OWNER'S MANUAL FOR MODEL "SM 12"

Transcription

1 OWNER'S MANUAL FOR MODEL "SM 12" USE AND CARE OF YOUR ELECTRIC FOOD SLICER General Slicing/Red Goat Disposers 1152 Park Avenue P.O. Box 428 Murfreesboro, Tennessee (615)

2 IMPORTANT! READ THIS MANUAL BEFORE USING YOUR NEW SLICER It is important to take a few minutes to read this booklet thoroughly before using your new slicer. This will help you obtain the full benefits of the quality convenience and safety built into this product. Keep this booklet in a handy location for future reference. ASSEMBLY: Your new slicer comes to.you fully assembled and ready for use, however even a new machine shipped directly from the factory should be thoroughly cleaned before use to insure sanitary conditions. DISASSEMBLY AND CLEANING CAUTION: BE SURE THE SLICER IS UNPLUGGED AND THE REGULATOR KNOB IS SET AT "0" BEFORE CLEANING OR HANDLING. REMOVING FOOD PUSHER 1. Set thickness regulator knob to "0" position. 2. Slide platform ( 1) to extreme forward position (fig. 1 ) 3. While holding food pusher shaft (2) turn lock knob (3) counterclockwise and remove, (fig. 2) PLATFORM REMOVAL 1. Loosen knob (4) counterclockwise about one turn. (removal of knob not necessary), (fig. 3) 2. Grasp platform and pull straight up. (fig. 3) FIG. 1 FIG. 3 FIG. 2

3 REMOVING KNIFE SHARPENER CAUTION: EXTREME CARE SHOULD BE USED WHEN REMOVING SHARPENER AS THIS WILL LEAVE A PORTION OF THE BLADE EXPOSED. 1. Grasp knife sharpener (5) by knob (fig. 4). 2. Pull straight up as far as possible. DO NOT LOOSEN KNOB FROM SHARPENER. Turn clockwise one quarter of a turn and pull sharpener up and away from sheer (fig. 5). FIG. 4 FIG. 5 REMOVAL OF KNIFE COVER 1. If platform is mounted on slicer slide it to the extreme rear position away from knife. 2. While holding cover ( 6 ) loosen and remove locking knob (7) by turning it counterclockwise (fig. 6-7). 3. Push threaded stud in and remove cover. FIG. 6 FIG. 7

4 REMOVAL OF KNIFE IMPORTANT: Extreme caution must be used when removing blade. Your SM-12 knife comes to you razor sharp and thus may cause severe injury unless proper care is exercised. 1. Knife cannot be removed unless sharpener is removed first. (See removal of blade sharpener.) 2. Remove cover as described above. 3. Using a standard screwdriver, loosen and remove three mounting screws. (fig. 8). 4. Carefully, remove knife. This "Warning" label is affixed to your unit. Do Not Remove. FIG. 8 USING YOUR NEW SLICER Your slicer motor is designed to be used on volts, 60 cycle as indicated on the nameplate. Be sure the voltage is the same before plugging into outlet. 1. Place food on platform (1) (fig. 10). 2. Set regulator knob for desired slice thickness and start slicer. (If your slicer is equipped with the regulator knob "shut-off" option, the motor can be turned "on" or "off" with the use of the regulator knob while toggle switch is in "on" position. Always turn toggle switch to "OFF" position when slicer is not in use.) FIG Using platform reciprocating handle (8) move platform (1) back and forth for every slice. NOTE: push platform far enough forward to complete the slice, then pull back until the food being cut clears the cutting edge of the knife (fig. 10). Your electric slicer is gravity fed and, therefore, it does not require use of the Food Pusher. However, use of the food pusher is important to prevent personal injury, particularly when slicing small pieces of food. As a rule ALWAYS USE FOOD PUSHER. (9) NEVER FEED FOOD BY HAND (fig. 6.). FIG. 10

5 FIG. 11 LUBRICATION AND MAINTENANCE Your new slicer will offer years of maintenance free operation with proper care and use. Your motor needs no lubrication. To insure continued smooth operation, the platform guide rod should be lubricated about every two months by applying about ten drops of lightweight oil Item (12) fig. 13. FIG. 12 CLEANING Do not immerse assembled slicer or base assembly in water. Keep spray cleaners and running water away from switch area, pully/belt cover and motor mounting/housing area. Do not use abrasive cleaners. 1. Wash base with hot soapy water and dry thoroughly. 2. Clean all remaining parts with hot soapy water and dry. 3. When cleaning sharpener be sure stone and deburrer plate is free of grease and dry thoroughly. FIG. 13

6 General Slicing / Red Goat Disposers SHARPENING THE KNIFE (SUPPLEMENT) FOR MODEL SM-12A SLICER 1. SHUT OFF and unplug slicer. 2. Turn regulator knob to Zero ("O"). 3. Clean knife with hot soapy water. (See disassembly instructions, Page 2) 4. PULL UP (DO NOT TURN) sharpener using black knob. (Fig.11). 5. Rotate sharpener clockwise ¼ turn and remove (lift straight up) from shaft. 6. Inspect sharpener stones to be: a. Free of cracks or chips; if cracked or broken replace stones. b. Clean; no grease or food. c. Both stones rotate and move back and forth freely against springs. 7. If sharpener stones need cleaning, use provided brass brush, wash in hot soapy water and dry Set sharpener back on shaft and rotate further clockwise (180 from original position) and push down until stones touch knife. (Fig.12) In this position, Cap sharpener down slightly until pink stone makes firm contact with knife at the pre-set angle. (Fig. 12) 10. Plug-in and turn on slicer, KEEPING HANDS AND FINGERS AWAY FROM KNIFE Let pink stone grind knife for approximately 5 seconds. Be sure pink stone is rotating. If not, shut off slicer, remove sharpener and lubricate stone shaft with provided oil. Push-in on deburring (blue/gray) stone knob (No. 11, Fig. 12) for 2-3 seconds to "knock-off" burr on front edge of knife. Be sure that blue/gray stone is rotating. If not, shut off slicer, remove sharpener and lubricate stone shaft with provided oil. 13. When sharpening is complete, shut off slicer while stones are in sharpening position. 14. Remove sharpener by pulling up on black knob and rotating it ¼ turn counter-clockwise. 15. ALWAYS SHUT-OFF slicer when inspecting knife cutting edge. 16. CAUTION: NEVER TOUCH rotating knife; will cause severe cuts to fingers and hands. 17. Clean off filings from knife, sharpener and slicer surfaces. 18. Replace sharpener to its storage position by: a. Hold in position as shown in Fig. 5, page 3. b. Set sharpener on to shaft and rotate counterclockwise until sharpener slides-down on shaft and into storage position.

7 SLICER MAINTENANCE: Model SM-12A CLEANING: * Unplug slicer before disassembling * Read owner's manual for "how to" disassemble for cleaning * CAUTION: DO NOT immerse assembled slicer or base assembly in water * Do not wash slicer or any component parts in dishwasher * Do not use abrasive cleaners * Do not spray water or cleaners into or near slicer base openings, switch or running light Wash all parts... base, knife, covers, cheese scraper, food platform carriage, food pusher, * including total sharpener assembly with hot soapy water NOT in dishwasher and dry thoroughly Clean off grease from sharpener stones under hot running water using supplied brass * bristle brush, dry thoroughly LUBRICATION: Add daily after thorough cleaning, supplied mineral oil Do Not use vegetable oil!! * (1) one drop to each stone shaft (near spring) and sharpener mounting shaft * (1) one drop to food pusher shaft * (1) one drop behind numbers on front thickness control knob * (2) two drops to main bottom round shaft * (1) one drop to threads on back of knife cover at center and to end of shaft KNIFE SHARPENING: Read owner s manual * Shut off slicer and clean knife * Pull up sharpener, rotate clockwise 180 degrees and then push down until pink stone touches knife. * KEEP HANDS AND FINGERS AWAY FROM KNIFE, turn on slicer * Let pink stone grind for 5 to 10 seconds * While pink stone is grinding, push in blue/gray stone hold for 2 to 3 seconds to deburr * Shut off slicer, remove sharpener & clean off filings * Clean sharpener and set back in stored position Any questions?? Or for service, parts and accessories call , FAX: , FAX: General Slicing/Red Goat Disposers 1152 Park Ave P.O. Box 428 Murfreesboro, Tennessee (615)

8 KEY REPLACEMENT PARTS LIST MODEL: SM-12A QTY NO PART NO NAME: DESCRIPTION MACH 1 09-SM-1722 BUTTON: DEBURRING STONE SM-6050 NUT: STONE MTG SM-6051 FIBER WASHER SM-1327 DEBURRING STONE (GRAY) SM-1317 SHAFT: DEBURRING STONE SM-1323 SPRING: DEBURRING STONE SM-6050 NUT: STONE MTG SM-6051 FIBER WASHER SM-1203 STONE: SHARPENING SM-1318 SHAFT: SHARPENING STONE SM-1322 SPRING: SHARPENING STONE SM-1102 WASHER: FLAT 6 MM SM-1208 KNOB: SHARPENING HSG/KNIFE COVER SM-1320 SHARPENER HOUSING 1 30-SM-1320 SHARPENER ASSY COMPLETE SM-1210 SCREW: CSK HD 6MA X SM-1211 NUT: TUBE SHAFT SM-1336 RETAINING RING: STONE SHAFT SM-1202 SHARPENER FRAME ASSY 1 (INC: 1-12, 16-18, 21 &22) SM-1204 WASHER: FLAT 4MM SM-1012 SCREW: PN HD 4MA X SM-1202 TUBE SHAFT, NUT & FRAME 1 (INC: 16, 18,21 &22) SM-1207 MTG POST ASSY: SHARPENER 1 22A 08-SM-1035 SCREW: SET 8MAX SM-1319 REGULATOR PLATE SM-1208 KNOB: SHARPENER HSG/KNIFE COVER 1 24A 09-SM-1223 ROD: KNIFE COVER SM-1216 NUT: HEX 14MA X SM-1217 WASHER: FLAT 14MM X SM-1212 KNIFE HOUSING SM-1218 SPACER: KNIFE PULLEY, 23MM 1 08-SM-1340 SPACER: KNIFE PULLEY SHAFT SM-1220 KNIFE PULLEY ASSY 1 (INC: 28, 29, BRG & SHAFT) 09-SM-1222 PULLEY SHAFT 1 * 09-SM-1219 BEARING (CALL FACTORY) SM-1221 BELT: TB (THRU S/N BD012) 1 06-SM-1370 BELT: TB2-630 (S/N BD013 FWD) SM-1224 KNIFE: 12" 1 09-SM-1307 KNIFE: 12" SS SM-1220 SCREW PN HD 5MAX SM-1299 KNIFE COVER SM-1427 THUMBSCREW: KNIFE COVER SM-1441 THUMBSCREW: KNIFE WIPER SM-1284 KNIFE WIPER SM-1514 WASHER: STAR 8MM SM-1214 SCREW: HXHD 8MAX SM-1345 BASE SM-1253 PLATFORM RAIL SM-1073 SCREW: HXHD 5MAX SM-1231 REGULATOR KNOB SM-1232 BUSHING: REGULATOR KNOB SM-1301 REGULATOR CAM: 30MM SM-1091 USE P/N 08-SM SM-1228 RATCHET PIN ASSY RUNNING LIGHT: 115V GUARD: TOGGLE SWITCH SWITCH: TOGGLE, 120V SWITCH: TOGGLE, 230V 1 49A LABEL: ON/OFF 1 49B BOOT: TOGGLE SWITCH SM-1233 BRACKET: REGULATOR SPRING SM-1333 SCREW: SKHD 6MA X SM-1234 SPRING: REGULATOR SM-1235 SCREW: PN HD 6MA X SM-1267 NUT: CAM FOLLOWER SM-1267 CAM FOLLOWER PIN SM-1237 REGULATOR SLIDE SM-1236 SLIDE BUSHING SM-1363 BRACKET: REGULATOR SLIDE SM-1063 NUT: JAM HEX 6MM 2 Effective: April 1, 1999 KEY QTY NO PART NO NAME: DESCRIPTION MACH SM-1054 SCREW: HXHD 6MA X SM-1333 SCREW: SKHD 6MA X SM-1226 WASHER: FLAT 8MM X SM-1302 WASHER: LOCK SPLIT 8MM SM-1227 SCREW: HXHD 8MAX SM-1334 BUMPER: MOTOR ADJUSTMENT SCREW SM-1515 NUT: HEX 8MA SM-1515 NUT: HEX 8MA SM-1247 SCREW: BELT TENSION ADJ SM-1246 MOTOR: 115V/60HZ (THRU S/N BD012) 1 30-SM-1371 MOTOR: 115V/60HZ; SM12A NS 1 (S/N BD013 FWD) 30-SM-1230 MOTOR: 220V/50HZ 1 09-MM-9541 BEARING: # SM-1367 WIRE: MOTOR GROUND 1 08-SM-1235 SCREW: PN HD 6MAX SM-6125 GROUND TAG 3 08-SM-6127 WASHER: STAR 5MM 3 08-SM-6126 SCREW: PN HD 5MA X SM-1364 RETAINING RING: MOTOR MTG SM-1347 BRKT, MTG: MOTOR SM-12A SM-1333 SCREW: SKHD 6MA X SM-1365 POST: MOTOR MTG SM-1245 CAPACITOR: 10MF, 450V 1 (THRU S/N BD012) 05-SM-2032 CAPACITOR: 20MF, 450V 1 (S/N BD013 FWD) SM-1224 CLAMP: CAPACITOR SM-1117 SCREW: ST PN HD 39 X SM-1506 STRAIN RELIEF GSM-756 CORDSET SM-1117 SCREW: ST PN HD 39 X SM-1240 WIRE CLAMP SM-1329 BOTTOM COVER: SM-12A SM-1463 FOOT: 45MM H W/6MA STUD SM-1359 SPIKE PLATE ASSY (INC: 84,90 & 91) SM-1289 FOODPUSHER ASSY (INC 84-91) SM-1362 SCREW: FOODPUSHER STORAGE SM-1016 NUT: JAM HEX 6MA SM-1264 SCREW: SET 10MAX SM-1265 HANDLE ASSY W/STUD SM-1360 NYLON WASHER: FOODPUSHER SM-1490 KNOB: SM W/6 MM FEMALE THREAD SM-1269 SHAFT: FOODPUSHER SM-1283 LOCK KNOB: SHAFT SM-1270 PLATFORM SM-1273 PLATFORM BRKT SM-1272 HANDLE: PLATFORM SM-1274 KNOB: PLATFORM SM-1271 SCREW: HXHD 5MAX SM-1102 WASHER: FLAT 6MM SM-1080 NUT: HEX 6MM SM-1282 SCREW: HXHD 6MA X SM-1540 ROLLER: PLATFORM SM-1102 WASHER: FLAT 6MM SM-1275 ROLLER BRKT SM-1278 SCREW: RND HD (RLR BRKT) SS SM-1226 WASHER: FLAT 8MM X SM-1514 WASHER: STAR 8MM SM-1261 SCRDW:SCKHD 8MAX SM-1260 WASHER: SHAFT SM-1252 SHAFT EXTENSION SM-1259 WASHER: RUBBER SM-1337 WASHER: PLATFORM SHAFT SM-1258 BUMPER: SPRING SHAFT SM-1254 PLATFORM SHAFT SM-1255 PLATFORM CARRIAGE SM-1251 STUD: PLATFORM BRKT 10MM X SM-1256 SCREW: HXHD 6MA X 20 NYLON SM-1257 SCREW: SET (CARRIAGE) SM-1346 WASHER: RUBBER SM-1303 SCREW: PLATFORM BRKT 1 Not Pictured. General Slicing/Red Goat Disposers 1152 Park Avenue P.O. Box 428 Murfreesboro, TN (615)

9 REPLACEMENT PARTS LIST MODEL: SM-12A General Slicing/Red Goat Disposers 1152 Park Ave P.O. Box 428 Murfreesboro, Tennessee (615)

10