Advanced Battery Charger Considerations for Portable Devices. Jinrong Qian Richard Stair
|
|
|
- Norman Gordon Perry
- 7 years ago
- Views:
Transcription
1 Advanced Battery Charger Considerations for Portable Devices Jinrong Qian Richard Stair Battery Charge Management Texas Instruments Battery Power
2 Li-Ion Charge CC-CV Profile Constant Current Pre-charge Fast-charge 4.2 V/Cell I CHARGE Constant Voltage Battery Voltage Capacity 3.0 V/Cell Taper Current I PRECHARGE Pre-charge Timer Safety Timer I TERMINATION Constant Current: 20-30% charging time, 70-80% capacity Constant Voltage: 70-80% charging time, 20-30% capacity Battery Power
3 Battery Charger Topologies Battery Power
4 Charger Requirements for Portable Devices Input Power Source Adapter: 5V, 9V, and 12V up to 2A (24W) USB2.0: (many systems) USB3.0: Battery System Performance: Support dynamic system pulsating power Fast and high efficiency charging Supporting all kinds of battery chemistry Thermal management Battery Power
5 Charging with an Active System Load + Adapter or USB Charger I CHG I SYS I BAT System Charger output current is shared: I CHG = I BAT + I SYS Issues: Operate system and charging simultaneously Safety Timer Termination Battery Power
6 Linear Charger with DPM Architecture Adapter Powering System + - Q1 Controller Q2 Charging Battery C1 System Separate charge current path from system current path Charge current controlled by Q2 Powering System from adapter through Q1 Simultaneously powering system and charging battery Linear Charger Battery Power
7 Switch-Mode Battery Charger with DPM I IN Q2 A2 - Control + Loops Q3 I CHG Q4 VBUS I SYS I SYS I IN I SYS1 I SYS2 DPM Mode Adapter Limit I REF + - BAT I CHG Input Current Regulation V REF Maximize use of the input current Current sharing between system & charger Minimize the AC adapter size and power rating How to avoid adapter crash if its current is NOT Known? Battery Power t1 t2
8 Consideration 1: How to Support unknown Adapter? Input Voltage Regulation DPM V IN I IN Q1 Q2 VBUS A2 - Control + Loops Q3 I CHG Q4 I SYS VINDPM + - BAT V REF If VIN < VINDPM; D ICHG IIN VIN = VINDPM Automatically Track Adapter s Max Current. Perfect for third party adapter Battery Power
9 Consideration 2: How to Support Pulsating Load? Supplement Mode Operation VIN/USB Q1 Q2 L VBUS Q4 Q3 ICHG System VBAT 3.0V 3.4V VBUS VBAT 4.2V Time Pre-charge: Q4 -- Linear Mode, Fast Charge: Q4 = ON ICHG t1 Pre-Charge t2 t3 Fast-Charge Battery Power
10 Consideration 3: How To Reduce the Battery Charging? High Current Charging IR Compensation 1. Extending the Constant Current mode 2. Reducing the Constant Voltage charging time Battery Power
11 Battery Charging Time VREG CC Mode ONLY ICHG 4.2V VREG I CHG C + - CC: t1 CC/CV + - VREG R C + - OCV 4.2V I CHG I R CC: t1 VREG OCV R C CV: t2 Goal: VREG = 4.2V + IR (R = Rdson + Rsense+ Trace resistance) Battery Power
12 Battery Charging Profile with IR Compensation Longer constant current phase and shorter constant voltage phase reduces total charge time. Battery Power
13 Consideration 4: How To Support USB OTG? Boost 0.1A 0.5A 0.9A Q1 Q2 Q3 Q4 ICHG VBUS VBAT System Bidirectional Synchronous Buck: a. Charge in Buck b. Discharge in Boost for USB OTG Save an additional Boost converter Battery Power
14 Design Examples Battery Power
15 4A I2C Single Cell Battery Charger Support DC Adaptor, USB2.0 and USB 3.0 up to 3A USB Input 3.9V 17V VREF D+/D- Detection I2C Interface REGN VBUS Q1 4x4mm^2 QFN-24Pin Package PMID D+ D- STAT Q2 Q3 Q4 SW BOOT REGN PGND SYS BAT SYS: 3.4V-4.4V Integration of power path and switching MOSFETs Up to 4A Charge Current and 6A Discharge Current Host USB On-The-Go Default USB Current SDA SCL INT OTG /CE ILIM bq24190 Thermal PAD TS1 TS2 REGN Input Current Setting Dual battery Pack Thermistor Monitoring Battery Power
16 Thermal Performance (IC Case Temperature) bq24190 PG10 Case Temperature 80 Case Temperature (C) VBUS=5V, VBAT=3.8V VBUS=9V,VBAT=3.8V VBUS=12V,VBAT=3.8V ICHG (A) VBAT=3.8V, Ta= 31ºC Battery Power 2012
17 System Efficiency Measured on EVM 96.00% 94.00% 92.00% VBUS 5V VBUS 9V VBUS 12V Efficiency 90.00% 88.00% 86.00% 84.00% Charge Current ((A) VBAT=3.8V with 2.2uH inductor Battery Power 2012
18 Summary Charger Topology: Linear vs Switching Mode charger How to Support all kinds of Power Source and USB? Fast Charging: high charge current and IR Compensation Design Examples Battery Power
Designing Applications with Lithium-Ion Batteries
Application Note Roland van Roy AN025 Sep 2014 Designing Applications with Lithium-Ion Batteries Contents 1. Introduction...1 2. Single Li-Ion Cell as Power Source...2 3. Battery Charging...6 4. Battery
FAN54015 USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator
October 2013 FAN54015 USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator Features Fully Integrated, High-Efficiency Charger for Single-Cell Li-Ion and Li-Polymer Battery Packs
Bi-directional Power System for Laptop Computers
Bi-directional Power System for Laptop Computers Terry L. Cleveland Staff Applications Engineer Microchip Technology Inc. Terry.Cleveland@Microchip.com Abstract- Today the typical laptop computer uses
Power management for handheld and portable applications. A tradition of leadership in power management is now mobile
Power management for handheld and portable applications A tradition of leadership in power management is now mobile Leaders in PM for Mobile Advanced analog power management ICs Integrated devices with
Battery Charging Technology. May 2015 Speaker: John Hsiao
Battery Charging Technology May 2015 Speaker: John Hsiao Applications Power Banks Power Tools Energy Harvesting Solar Power Forklifts Uninterruptable Power Supply (UPS) Industrial Lighting Portable Industrial
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 735 LITHIUM-ION LINEAR BATTERY CHARGER WITH LDO REGULATOR
DESCRIPTION QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 735 LTC4063EDD Demonstration circuit 735 is a complete constantcurrent, constant-voltage battery charger for one Lithium-Ion cell and includes a
RT9515. Linear Single Cell Li-Ion Battery Charger IC. General Description. Features. Applications. Ordering Information RT9515. Pin Configurations
Linear Single Cell Li-Ion Battery Charger IC General Description The RT515 is a fully integrated low cost single-cell Li- Ion battery charger IC ideal for portable applications. The RT515 is capable of
AN2389 Application note
Application note An MCU-based low cost non-inverting buck-boost converter for battery chargers Introduction As the demand for rechargeable batteries increases, so does the demand for battery chargers.
"Charging Lithium-Ion Batteries: Not All Charging Systems Are Created Equal"
"Charging Lithium-Ion Batteries: Not All Charging Systems Are Created Equal" By Scott Dearborn Principal Applications Engineer Microchip Technology Inc. 2355 West Chandler Blvd Chandler, AZ 85224 www.microchip.com
Solar Mobile charging Solutions
Solar Mobile charging Solutions Solar power is one of the widely available energy sources. It has been in focus worldwide and solar installations of capacities in megawatts order are reality today. The
Smart Battery Module with LEDs and Pack Supervisor
Features Complete smart battery management solution for Li-Ion battery packs Accurate measurement of available battery capacity Provides overvoltage, undervoltage, and overcurrent protection Designed for
2.996/6.971 Biomedical Devices Design Laboratory Lecture 4: Power Supplies
2.996/6.971 Biomedical Devices Design Laboratory Lecture 4: Power Supplies Instructor: Dr. Hong Ma Sept. 19, 2007 Key Problem Ideal voltage sources do not exist! Voltage regulators use feedback to reduce
AC/DC Power Supply Reference Design. Advanced SMPS Applications using the dspic DSC SMPS Family
AC/DC Power Supply Reference Design Advanced SMPS Applications using the dspic DSC SMPS Family dspic30f SMPS Family Excellent for Digital Power Conversion Internal hi-res PWM Internal high speed ADC Internal
400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
Features Wide 5V to 32V Input Voltage Range Positive or Negative Output Voltage Programming with a Single Feedback Pin Current Mode Control Provides Excellent Transient Response 1.25V reference adjustable
DESIGN OF A BATTERY CHARGER INTERFACE PRECHARGE FOR MOBILE PHONE
DESIGN OF A BATTERY CHARGER INTERFACE PRECHARGE FOR MOBILE PHONE Karim El khadiri1 and Hassan Qjidaa2 Université Sidi Mohamed Ben Abdellah Faculté des sciences Dhar El Mehraz Laboratoire d Electronique
POWER FORUM, BOLOGNA 20-09-2012
POWER FORUM, BOLOGNA 20-09-2012 Convertitori DC/DC ad alta densità di potenza e bassa impedenza termica. Massimo GAVIOLI. Senior Field Application Engineer. Intersil SIMPLY SMARTER Challenges when Designing
APPLICATION NOTE ANP17
Solved by APPLICATION NOTE ANP17 TM Design Considerations For Cell Phone Camera Flash Drivers Introduction Hundreds of kinds of cell phones are appearing on the market every year and they all have the
Battery Cell Balancing: What to Balance and How
Battery Cell Balancing: What to Balance and How Yevgen Barsukov, Texas Instruments ABSTRACT Different algorithms of cell balancing are often discussed when multiple serial cells are used in a battery pack
Building Battery Arrays with Lithium-Ion Cells
Building Battery Arrays with Lithium-Ion Cells About the Sponsor Micro Power Electronics Design and manufacture of lithium battery packs, chargers and power supplies for mission-critical applications OEM
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at:
Welcome to this presentation on Switch Mode Drivers, part of OSRAM Opto Semiconductors LED Fundamentals series. In this presentation we will look at: How switch mode drivers work, switch mode driver topologies,
Isolation of Battery Chargers Integrated Into Printed Circuit Boards
LLNL-TR-646864 Isolation of Battery Chargers Integrated Into Printed Circuit Boards J. S. Sullivan November 26, 2013 Disclaimer This document was prepared as an account of work sponsored by an agency of
bq2114 NiCd or NiMH Gas Gauge Module with Charge-Control Output Features General Description Pin Descriptions
Features Complete bq2014 Gas Gauge solution for NiCd or NiMH battery packs Charge-control output allows communication to external charge controller (bq2004) Battery information available over a single-wire
ISL9204. Features. High Input Voltage Charger. Applications. Ordering Information. Pinout. Data Sheet October 4, 2005 FN9207.0
ISL9204 Data Sheet FN9207.0 High Input Voltage Charger The ISL9204 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger. This charger performs the CC/CV charge function
ST-828 NiCd / NiMH / Li-Ion Battery Seq. Twin Charge Control IC
NiCd / NiMH / Li-Ion Battery Seq. Twin Charge Control IC Available Now!!! Main Function For NiCd / NiMH battery apply constant-current (C.C.) charge technique and provide - V/ t, Timer, V-Max, terminatecondition
Bi-directional FlipFET TM MOSFETs for Cell Phone Battery Protection Circuits
Bi-directional FlipFET TM MOSFETs for Cell Phone Battery Protection Circuits As presented at PCIM 2001 Authors: *Mark Pavier, *Hazel Schofield, *Tim Sammon, **Aram Arzumanyan, **Ritu Sodhi, **Dan Kinzer
IEC 62133 2 nd Edition: All you need to know about the new standard
IEC 62133 2 nd Edition: All you need to know about the new standard Laurie Florence Principal Engineer Batteries, Fuel Cells & Capacitors UL LLC THESE UPDATES ARE FOR INFORMATION PURPOSES ONLY AND ARE
VARTA EasyPack. design-in handbook. The easy way to power portable devices! See also: http://www.varta-microbattery.com/top/ezp
VARTA EasyPack design-in handbook The easy way to power portable devices! See also: http://www.varta-microbattery.com/top/ezp VARTA EasyPack design-in handbook Page 1 of 14 VARTA Microbattery GmbH Table
RECHARGEABLE BATTERY CONSIDERATIONS IN PORTABLE EQUIPMENT
SECTION 5 BATTERY CHARGERS Walt Kester, Joe Buxton INTRODUCTION Rechargeable batteries are vital to portable electronic equipment such as laptop computers and cell phones. Fast charging circuits must be
LED Drivers For Lighting
LED Drivers For Lighting Dongwoon Anatech First Technology & Best Quality Product Line Up 구분 P/N Function PKG 비고 Linear DC/DC Buck DW8501 DW8502 DW8505A DW8506 DW8520 DW8522 DW8525 DW8527 TO-252 SOT-223
Li-ion/Li Polymer Battery Charger. Features
General Description The is a highly-integrated battery charger for single-cell Li-ion or Li-polymer batteries capable of operating with an input voltage reached 2.5V. It is a complete charger device designed
0.9V Boost Driver PR4403 for White LEDs in Solar Lamps
0.9 Boost Driver for White LEDs in Solar Lamps The is a single cell step-up converter for white LEDs operating from a single rechargeable cell of 1.2 supply voltage down to less than 0.9. An adjustable
Constant Voltage and Constant Current Controller for Adaptors and Battery Chargers
TECHNICAL DATA Constant Voltage and Constant Current Controller for Adaptors and Battery Chargers IK3051 Description IK3051 is a highly integrated solution for SMPS applications requiring constant voltage
LDS8720. 184 WLED Matrix Driver with Boost Converter FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
184 WLED Matrix Driver with Boost Converter FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier) 250 mv
Evaluating AC Current Sensor Options for Power Delivery Systems
Evaluating AC Current Sensor Options for Power Delivery Systems State-of-the-art isolated ac current sensors based on CMOS technology can increase efficiency, performance and reliability compared to legacy
MIC33050. General Description. Features. Applications. Typical Application. 4MHz Internal Inductor PWM Buck Regulator with HyperLight Load
4MHz Internal Inductor PWM Buck Regulator with HyperLight Load General Description The Micrel is a high-efficiency 600mA PWM synchronous buck (step-down) regulator with internal inductor featuring HyperLight
OPENUPS. 6-30V Intelligent Uninterruptible Power Supply. Installation Guide. Version 1.0f P/N OPENUPS-06
OPENUPS 6-30V Intelligent Uninterruptible Power Supply Installation Guide Version 1.0f P/N OPENUPS-06 Before you start Please take a moment and read this manual before you install the OPENUPS. Often times,
Ametek Prestolite Power AC power / Charger / Battery terms
Ametek Prestolite Power AC power / Charger / Battery terms Basic Values: Voltage: The potential difference at the battery (DC) or at the charger input (AC) measured in Volts. Current: The rate of flow
MAX1501 Highly Integrated, Linear Battery Charger with Thermal Regulation for Portable Applications
General Description The MAX1501 intelligent, constant-current, constantvoltage (CCCV), temperature-regulated battery charger charges a single lithium-ion (Li+) cell or three-cell NiMH/NiCd batteries. The
FEATURES DESCRIPTIO APPLICATIO S. LTC4054-4.2/LTC4054X-4.2 Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT
FEATURES Programmable Charge Current Up to 8mA No MOSFET, Sense Resistor or Blocking Diode Required Complete Linear Charger in ThinSOT TM Package for Single Cell Lithium-Ion Batteries Constant-Current/Constant-Voltage
Hybrid Electrical Energy Storage Systems
Hybrid Electrical Energy Storage Systems Naehyuck Chang and Massoud Pedram Seoul National University University of Southern California Outline Electrical energy storage systems Energy storage elements
7-41 POWER FACTOR CORRECTION
POWER FTOR CORRECTION INTRODUCTION Modern electronic equipment can create noise that will cause problems with other equipment on the same supply system. To reduce system disturbances it is therefore essential
PCB Layout Considerations for Non-Isolated Switching Power Supplies
June 2012 PCB Layout Considerations for Non-Isolated Switching Power Supplies Henry J. Zhang Introduction The best news when you power up a prototype supply board for the very first time is when it not
Fox-2 MPPT Unit Testing
P13271 Fox-2 MPPT Unit Testing Final Engineering Specifications Testing Author: Brenton Salmi P13271 Team Members: Brenton Salmi, Bryce Salmi, Ian MacKenzie, Daniel Corriero 5/10/2013 This test document
Datasheet. 2A 380KHZ 20V PWM Buck DC/DC Converter. Features
General Description Features The is a 380 KHz fixed frequency monolithic step down switch mode regulator with a built in internal Power MOSFET. It achieves 2A continuous output current over a wide input
STOD2540. PMOLED display power supply. Features. Application. Description
PMOLED display power supply Features Inductor switches boost controller PFM mode control High efficiency over wide range of load (1 ma to 40 ma) Integrated load disconnect switch Over voltage protection
APPLICATIONS. Battery chargers. DC motor control. Level translating QUANTITY PER REEL. ZXCT1009FTA 7 8mm 3,000 units 109 SOT23
HIGH-SIDE CURRENT MONITOR DESCRIPTION The is a high side current sense monitor. Using this device eliminates the need to disrupt the ground plane when sensing a load current. It takes a high side voltage
Li-Ion Myth-Buster. Poking holes into some common beliefs about Li-Ion cells and Li-Ion BMSs. Davide Andrea Elithion - Electronics for Lithium Ion
Li-Ion Myth-Buster Poking holes into some common beliefs about Li-Ion cells and Li-Ion BMSs. Davide Andrea Elithion - Electronics for Lithium Ion Battery Power Conference 2010, 1, EXTRA! EXTRA! As heard
TS321 Low Power Single Operational Amplifier
SOT-25 Pin Definition: 1. Input + 2. Ground 3. Input - 4. Output 5. Vcc General Description The TS321 brings performance and economy to low power systems. With high unity gain frequency and a guaranteed
QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries General Description The ICS1700A is a CMOS device designed for the intelligent charge control of either nickel-cadmium
High Efficiency Battery Charger using Power Components [1]
![High Efficiency Battery Charger using Power Components [1]](/thumbs/40/21622985.jpg "High Efficiency Battery Charger using Power Components [1]")
application note TPB:101 High Efficiency Battery Charger using Power Components [1] Marco Panizza Senior Applications Engineer July 2006 Contents Page Introduction 1 A Unique Converter 1 Control Scheme
1.5A ASYNCHRONOUS DC-DC BUCK CONV
General Description The is a 1.4MHz fixed frequency, current mode, PWM buck (step-down) DC-DC converter, capable of driving a 1.5A load with high efficiency, excellent line and load regulation. The device
VP223 USB Type-C DFP CC Controller with Universal Battery Charging
Product Preliminary VP223 USB Type-C DFP CC Controller with Universal Battery Charging Mar. 11, 2015 VIA Labs, Inc. www.via-labs.com 7F, 529-1, Zhongzheng Rd., Xindian District, New Taipei City 231 Taiwan
Using voltage regulator to convert 5-12V range to 3.3V. Huan Lin
Using voltage regulator to convert 5-12V range to 3.3V Huan Lin 4/2/2010 1 Table of Contents 1. Introduction... Error! Bookmark not defined. 2. Objective... Error! Bookmark not defined. 3. Implementation...
National Semiconductor Power Products - Seminar 3 (LED Lighting)
National Semiconductor Power Products - Seminar 3 (LED Lighting) Dr. Iain Mosely Converter Technology Ltd. Slide 1 Overview Background on LEDs Power Electronics for Driving LEDs LED Driver Specific Solutions
Creating a Usable Power Supply from a Solar Panel
Creating a Usable Power Supply from a Solar Panel An exploration in DC- DC converters By Kathleen Ellis Advised by Dr. Derin Sherman Department of Physics, Cornell College November 21, 2012 Introduction
Loc-1Tx/Loc-5Tx/Loc-10Tx Data Sheet V3.3
Typical Applications Typical Applications Construction Transmitter Assembly Pipe & cable locator transmitter Transmitting active signals for the location of buried pipes and cables High impact ABS Weight
Development of High Frequency Link Direct DC to AC Converters for Solid Oxide Fuel Cells (SOFC)
Development of High Frequency Link Direct DC to AC Converters for Solid Oxide Fuel Cells (SOFC) Dr. Prasad Enjeti Power Electronics Laboratory Department of Electrical Engineering College Station, TX -
UNISONIC TECHNOLOGIES CO., LTD
UPS61 UNISONIC TECHNOLOGIES CO., LTD HIGH PERFORMANCE CURRENT MODE POWER SWITCH DESCRIPTION The UTC UPS61 is designed to provide several special enhancements to satisfy the needs, for example, Power-Saving
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 994 THREE CHANNEL LED BALLASTER WITH PWM LT3003 DESCRIPTION
LT00 DESCRIPTION Demonstration circuit features the LT00 three channel LED ballaster with in a 0-lead MSOP thermally enhanced MSE package. The demonstration circuit is designed to ballast three channels
NC2000 Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
NC2000 Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries General Description The NC2000 is a device designed to intelligent charge either nickel-cadmium (NiCad) or nickel-metal hydride
Torfino Enterprises, Inc.
Torfino Enterprises, Inc. An independent study of commercially available 9 volt rechargeable battery technology for implementation and use with the ICE LIGHT & METAL-TEC 1400 Product line Written By: Nicholas
Fundamentals of Photovoltaic solar technology For Battery Powered applications
Fundamentals of Photovoltaic solar technology For Battery Powered applications Solar is a natural energy source for many battery powered applications. With energy harvested from the sun, the size of batteries
Design of an Auxiliary Power Distribution Network for an Electric Vehicle
Design of an Auxiliary Power Distribution Network for an Electric Vehicle William Chen, Simon Round and Richard Duke Department of Electrical & Computer Engineering University of Canterbury, Christchurch,
DC Electronic Loads 8500 series
Data Sheet DC Electronic Loads 8500 series 2400W 600 W - 1200 W 300 W Versatile & Economical DC Electronic Loads The 8500 series Programmable DC Electronic Loads can be used for testing and evaluating
Together, we work as a team. www.eurotronix.com
AC DC Devices EasyPowerTM MP150 MP155 MP156 MP157 MP100 MP100 MP100L MP103 MP103 MP100L Product Portfolio 1W to 400W AC Input EMI Filter Output + LLC + SR Controller MP6922 MP44022A MP44011 AC Input EMI
Push-Pull FET Driver with Integrated Oscillator and Clock Output
19-3662; Rev 1; 5/7 Push-Pull FET Driver with Integrated Oscillator General Description The is a +4.5V to +15V push-pull, current-fed topology driver subsystem with an integrated oscillator for use in
SOLAR ENERGY HARVESTING
SOLAR ENERGY HARVESTING Low Power in a Compact Footprint By Jeff Gruetter Energy harvesting is by no means a new idea. The first hydroelectric plant which combined water and gravity to drive electricity
AN-8019 Reliable USB Modem Design Using the Combination of an Integrated Load Switch and a Buck Converter
www.fairchildsemi.com AN-8019 Reliable USB Modem Design Using the Combination of an Integrated Load Switch and a Buck Converter Introduction In the portable electronics market, a wireless network allows
Chapter 20 Quasi-Resonant Converters
Chapter 0 Quasi-Resonant Converters Introduction 0.1 The zero-current-switching quasi-resonant switch cell 0.1.1 Waveforms of the half-wave ZCS quasi-resonant switch cell 0.1. The average terminal waveforms
PAM2804. Pin Assignments. Description. Applications. Features. Typical Applications Circuit 1A STEP-DOWN CONSTANT CURRENT, HIGH EFFICIENCY LED DRIVER
1A STEP-DOWN CONSTANT CURRENT, HIGH EFFICIENCY LED DRIER Description Pin Assignments The is a step-down constant current LED driver. When the input voltage is down to lower than LED forward voltage, then
Selecting IHLP Composite Inductors for Non-Isolated Converters Utilizing Vishay s Application Sheet
VISHAY DALE www.vishay.com Magnetics Selecting IHLP Composite Inductors for Non-Isolated Converters INTRODUCTION This application note will provide information to assist in the specification of IHLP composite
An Efficient AC/DC Converter with Power Factor Correction
An Efficient AC/DC Converter with Power Factor Correction Suja C Rajappan 1, K. Sarabose 2, Neetha John 3 1,3 PG Scholar, Sri Shakthi Institute of Engineering & Technology, L&T Bypass Road, Coimbatore-62,
TYPICAL APPLICATION CIRCUIT. ORDER INFORMATION SOP-EP 8 pin A703EFT (Lead Free) A703EGT (Green)
www.addmtek.com 2 CHANNELS 150mA HIGH VOLTAGE ADJUSTABLE CURRENT REGULATOR DESCRIPTION A703 is a high voltage, adjustable constant current driver for LED applications. Two regulated current ports are designed
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS
MC34063A MC34063E DC-DC CONVERTER CONTROL CIRCUITS OUTPUT SWITCH CURRENT IN EXCESS OF 1.5A 2% REFERENCE ACCURACY LOW QUIESCENT CURRENT: 2.5mA (TYP.) OPERATING FROM 3V TO 40V FREQUENCY OPERATION TO 100KHz
POWER FORUM BOLOGNA 27-10-2011
POWER FORUM BOLOGNA 27-10-2011 CONVERSIONE DI POTENZA - ANALOGICO O DIGITALE? QUESTO È IL DILEMMA! Massimo Gavioli Senior Field Application Engineer SIMPLY SMARTER History Intersil: The 1 st company in
Understanding Delta Conversion Online "Power Regulation" - Part 2
Application Note #40 Understanding Delta Conversion Online "Power Regulation" - Part 2 Introduction This application note is the second in a series on delta conversion theory of operation. For complete
How To Make A Two Series Cell Battery Pack Supervisor Module
Features Complete and compact lithium-ion pack supervisor Provides overvoltage, undervoltage, and overcurrent protection for two series Li-Ion cells Combines bq2058t with charge/discharge control FETs
Wireless Precision Temperature Sensor Powers Itself, Forms Own Network, Enabling Easy Deployment in Industrial Environments
Wireless Precision Temperature Sensor Powers Itself, Forms Own Network, Enabling Easy Deployment in Industrial Environments Kris Lokere While the Internet connects people via a worldwide computer network,
PowerGem Pro Uninterruptible Power Supply
Uninterruptible Power Supply User-friendly Intelligent Ultra reliable Range The Most Intelligent On-Line Double Conversion Power Protection System The range achieves higher reliability and greater immunity
L6924D. Battery charger system with integrated power switch for Li-Ion/Li-Polymer. Features. Applications
Battery charger system with integrated power switch for Li-Ion/Li-Polymer Features Fully integrated solution, with a power MOSFET, reverse blocking diode, sense resistor, and thermal protection Ideal for
ULRASONIC GENERATOR POWER CIRCUITRY. Will it fit on PC board
ULRASONIC GENERATOR POWER CIRCUITRY Will it fit on PC board MAJOR COMPONENTS HIGH POWER FACTOR RECTIFIER RECTIFIES POWER LINE RAIL SUPPLY SETS VOLTAGE AMPLITUDE INVERTER INVERTS RAIL VOLTAGE FILTER FILTERS
Solar Energy Conversion using MIAC. by Tharowat Mohamed Ali, May 2011
Solar Energy Conversion using MIAC by Tharowat Mohamed Ali, May 2011 Abstract This work introduces an approach to the design of a boost converter for a photovoltaic (PV) system using the MIAC. The converter
Battery Management Guide
Battery Management Guide ti.com/battery 2015 Battery Management Guide Introduction and Contents Texas Instruments (TI) offers a complete battery management portfolio with a full line of high-performance
Introduction to Wireless Power
Introduction to Wireless Power Wireless power basic concept Wireless power why? Convenience end-users can charge multiple devices (camera, phone, tablet, headset, other accessories) on a common charging
Application Report SLVA057
Application Report March 1999 Mixed Signal Products SLVA057 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product
LTC4000 High Voltage High Current Controller for Battery Charging and Power Management. Applications. Typical Application
Features n Complete High Performance Battery Charger When Paired with a DC/DC Converter n Wide Input and Output Voltage Range: 3V to 60V n Input Ideal Diode for Low Loss Reverse Blocking and Load Sharing
PAM2842. Pin Assignments. Description. Features. Applications. A Product Line of. Diodes Incorporated HIGH POWER LED DRIVER PAM2842
HIGH POWER LED DRIVER Description Pin Assignments The is a high power LED driver, capable of driving up to 10 high power LEDs in series. The supports buck, boost and sepic topology. The features over current
Cree PV Inverter Tops 1kW/kg with All-SiC Design
Cree PV Inverter Tops 1kW/kg with All-SiC Design Alejandro Esquivel September, 2014 Presentation Outline 1. Meeting an Industry Need a) 1kW/Kg b) No electrolytic capacitors in DC link 2. 50 + kw SiC based
Micropower, Step-Up/Step-Down SW Regulator; Adjustable and Fixed 3.3 V, 5 V, 12 V ADP1111
a FEATURES Operates from 2 V to 30 V Input Voltage Range 72 khz Frequency Operation Utilizes Surface Mount Inductors Very Few External Components Required Operates in Step-Up/Step-Down or Inverting Mode
PACKAGE OUTLINE DALLAS DS2434 DS2434 GND. PR 35 PACKAGE See Mech. Drawings Section
PRELIMINARY DS2434 Battery Identification Chip FEATURES Provides unique ID number to battery packs PACKAGE OUTLINE Eliminates thermistors by sensing battery temperature on chip DALLAS DS2434 1 2 3 256
How To Power A Power Control Microprocessor (Power Control) Microprocessor 2 (Power) (Power Power) (Control) (Repower) Microcontroller (Power/Reflow) (Mini) (Microprocessor) (Wired) (Wire
PTC NTC for Surface Mounting Application What is a Thermistor? Thermally Sensitive Resistor Thermistor Positive Temperature Coefficient PTC Negative Temperature Coefficient NTC Characteristics of Thermistors
UPS Applications and VRLA Battery Sizing
TECHNICAL BULLETIN 41-7334 UPS Applications and VRLA Battery Sizing 41-7334/0213/CD www.cdtechno.com The uninterruptable power system (UPS) is used to protect critical equipment and processes from the
Low Dropout AIC1084 AIC1085 AIC1086 AIC1117 AIC1117A. Quick Reference - Power Conversion P.1... Quick Reference - Power Manipulation P.
2016 Quick Reference - Power Conversion INDEX Linear Regulator/ Reference p3 Quick Reference Quick Reference - Power Conversion P.1 Quick Reference - Power Manipulation P.2 Low Dropout AIC1084 AIC1085
48V eco-hybrid Systems
48V eco-hybrid Systems Jean-Luc MATE Vice President Continental Engineering Services France President Automotech cluster www.continental-corporation.com Division Naming European Conference on Nanoelectronics
Bi-Directional Inverter and Energy Storage System. Texas Instruments Analog Design Contest
Bi-Directional Inverter and Energy Storage System Submitted to fulfill the requirements of: Texas Instruments Analog Design Contest by Derik Trowler and Bret Whitaker May 2008 University of Arkansas College
Solar Powered LED Street Lighting
Solar Powered LED Street Lighting Solar Powered LED Street Lighting Courtesy of BetaLighting 2 Agenda Trends for solar powered LED street lighting Regulating voltage out of a solar panel Application overview
1ED Compact A new high performance, cost efficient, high voltage gate driver IC family
1ED Compact A new high performance, cost efficient, high voltage gate driver IC family Heiko Rettinger, Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany, heiko.rettinger@infineon.com
MC33064DM 5 UNDERVOLTAGE SENSING CIRCUIT
Order this document by MC3464/D The MC3464 is an undervoltage sensing circuit specifically designed for use as a reset controller in microprocessor-based systems. It offers the designer an economical solution
DS1307ZN. 64 x 8 Serial Real-Time Clock
DS137 64 x 8 Serial Real-Time Clock www.maxim-ic.com FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid
Design and Construction of Variable DC Source for Laboratory Using Solar Energy
International Journal of Electronics and Computer Science Engineering 228 Available Online at www.ijecse.org ISSN- 2277-1956 Design and Construction of Variable DC Source for Laboratory Using Solar Energy