2D and 2D Watt-Miser. GE Lighting DATA SHEET. Compact Fluorescent Lamps Non-Integrated 16, 21, 28, 38W 2D Watt-Miser and 55W 2D. Product information

Transcription

1 GE Lighting 2D and 2D Watt-Miser Compact Fluorescent Lamps Non-Integrated 16, 21, 28, 38W 2D Watt-Miser and 55W 2D DATA SHEET information Biax 2D compact fluorescent lamps have been available for many years but GE is introducing the next generation of lamps under the name of 2D Watt-Miser. These are available in 16, 21, 28 and 38 Watt in a wide choice of colour temperatures, these lamps are a direct replacement to existing 2D fixtures delivering the same life of 15, hours in case of 28 and 38 Watt but additional energy saving performance, 2D Watt-Miser lamps give similar lumen as the lamps they are replacing but up to 12% energy saving dependent upon ballast and wattage. Saving energy cost: 16W lamp runs on 14W*, 21W lamp runs on 19W*, 28W lamp runs on 24W* and 38W runs on 34W*. In response to the demand from the market for a higher light output version of the 2D lamp, GE offers the 55W using the T5 28W/38W envelope size. The high luminous efficacy has been retained in the 55W by incorporating an amalgam which overcomes the fall in efficacy that occurs with increased lamp loading. The 55W lamp has a cap with dedicated key. The cap material withstands the higher temperatures generated by the increased lamp power while the modified holder key for the 55W 2D will prevent accidental insertion of any lower rated 2D lamp into a 55W socket. The T5 size (14% smaller overall diameter) will allow luminaire manufacturers to design new fittings with improved optical control in addition to the well-known uniformity of light of the Biax 2D concept *When used with electronic ballast Lamp technology In response to the demand from the market for a lower energy consumption GE has invented the extra energy saving 2D Watt-Miser. These lamps are designed to retrofit, into existing fixtures, provide similar lamps performance but save energy at the same time. New 2D Watt-Miser lamps are energy saving compact fluorescent tubes formed into a 2D shape. All types are available with a 4pin cap which permits use with conventional or electronic (high frequency) control gear, dimming and emergency lighting circuits. The 16-28W types are also available with 2pin cap which contains a starter switch and an EMC (RIS) capacitor. Features 16 & 28W 2D Watt-Miser lamp available in 2 & 4-pin versions 2-pin design with internal starter 4-pin design optimised for high frequency operation and also suitable for emergency lighting 21 & 38W 2D Watt-Miser lamp available only in 4-pin version Excellent colour rendering CRI Ra 82 Compatible with existing ballasts and fittings.

2 Application areas Residential Domestic Hotels/motels/restaurants Utility areas Task lighting Emergency lighting The flat profile makes the 2D Watt-Miser an ideal choice for building into slim, attractive luminaries. Its two dimensional shape is suitable for both up lighting and downlighting applications, where directional lighting is required. Due to its shallow, broad configuration, it spreads light over a large area without the need for expensive optics. Basic data Wattage [W] Wattage on Gear [W] Energy consumption [kwh/h] Volts 5Hz [V] Biax 2D Watt-Miser 2-pin, Internal Starter Description Code Blister Code Hanging Box Lumen [lm] Lumen [lm] Lamp Efficacy on Gear GR8 F162D/827 GE 2PK 41744** K 3. 12, A GR8 F162D/835 GE 2PK 41745* K 3. 12, A GR8 F162D/86 GE 2PK 41749** K 3. 12, A GR8 F282DT5/827/2P BL 1/2 WM 1546* K 3. 15, A GR8 F162D/T4/827/2P GE HB 1/1 WM K 3. 12, A GR8 F162D/T4/835/2P GE HB 1/1 WM K 3. 12, A GR8 F162D/T4/86/2P GE HB 1/1 WM K 3. 12, A GR8 F282D/T5/827/2P GE HB 1/1 WM K 3. 15, A Biax 2D /E Watt-Miser 4-pin, External Starter Required GR1q F162D/827/4P GE 2PK 41746** , A GR1q F162D/83/4P BL1/2 WM , A GR1q F162D/835/4P GE 2PK 41747** , A GR1q F16 2D/84/4P OEM12PK WM , A GR1q F212D/827/4P GE 2PK 41794** , A GR1q F212D/835/4P GE 2PK 4186** , A GR1q F212D/86/4P GE 2PK 4188*** , A GR1q F282DT5/827/4P BL 1/2 WM 1547** , A GR1q F282D/83/4P BL1/2 WM 7568*** , A GR1q F282DT5/835/4P BL 1/2 WM 1567* , A GR1q F282DT5/84/4P BL 1/2 WM 1548* , A GR1q F382DT5/827/4P BL 1/2 WM 155* , A GR1q F382D/83/4P BL1/2 WM , A GR1q F382DT5/835/4P BL 1/2 WM 1566* , A GR1q F382DT5/84/4P OEM32PK SLVLESS WM , A GR1q F382D/T5/86/4P LEG BL 1/2 WM 78336*** , A GR1q F162D/T4/827/4P GE HB 1/1 WM , A GR1q F162D/T4/835/4P GE HB 1/1 WM , A GR1q F212D/T4/827/4P GE HB 1/1 WM , A GR1q F212D/T4/835/4P GE HB 1/1 WM , A GR1q F212D/T4/86/4P GE HB 1/1 WM , A GR1q F282D/T5/827/4P GE HB 1/1 WM , A GR1q F282D/T5/83/4P GE HB1/1 WM , A GR1q F282D/T5/835/4P GE HB 1/1 WM , A GR1q F282D/T5/84/4P GE HB 1/1 WM , A GR1q F382D/T5/827/4P GE HB 1/1 WM , A GR1q F382D/T5/835/4P GE HB 1/1 WM , A GR1q F382D/T5/86/4P LEG HB 1/1 WM , A *Blister SKUs will be phased out, only Hanging box version will be available after inventory run out. **Will be phased out at latest April 215. ***Will be phased out at latest October 215. CCT [K] Mercury [mg] Life 5Hz 3h [h] EEC 2

3 Wattage [W] Wattage on Gear [W] Energy consumption [kwh/h] Volts 5Hz [V] Biax 2D 4-pin, External Starter Required Spectral power distribution Description Code Blister Code Hanging Box Lumen [lm] Lumen [lm] Lamp Efficacy on Gear GR1q-3 F552D/T5/827/A/4P LEG BL 1/ * K 3 1, A GR1q-3 F552D/T5/83/4P A/T LEG BL 1/ * K 3 1, A GR1q-3 F552D/T5/835/A/4P LEG BL 1/2 7834* K 3 1, A GR1q-3 F552D/T5/827/4P A LEG HB 1/ K 3 1, A GR1q-3 F552D/T5/83/4P A/T LEG HB 1/ K 3 1, A GR1q-3 F552D/T5/835/4P A LEG HB 1/ K 3 1, A *Blister SKUs will be phased out, only Hanging box version will be available after inventory run out. Note: CRI: 82, mercury: 3.mg, pack quantity: 2, life on electrical gear [h]: see page 4. CCT [K] Mercury [mg] Life 5Hz 3h [h] EEC CCT [K] 25 Spectral power distribution 27K x y CRI [Ra] 25 Spectral power distribution 27K Spectral power distribution 3K Spectral Spectral power power distribution 35K 3K Wavelength [nm] 25 Spectral power distribution 4K Spectral power power distribution 6K 4K

4 Dimensions 2D T4 2D T5 2D Watt-Miser 16W on standard gear 3h 2D T5 WL % 9% 8% 7% 6% 5% 2, 4, 6, 8, 1, 12, Wattage A (max) [mm] B (max) [mm] C [mm] D [mm] 16W W W W W WL W WL W WL CAPS/Connection s: % 9% 8% 7% 6% 16-28W 2pin GR8 2D Watt-Miser 21W on standard gear 3h 16, 21, 28 and 38W 4pin GR1q 55W 4pin GR1q-3 Lamp life Cathodes of a fluorescent lamp lose their electronemisivity during life due to the evaporation of emission mixture. When the deterioration reaches a certain level, the cathode breaks. Typical lifetime Life expectancy characteristics and lumen are based maintenance on GE Lighting s 2D Watt-Miser 28-38W on electronic gear 3h and 12h measurements according to the relevant IEC standards. The declared lamp life is the median life, which is when 5% of the % lamps from a large sample batch would have failed. Real lifetime figures may depend on actual application. For instance improper cathode preheat, too high operating current, or too low operating current without additional cathode heating 88% reduces the expected life. 75% Test conditions: Horizontal burning position 63% Switching cycle: 165 minutes on 15 minutes off (3h) and 11h ON 1h OFF (12h) 5Hz line frequency operation 5% 25 C ambient temperature 5% 2, 4, 6, 8, 1, 12, Survival rate 12 hours 2, 4, 6, 8, 1, 12, 14, 16, 18, 2, 22, % 2D Watt-Miser 16W on standard gear 3h % 2D Watt-Miser 28W on standard gear 3h 9% 8% 7% 6% 88% 75% 63% 5% 2, 4, 6, 8, 1, 12, 5% 2, 4, 6, 8, 1, 12, 14, 16, % 2D Watt-Miser 21W on standard gear 3h % 2D Watt-Miser 55W on standard gear 3h 9% 8% 7% 6% 9% 8% 7% 6% 5% 2, 4, 6, 8, 1, 12, 2D Watt-Miser 28-38W on electronic gear 3h and 12h 5% %

5 2, 4, 6, 8, 1, 12, % 2D Watt-Miser 28-38W on electronic gear 3h and 12h 88% 75% 63% Survival rate 12 hours The impact Life expectancy on life of alternative and lumen switching maintenance cycles is shown in the graph Life versus frequency of switching. For very frequent 2D Watt-Miser 28W on standard gear 3h switching % applications it is possible to minimise the adverse effect of short on periods with the use of a suitable electronic starter. For lamps with an integral starter switch (2pin), the switch is designed to give approximately 2, starts which may 88% be of more relevance than rated lamp life in a frequently switched situation. To achieve claimed life for high frequency operation a preheated start is recommended. 5% 2, 4, 6, 8, 1, 12, 14, 16, 18, 2, 22, 75% 2 63% Life versus frequency of switching Relative life 5% 15 2, 4, 6, 8, 1, 12, 14, 16, 2D Watt-Miser 55W on standard gear 3h 5 % Electronic gear gear 9% % 7% Lumen 6% maintenance Hours/switching The lumen 5% maintenance graph shows how the light output decreases throughout life. The main causes of the light depreciation are the deterioration of phosphor coating and end blackening due to the deposition of evaporated emission mixture on the glass tube. These effects are normal and unavoidable. The lumen maintenance curve given below for 2D Watt-Miser lamps is based on lumen readings under laboratory conditions. Test conditions: Photometric sphere Horizontal burning position Switching cycle: 165 minutes On 15 minutes Off 5Hz line frequency operation 25 C ambient temperature Lamp starting The graph Starting voltage vs. ambient temperature shows electronic ballast open circuit voltage required for starting as a function of ambient air temperature. Data is based on measurements carried out by GE Lighting under controlled test conditions. Actual lamp starting voltage figures depend on the overall characteristics of electronic ballast. Appropriate preheating of cathodes is necessary in order to achieve low starting voltage and long lamp life. Starting voltage (V) Starting voltages vs. ambient temperature 16W 21W 28W 38W 55W Ambient temperature ( C) 5

6 Test conditions: Horizontal lamp position Thermal chamber providing ±2 C accuracy 2s current controlled preheat Sufficient preheat current Voltage ramp-up until ignition Ambient temperature [ C] Starting voltage [V eff ] 16W 21W 28W 38W 55W Minimum Starting Temperature Lamp starting at low ambient temperatures can be successfully achieved, however light output during initial warm-up will be considerably reduced, but will gradually increase as lamp temperature rises. Use of an electronic starter or electronic ballast is recommended for lower ambient temperature applications. Satisfactory starting at lower ambient temperatures requires a close proximity earth (ground) plate. Use of an electromagnetic ballast and glow starter is not recommended for applications below C. Run-Up Time When a fluorescent tube is switched on light output rises during the first few minutes until the optimum temperature is reached, but then falls if the temperature continues to rise. Amalgam lamp technology provides maximum light output at a higher lamp operating temperature than standard liquid mercury dose technology, but warm-up time is longer. However the slower fall-off in light output at higher ambient/operating temperatures allows greater flexibility in luminaire design. As a consequence of the slower run-up characteristic amalgam lamps are not considered suitable for applications involving severe under-running associated with emergency lighting applications; where very short onperiods are likely or where low ambient temperatures are encountered, unless the fitting is fully enclosed. Lumen [%] Run-up time Time [s] 28W Watt-Miser 38W Watt-Miser 16W Watt-Miser 21W Watt-Miser 55W T5 Preheating requirements Suitable preheating of cathodes prior to ignition is essential for long lamp life. The preheating requirement can be given by the following formula: E = Q + P t This energy is measured on a substitution resistor Q stands for the necessary thermal energy. P represents the power loss due to the heat transmission from the cathode. The longer the preheating, the more the power loss. The two basic preheating modes, the current controlled and the voltage controlled modes, can be derived from the formula. Description Minimum energy Maximum energy [Q] [P] [R sub ] [Q] [P] [R sub ] 16W W W W Preheat energy [J] 1 7,5 5 Preheat energy vs time Emin - 16w Emin - 21w Emin - 28w Emin - 38w Emax - 16w Emax - 21w Emax - 28w Emax - 38w 2,5 1,25 2,5 3,75 5 Preheat time [s] 6

7 Influence of ambient air temperature Lamp performance The lamp performance parameters, such as luminous output, lamp voltage and power depend on the mercury vapour pressure in the discharge tube. The mercury vapour pressure is a function of the thermal conditions around the lamp. The burning position, air flow, and radiated heat have an effect on these conditions. The curve shows the relative luminous output as function of the ambient temperature in horizontal burning positions. Tests were performed in draught-free air under thermally controlled conditions. Test conditions: Thermal chamber with ±2 C accuracy Draught-free air Relative luminous output % Light output vs. ambient temperature 16W 21W 28W 38W 55W Ambient Temperature in C Luminous intensity distribution The following diagrams show the polar light intensity distribution of the 2D Watt-Miser 28-38W lamp. Burning position: horizontal o o o o o o o o o o o o I (cd) I (cd) o o o o o o o o o o 9 o 9 o 75 o 75 o o o 6 o o o o o 3 o 3 o 45 o 45 o G9 G9 Burning position: vertical o o o o 9 o 9 o 75 o 75 o 6 o 6 o I (cd) I (cd) I max I max = = cd cd at 177 at 177 o o o 15 o 15 o o o o o 135 o 135 o o o o o o o 9 o o 75 o o 6 o o 45 o 3 o 3 o o o 3 o 3 o 45 o 45 o C 18 C 18 C 27 C 27 C C C9 C9 Ballast compability * 7 Burning position: horizontal Burning position: vertical Control Gear - High Frequency (electronic gear) I (cd) I (cd) I max I max = = cd cd at 177 at 177 o o Watt Manufacturer I (cd) Catalogue I (cd) Code Dimmable Emergency Comment o o o o o o o o o o o 15 o 15 o o o o o 135 o 135 o o 16 TRIDONIC PC 1/1/13 TCD PRO o o o o 16 TRIDONIC PC 1x5-16W BASIC o o TRIDONIC PCA 1/18 ECO o o TRIDONIC 75 PC PRO FSQ b o o o o 21 OSRAM QT-ECO x1x18-24/22-24l High TDH%, low power factor ballast o o HELVAR EL 1/2x18-42TC o o HÜCO BL-HP 251x28W TC-DD HC DIM 9 o 9 o o 9 o o o HÜCO BL 1x28W TC-DD HMC 9 o 9 o High TDH%, low power factor ballast 28 VOSSLOH ELXc o 75 o 75 o 75 o o o OSRAM QUICKTRONIC QT-M1x o o TRIDONIC PC 1x28DD PRO TRIDONIC PC 75 1x HO DD COMBO o o HELVAR EL 162x18-42TC 6 o 6 o 6 o 6 o o 6 o 38 HÜCO BL-HP1x38W TC-DD HC DIM HÜCO BL-HP 1x38W TC-DD HC TRIDONIC o o o o PC o 1x38W o DD 3PRO o o 45 o 45 o 38 TRIDONIC PC 1x38-34 DD COMBO 45 o 45 o 3 o 3 o o o 3 o 3 o 45 o 45 o 38 G9 G9 OSRAM QUICKTRONIC QT-M 1x26-42 C 18 C 18 C 27 C 27 C C C9 C9 38 VOSSLOH ELXc ERC Mectronic SQU

8 Control Gear - Mains Frequency (standard gear) Watt Volt Manufacturer Catalogue Code Tridonic. Atco EC16 B27 23/ Helvar L16D/ Helvar L16DL/ ERC MEC92 16W ERC MEC75/NANO 16W Tridonic. Atco EC16 B27 24/ Helvar L16D/ Helvar L16DL/ Vossloh-Schwabe L ERC MEC92 16W ERC MEC75/NANO 16W Helvar L21TL Vossloh-Schwabe L Tridonic. Atco EC21 B51K 23/ Tridonic. Atco EC21 B52K 23/ ERC MEC4-LB/28W Helvar L18TL Helvar L18TLB Tridonic. Atco EC18B51K Tridonic. Atco EC18LC51K Vossloh-Schwabe LN ERC MECO4-LB/28W Helvar L18TL Helvar L18TLB Tridonic. Atco EC18B52K Tridonic. Atco EC18LC52K Vossloh-Schwabe LN ERC MEC4-LB/36-4W Helvar L36TL Helvar L36TLB Tridonic. Atco EC36B51K Tridonic. Atco EC36TLB51K Vossloh-Schwabe LN ERC MEC4-LB/36-4W Helvar L36TL Helvar L36TLB Tridonic. Atco EC36B52K Tridonic. Atco EC36TLB52K Vossloh-Schwabe LN36.55 *Ballast manufacturers have the right to change ballast specification without prior notification or official announcement so these data based on GE measurement 21/211. Gear specification Cathode resistances Power datasheet 691-IEC Test current [A] Cathode test min [Ohm] max 16 GR1q 316* GR1q 321* GR1q 328* GR1q 338* GR1q3 355* Cathode preheat requirements Power datasheet 691-IEC E min = Q min + P min *ts Q min [J] P min [W] R sub,min Cathode test min [Ohm] max 16 GR1q 316* GR1q 321* GR1q 328* GR1q 338* Dimming requirements Power datasheet 691-IEC Id min [A] Id max [A] X [A2] Y [A] 16 GR1q 316* GR1q 321* GR1q 328* GR1q 338* Starting requirements Power datasheet 691-IEC Ignition voltage [V rms ] Non-ignition voltage [V rms ] R sub 16 GR1q 316* GR1q 321* GR1q 328* GR1q 338* GR1q3 355* * proposal to IEC * proposal to IEC 8

9 Operating notes 2-pin 2D Watt-Miser lamps are unsuitable for use in dimming circuits or from an electronic ballast and should not be used for these applications. The 4-pin 2D Watt-Miser lamps can be operated from electronic control gear and dimmed using appropriate control gear. The 2D Watt- Miser lamps can be operated in any position except where leg a is higher than bends b in case of 38W types. This limitation is necessary to ensure that region Ø of cap is kept as cool as possible. Circuit diagrams Operating position β Φ α 2-pin, electromagnetic ballast (single lamp) 4-pin, electronic ballast (single lamp) Mains N P LH = Lamp Holder B = Ballast B LH = Lamp Holder E = Electronic Gear E LH LH 4-pin, automatically switched emergency lighting 4-pin, electronic dimming ballast LH = Lamp Holder E = Electronic Gear EG = Emergency Gear B = Battery E LH = Lamp Holder E = Electronic Gear D = Dimmer S = Sensor or control Mains N P Mains P N EG B LH S D E LH Additional notes All 2D Watt-Miser lamps have a long tip-off tube which acts as a cool spot into which the liquid mercury reservoir (required by all fluorescent lamps) migrates during early lamp operation. In relation to circuit or fittings design or ballast evaluation, tests should be conducted with lamps aged to a minimum of 5 hours with care being taken to keep the mercury in this cool spot. In practice this means either the lamp should be left undisturbed in the ageing position or if the lamp is moved avoid mechanical shock. The 2D loops should be kept above the straight lamp region (9 bends). This procedure is recommended to ensure that liquid mercury is fully retained in the cool spot tip-off tube. 4-pin lamps can be operated directly from 22/25V 5/6Hz mains supplies using an electromagnetic ballast and external glow or electronic starter. Recommended GE glow starters are 155/5 and 155/4. 2D Watt-Miser 16, 21, 28 and 38W lamps operate flicker-free only with GE 155/4 starters. For supply voltages above or below the range 22/25V, a transformer or other suitable means of adjusting the supply voltage is necessary. Operation from an electronic ballast maximises lamp photometric and survival performance. 2D Watt-Miser lamps are standardised internationally through the International Electrotechnical Commission (IEC). For lamp performance the relevant data sheets in IEC 691 (EN 691) apply and for lamp safety the relevant clauses in IEC apply. Watt-Miser, Biax and 2D are registered protected trademarks. Unapproved use of trademarks are illegal. 9

10 Compliance s IEC IEC or EN 691 IEC or EN CIE S 9/E:22 European Directives CE mark Energy Labelling RoHS WEEE REACH ErP ecodesign Lamp caps and holders together with gauges for the control of interchangeablity and safety Single-capped lamps - performance requirements Single-capped lamps - safety requirements Photobiological safety of lamps and lamp systems 93/68/EEC; LVD: 26/95/EC; Ecodesign 25/32/EC, ROHS 211/65/EU Directive 21/3/EU, 874/212/EU energy labelling of electrical lamps and luminaires Directive 211/65/EU on Restrictions of the use of certain Hazardous Substances (RoHS) Directive 212/19/EU on Waste Electrical and Electronic Equipment (WEEE) Directive 26/197/EC on Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) Directive 25/32/EC, 29/245/EC ecodesign requirements (of Energy-related s) for tertiary sector lamps and General Electric are both registered trademarks of the General Electric Company GE Lighting is constantly developing and improving its products. For this reason, all product descriptions in this brochure are intended as a general guide, and we may change specifications time to time in the interest of product development, without prior notification or public announcement. All descriptions in this publication present only general particulars of the goods to which they refer and shall not form part of any contract. Data in this guide has been obtained in controlled experimental conditions. However, GE Lighting cannot accept any liability arising from the reliance on such data to the extent permitted by law. 2D and 2D Watt-Miser Data Sheet June 215