Rapport mini. Multi Functional CCTV Tester

Transcription

1 Rapport mini Multi Functional CCT Tester CHG FULL Tx Rx eneo is a registered trademark of ideor E. Hartig GmbH Exclusive distribution through specialised trade channels only COM / ideor E. Hartig GmbH Carl-Zeiss-Straße Rödermark, Germany Tel. +49 (0) 6074 / Fax +49 (0) 6074 / Technical changes reserved. Copyright by ideor E. Hartig GmbH 03/

2 TABLE OF CONTENTS TABLE OF CONTENTS BEFORE USING RAPPORT mini SAFETY INFOMATION PRODUCT INTRODUCTION PRODUCT SPECIFICATION Dimension LED Indicator TIONAL SPECIFICATION Mode setup Setup USER NAME SLEEP TIME BEEP FLASH SYMBOLS ideo Tester 8 Color Bar Generator Mode 0 Digital Multimeter Measuring AC & DC oltage 4 Measuring Resistance 5 Continuity Testing 5 Controller 6 (SPEED) 8 (GO TO PRE) 9 ( PRE) DATA 3 0 MULTI TION CCT TESTER 03 MULTI TION CCT TESTER

3 안전 BEFORE 및 USING 경고 사항 RAPPORT mini General Be sure to read through the "Safety Information" section before using this Rapport mini. This basic instruction manual is for users of the Rapport mini. Starting with an outline of this Rapport mini, the manual explains its operation,how it connects to other devices, how to use the menu buttons,and how it should be operated. It is highly recommended, even for those who have handled similar devices, as well as for those using it for the first time, to read all the instructions thoroughly, especially the precautions, before using the Rapport mini. If there are any questions which arise when using the Rapport mini or the unit is damaged, please contact the supplier of your Rapport mini. Safety Information highlights and explains the precautions which should be taken, for the safety of users, when using the Rapport mini. Rapport mini Safety Precautions When using the Digital MultiMeter function to measure voltage or current, be sure that the input does not exceed the capabilities of the tester. Overloading the tester can cause damage or personal injury. When measuring current of unknown values, always begin with the 0A mode, then step down to the 400mA input if necessary. Environmental Limitations Temperature: -0 to 40 degrees C Relative Humidity: 30% -90% DC input voltage: +/-0%, A Precautions SAFETY INFORMATION Pay attention to the following precautions when using the Rapport mini. -Use only specified replacement fuses. -Do not use damaged test leads with the DMM. -When using the DMM function, set the proper mode before connecting to the circuit under est. -When measuring resistance, make certain that the circuit is de-energized before connecting the test leads to the circuit. -Do not measure resistance on powered circuits. -Do not use the unit in damp, humid or gaseous environments. -Do not touch it with wet hands. -Be mindful not to shock or shake the unit while in use to avoid damage. -Avoid areas with strong magnetic or electromotive fields, which can cause incorrect measurements. -Remove the power plug from the outlet when there is a lighting storm. -Neglecting to do so may cause fire or damage to the product. -The Main plug is used as a disconnect device and shall stay readily operable at any time. -Be sure to use only the standard adapter that is specified in the specification sheet. -Using any other adapter could cause fire, electrical shock, or damage to the product. -Securely plug the power cord into the power receptacle. Insecure connection may cause fire. -If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. -When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock 04 MULTI TION CCT TESTER 05 MULTI TION CCT TESTER

4 CHG FULL Tx Rx PRODUCT INTRODUCTION PRODUCT INTRODUCTION CHG FULL COM / Tx Rx Rapport mini has a built-in Lithium Polymer Battery. It can be recharged using a DC power adapter with an output of A or above and reaches its full charge after a period in excess of 5 hours. After the battery has been fully charged for the first 3 charging cycles, it can be used for approximately 6 hours (up to a Max.8 hrs in normal operation).the battery can be recharged by connecting it to the DC adapter, regardless of power, when the slider switch has been turned on. The discharge operation starts when the Main Switch is turned on and it then consumes power from the battery. Therefore, when the Rapport mini is not being used for a period of time, make sure the Main Switch is turned off. Summary Designed, with portability and serious CCT engineers in mind, the Rapport mini is an advanced piece of video test equipment consisting of many useful test functions needed to professionally install a CCT system; test functions include ideo Level, Service Monitor, Multimeter, Test, RS-4 and RS-485 Communication Test, etc. Standard Items Check the contents of your Rapport mini package against the standard checklist below : Rapport mini COM / Power Adaptor Test lead Accessories body cover BNC cable RAPPORT MINI MANUAL manual RAPPOR MINI MANUAL Rapport mini Package Test Leads BNC to BNC Cable Adaptor 06 MULTI TION CCT TESTER 07 MULTI TION CCT TESTER

5 PRODUCT INTRODUCTION PRODUCT INTRODUCTION Product Introduction 3 4 Part Name Function mode Adjusts Focus Near Operation IRIS Close CHG FULL Tx Rx mode Adjusts Focus Zoom-in Operation Clear of mode 5 mode Adjusts Focus Zoom-out Operation 6 mode Moves Up/Down/Left/Right & Select Menu Flash control Control flash ON/ OFF button COM / 7 Test Lead Connection : Ports for Digital MultiMeter Part Name Function CHG LED Charge LED Data Transmitting LED Data Receiving LED LCD Keypad Button Button mode Red LED is on when the system is switched on. Green LED is on when the battery is fully charghed. Red LED is on when data is transmitted. Green LED is on when data is received..5 Color TFT LCD Main keypad for Rapport mini operation Mode Select: ideo, MultiMeter, Control. Used to confirm selection in menu screens. (Press for seconds to power on.) Adjusts Focus Far Operation. IRIS COM / COM / : Common Port, Lead for black color : oltage & Resistance Port, Lead for red color 08 MULTI TION CCT TESTER 09 MULTI TION CCT TESTER

6 PRODUCT INTRODUCTION PRODUCT INTRODUCTION CAUTION Do not shine the light to the human eyes and animals. It can lead to blindness. Flash : White LED to lignt up in the dark area Internal Battery Cover DC Power Jack : DC Power Input Jack (DC, A) Power Switch : Main Power Supply ON/OFF switch Communication Port : Input & Output of communications signals (RS 4/ RS485, Rx+, Rx-, Tx+, Tx- ) ideo Port : Select ideo In and ideo out in the ideo mode in : Display input video signal to or PAL format. out : Transmit Standard Color-bar to external motor with or PAL format. 0 MULTI TION CCT TESTER MULTI TION CCT TESTER

7 PRODUCT SPECIFICATION PRODUCT SPECIFICATION Electrical Specifications Multi-meter Specifications Input oltage DC ± 0%, A Electrical Characteristic Battery Built-in charger Display 7.4 (3.7x)Li-Poly, 000mAh Charging Time : 6 hour Operation Time : 8 hour 5 hour (Light HIGH ON), Continuous working.5" TFT-LCD (Digital), RGB666 Mode DC oltage Range 400m 4 Minimum Measuring 00u m Accuracy ±(.5% +4dgts) Display Resolution Working Temp. Dimension 30 x L9.3 x W79. x T3. (mm) m 00m ±(.5% +4dgts) Functional Specifications ideo IN / OUT LCD Adjustment ideo Mode Color bar generation CH, BNC ( IN/OUT selectable),.0 pp Brightness, contrast Standard Color bar(/pal) AC oltage m 0m 00m ±(.5% +4dgts) (40Hz 500Hz) Controller Signal Mode Communication Protocol Baud rate Rx Data Analyzer DC oltage Range /PAL (Auto adapt) RS4, RS485 Multi (4 protocols) 400bps38400bps Hex alue Analysis 400m/4/40/300 Resistance 400Ω 0.Ω 4kΩ Ω 40kΩ 0Ω 400kΩ 00Ω ±(.0% +4dgts) ±(.0% +dgts) Digital Multi-Meter AC oltage Range Continuity Resistance Range 4/ 40/300 Built-in Buzzer sound 400Ω/4KΩ/40KΩ /400KΩ/4MΩ/40MΩ 4kΩ 40kΩ kω 0kΩ ±(.0% +4dgts) ±(3.0% +5dgts) Flash Control ON / OFF -iewing angle : about 60 -Normal Operation : 5 hours continuous working Continuity Beeper is activated when the resistance is below 80Ω -Flash intensity :LOW/ MID/ High Note: Maximum voltage drop approx. on the measuring current. MULTI TION CCT TESTER 3 MULTI TION CCT TESTER

8 PRODUCT SPECIFICATION PRODUCT SPECIFICATION Dimension 79. LED Indicator 3. CHG FULL Tx Rx 66.5 Item RED LED GREEN LED CHG FULL Tx Rx Discharged Charging Fully charged Low battery OFF ON OFF Flicker( Hz) OFF OFF ON OFF 63.8 Shift power switch off to Power on The LED turns Red or Green depend on the recharging status. On charging : RED LED ON Fully charged: GREEN LED ON 9.3 Battery is consumable item with 6 months warranty after purchase. Use the manufacture provided adaptor only (DC/A). When Red LED flicker, reload battery or recharge battery. After Operating with Power on - On charging: RED LED ON - Fully charged: GREEN LED ON * When it charge during operating, the screen show(page9, 3) like ( : DC Adaptor connect and Charge, : Operated by Battery) COM / * L9.3 x W79. x T3. (mm) 4 MULTI TION CCT TESTER MULTI TION CCT TESTER

9 TIONAL 제품소개 SPECIFICATION TIONAL SPECIFICATION Functional use Power ON/OFF The power switch is located on the side of the handset. Turn the power switch on, and press to start Rapport mini. To turn off the system, press & hold for more than sec. Then, POWER OFF is displayed on the main screen with a beep. Release the button. Turn the power switch OFF to prevent battery drain during storage. The switch must remain ON to recharge the batteries. A rechargeable battery should be plugged in over 5 hours to fully charge. The charged battery can operate for about 8 hours. When the battery indicator shows below, recharge it for use. (Full charge: ) Main Functions ideo Tester (Color CCT Field Monitor ) Color Bar Generator (Standard ideo Signal generator) Digital Multi-meter Controller Receive Data Analyzer Setup Flash ON / OFF Mode setup The menu changes whenever the key is pressed, and sequences through in the following order : -> ColorBar -> Meter -> controller -> Receive Data -> UP -> The SELECT menu is displayed when the key is depressed and moves to the next menu whenever the key is pressed BRI 3 CON 7 CHG Tx CHG Tx FULL Rx FULL Rx COLOR METER DATA UP RAPPORT-MINI er : 0.03 [ Mode change ] After the power is applied the above on-screen message is displayed. Approximately seconds later the screen switches to the last before power was turned off. The Rapport mini stores the last accessed. The initial message displays the Rapport mini's firmware information. ersions of the product change whenever new firmware is uploaded. 6 MULTI TION CCT TESTER 7 MULTI TION CCT TESTER

10 TIONAL 제품소개 SPECIFICATION ideo Tester Connect the output terminal of video output system to the video BNC port of Rapport mini. 4 TIONAL SPECIFICATION If there is no video signal at the IN port of the Rapport mini LOSS will be displayed. BRI 3 CON CLR 7 [ ideo Mode ] IN BRI 3 CON 7 : Indicates Current Mode. : Indicates or PAL System. (LOSS: No video) 3 Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) 4 Indicates screen brightness, and brightness increases by + when the key is pressed, and decreases by - when the key is pressed. 5 Indicates screen contrast, and contrast increases by + when the key is pressed, and decreases by - when the key is pressed. 6 Indicates Mode, and changable by button. 7 Indicates & Indicates clear button COLOR METER DATA UP [ ideo Tester mode ] [ clear] 8 MULTI TION CCT TESTER 9 MULTI TION CCT TESTER

11 TIONAL 제품소개 SPECIFICATION Color Bar Generator Mode Outputs color bars allow technicians to configure monitors and troubleshot cameras by sending a known good video signal down a questionable coax run. Supports both PAL & video signal formats. TIONAL SPECIFICATION To enter the PATTERN GENERATION press the key while in the Color bar mode. By default the ideo will be displayed in the top portion of the screen. C A U T I O N ideo teminal is selected by internal firmware. Do not go into the Color bar mode when the camera video is connected. 4 COLOR BAR BRI 3 CON OUT 6 FORMAT 7 [ Color Bar Test mode ] BRI 3 CON 7 COLOR METER DATA UP : Indicates Current Mode. : Indicates or PAL System. (LOSS: No video) 3 Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) 4 Indicates screen brightness, and brightness increases by + when the key is pressed, and decreases by - when the key is pressed. 5 Indicates screen contrast, and contrast increases by + when the key is pressed, and decreases by - when the key is pressed. 6 Indicates Mode, and changable by button. 7 Indicates video format change ( <-> PAL) COLOR BAR BRI 3 CON 7 COLOR BAR PAL BRI 3 CON 7 FORMAT FORMAT [ ] [ PAL ] 0 MULTI TION CCT TESTER MULTI TION CCT TESTER

12 COLOR METER DATA UP TIONAL 제품소개 SPECIFICATION TIONAL SPECIFICATION Digital Multimeter oltage, resistance and continuity can be tested. METER DC AC Ω OLT 3 W A R N I N G To prevent electric shocks, injury, or damage to the Rapport mini, disconnect the power supply to the circuit under test, and discharge all high-voltage capacitors before testing resistance and continuity. When using the meter function of the Rapport mini, make sure the unit is switched on and set to the appropriate test mode before connecting the test lead set to the circuit under test DC+. DC+.0 STORE 5 9 Sleep time is not operated in Multimeter mode. (Sleep function -> see 34 page) Setup Keys Press the METER DC AC METER Ω OLT AC 0.04 button to go into the multi meter mode. METER DC AC Ω OLT DC+ 00.m METER : Indicates current mode. Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) Indicates type of test set up :Resistance test, Continuity test, DC & AC oltage. Indicates test mode : DC > DC oltage, AC > AC oltage, OHM> Resistance BUZZ> Continuity Indicates test value displayed : Resistance (Ω, kω, MΩ), voltage(, m), continuity(buzz) Indicates measured graph value : The Measured Input value is displayed in the form of a graph. The graph is changed automatically and is equal to the measured value. OER is displayed when the measured value is higher than the setup value. Indicates measured value on hold : The measure value is stored and displayed here when the key is pressed. Indicates mode display : Digital multimeter mode is displayed. Indicates Store button by using button. [ Select Multi Meter Mode ] [ Multi Meter Mode ] STORE Button for Multimeter mode oltage mode OHM(resistance) mode 3 AC/DC, resistance/ continuity 3 MULTI TION CCT TESTER 3 MULTI TION CCT TESTER

13 TIONAL 제품소개 SPECIFICATION Measuring AC & DC oltage oltage is the difference in electrical potential between two points. The polarity of an AC voltage varies with time, while DC polarity is constant. The meter displays AC voltage as RMS values (Root Mean Square readings). The RMS value is the equivalent DC voltage measured in a time varying sinusoidal signal. Measuring Resistance COM / TIONAL SPECIFICATION The unit of resistance is the Ω. The meter sends a low current into the circuit so that the resistance can be measured. This current runs along all paths between the two probes and enables the total resistance to be calculated. METER DC AC Ω OLT OHM 9.86M COM / COM / OHM 9.86M STORE (AC oltage Test) (DC oltage Test) Continuity Testing Continuity means the presence of a complete path for current to flow. The continuity test features a beep that sounds when a circuit is complete. The beep allows users to quickly test continuity without having to watch the display. The beeper is activated when the resistance between the red and black probes is less than 80Ω METER DC AC Ω OLT METER DC AC Ω OLT COM / COM / AC 6.00 DC+. (AC oltage Test) STORE DC+.0 (DC oltage Test) STORE METER DC AC Ω OLT BUZZ 53.0 STORE 4 MULTI TION CCT TESTER 5 MULTI TION CCT TESTER

14 TIONAL SPECIFICATION TIONAL SPECIFICATION Controller Connecting Camera and Monitor Operation Test: Up, Down, Left, Right, Zoom and Manual focus control are possible. The tester can also be set to various protocols and transmission speeds (baud rates). 4 5 ADDR : PROTOCOL : ()PELCO-D 3 Tx+ Tx- Tx+ Rx- Rx+ Tx- control Button 6 UP 7 IN : Indicates Current Mode. : Indicates or PAL System. (LOSS: No video) 3 Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) 4 Indicates Setting -> ADDR : address setting ( 00055) -> PROTOCOL: protocol setting (4 Protocols) -> BAUDRATE : Communication speed setting (.4Kbps, 4.8Kbps, 9.6Kbps, 9.Kbps, 38.4Kbps) -> PARITY: Parity bit setting (EEN,ODD, NONE) ADDR : PROTOCOL : ()PELCO-D ADDR : PROTOCOL : ()PELCO-D The SELECT menu is displayed when the key is pressed. ADDR : PROTOCOL : ()PELCO-D ADDR : PROTOCOL : ()PELCO-D ADDR Setting OK PROTOCOL Setting ADDR : PROTOCOL : ()PELCO-D ADDR : PROTOCOL : ()PELCO-D OK COLOR METER DATA UP UP [ Select Control mode] [ Control mode ] OK OK BAUDRATE Setting PARITY Setting 6 MULTI TION CCT TESTER 7 MULTI TION CCT TESTER

15 TIONAL SPECIFICATION TIONAL SPECIFICATION - Control Setup Screen Press and hold the button for seconds until protocol menu activates. PT control (Up, Down, Left, Right), is performed using the arrow keys. c Each menu setting / value setting a a Go into the mode & Exit button b Change setting value (GO TO PRE) : Moves the camera view to a designated preset location; Presets are numbered 000 to 55. The cursor moves to the position when the key is pressed. Select the previously stored PRE number using the & keys (move by+, - step). Once selection is complete, press the key once more and the camera will move to the PRE location. ADDR : PROTOCOL : ()PELCO-D GO b c b c Select setting How to Control a Camera functions - Up, Down, Left, Right movements are carried out using the Button. Focus and Zoom adjustments are made using the / (Focus) and / (Zoom) buttons. ( PRE) : Sets and stores PRE information in the range from 000 to 55. First, move the camera to the required view and press the key, and use the & keys to place the cursor at the location of the chosen preset. Then set up the address where the preset is to be stored by using the & keys, and press the key once more. The location information is now stored as a preset address. ADDR : PROTOCOL : ()PELCO-D GO (SPEED) : Move the cursor to the icon, using the procedures described above. A total of 6 increments in speed (0 to ) are available for selection using the keys. ADDR : PROTOCOL : ()PELCO-D GO (Function): User can set different functions that automatically load the presets of the camera system. The setup uses the and information buttons for the user to program various presets. The different number of presets can range from 00 all the way to 63. The functions (presets) can be programmed by the (+), (-) buttons and steps by using the & keys. ADDR : PROTOCOL : ()PELCO-D GO 8 MULTI TION CCT TESTER 9 MULTI TION CCT TESTER

16 TIONAL SPECIFICATION TIONAL SPECIFICATION : Activates the camera s internal menu. cameras have an on-screen menu system that allows Rapport mini to program various functions of the camera including day/night mode, focus settings, and tours. When a tour is programmed into the camera it can be activated with Rapport mini using the TOUR function in the menu. ADDR : PROTOCOL : ()PELCO-D DATA : When you want to know the input signal of an exterior controller, you can see the input data(hex value) by connecting the communications cable to the RX terminal of the Rapport mini. The control commands from the keyboard of an external control are displayed on the screen. Most important is that the communications speed be matched. MAIN DOME CAMERA MOTION DISPLAY CLEAR DATA EXIT Tx- Tx+ Rx- Rx+ TX+ TX- GO UP :Change the menu. UP :Setup the Camera menu. Clear : When you press activated and press the IN button in the mode, the clear button is button, the is cleard. clear DATA RC ADDR : PROTOCOL : ()PELCO-D RX+ RX- SHIFT UP COLOR 30 SHIFT MULTI TION CCT TESTER UP 3 MULTI TION CCT TESTER METER DATA UP

17 TIONAL SPECIFICATION TIONAL SPECIFICATION DATA RC Setup 3 FF FF FF B 3B 79 FF B 3B 79 FF FF FF UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH 4 CLEAR 5 COLOR METER DATA UP DATA RC : Indicates Current Mode. Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) 3 Indicates received data. 4 Indicates change mode. 5 Indicates data clear on the screen. (Press button to operate it) DATA RC DATA RC [ Select UP mode ] [ UP mode ] Mode Select : To access this menu depress the UP icon. key and select the Select a menu item by pressing the & keys. Each setup value can be changed by pressing the & keys FF FF FF B 3B 79 FF B 3B 79 FF FF FF UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH CLEAR CLEAR [ Clear received data ] 4 UP : Indicates Current Mode. Indicates remained battery. ( : DC Adaptor connected : Operated by Battery) 3 Indicates setup items. 4 Indicates change mode. 3 MULTI TION CCT TESTER 33 MULTI TION CCT TESTER

18 TIONAL SPECIFICATION TIONAL SPECIFICATION Selecting the USER NAME initiates an editing menu and shows the associated key strokes. Select a menu item by pressing the & keys. Each setup value can be changed by pressing the & keys FLASH ON/OFF & Level Change Select a menu item by pressing the & keys. Flash level can be changed by pressing the & keys UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH UP USER NAME RAPPORT - MINI ()ABCDEFGHIJKLM NOPQRSTUWXYZ!@#$% & +-+<> UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH Flash Level - OFF - LOW - MID - HIGH BACK UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH UP USER NAME : RAPPORT - MINI SLEEP TIME : 30Min BEEP : ON FLASH LL : HIGH SLEEP TIME: Select sleep time by using the & buttons and change sleep options by using the & buttons. The options are OFF,, 5, 0, 30, 60 minutes. Sleep time makes the power go OFF automatically, unless the button is pressed. BUZZER: Select a menu item by pressing the & keys. Each setup value can be changed by pressing the & keys (ON/OFF) Flash fucntion is not worked in UP mode but only Flash level setting is available. To turn on or turn off, use the Press seconds FLASH ON button for seconds. Press seconds FLASH OFF 34 MULTI TION CCT TESTER 35 MULTI TION CCT TESTER

19 TABLE - SYMBOLS MEMO SYMBOLS Number Symbol Reference Description IRE Direct current IRE Alternating current 3 IRE Both direct and alternating current 4 3 Three-phase alternating current 5 IRE Earth (ground) TERMINAL 6 IRE PROTECTIE CONDUCTOR TERMINAL 7 IRE Frame or chassis TERMINAL 8 IRE Equipotentiality 9 IRE On(Supply) 0 IRE Off(Supply) IRE Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION Caution, rick of electronic shock 3 IRE Caution, hot surface **The equipment shall not be used for measurements of categories II, III and I. **If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. 36 MULTI TION CCT TESTER

20