Application Notes SL1000/SL500 VPN with Cisco PIX 501

Transcription

1 Application Notes SL1000/SL500 VPN with Cisco PIX 501 Version 1.0 Copyright 2006, ASUSTek Computer, Inc. i

2 Revision History Version Author Date Status 1.0 Martin Su 2006/5/4 Initial draft Copyright 2006, ASUSTek Computer, Inc. ii

3 Table of Contents Revision History...ii Table of Contents...iii List of Figures...iii 1 Introduction Network Setup Setup Description Setup CISCO PIX Firewall Setup IP address of LAN interface Setup IP address of WAN interface Setup Routing Table Setup SL1000/SL500 system Setup IP address of LAN interface Setup IP address of WAN interface Setup Routing Table Establish VPN Tunnel using Automatic Keying Configure VPN Policy on PIX Configure VPN Policy on SL1000/SL Verify VPN Tunnel Establishment...7 List of Figures Figure 2.1 Network Connections...1 Figure 2.2 Setup LAN port IP address on the PIX firewall...1 Figure 2.3 Setup WAN port IP address on the PIX firewall...1 Figure 2.4 Setup a default route to the PIX firewall...2 Figure 2.5 Setup LAN port IP address on the SL1000/SL Figure 2.6 Setup IP address of WAN interface on the SL1000/SL Figure 2.7 Verify WAN interface configurations on the SL1000/SL Figure 2.8 Setup a default route to the SL1000/SL Figure 3.1 Setup VPN policy on the PIX firewall...4 Figure 3.2 Verify VPN configurations on the PIX firewall...5 Figure 3.3 Configure VPN policy on the SL1000/SL Figure 3.4 Verify VPN configurations on the SL1000/SL Figure 3.5 Verify VPN tunnel establishment on the PIX firewall...8 Figure 3.6 Verify the VPN tunnel establishment on the SL1000/SL Copyright 2006, ASUSTek Computer, Inc. iii

4 1 Introduction This application note details the steps for creating an IPSec VPN tunnel between an ASUS Internet Security Router and a CISCO PIX Firewall device. It is assumed that both devices have static IP address on the WAN interface, and a default route configured. All settings and screen dumps contained in this document are taken from a CISCO PIX 501 device running firmware PIX Firewall Version 6.3(4), and an ASUS SL1000/SL500 running firmware A Network Setup This section describes how to setup the network to carry out the SL1000/SL500 and CISCO PIX 501 Network Configuration as illustrated in Figure 2.1. Cross Ethernet Cable WAN: WAN: LAN: Internet Security Router LAN: CISCO PIX501 PC2: PC1: Figure 2.1 Network Connections 2.1 Setup Description PC1 and PC2 are hosts in protected networks running Windows NT/98/2000/XP or Redhat Linux. Both SL1000/SL500 and PIX Firewall will protect their traffic from external network. NAT is not required for traffic between the two intranets, which can be transmitted using a VPN tunnel over the public Internet (in this setup example, a direct connection between two WAN interfaces serves as public network). However, NAT is required for connections to public Internet. 2.2 Setup CISCO PIX Firewall Setup IP address of LAN interface pixfirewall# configure terminal pixfirewall(config)# ip address inside Figure 2.2 Setup LAN port IP address on the PIX firewall Setup IP address of WAN interface pixfirewall(config)# interface ethernet0 auto pixfirewall(config)# ip address outside Figure 2.3 Setup WAN port IP address on the PIX firewall Copyright 2006, ASUSTek Computer, Inc. Page 1

5 2.2.3 Setup Routing Table pixfirewall(config)# route outside Figure 2.4 Setup a default route to the PIX firewall 2.3 Setup SL1000/SL500 system Setup IP address of LAN interface Figure 2.5 Setup LAN port IP address on the SL1000/SL Setup IP address of WAN interface Figure 2.6 Setup IP address of WAN interface on the SL1000/SL500 Copyright 2006, ASUSTek Computer, Inc. Page 2

6 Figure 2.7 Verify WAN interface configurations on the SL1000/SL Setup Routing Table Figure 2.8 Setup a default route to the SL1000/SL500 3 Establish VPN Tunnel using Automatic Keying 3.1 Configure VPN Policy on PIX 501 Step: 1 Configure access list rule and VPN policy pixfirewall(config)# access-list SL1000 permit ip pixfirewall(config)# nat (inside) 0 access-list SL1000 pixfirewall(config)# sysopt connection permit-ipsec pixfirewall(config)# crypto ipsec transform-set set1 esp-3des esp-sha-hmac pixfirewall(config)# crypto ipsec security-association lifetime seconds 3600 pixfirewall(config)# crypto map tosl ipsec-isakmp pixfirewall(config)# crypto map tosl match address SL1000 pixfirewall(config)# crypto map tosl set peer pixfirewall(config)# crypto map tosl set transform-set set1 pixfirewall(config)# crypto map tosl1000 interface outside pixfirewall(config)# isakmp enable outside pixfirewall(config)# isakmp key cwtest address netmask pixfirewall(config)# isakmp identity address pixfirewall(config)# isakmp policy 20 authentication pre-share pixfirewall(config)# isakmp policy 20 encryption 3des pixfirewall(config)# isakmp policy 20 hash sha pixfirewall(config)# isakmp policy 20 group 2 pixfirewall(config)# isakmp policy 20 lifetime 3600 Copyright 2006, ASUSTek Computer, Inc. Page 3

7 Figure 3.1 Setup VPN policy on the PIX firewall Step 2: Verify Configurations pix-firewall# show config : Saved : Written by enable_15 at 14:22: UTC Thu May PIX Version 6.3(4) interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname pix-firewall domain-name asus.com.tw fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h fixup protocol h323 ras fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names access-list SL1000 permit ip pager lines 24 mtu outside 1500 mtu inside 1500 ip address outside ip address inside ip audit info action alarm ip audit attack action alarm pdm location inside pdm history enable arp timeout global (outside) 1 interface nat (inside) 0 access-list SL1000 route outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute Copyright 2006, ASUSTek Computer, Inc. Page 4

8 aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ max-failed-attempts 3 aaa-server TACACS+ deadtime 10 aaa-server RADIUS protocol radius aaa-server RADIUS max-failed-attempts 3 aaa-server RADIUS deadtime 10 aaa-server LOCAL protocol local http server enable http inside no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable sysopt connection permit-ipsec crypto ipsec transform-set set1 esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 3600 crypto map tosl ipsec-isakmp crypto map tosl match address SL1000 crypto map tosl set peer crypto map tosl set transform-set set1 crypto map tosl1000 interface outside isakmp enable outside isakmp key ******** address netmask isakmp identity address isakmp policy 20 authentication pre-share isakmp policy 20 encryption 3des isakmp policy 20 hash sha isakmp policy 20 group 2 isakmp policy 20 lifetime 3600 telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 80 Cryptochecksum: c43a8ad0a01202a9686af3ed4 Figure 3.2 Verify VPN configurations on the PIX firewall Copyright 2006, ASUSTek Computer, Inc. Page 5

9 3.2 Configure VPN Policy on SL1000/SL500 Before configuring VPN, you need to enable VPN service in System Management->System Service first. Figure 3.3 Configure VPN policy on the SL1000/SL500 Figure 3.4 Verify VPN configurations on the SL1000/SL500 Copyright 2006, ASUSTek Computer, Inc. Page 6

10 3.3 Verify VPN Tunnel Establishment pix-firewall# show crypto isakmp sa Total : 1 Embryonic : 0 dst src state pending created QM_IDLE 0 1 pix-firewall# show crypto ipsec sa interface: outside Crypto map tag: tosl1000, local addr local ident (addr/mask/prot/port): ( / /0/0) remote ident (addr/mask/prot/port): ( / /0/0) current_peer: :500 PERMIT, flags={origin_is_acl,} #pkts encaps: 12, #pkts encrypt: 12, #pkts digest 12 #pkts decaps: 12, #pkts decrypt: 12, #pkts verify 12 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0 #send errors 0, #recv errors 0 local crypto endpt.: , remote crypto endpt.: path mtu 1500, ipsec overhead 56, media mtu 1500 current outbound spi: 5f4579cf inbound esp sas: spi: 0x991686ee( ) transform: esp-3des esp-sha-hmac, in use settings ={Tunnel, } slot: 0, conn id: 1, crypto map: tosl1000 sa timing: remaining key lifetime (k/sec): (74998/3472) IV size: 8 bytes replay detection support: Y inbound ah sas: inbound pcp sas: outbound esp sas: spi: 0x5f4579cf( ) transform: esp-3des esp-sha-hmac, in use settings ={Tunnel, } slot: 0, conn id: 2, crypto map: tosl1000 Copyright 2006, ASUSTek Computer, Inc. Page 7

11 sa timing: remaining key lifetime (k/sec): (74999/3463) IV size: 8 bytes replay detection support: Y outbound ah sas: outbound pcp sas: Figure 3.5 Verify VPN tunnel establishment on the PIX firewall Figure 3.6 Verify the VPN tunnel establishment on the SL1000/SL500 Copyright 2006, ASUSTek Computer, Inc. Page 8