TABLE OF CONTENTS 1 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...

Transcription

1 SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNDERSTANDING YOUR INSTRUMENT PANEL STARTING AND OPERATING WHAT TO DO IN EMERGENCIES MAINTAINING YOUR VEHICLE MAINTENANCE SCHEDULES IF YOU NEED CONSUMER ASSISTANCE INDEX

2

3 INTRODUCTION 1 CONTENTS Introduction... 4 A Message From DaimlerChrysler Corporation... 5 How To Use This Manual... 5 Warnings And Cautions... 5 Van Conversions/Campers... 6 Vehicle Identification Number... 6 Vehicle Modifications / Alterations... 7

4 4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar parts, and is interested in your satisfaction. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

5 INTRODUCTION 5 A MESSAGE FROM DAIMLERCHRYSLER CORPORATION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins Turbo Dieselpowered truck owner. Almost 100% of the heavy duty trucks in the United States are diesel powered because of the fuel economy, rugged durability, and high torque which permits pulling heavy loads. Cummins engines power well over half of these trucks. Now this same technology and proven performance is yours in your new Dodge Ram truck equipped with the Cummins 5.9 liter, Turbocharged, Charge Air Cooled, Diesel engine. Your diesel truck will sound, feel, drive, and operate differently from a gasoline-powered truck. It is important that you read and understand this manual. You may find that some of the starting, operating, and maintenance procedures are different. However, they are simple to follow and careful adherence to them will ensure that you take full advantage of the features of this engine. Thank you for choosing the Dodge Ram truck with Cummins Turbo Diesel power. HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. 1

6 6 INTRODUCTION VAN CONVERSIONS/CAMPERS The Manufacturer s Warranty does not apply to body modifications or special equipment installed by van conversion/camper manufacturers/ body builders. See the Warranty information book, Section 2.1.C. Such equipment includes video monitors, VCRs, heaters, stoves, refrigerators, etc. For warranty coverage and service on these items, contact the applicable manufacturer. Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your selling dealer for assistance in obtaining replacement documents from the applicable manufacturer. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.

7 INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! 1 Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. NOTE: Vehicle Identification Number It is illegal to remove the VIN plate.

8

9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS 2 A Word About Your Keys...12 Key-In-Ignition Reminder...12 Sentry Key If Equipped...12 Ignition And Steering Lock...15 Manual Transmissions...15 Automatic Transmissions...16 Door Key...17 Door Locks...17 Manual Locks...17 Power Door Locks If Equipped...18 Child Protection Door Lock...21 Remote Keyless Entry If Equipped...22 To Unlock The Doors...23 To Lock The Doors...23 Using The Panic Alarm...24 General Information...25 Transmitter Battery Service...25 Security Alarm System If Equipped...26

10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rearming Of The System...26 To Set The Alarm...27 To Disarm The System...27 Windows...28 Power Windows If Equipped...28 Power Sliding Rear Window If Equipped...29 Sliding Rear Window If Equipped...30 Wind Buffeting...30 Occupant Restraints (2500/3500/Mega Cab Only)...30 Lap/Shoulder Belts...31 Adjustable Upper Shoulder Belt Anchorage...38 Automatic Locking Restraint (ALR) Mode If Equipped...39 Center Lap Belts...40 Seat Belt Pretensioners...40 Enhanced Driver Seat Belt Reminder System (BeltAlert)...41 Seat Belts And Pregnant Women...42 Seat Belt Extender...42 Driver And Right Front Passenger Supplemental Restraint System (SRS) Airbag...43 Event Data Recorder (EDR)...54 Child Restraint...55 New Engine Break-In...69 Safety Tips...70 Transporting Passengers...70 Lock Your Vehicle...70

11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Exhaust Gas...71 Safety Checks You Should Make Inside The Vehicle...72 Safety Checks You Should Make Outside The Vehicle

12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. Key-In-Ignition Reminder If you open the driver s door when the key is in the ignition switch, a chime will sound to remind you to remove the key. CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. SENTRY KEY IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for a maximum of 2 seconds after the initial key ON. After six unsuccessful attempts at starting, the system will shut down until the correct key is used. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a

13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 loss of security protection. Additional Sentry Keys or Mobil Speed-pass devices held against or immediately adjacent to the ignition key when starting the engine may cause vehicle starting problems. If a problem occurs, remove the Sentry Key from the key-ring and attempt to start the vehicle again. Pagers, cell phones, walkman, etc. will have no effect on this system. The Security Light, located in the instrument cluster, will illuminate for about 3 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Light will flash continuously to signal that the vehicle has been immobilized. If the Security Light remains on during vehicle operation, it indicates a fault in the system electronics. If this option was ordered, all of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. 2

14 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key. 2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds the Security Light will begin to flash. Turn the ignition back to the OFF position and remove the second key. 3. Insert a blank Sentry Key into the ignition and switch the ignition to the ON position within 60 seconds of having removed the second key. After 10 seconds the Security Light will stop flashing, then turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. The Keyless Entry Transmitter will also be programmed during this procedure. Repeat this process to program up to an additional 6 keys. A maximum of 8 keys can be programmed to the system, including the original keys provided with the vehicle. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.

15 IGNITION AND STEERING LOCK Insert the key fully, and then turn the switch to one of the five illustrated positions. The key can be inserted or withdrawn only in the LOCK position. Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. To remove the key, depress and hold the release button located between the ignition switch and the instrument panel. Turn the ignition key to LOCK and remove the key. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Ignition Switch Positions 2

16 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position. NOTE: The steering wheel will lock when the key is removed, and the steering wheel is turned around 115 degrees from center clockwise and around 65 degrees counterclockwise. Ignition Switch Positions NOTE: On vehicles equipped with an automatic transmission, the key cannot be turned to LOCK until the selector is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position.

17 DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger. Doors locked before closing will remain locked when closed. The ignition key will unlock all the locks on your vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. 2

18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped). Power Door Lock Switch Location As a safety feature the doors will not lock when using the door lock switches during the following condition: The driver s door is open while the key is in the ignition.

19 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 15 seconds cycle the key from the LOCK position to the ON/RUN position a minimum of four times; ending in the LOCK position ( Do not start the engine ). 5. Within 30 seconds, press the driver s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To reactivate this feature, repeat the above steps. 8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure. Auto Unlock Feature This feature unlocks all of the doors of the vehicle when any door is opened. This will occur only after the vehicle has been shifted into the Park position after the vehicle has been driven (shifted out of Park and all doors closed). This feature will not operate if there is any manual operation of the power door locks (Lock or Unlock). 2

20 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming Customer Programming sequence to enable or disable the Auto Unlock Feature: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chimes that may be confusing during this programming procedure). 3. Insert the key into the ignition. 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, program mode was canceled before the feature could be changed. If necessary repeat the above procedure.

21 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the childprotection door lock system. the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. 2 Child Protection Door Lock Location To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage Child Lock Control

22 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY IF EQUIPPED Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. NOTE: For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle. Three Button Transmitter This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.

23 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programmed to unlock all the doors or drivers door only upon the first UNLOCK button press by using the following procedure: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on your key. 3. Continue to hold the LOCK button at least 4 seconds, but no longer than 10 seconds, then press and hold the UNLOCK button while still holding the LOCK button. 4. Release both buttons at the same time. 5. This will enable you to unlock all doors on the first press of the UNLOCK button. To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the LOCK button on a programmed (i.e. functional) key fob. 2

24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. Release both buttons at the same time. 4. To reactivate this feature, repeat the above steps. Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure: 1. Perform this operation while standing outside the vehicle. 2. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob. 3. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the LOCK button. Release both buttons at the same time. 4. To reactivate this feature, repeat the above steps. Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound. To cancel the Panic mode press and release the PANIC button on the transmitter a second time. Panic mode will automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped.

25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. If your Keyless Entry Transmitter fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in transmitter. The expected life of the batteries is from one to two years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service Transmitter Battery Replacement The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. 2

26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries. Be careful not to disturb the metal terminal near the batteries. Install the batteries with the positive terminal up, reference the note + SIDE UP on the inside of the bottom half of the transmitter case. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case snap the two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. SECURITY ALARM SYSTEM IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an additional 15 minutes only the headlights and security telltale will flash. The engine will run only if a valid Sentry Key is used to start the vehicle. Use of the Sentry Key will disable the alarm. Rearming of the System: The security system will rearm itself after the 15 additional minutes of headlights and security telltale flashing, if the system has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condition and monitor the remaining doors and ignition.

27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 To Set the Alarm: The alarm will set when you use the power door locks, or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the SECURITY light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set. After the alarm is set, the security light will flash at a slower rate to indicate that the system is armed. NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer. To Disarm the System: Use the Keyless Entry transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unprogrammed Sentry Key is used to start a vehicle, the engine will run for 2 seconds and then the security alarm will be initiated. To exit alarming mode, press the transmitter Unlock button, or start the vehicle with a programmed Sentry Key. The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit. The door will be locked but the Security Alarm will not arm. 2

28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows If Equipped and on the rear doors of Quad Cab and Mega Cab models. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Power Window Switches The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control Auto Down (Driver s Side Only) The driver s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically.

29 Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button. To enable the window controls, press the window control button again. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Power Sliding Rear Window If Equipped 2 Window Lockout Switch Power Sliding Rear Window Switch The power sliding rear window switch is located on the instrument panel below the climate controls. Press the right side of the switch to open the glass and the left side of the switch to close the glass.

30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Rear Window If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS (2500/3500/MEGA CAB ONLY) Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, window bags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.

31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. 2

32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. WARNING! Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.

33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a click. 2 Latch Plate 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch

34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. And a belt worn under the arm can cause internal injuries. Ribs aren t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. Removing Slack From Belt

35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. A twisted belt can t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.) or if the airbag deployed. 2

36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the vehicle ignition key into the center white slot on the black buckle. The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats. Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.

37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the black latch and black buckle, untwist the webbing, and reattach the black latch and black buckle. Inserting Latch Plate 2

38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. In Use Position Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.

39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Restraint (ALR) Mode If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is available on all passenger seating positions with a combination lap/shoulder belt. When To Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger seating position. Children 12 years old and under should be properly restrained in the rear seat whenever possible. How To Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 2

40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How To Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Center Lap Belts The center seating position for the Quad Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a click. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable. WARNING! A lap belt worn too loose or too high is dangerous. A belt worn too loose can allow you to slip down and under the belt in a collision. A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.

41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the ignition is cycled, driver s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver s seat belt. 2. Start the engine and wait for the Seat Belt Warning Light to turn off. 2

42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender and store it.

43 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 These airbags are certified to the new Federal regulations that allow less forceful deployments. 2 Driver And Right Front Passenger Supplemental Restraint System (SRS) Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver s front airbag is mounted in the center of the steering wheel. The passenger s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.

44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. Do not mount any aftermarket equipment such as trailer brake controllers, snowplow controllers, auxiliary light switches, radios, etc. on or behind the knee bolster. Knee bolsters are designed to work with the air bag and seat belt to protect you. Mounting any additional equipment on or behind the knee bolster can cause injury during a crash. If your vehicle is equipped with window bags, do not stack luggage or other cargo up high enough to block the location of the window bag. The area where the window bag is located should remain free from any obstructions. If your vehicle is equipped with window bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.

45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. Children 12 years and under should ride buckled up in a rear seat, if available. Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause severe injury or death to infants in that position. See the Passenger Airbag On/Off Switch section. If your vehicle does not have a rear seat, see the Passenger Airbag On/Off Switch section. Children that are not big enough to properly wear the vehicle seat belt (see section on Child Restraints) should be secured in the rear seat in child restraints or belt-positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. All occupants should use their seat belts properly. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 2

46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won t deploy at all. Always wear your seat belts even though you have airbags. Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. If the vehicle has window airbags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. Airbag System Components The airbag system consists of the following: Airbag Control Module AIRBAG Readiness Light Driver Airbag Passenger Airbag Steering Wheel and Column Instrument Panel Crash Sensor Interconnecting Wiring Knee Impact Bolsters Passenger Side Frontal Airbag ON/OFF Switch (Standard Cab Vehicles Only)

47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The Window Airbag System, on vehicles equipped, consists of the following: AIRBAG Readiness Light (shared with the front airbag system) Window Bags Above the Side Windows. Airbag Control Module (shared with the front airbag system) Side impact sensors Interconnecting Wiring How The Airbag System Works The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate. The airbag control module will not detect roll over, or rear collisions. The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column. If the key is in the Off position, in the ACC position or not in the ignition, the airbags are not on and will not inflate The airbag control module also turns on the AIR BAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator. 2

48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger. The driver s front airbag deflates through vents towards the instrument panel. The passenger s front airbag is deflated through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle. The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag.

49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Passenger Airbag On/Off Switch (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, has a medical condition which makes passenger airbag inflation (deployment) a greater risk for the passenger than the risk of hitting the dashboard (instrument panel) or windshield in a crash. 2