Description. Safety Guidelines. Specifications. Installation Site. 2 HP - 5 HP Scroll Enclosure Air Compressors

Transcription

1 PREVENT TANK CORROSION kpa pi HP - 5 HP Scroll Encloure Air Compreor Pleae read and ave thee intruction. Read carefully before attempting to aemble, intall, operate or maintain the product decribed. Protect yourelf and other by oberving all afety information. Failure to comply with intruction could reult in peronal injury and/or property damage! Retain intruction for future reference. Decription General The Powerex Oille Rotary Scroll Air Compreor ha advanced croll compreor technology through the development of a completely oille compreor. The Powerex Scroll Compreor offer a dynamically balanced air end which inure vibrationfree operation. The rotary deign permit a continuou 100% duty cycle. Other tandard feature on the Powerex Scroll Compreor include: a Magnetic Starter, Motor Overload Protection, a High Temperature Shutdown Switch, an Air Cooled Aftercooler and a Single Phae or Three Phae 4 Pole ODP motor. WARNING DRAIN MOISTURE FROM TANK EVERY DAY TO Safety Guideline A SEPARATE SAFETY BOOKLET IS PROVIDED ALONG WITH THIS MANUAL. READ AND UNDERSTAND The SAFETY BOOKLET. Thi manual contain information that i very important to know and undertand. Thi information i provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize thi information, oberve the following ymbol. MAKE SURE EVRYONE OPERATING OR SERVICING THE COMPRESSOR READS AND UNDERSTANDS ALL The INFORMATION PROVIDED. Danger indicate an imminently hazardou ituation which, if not avoided, WILL reult in death or eriou injury. Warning indicate a potentially hazardou ituation which, if not avoided, COULD reult in death or eriou injury. Caution indicate a potentially minor or moderate injury. Intallation Intallation Site 1. The croll compreor mut be located in a clean, well lit and well ventilated area. 2. The area hould be free of exceive dut, toxic or flammable gae, moiture, water, and direct unlight. 3. Never intall the compreor where the ambient temperature i higher than 104 o F or where humidity i high. 4. Clearance mut allow for afe, effective inpection Powerex 150 Production Drive Harrion, OH USA Specification Product Performance Specification Lubrication Operating Voltage Compreion Cycle Motor Overload Protection SES Serie Powerex Simplex Air Compreor See Page 2 Greae-filled Bearing 1Ø 3Ø Scroll 230 Volt, 60 Hz; 230 Volt, 50 Hz /460/575 Volt, 60 Hz IEC Motor Overload Relay Preure Setting Cut-In: 95 pig Cut-Out: 115 pig Cut-In: 115 pig Cut-Out: 145 pig (High Preure Unit) Overpreure Protection Outlet Air Connection Tank Size California Ordinance 462 (L) (2) Tank Iolation Drive Control Panel ASME Safety Valve Factory Set and Sealed 3/8 inch NPT 13 Gallon ASME Rated 175 pig Meet Requirement of thi Ordinance Standard All Unit 3V Belt UL508A Lited IN188613AV 12/11

2 Compreor Specification Model SES02 SES03 SES13 SES05 SES15 and maintenance. 20 inche of clearance for ide i recommended. 5. If neceary, ue metal him or leveling pad to level the compreor. Never ue wood to him the compreor. 6. Never intall the compreor outide. 7. For 3 and 5 HP ingle phae model it i recommended that additional tank volume be added. 3 HP ingle phae model need a minimum of 30 gallon air capacity to limit the number of tart-per-hour to 14 maximum. 5 HP ingle phae model need a minimum of 60 gallon air capacity to limit the number of tart-per-hour to 10 maximum. Ventilation 1. If the croll compreor i located in a totally encloed room, an exhaut fan with acce to outide air mut be intalled. 2. Never retrict the cooling fan exhaut air. 3. Vent the exhaut air outide to prevent the compreor from operating at high temperature and hutting down. 4. Never locate the compreor where hot exhaut air from other heat generating unit may be pulled into the unit. Wiring All electrical connection mut be performed by a qualified electrician. Intallation mut be in accordance with local and national electrical code. 1. Make ure power ource i the ame voltage a the unit required voltage 2. Ue olderle terminal to connect the electric power ource. 3. Remove the two left panel. 4. Pull the electric cable through the electric ource inlet and connect to the primary ide of the contact block. 5. Since looening of wire i poible in hipment, tighten all wire terminal prior to tarting the unit. Piping General Guideline 1. Make ure the piping i lined up without being trained or twited when aembling the piping for the croll HP Phae 3Ø 3Ø 1Ø 3Ø 1Ø Voltage / 460 / / 460 / / 460 / Amp See wiring diagram for amp rating Air End SLAE03EB SLAE03EB SLAE05E (SLAE05EHP) Control Sytem Preure Switch Preure Switch Preure Switch Dicharge Preure (PSIG) ( optional) ( optional) ( optional) Air Delivery (CFM) 100 PSIG and 145 PSIG) 100 PSIG and 145 PSIG) 100 PSIG and 145 PSIG) Compreor Speed (RPM) 2200 (1850) 3140 (2770) 3250 (3250) Dicharge Temp. Ambient temp F Ambient temp F Ambient temp F Noie level db(a) [1.5m from front] Dimenion In Inche (L x W x H) 34 x 21 x x 21 x x 21 x 32.5 Approximate Weight 309 lb. 309 lb. 359 lb (Item in paranthei high preure information) compreor. 2. Appropriate expanion loop or bend hould be intalled at the compreor to avoid tree caued by change in hot and cold condition. 3. Piping upport hould be anchored eparately from the compreor to reduce noie and vibration. 4. Never ue any piping maller than the compreor connection. 5. Ue flexible hoe to connect the outlet of the compreor to the piping o that the vibration of the compreor doe not tranfer to the piping. Remote Intake Piping Powerex Compreor Sytem with pipe thread connector on the intake filter are intended for intallation with remote air intake. Piping for the remote intake ytem mut be intalled at the final operating ite. Under ome condition, the intake piping may facilitate the condenation of humidity in the intake air tream into liquid water. The intake filter upplied by Powerex will not top ingetion of liquid water by the pump. Liquid water going into the pump will damage the pump and void the warranty. Alway intall drip leg with ufficient capacity to capture liquid water in the intake piping before the air filter. Drip leg mut be ized with low enough air velocity to make ure they are effective at capturing liquid water in the intake air and mut be maintained (drained) at frequent interval to make ure they remain effective. Safety Valve Tank mounted compreor are hipped from the factory with afety valve intalled in the air receiver manifold. The flow capacity of the afety valve i equal to or greater than the capacity of the compreor. 1. The preure etting of the afety valve mut be equal or le than the maximum working preure of the air receiver. 2

3 2. Safety valve hould be placed ahead of any poible blockage point in the ytem, i.e. hutoff valve. 3. Avoid connecting the afety valve with any tubing or piping. 4. Manually operate the afety valve every ix month to avoid ticking or freezing. Operation Before tart up 1. Make ure all afety warning, label and intruction have been read and undertood before continuing. 2. Remove any hipping material, bracket, etc. 3. Confirm that the electric power ource and ground have been firmly connected. 4. Check the belt for tightne. 5. Be ure all preure connection are tight. 6. Check to be certain all afety relief valve, etc., are correctly intalled. 7. Securely mount all panel and guard. 8. Check that all fue, circuit breaker, etc., are the proper ize. 9. Make ure the inlet filter i properly intalled. 10. Confirm that the drain valve i cloed. tart-up and Operation 1. Viually check the rotation of the compreor pump. The rotation hould be counterclockwie if viewing the compreor from the belt ide. If the rotation i incorrect, have a qualified electrician correct the upply wiring. 2. Follow all the procedure under Before tart-up before attempting operation of the compreor. 3. Make ure compreor witch i in the OFF poition. 4. Switch the electric ource breaker on. 5. Open the 3/8 inch dicharge valve completely. 6. Turn compreor witch to ON poition and check that the compreor operate without exceive vibration, unuual noie or leak. 7. Cloe the dicharge valve completely. 8. If the preure doe not rie on a three phae unit, turn the unit off. Have a qualified electrician witch the breaker OFF and exchange the L1 and L2 connection (two out of three phae of electric ource) on the control panel. 9. Check the dicharge preure. Alo make ure the air preure rie to the deignated preure etting by checking the dicharge preure gauge. 10. Check the operation of the preure witch by opening the outlet valve and confirming the compreor tart at approximately 95 pig for low preure unit and 115 pig or high preure unit. daily Operation 1. Stop the compreor by turning witch to the OFF poition. NOTE: If the compreor rotate in revere for more than five econd, the check valve need to be cleaned or replaced. 2. Switch the breaker OFF if the compreor i not to be ued for a long period of time. topping the Compreor during normal Operation 1. Cloe the dicharge valve. 2. Allow the air preure to build and the compreor to top. 3. Turn the compreor off by turning witch to the OFF poition. Belt Adjutment Procedure 1. Remove the top panel by removing the two lotted 1/4-20 crew on the rear of the encloure. 2. Looen the four (4) motor lide bolt. 3. Tighten belt by adjuting the belt adjutment bolt. Belt tenion for new belt hould be 57 to 65 lb for the looet belt in the et, then lb after run-in. If the belt tenion fall below 25 lb or chirping i heard a tart up, re-tenion belt. (If uing the deflection method for belt tenion, lb force at mid pan hould give 7/32 belt deflection for a new belt, for a ued belt for 7/32 belt deflection. 4. Tighten the four (4) motor lide bolt. Tighten the two electrical panel ide lide bolt firt then tighten the two pulley ide lide bolt. Figure 1 3

4 Scroll Unit Part Breakdown - Model SES02, SES12, SES03, SES13, SES05, SES15, SF120_PHA, and SF130_PHA /4 INCH FNPT TANK DRAIN 3/8 INCH FNPT AIR OUTLET MAIN POWER INLET 4 X DIA Figure 2 4

5 Ref. No. Decription SES02 / SES12 SES03 / SES13 SES05 / SES15 Qty. 1 Air end (low preure) SL014003AJ SL014003AJ SL016502AJ 1 (high preure) SL014003AJ SL014003AJ SL016511AJ gallon tank AR234800AJ AR234800AJ AR234800AJ 1 3 Unit bae SL303600AV SL303600AV SL303600AV 1 4 Front panel SL304500AV SL304500AV SL304500AV 1 5 Right panel SL304400AV SL304400AV SL304400AV 1 6 Back panel SL304600AV SL304600AV SL304600AV 1 7 Top panel SL304800AV SL304800AV SL304800AV 1 8 Utility panel SL305200AV SL305200AV SL305200AV 3 9 Internal duct SL304901AV SL304901AV SL304901AV 1 10 Left panel SL304300AV SL304300AV SL304300AV 1 11 Maintenance panel 1 SL305000AV SL305000AV SL305000AV 1 12 Inide panel SL304700AV SL304700AV SL304700AV 1 13 Pump bae SL304101AV SL304101AV SL304101AV 1 14 Mounting foot IP630300AV IP630300AV IP630300AV 4 15 H upport SL305100AV SL305100AV SL305100AV 2 16 Inlet filter aembly ST073924AV ST073924AV ST073924AV 1 17 Filter element Motor pulley 2HP (low preure, 2-3V4.45) 3Ø PU202633AV Ø PU202623AV 2HP (high preure, 2-3V3.65) 3Ø PU202632AV Ø PU202622AV 3HP (low preure, 2-3V6.0) - PU202625AV - 1 3HP (high preure, 2-3V5.3) - PU202624AV - 1 5HP (low preure, 2-3V6.9) - - PU009754AV 1 5HP (high preure, 2-3V6.9) - - PU009754AV /4 T x 1/4 P x 90 puh connect ST119702AV ST119702AV ST119702AV /4 inch drain tube PS010300AV PS010300AV PS010300AV 2.0 ft. 22 Corner angle ST185500AV ST185500AV ST185500AV 4 23 Temperature 115 pi AM003011AV AM003011AV AM003011AV 1 Temperature 145 pi AM003012AV AM003012AV AM003012AV 1 24 Sub panel SL305300AV SL305300AV SL305300AV /4 inch bulk head fitting PS006701AV PS006701AV PS006701AV /8 inch bulk head fitting PS006702AV PS006702AV PS006702AV 1 27 Safety valve (Low preure unit) V AV V AV V AV 1 (High preure unit) V AV V AV V AV 1 28 Maintenance panel 2 SL306500AV SL306500AV SL306500AV 1 29 Motor lide bae SL306701AV SL306701AV SL306701AV 1 30 Preure witch (Low preure unit) CW207573AV CW207573AV CW207573AV 1 (High preure unit) CW207595AV CW207595AV CW207595AV 1 31 Lighted off/on witch PE000560AV PE000560AV PE000560AV /8 inch ball valve ST079802AV ST079802AV ST079802AV /4 inch ball valve ST079806AV ST079806AV ST079806AV 1 34 Electrical train relief ST188106AV ST188106AV ST188106AV 1 35 Motor 2hp 1 phae MC301579AV hp 3 phae MC303300AV hp 1 phae - MC301579AV - 1 3hp 3 phae ( / 460 V) - MC303301AV - 1 3hp 3 phae (575 V) - MC303302AV - 1 5hp 1 phae - - MC022393AV 1 5hp 3 phae ( / 460 V) - - MC303303AV 1 5hp 3 phae (575 V) - - MC303304AV 1 5

6 Ref. No. Decription SES02 / SES12 SES03 / SES13 SES05 / SES15 Qty. 36 Check valve IP087700AV IP087700AV IP087700AV 1 37 Fan IP632400AV IP632400AV IP632400AV 1 38 Fan guard IP632401AV IP632401AV IP632401AV /8 inch PTFE tube PS001800AV PS001800AV PS001800AV 2.5 ft. 40 Belt 2hp low preure BT009001AV hp high preure BT009001AV hp low preure - BT013800AV - 2 3hp high preure - BT012001AV - 2 5hp low/high preure - - BT010701AV 2 41 High temp light PE000538AV PE000538AV PE000538AV 1 42 Unit preure gauge IP632603AV IP632603AV IP632603AV 1 GA032201AV (PHA UNIT) Hourmeter PE001004AV PE001004AV PE001004AV 1 44 Jic fitting ST186422AV ST186422AV ST186422AV 1 45 Braided hoe SM001502AV SM001502AV SM001502AV 1 46 Rubber mounting block AG007501AV AG007501AV AG007501AV 3 47 After cooler SL300101AV SL300101AV SL300101AV 1 48 u Cabinet crew ST129304AV ST129304AV ST129304AV Fan cord IP632800AV IP632800AV IP632800AV 1 50 Intake adaptor plate IP088400AV IP088400AV IP088400AV 1 51 Adaptor plate gaket IP088200AV IP088200AV IP088200AV /4-20 crew ST074003AV ST074003AV ST074003AV /8 inch PTFE tube PS001800AV PS001800AV PS001800AV 1 ft. 54 3/8 x 3/8 x 90 puh connect ST119705AV ST119705AV ST119705AV 2 Part unique to: SF120_PHA SF130_PHA 3 Deep bae SL305401AV SL305401AV 1 18 Motor pulley (50 Hz) PU202623AV PU202626AV 1 35 Motor (50 Hz) MC301578AV MC301578AV 1 40 Belt (50 Hz) BT012001AV BT010701AV 2 42 Gauge GA032201AV GA032201AV 1 u Swivel cater ST187901AV ST187901AV 4 u = Not hown 6

7 Maintenance Schedule (ee Pump Manual for How To Intruction) Operating Hour Item Action needed ,000 20,000 Remark Receiver Drain moiture Daily If equiped with an Electric Drain, tet daily Cartridge Filter Clean, Replace l Part # Ventilation Screen Clean l Blower Fan Clean l Fan Duct Clean l Compreor Fin Clean l Compreor Regreae (Every 5000 hour for 145 pig unit) Ue genuine Powerex greae Tip Seal Set Replace (Every 5000 hour for 145 pig unit) Heat Inulation Pipe Replace (Every 5000 hour for 145 pig unit) V-belt Inpect, Replace Readjut l Temperature Senor Confirm operation l Preure Switch Confirm operation l Magnetic Starter Inpect l Replace i contact point i deteriorated Safety Valve Confirm operation l Preure Gauge Inpect l Ventilation Fan Inpect l Replace if malfunction l Inpect Replace Note: 1. Inpect and perform maintenance periodically according to maintenance chedule. 2. The maintenance chedule relate to the normal operating condition. If the circumtance and load condition are advere, horten the interval time and perform maintenance accordingly. 3. Marked Readjut mean the tenion of the V-belt hould be adjuted during the initial tage and inpected every 2,500 hour afterward; lb initially, then lb after run-in. 7

8 Electrical Diagram - Single Phae Unit 230 Volt Figure 3 8

9 Electrical Diagram - Three Phae Unit Volt 2 HP - 5 HP Scroll Encloure Air Compreor Figure 4 9

10 DK699800AJ 2 HP - 5 HP Scroll Encloure Air Compreor CR1 PS1 TR1 L1 L2 L3 MSX OLX GND Figure Scroll Electrical Panel Replacement Part Key # Motor Starter / Control Fue 1 / Fue 2 Preure Switch Fue 3 Model HP Overload Relay Tranformer (2 Required) 115 PSI 145 PSI SES V,3P SES V,3P SES V,3P SES V,3P SES V,3P SES V,3P SES V,3P SES V,1P SES V,3P SES V,3P SES V,3P SES V,3P SES V,1P PE000205AV PE000102AV / PE000210AV PE000204AV PE000102AV / PE000206AV PE000102AV / PE000210AV PE000204AV PE000203AV PE000103AV / PE000207AV PE000102AV / PE000207AV PE000102AV / PE000207AV PE000205AV PE000204AV PE000204AV PS005847AV PS005847AV JP007702AV JP007702AV JP007702AV JP007702AV JP007702AV Control Relay JP007711AV CW207573AV CW207595AV PE000403AV 10

11 Troublehooting Guide PROBLEM CAUSE CORRECTIVE ACTION Power ON light doe not 1. Main diconnect i not ON 1. Switch diconnect to ON appear Power ON light i on but unit will not tart Compreor i running but will not make preure Exceive noie or vibration Compreor hut down on high temperature Compreor turn on / off rapidly Safety valve blow off Motor Overload ha tripped 2. Blown fue or circuit breaker at cutomer provided power upply 3. Blown fue at tranformer 4. Lighted witch i burned out 1. Motor overload ha tripped 2. Wrong or low voltage 3. Starter ha failed 4. Motor ha failed 1. Drive belt came off or too looe 2. Clogged intake filter element 3. Preure relief valve ha opened 4. Exceive tip eal wear 5. Electric tank drain i open continuouly 6. Unit running in the wrong direction 7. Dicharge air i leaking 1. Drive belt ha eparated or flat pot 2. Motor ha failed 3. Pump i damaged 4. Cooling air fan i touching fan guard 1. Room temperature i above 104 F 2. Inlet air duct i obtructed 3. Cooling air fan not running 4. Aftercooler fin clogged 5. Intake filter damaged 6. Compreor i dirty 7. Tip eal worn 1. Receiver tank ha high level of water 2. Compreor check valve ha failed 3. Defective preure witch 1. Preure witch ha failed to open 2. Motor tarter contact welded hut 1. Pump ha failed 2. Motor ha failed 3. Improper wiring 4. Wrong overload etting 5. Low voltage 2. Inpect for any fault replace fue or trip diconnect to ON 3. Replace fue - be ure to ue ame type and ize 4. Replace lighted witch 1. See lat entry of Troublehooting Guide 2. Check incoming power upply and unit power rating 3. Replace contactor aembly 4. Replace motor 1. Replace drive belt and (or) tighten 2. Replace intake filter element 3. Preure witch need replaced or motor contact welded hut 4. Replace tip eal 5. Replace tank drain 6. Correct power connection 7. Check dicharge piping 1. Replace drive belt 2. Replace motor 3. Fix or replace pump 4. Check air fan daily 1. Add ventilation or air conditioning to room 2. Remove obtruction or repoition unit to allow for cooling air 3. Replace cooling air fan 4. Clean aftercooler 5. Check intake filter 6. Clean unit 7. Replace tip eal 1. Replace electric tank drain / drain tank 2. Replace check valve 3. Replace preure witch 1. Replace preure witch 2. Replace motor tarter 1. Fix or replace pump 2. Replace motor 3. Check wiring 4. Check overload etting 5. Check incoming power upply 11

12 Powerex Limited Warranty Warranty and Remedie. (a) General. Powerex warrant each Compreor Sytem, Vacuum Sytem, Vacuum Pump, Compreor Air-End, or Powerex branded Acceory (collectively Product, individually each a Product ) to be free from defect in material and workmanhip ( Defect ) at the date of hipment. EXCEPT AS SET FORTH BELOW, NO OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL EXIST IN CONNECTION WITH THE SALE OR USE OF SUCH PRODUCTS. TO THE EXTENT PERMITTED BY LAW, ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. All claim under thi warranty mut be made in writing and delivered to Powerex, or uch claim hall be barred. Upon timely receipt of a claim, Powerex hall inpect the Product claimed to have a Defect, and Powerex hall repair, or, at it option, replace, free of charge, any Product which it determine to have had a Defect at the time of hipment from Powerex; provided, however, that if circumtance are uch a to preclude the remedying of Defect by repair or replacement, Powerex hall, upon return of the Product, refund to buyer any part of the purchae price of uch Product paid to Powerex. Freight for returning Product to Powerex for inpection hall be paid by buyer. The warrantie and remedie herein are the ole and excluive remedy for any breach of warranty or for any other claim baed on any Defect, or nonperformance of the Product, whether baed upon contract, warranty or negligence. b) Initial Period of Warranty Part and Labor. Powerex warrant and repreent all Product hall be free from Defect for the firt twelve (12) month from the date of hipment by Powerex, or five thouand (5,000) hour of ue, whichever occur firt. During uch warranty period, Powerex hall be fully liable for all Defect in the Product (the Product Defect ), i.e., all cot of repair or replacement, which may include in and out charge, o long a the Product are located in the continental United State, and the Product are reaonably located and acceible by ervice peronnel for removal. In and out charge include the cot of removing a Product from buyer equipment for repair or replacement. (c) Additional Period of Warranty Part Only (No Labor). In addition to the above, Powerex warrant each Powerex branded Compreor Air-End, and Vacuum Pump hall be free of Defect for a period of thirty-ix month from the date of hipment of Product, or 10,000 hour of ue, whichever occur firt. Supplier repair or replacement of any Product hall not extend the period of any warranty of any Product. Thi warranty applie to the exchange of part() found to be defective by an Authorized Powerex Service Center only. (d) Coverage. The above mentioned warranty applie to Powerex manufactured unit or ytem only. (e) Exception. Notwithtanding anything to the contrary herein, Powerex hall have no warranty obligation with repect to Product: (i) that have not been intalled in accordance with Powerex written pecification and intruction; (ii) that have not been maintained in accordance with Powerex written intruction; (iii) that have been materially modified without the prior written approval of Powerex; or (iv) that experience failure reulting from operation, either intentional or otherwie, in exce of rated capacitie or in an otherwie improper manner. (f) The warranty provided herein hall not apply to: (i) any defect ariing from corroion, abraion, ue of inoluble lubricant, or negligent attendance to or faulty operation of the Product; (ii) ordinary wear and tear of the Product; or (iii) defect ariing from abnormal condition of temperature, dirt or corroive matter; (iv) any OEM component which i hipped by Powerex with the original manufacturer warranty, which hall be the ole applicable warranty for uch component. Limitation of Liability. TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW, NOTWITHSTANDING ANYTHING TO THE CONTRARY HEREIN, UNDER NO CIRCUMSTANCES SHALL POWEREX BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTAL, PUNITIVE, SPECULATIVE OR INDIRECT LOSSES OR DAMAGES WHATSOEVER ARISING OUT OF OR IN ANY WAY RELATED TO ANY OF THE PRODUCTS OR GOODS SOLD OR AGREED TO BE SOLD BY POWEREX TO BUYER. TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW, POWEREX S LIABILITY IN ALL EVENTS IS LIMITED TO, AND SHALL NOT EXCEED, THE PURCHASE PRICE PAID. Warranty Diclaimer. Powerex ha made a diligent effort to illutrate and decribe the Product in thi literature accurately; however, uch illutration and decription are for the ole purpoe of identification, and do not expre or imply a warranty that the Product are merchantable, or fit for a particular purpoe, or that the Product will necearily conform to the illutration or decription. Product Suitability. Many juridiction have code and regulation governing ale, contruction, intallation, and/or ue of Product for certain purpoe, which may vary from thoe in neighboring area. While Powerex attempt to aure that it Product comply with uch code, it cannot guarantee compliance, and cannot be reponible for how the product i intalled or ued. Before purchae and ue of a Product, pleae review the Product application, and national and local code and regulation, and be ure that the Product, intallation, and ue will comply with them. Claim. Claim pertaining to the Product, with the exception of warranty claim, mut be filed with Powerex within 6 month of the invoice date, or they will not be honored. Price, dicount, and term are ubject to change without notice or a tipulated in pecific Product quotation. All agreement are contingent upon trike, accident, or other caue beyond our control. All hipment are carefully inpected and counted before leaving the factory. Pleae inpect carefully any receipt of Product noting any dicrepancy or damage on the carrier freight bill at the time of delivery. Dicrepancie or damage which obviouly occurred in tranit are the carrier reponibility and related claim hould be made promptly directly to the carrier. Returned Product will not be accepted without prior written authorization by Powerex and deduction from invoice for hortage or damage claim will not be allowed. UNLESS OTHERWISE AGREED TO IN WRITING, THESE TERMS AND CONDITIONS WILL CONTROL IN ANY TRANSACTION WITH POWEREX any different or conflicting term a may appear on any order form now or later ubmitted by the buyer. All order are ubject to acceptance by Powerex. Powerex 150 Production Drive Harrion, OH USA