE name. All STREAMLINE products carry a full one year s warranty, according to the manufacturers standard terms and conditions of sale. SERVICE We have an in-house technical helpline able to answer most of your questions relating to the capabilities and functionalities of all STREAMLINE products. If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately attend to sending you the correct item and arrange a collection of the wrong item without any quibbles. STREAMLINE is backed by a comprehensive range with massive stocks providing you with a one stop shop for all your requirements. YOU ARE IN SAFE HANDS

8