Replacement Procedure for E4982A LCR Meter REPLACEMENT PROCEDURE FOR E4982A LCR METER

Transcription

1 Replacement Procedure for E498A LCR Meter REPLACEMENT PROCEDURE FOR E498A LCR METER

2 REVISION HISTORY REVISION 1 DESCRIPTION Initial Release DATE May 01 REVISION HISTORY

3 TOOL AND FIXTURE LIST PART NO. DESCRIPTION T-10 Torque driver T-10 Torque driver T-15 Torque driver T-0 Torque driver 5/8 Box Wrench 9/16 Box Wrench 5.5mm Box Torque driver 1.7mm Allen Key 5/16 Open End Wrench TORQUE VALUE / SET UP 4.4 lbin 9 lbin 14 lbin 1 lbin 30.4 inlb 30.4 inlb 6 lbin lbin 9.5 lbin TOOL AND FIXTURE LIST

4 Replacement Procedure Menu Click the hyperlink below for any choice of dis-assembly procedure: 1. LCD. Hard Disk 3. CPU Module (E ) 4. Display Board (E ) 5. Source Module (E ) 6011) & Receiver Module (E ) 6. Analog Board (E ) 7. Test Head REPLACEMENT PROCEDURE MENU

5 LCD Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. LCD - DIS-ASSEMBLY PROCEDURE

6 (Top Trim) & (Side Trim) (7ea) 3a 3b Slowly pull/remove Front Subassembly from Chassis Disconnect flat cable of Front Panel Assembly from CPU Module LCD - LCD DIS-ASSEMBLY (1)

7 Disconnect cable 3 Open cable clamp Front Sub- assembly from Chassis LCD - LCD DIS-ASSEMBLY ()

8 1 E Open Wire clamp 1 LCD - LCD DIS-ASSEMBLY (3)

9 (6ea) 3 E Disconnect the cable 1 3 LCD - LCD DIS-ASSEMBLY (4)

10 , pcs E Cut cable tie, LCD - LCD DIS-ASSEMBLY (5) b10 A

11 Note: Check Cable Orientation Disconnect cables 1 Open cable clamp 1 LCD - LCD DIS-ASSEMBLY (6) b0 A

12 , 4pcs 1 LCD 1 LCD - LCD DIS-ASSEMBLY (7) b30 A

13 Hard Disk Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. HDD - DIS-ASSEMBLY PROCEDURE b50 A

14 4 E HANDLE ASSEMBLY , 4pcs , 4pcs E E , 4pcs HDD - HDD DIS-ASSEMBLY (1) b60 A

15 Cut all cable tie (4 ea) 1 Cut cable tie HDD - HDD DIS-ASSEMBLY () b70 A

16 Slowly Slide out the Sub-Assembly HDD from chassis ea 1 HDD - HDD DIS-ASSEMBLY (3)

17 Disconnect E Disconnect Cut Cable Tie HDD - HDD DIS-ASSEMBLY (4)

18 ea 3 HDD E HDD - HDD DIS-ASSEMBLY (5) c10 A

19 CPU Module (E ) Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. CPU MODULE - DIS-ASSEMBLY PROCEDURE c30 A

20 4 E HANDLE ASSEMBLY , 4pcs , 4pcs E E , 4pcs CPU MODULE - CPU MODULE DIS-ASSEMBLY (1) b60 A

21 Cut all cable tie (4 ea) 1 Cut cable tie CPU MODULE - CPU MODULE DIS-ASSEMBLY () b70 A

22 1 Disconnect E Open CPU MODULE - CPU MODULE DIS-ASSEMBLY (3) c60 A

23 DISCONNECT All cables on CPU Module CPU MODULE - CPU MODULE DIS-ASSEMBLY (4) c70 A

24 Slowly Slide out the Sub-Assembly HDD from chassis ea 1 CPU MODULE - CPU MODULE DIS-ASSEMBLY (5)

25 3 CPU Board E , 3pcs , 4pcs CPU MODULE - CPU MODULE DIS-ASSEMBLY (6)

26 Display Board (E ) Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. DISPLAY BOARD - DIS-ASSEMBLY PROCEDURE

27 (Top Trim) & (Side Trim) (7ea) 3a 3b Slowly pull/remove Front Subassembly from Chassis Disconnect flat cable of Front Panel Assembly from CPU Module DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (1)

28 Disconnect cable 3 Open cable clamp Front Sub- assembly from Chassis DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY ()

29 4 DISCONNECT E DISCONNECT E , pcs , pcs , pcs E DISPLAY BOARD - DISPLAY BOARD DIS-ASSEMBLY (3)

30 Source Module (E ) Receiver Module (E ) Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. SOURCE/RECIEVER MODULE - DIS-ASSEMBLY PROCEDURE

31 (Top Trim) & (Side Trim) (7ea) 3a 3b Slowly pull/remove Front Subassembly from Chassis Disconnect flat cable of Front Panel Assembly from CPU Module SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY (1)

32 Disconnect cable 3 Open cable clamp Front Subassembly from Chassis SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY ()

33 9.5 in lb (Semi rigid Cable) 1)5/16 Open End Wrench )Minor Male c/w C Socket E E SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY (3)

34 (ea) 1 1 SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY (4)

35 E Source Board 1 Source Board (E ) 1 SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY (5)

36 (ea) 1 Receiver Board (E ) 1 SOURCE/RECIEVER MODULE - SOURCE/RECIEVER MODULE DIS-ASSEMBLY (6)

37 Analog Board (E ) 66610) Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. ANALOG BOARD - DIS-ASSEMBLY PROCEDURE

38 (Top Trim) & (Side Trim) (7ea) 3a 3b Slowly pull/remove Front Subassembly from Chassis Disconnect flat cable of Front Panel Assembly from CPU Module ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (1)

39 Disconnect cable 3 Open cable clamp Front Sub- assembly from Chassis ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY ()

40 4 DISCONNECT E DISCONNECT E , pcs , pcs , pcs E ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (3)

41 9.5 in lb (Semi rigid Cable) 1)5/16 Open End Wrench )Minor Male c/w C Socket E E ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (4)

42 (ea) 1 1 ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (5)

43 E Source Board 1 Source Board (E ) 1 ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (6)

44 4 E (3ea) (3ea) (7ea) Use T Protective Jig 9/16 Torque box 30.4 inlb ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (8)

45 1 Disconnect the Fan Cable ( connector) (11ea) ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (9)

46 Disconnect E Disconnect E E ANALOG BOARD - ANALOG BOARD DIS-ASSEMBLY (10)

47 Test Head (E ) Dis-Assembly Procedure Note: 1. Torque value shown in this document is only for reference and only used during assembly. TEST HEAD DIS-ASSEMBLY PROCEDURE

48 TEST HEAD DIS-ASSEMBLY PROCEDURE (1)

49 the Angle Protector E Qty 1 TEST HEAD DIS-ASSEMBLY PROCEDURE ()

50 the connection from Port 1, Port and RF Out 1 PORT PORT 1 3 RF OUT 1 3 TEST HEAD DIS-ASSEMBLY PROCEDURE (3)

51 5/16 Open End Wrench 9.5 lbin E E Labeled as PORT Labeled as PORT 1 Label as RF OUT 1 TEST HEAD DIS-ASSEMBLY PROCEDURE (4)

52 For Option-00 ONLY cable connection as shown below RF OUT PORT 1 PORT TEST HEAD DIS-ASSEMBLY PROCEDURE (5)

53 For Option-00 ONLY 3 E Qty 3 4 all 3 adapters 9.5 inlb Previous Assy TEST HEAD DIS-ASSEMBLY PROCEDURE (6)