access To read, write, or update information on some storage media, such as a disk.

Transcription

1 GLOSSARY This Glossary includes an alphabetized listing and brief definition of the abbreviations, acronyms, Quantum-specific references, product-specific references, and other technical terms that are used in this manual and that may be unfamiliar to the reader. access To read, write, or update information on some storage media, such as a disk. access time The interval between a system request for data and the time the data is available from the drive. Access time includes the seek time, rotational latency, and servo and command processing overhead. It is usually given as the average time required to access data. See also seek, rotational latency, and overhead. active I/O process An I/O process that is currently in execution (not queued). actuator Also known as the positioner assembly. The internal mechanism that moves the read/write head to the proper track. There are two types of actuators: rotary voice coil and stepper motor. See rotary voice coil and stepper motor. allocation The process of assigning particular areas of the disk to particular files. See also allocation unit. allocation unit Also known as a cluster. A group of sectors on the disk that can be reserved for the use of a particular file. ANSI Abbreviation for American National Standards Institute ASCII Abbreviation for American Standard Code for Information Interchange average seek time The average time required for a read/write head to move between randomly located tracks. backup A copy of data on a separate storage device from the original, to be used if the original is accidentally erased, damaged, or destroyed. bad block A block (usually the size of a sector) that cannot reliably store data because of a media flaw or damaged format markings. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 1

2 Banding A method of variable frequency recording on the media that attempts to keep the bit density constant, regardless of the track radius. Banding greatly increases capacity and data transfer rates. bezel Also known as the faceplate. A plastic panel that extends the face of a drive so that it covers a computer s drive bay opening. The bezel usually contains a drive-activity LED. bit Acronym for binary digit. The smallest unit of information recognized by a computer, a binary digit may have one of two values: 1 or 0. A bit is one of the logic 1 or logic 0 binary settings that make up a byte of data. See also byte. block The smallest discrete unit that a drive s controllers can read or write to in a single operation. By default, a block of data consists of 512 bytes. BPI Abbreviation for bits per inch. A measure of how densely data is packed on a storage medium. buffer An area of RAM used for temporary storage of data that is waiting to be transferred to a device that is not yet ready to receive it. bus The part of a chip, circuit board, or interface that conducts data, typically in parallel fashion. byte The basic unit of computer memory, large enough to hold one character of alphanumeric data. Normally, a byte is composed of eight bits. See also bit. cache RAM used as a buffer between the CPU and a hard disk. Information more likely to be read or changed is placed in the cache, where it can be accessed more quickly to speed up general data flow. See also prefetch. capacity The amount of information that can be stored on a disk drive. The data is stored in bytes, and capacity is usually expressed in megabytes, gigabytes or in data sectors. clean room An environmentally controlled, dust-free facility in which hard disk drives are assembled or serviced. CMOS Acronym for complementary metal oxide semiconductor. A low-power, low-heat, highdensity semiconductor. G 2 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

3 command queue The queue used to store I/O processes. connect The initiator function that selects a target to establish a nexus and to start an I/O process. The connection that results is an initial connection. connection An initial connection or reconnection that can occur only between one initiator and one target. contingent allegiance A condition generated by a CHECK CONDITION or COMMAND TERMINATED status during which execution of all tagged I/O processes (for the associated I_T_X nexus) are suspended until the condition is cleared. A target preserves an I_T_X nexus until it is cleared by a hard or soft reset, an abort message or another command for that I_T_X nexus. While the contingent allegiance condition exists, the target maintains sense data for the initiator. controller The circuitry that manages a device s physical data access operations, such as moving read/write heads and erasing tracks and sectors. controller card An adapter that holds the control electronics for a device, usually installed in a computer. CPU Abbreviation for central processing unit. The microprocessor chip that processes information and coordinates all computer functions. CRC Abbreviation for cyclic redundancy check. Another name for the 16-bit error detection code (EDC) that is recorded in each data sector. It is used to determine whether parts of a data string are missing or incorrect. cylinder An imaginary structure that is one track, on each of the disks, that is located at a given head position. The number of cylinders multiplied by the number of heads equals the number of tracks in the drive. dedicated servo A disk surface separate from a data surface that contains only timing and head positioning information. Generally considered to be obsolete technology. defect management A method that is implemented to ensure long-term data integrity. This is accomplished by scanning the disk drives at the factory for defective sectors, which are then reallocated prior to shipment. During regular use, the drive continues to scan and compensate for any new defective sectors on the disk. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 3

4 differential termination One of two methods for terminating the SCSI bus, characterized by a two-line signal: a (+) signal and a ( ) signal. Used to improve noise resistance when long bus cables are required. See also single-ended termination. disk Any circular-shaped data storage media that stores data on the flat surface of the platter. The most common disk type is the magnetic disk, which stores data as magnetic patterns in a metal or metal-oxide coating. disk controller The chip or complete circuit that translates computer data and commands into a form suitable for use by the disk drive. DMA Abbreviation for direct memory access. A process by which data moves directly between a disk drive or other device and system memory without passing through the CPU. This allows the system to continue processing other tasks while the new data is being retrieved. drive Typically the short form of disk drive but can refer to a tape drive. drive electronics See electronics module drive geometry The functional dimensions of a drive: number of heads, cylinders, and sectors per track. See also low-level formatting. ECC Abbreviation for error correction code. An error detection and correction algorithm developed by Reed and Solomon for the verification and correction of stored data. EDC Abbreviation for error detection code. An end-to-end cyclic redundancy code that is used to protect data from errors that may be introduced by the connecting busses, the disk controller chip, the data cache, or the SCSI interface in a disk drive. See also, CRC. electronics module The printed circuit board containing the drive electronics. embedded servo A head positioning technique wherein composite digital and quadrature analog signals are placed in radial spokes on each track, on each disk surface. The signals are read and decoded and used to locate data sectors on the tracks and to center the read/write heads on the tracks. See also, servo spoke data. encoding Any technique in which a data format is changed to achieve a particular purpose such as error detection and correction or data compression. G 4 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

5 EPROM Acronym for erasable programmable read-only memory. Integrated circuit memory chip that can store programs and data in a nonvolatile state. These devices can be erased by ultraviolet light and reused. extended contingent allegiance A condition generated by a target and announced with a INITIATE RECOVERY message. The mode is used when multi-step extended error recovery procedures are required to prevent interference as from other initiators in a multi-initiator system. See also contingent allegiance false Refers to the logical-zero (or negated ) state of a binary number. See also, signal negation. fast SCSI The SCSI protocol that governs fast synchronous transfer. See also Synchronous Transfer. FCI Abbreviation for flux changes per inch. Used to describe the storage density on a magnetic surface. See also flux density. field A logically related group of one or more physically contiguous bits. file server A computer that provides network stations with controlled access to shared resources. firmware The program instructions and data stored in EPROM (read-only memory) for use by a processor. flux density The number of magnetic field patterns that can be stored in a given length of disk surface. The number is usually stated as flux changes per inch (FCI), with typical values in the thousands. flying height The distance between the read/write head and the disk surface. Smaller flying heights permit more dense data storage but require more precise mechanical design. form factor The platter size of a device as defined by industry standard. Popular form factors are 1.3- inch, 1.8 inch, 2.5 inch, 3.5 inch, and 5.25 inch. The trend is toward smaller sizes. format The format process writes the initial logical-to-physical mapping on the disk surface. This includes any bad-block slipping or revectoring. This information must exist on a disk before it can store any user data. Formatting erases any previously stored data. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 5

6 formatted capacity The amount of room left to store data on a disk after the required space has been used to write sector headers, boundary definitions, and timing information generated by a format operation. full height Term used to describe a disk that occupies the vertical space (3.250 inches) of a full sized 5.25-inch drive. See also half height, low profile. GB See gigabyte. gigabyte (GB) 1,000,000,000. (10 9) bytes, as for disk capacity. See also megabyte. Glist Abbreviation. When the drive encounters a defective sector during regular use, it adds the address of the sector to the Grown Defect List (Glist). See also Plist. guide rails Plastic or metal strips attached to the sides of a disk drive so that the drive slides easily into place. half height Term used to describe a disk that occupies half the vertical space (1.625 inches) of a full sized 5.25-inch drive. See also full height, low profile. hard disk A storage media that retains data as magnetic patterns on a rigid disk, usually made of an iron oxide or alloy over a magnesium or aluminum platter. Because hard disks spin far more rapidly than floppy disks, and the head flies closer to the disk, hard disks can transfer data much faster and store a great deal more data in the same area. hard error A repeatable error in disk data that persists when the disk is re-read. It usually is caused by a tiny defect in the recording media surface. head assembly The tiny electromagnetic or magneto-resistive element used to write and read back the magnetic patterns of data on the recording media. See also Diamond Head. head disk assembly (HDA) The assembly made up of the spindle motor, spindle, head positioner (actuator), head preamp electronics, and magnetic disk assembly. high-level formatting Formatting performed by the operating system s format program. Among other things, the formatting program creates the root directory and file allocation tables. See also lowlevel formatting, format. G 6 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

7 host adapter The interface between a particular type of computer system bus and the disk drive, usually a plug-in board. An example is the SCSI Controller. interface A hardware or software protocol, contained in the electronics of the disk controller and disk drive, that manages the exchange of data between the drive and the computer. Also refers to the hardware required to connect the controller and drive. I/O process An I/O process consists of an initial connection (nexus) followed by zero or more reconnections, all pertaining to a single command or a group of linked commands. An I/O process normally ends with a BUS FREE phase following a COMMAND COMPLETE or a RELEASE RECOVERY message. jumper An electrical connector, contained in a small plastic enclosure, used to configure or select circuit board features or options. The jumper slips over two pins that protrude from a circuit board or pins of a connector to connect the two pins electrically. Sometimes called a shunt jumper. latency The delay between when the controller arrives on track and starts looking for a specific block of data on a track and when that block rotates around to where it can be accessed by the read/write head. On average, it is half the rotation time. LBA Abbreviation for Logical Block Address. A sequentially-numbered identity of a multibyte block of user data. It does not refer directly to the physical location of the data in a disk drive. logical format The logical drive geometry that appears to the computer system BIOS as defined by the drive tables and stored in CMOS. logical unit A physical or virtual peripheral device addressable through a target. low-level formatting Formatting maps logical blocks to physical blocks so the operating system can access the required areas for generating the file structure. See also high-level formatting, formatting. low profile Drives built to the 3.5-inch form factor but are only 1 inch high. The standard 3.5-inch form factor drives are inches high. See also half height, full height. magneto-resistive A unique characteristic of some metals, which, when combined, yields a variable electrical resistance to varying magnetic fluxes. The resistance varies directly with the strength of the flux, field, not simply to a change in flux as with magneto-inductance. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 7

8 media The magnetic film that is deposited or coated on an aluminum substrate that forms a platter. The media is overcoated with a molecularly-thin lubricating surface to prevent damage to the heads or media during head take off and landing. The media is where the data is stored in the form of magnetic flux or magnetic polarity changes. megabit (Mb) 1,000,000 (10 6 ) bits. megabyte (MB) 1,000,000 (10 6 ) bytes for disk capacity or 2 20 bytes for RAM capacity. See also gigabyte. megahertz (MHz) A measurement of frequency in millions of cycles per second. MHz See megahertz. microprocessor The integrated circuit chip that performs the bulk of data processing and controls the operation of all the parts of the system. A disk drive also contains a microprocessor to handle all the internal functions of the drive and to support the embedded controller. MTBF Abbreviation for mean time before failure. Rates predict the reliability of a product, and is often expressed in power on hours (POH). nanosecond (ns) One billionth of a second ( second or 10-9 second). nexus A relationship between two devices that begins with the establishment of an initial connection and ends with the completion of an I/O process. A nexus relationship is further defined by the letters I (initiator), T (target), L (logical unit), R (target routine), x (either L or R), Q (queue tag), and x_y (either an x or a Q) ORCA Optimized Reordering Command Algorithm. A unique method for executing commands in a manner which minimizes the delay effects of seeking and rotational offset (latency). overhead The command processing time required by the controller, host adapter, or drive prior to any actual disk accesses. Overhead time for reading a sector can be defined as the sum of reading the gap, synchronization, header, EDC and ECC. overwrite To write data on top of existing data, erasing the original data. G 8 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

9 parity An error checking technique wherein the sum of the bits in a data byte is used to set or reset an extra parity bit, depending on whether the sum is an odd or an even number. A second parity check after the data is transferred to a new location checks that the new parity bit matches the transferred bit. Parity checking can only detect an odd number of bit errors (1,3,5, etc.). Parity is defined as odd or even, depending on which condition (odd or even) is used to set the parity bit. parking zone A position in a non-data area on a disk platter reserved for resting the heads when power is off. Using this area prevents the heads from touching the surface in data areas upon power down, adding to the data integrity and reliability of the disk drive. The parking zone is most often inside the disk s inner-most cylinder. partition A portion of a hard disk accessed as one logical volume by the system. Also refers to a band or notch. See Banding. performance A measure of drive speed during normal operation. Factors affecting drive performance are seek times, transfer rate, and command overhead. physical format The actual layout of cylinders, tracks, and data sectors on a disk drive. physical sector See sector, data. platter See hard disk.. POH Abbreviation for power-on hours. The unit of measurement for mean time between failures as expressed in the number of hours that power is applied to the device, regardless of the amount of actual data transferred. See MTBF. prefetch The technique of buffering data into cache RAM by reading subsequent blocks in advance to anticipate the next request for data. Prefetch speeds up disk accesses to sequential blocks of data. queue A prioritized list or set of processes. A queue may be a FIFO (first-in, first-out), LIFO (last-in, first -out) or a random-access entity. queue tag The value associated with an I/O process that uniquely identifies it from other queued I/O processes in the logical unit from the same initiator. queued I/O process An I/O process that is in the command queue. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 9

10 RAM Acronym for random access memory. A type of memory media that allows information to be stored and retrieved rapidly by a microprocessor or controller. The information may be stored and retrieved in any order with no priorities given. RAM disk A phantom disk drive for which a section of system memory (RAM) is set aside to hold data, just as if it were an actual disk. Data access is extremely fast, but the data is lost when the system is reset or turned off unless time is allowed for storage on a bulk device before shutdown. read The function of detecting, processing and transmitting data that has been recorded (written) on a magnetic disk or some other media. read/write head The tiny transducer used to create and detect magnetic patterns on the disk that represent data. The head may be an electromagnetic coil and metal pole piece or a combination of a coil (for writing) and a magneto-resistive element (for reading). A disk has a single read/write head per side and usually (but not always) a head on both sides. reconnect The act of reviving a nexus to continue an I/O process. An initiator reconnects to a target using the SELECTION and MESSAGE OUT phases after winning arbitration. The target reconnects to the initiator using RESELECTION and MESSAGE IN phases after winning arbitration. reconnection The state which results from a reconnect. It exists from the assertion of BSY in the SELECTION or RESELECTION phase and lasts until the next BUS FREE phase. RLL Abbreviation for Run Length Limited. An advanced method used to encode (or compress) data for storage on a disk. RLL encoding stores almost 50 percent more data than MFM (Modified Frequency Modulation). RLL code improves MFM code by encoding data bits in groups rather than singly. Many encoding schemes are possible. The best achieve optimum values of code rates, clocking, power spectrum, error propagation and encoding complexity. A number pair (e.g., 1,7) is usually stated with RLL references. It refers to the minimum number of 0;s(1) and the maximum number of 0 s (7) that can separate data 1 s stored on the disk. ROM Acronym for read-only memory. Usually in the form of a PROM that contains data or programs that can be accessed and read but not modified by the system. rotary actuator The rotary actuator is a positioner assembly that has largely replaced the stepper motor. It allows closed-loop feedback positioning of the heads, which is far more accurate than stepper motors and has greater component longevity. See also stepper and voice coil. G 10 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

11 rotational latency The delay between when the controller starts looking for a specific block of data on a track and when that block rotates around to where it can be accessed by the read/write head. On average, it is half the time of a full disk rotation. SCA Single Connector Attachment. A drive connector that combines the signal and power connectors into one. Typically, SCA-type connectors are used in RAID (Redundant Array of Inexpensive Devices) systems. SCA-2 An improved Single Connector Attachment that incorporates two electrostatic discharge (ESD) pins on either end of the connector to improve safety when making a connection. SCAM-1 SCSI Configured Automatically. A plug-and-play method used in some drives. SCSI Acronym for small computer system interface (pronounced scuzzy ), an American National Standards Institute (ANSI) standard protocol for the interface between a computer and up to 16 devices. SCSI is one of the most flexible and powerful interfaces available. SCSI 1 The first small computer system interface standard. SCSI 2 An enhanced small computer system interface as defined and published by ANSI in standard X One of the major features of SCSI 2 is integrating the controller into the peripheral device, making the device independent of the initiator. SCSI 3 A new set of related ANSI standards are currently under development by the X3T10 committee. The old SCSI 2 standard has been divided into a new set of standards for SCSI 3. Some of these [working draft] standards are : SAM (SCSI Architecture Model) for the architecture; SBC (SCSI Block Commands) for the disk drive specific command set. SPC (SCSI Primary Commands) for the primary command set; and SIP (SCSI Interlocked Protocol) for the protocol layer; SPI (SCSI Parallel Interface) for the physical layer; Layering the standards documents in this manner allows substitution of parts of the structure as new technology arrives. SCSI address The unique address assigned to a SCSI bus device. Normally, the address is assigned and set during system installation with priority being a consideration. A SCSI address is a value of 0 to 7 (or 0 to 15 for wide SCSI). SCSI bus A multi-signal parallel bus that interconnects SCSI devices in a daisy-chain fashion. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 11

12 SCSI device A host adapter or a target controller that can be attached to the SCSI bus. SCSI ID The bit-significant representation of the SCSI address referring to one of eight (or one of sixteen) data lines. sector, data A physical section of space along a track on the disk, or, the data that is stored in that section. Certain hard disks have data sectors that are a maximum of 524 data bytes long, plus several additional bytes for error detection and correction codes. Not to be confused with servo sectors. seek A movement of the disk read/write head in or out to locate a specific track. segmented cache buffer A cache buffer that is organized into multiple track lines. Segmenting the cache allows track data to be saved in separate segments when the head is switched rather than having to erase the entire cache. Segmenting the cache enables command reordering on a more efficient track-basis rather than on a command-basis. sense data Information returned to an initiator regarding error conditions in the drive. servo sector time The time (in µsec) between reading one servo header (or spoke ) and reading the next header. servo spoke data In embedded servo technology, digital and quadrature analog servo data is written (embedded) in multiple headers (or spokes ) on each track on the data-recording area of each disk surface. The digital portion of the spoke data are read and used to locate the correct track, spoke, and head number. The quadrature analog signal portion is detected and used by a servo feedback control loop to precisely position the head on the track center. servo surface A separate disk surface containing only positioning and disk timing information but no data. This surface is used with dedicated servo systems and is generally thought to be obsolete technology. settle time The interval between when a track-to-track movement of the head stops and when the residual vibration and movement dies down to a level sufficient for reliable reading or writing. See also Bus Settle Time. shock rating A durability measurement for hard drives (expressed in Gs) of how much shock or sudden movement a disk can sustain without damage. G 12 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

13 signal assertion The act of driving a signal to the true (logical-one) state. An asserted signal on the SCSI bus is a low voltage resulting from driving a transistor ON. signal negation The act of driving a signal to the false (0) state, or allowing the cable terminators to bias the signal to the false state by placing the data driver in the high impedance (off) condition. A negated signal on the SCSI bus is a high voltage resulting from all OR-tied transistors being OFF. signal release The act of allowing the cable terminators to bias the signal to the false state by placing the bus driver in the high impedance (off) condition. single-ended termination One of two methods for terminating the SCSI bus, characterized by signal values that conform to the ANSI-defined levels for SCSI implementation. Typically used for short cable runs. See also differential termination. skew To shift sector addresses when switching tracks or cylinders to create a slight overlap under the read/write heads. The overlap works to delay the arrival of the next (in sequence) sector from arriving under the selected head until the track or cylinder switch has been done. Skewing minimizes latency time (increasing data throughput) when data on the drive is accessed sequentially. S.M.A.R.T. Self-Monitoring and Analysis Reporting Technology. The continual monitoring of the drive s operating condition with reports sent to the host computer. Similar to Quantum s EWS (Early Warning System) used in some drives. spindle The center shaft of the disk upon which the drive s platters are mounted. Usually contains an integral dc brushless motor. sputter A type of coating process used to apply the magnetic coating to high-performance disks. In sputtering, the disks are placed in a vacuum chamber and the coating is vaporized and deposited on the disks. The resulting surface is hard, smooth, and capable of storing data at high density. status One byte of information sent from a target to an initiator upon completion of each command. substrate The material the disk platter is made of beneath the magnetic coating. Hard disks are generally made of an aluminum-magnesium alloy or glass, while the substrate of flexible diskettes is usually mylar. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 13

14 surface The top or bottom side of a disk, which is coated with the magnetic material for recording data. On some drives, one surface may be reserved for positioning servo information. This servo technique is now replaced with the more efficient imbedded servo technology. See servo data. synchronous data transfer Data transfer that allows transfer of multiple blocks of data between request or acknowledgment signals, since request and acknowledgment signals need not be sent before and after each block. This method is faster than asynchronous data transfer. target An SCSI device that performs an operation requested by an initiator. target routine An I/O process directed to a target and not to a logical unit. thin film A type of coating used for disk surfaces and read/write heads. Thin-film surfaces allow more bits to be stored per disk. Thin-film heads allow closer flying heights. third-stroke seek A method of evaluating the power requirements of a hard drive. It involves monitoring drive current while seeking to a selected track, waiting for 1/2 a revolution, then seeking to a track that is 1/3 of the total actuator stroke from the first. The seek/wait cycle is usually repeated three times. TPI Abbreviation for tracks per inch. The number of tracks or cylinders that are written in each inch of travel across a disk surface. track One of many concentric magnetic circle patterns on a disk surface that contain data. See cylinder. track density How closely the tracks are packed on a disk surface, specified in tracks per inch (TPI). track-to-track seek time The time required for the read/write heads to move to an adjacent track. transfer rate The rate at which the disk sends and receives data from the controller. true Refers to the logical-one (or asserted ) state of a binary number. See also, signal assertion. G 14 Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual

15 unformatted capacity The total number of bytes of data that can be put on a disk drive. Formatting the disk requires approximately 20% of this space to record servo data, addresses, boundary definitions, and timing information. After formatting, user data can be stored on the remaining disk space, known as the formatted capacity. voice coil A type of motor used to move the disk read/write heads to the desired track. A voice coil actuator works like a loudspeaker. A coil is suspended in a magnetic field. A servocontrolled current in the coil generates an electromagnetic force that moves the coil. The moving coil moves the actuator with its attached heads to the desired position on the disk. See also rotary actuator. wide SCSI SCSI protocol permits wide data transfers of 16 or 32 bits. wide data transfer Data transfer that allows information transfer across 16 (or future 32) bits. Faster than standard 8-bit data transfer. write The operation of recording or storing data on a magnetic or other media. See also, read. Atlas II XP32275/XP34550/XP39100 SCSI Hard Disk Drives Product Manual G 15