IP Router QUICK START GUIDE

Transcription

1 IP Router QUICK START GUIDE Part Number: Product Release: 2.97 August 2009

2 Copyright 2009 Force10 Networks Inc. All rights reserved. Force10 Networks reserves the right to change, modify, revise this publication without notice. The hardware and software described herein are furnished under a license or non-disclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement. It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium - electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied with the product for any purpose other than the purchaser s personal use without the express written permission of Force10 Networks Inc. Trademarks Adit and Force10 Networks are registered trademarks of Force10 Networks, Inc. Force10 and the Force10 logo are trademarks of Force10 Networks, Inc. or its affiliates in the United States and other countries and are protected by U.S. and international copyright laws. All other brand and product names are trademarks or registered trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Force10 Networks reserves the right to make changes to products described in this document without notice. Force10 Networks does not assume any liability that may occur due to the use or application of the product(s) described herein. Corporate Contact Information: Force10 Networks, Inc. 350 Holger Way San Jose, CA Phone: +1 (866) or +1 (408) Technical Assistance Center: access-support@force10networks.com Phone: (US) Phone (International/Direct): Supporting Software Versions: IP Router Release 2.97 Adit 600 Controller Release

3 QUICK START GUIDE In this Guide Installation Basic Setup PPP Internet Connection and Public IP Address Routing Frame Relay Internet Connection and Public IP Address Routing Internet Connection using PPP, NAT/PAT and Firewall Filters Internet Connection using NAT and Static NAT Addresses Back-to-Back with PPP Back-to-Back with Multi-Link PPP Back-to-Back with Frame Relay

4 Installation Installation Installation of the router card into the Adit 600 chassis: Unit can be on or off Router card will work in any slot Slide card into slot until fully seated Router has completed its boot cycle when CRD light is solid NOTE: Configuration can be done with CLI commands from the Adit 600 controller or with the Router Menu-Driven Software. Basic Setup set {ds0-addr} type data connect {slot:port:trunk} {slot:port:channel} set {router-addr} proxy Confirm DS0 is set to type data. ds0-addr = {slot:port:channel} of DS0 Example: set a:1:1-24 type data Cross-connect T1 to router card. Example: connect a:1:1-24 6:1:1 (router in slot 6) Disable/enable router proxy. router-addr = {slot:port} of router card. Example: set 6:1 disable. set {slot:port} up Set Router LAN as In-Service. Example: set 6:1 up telnet {router_card-addr} Local and Remote Profile Setup reset Telnet to Router card. router_card-addr = {slot} location of router card Example: telnet 6 (if earlier than 3.0 release {slot:port} must be used) For most router configuration changes to go into effect, the router must be reset. Best practice is to always reset the router after making configuration changes. 4 IP Router - Release 2.97

5 PPP Internet Connection and Public IP Address Routing Router in Slot 1 ISP Router that provides the Internet connection. Quick Start Guide PPP Internet Connection and Public IP Address Routing set clock1 a:1 Set primary master transmit clock source rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set 1:1 ip address add 1 static ip network set 1 trunk 1 set 1:1:1 encapsulation ppp Rename "LocalUnit" (default) to "Boulder" Set the ethernet IP address, in the conventional IP Set the WAN named to be mapped to trunk 1 Set the encapsulation on trunk 1 to PPP IP Router - Release

6 Frame Relay Internet Connection and Public IP Address Routing Frame Relay Internet Connection and Public IP Address Routing Router in Slot 1 ISP Router that provides the Internet connection. set clock1 a:1 Set primary master transmit clock source rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set 1:1 ip address add 1 static ip network set 1:1:1 encapsulation fr set 1 lmi annexd set 1 trunk 1 set 1 dlci 101 Rename "LocalUnit" (default) to "Boulder" Set the ethernet IP address, in the conventional IP Set the encapsulation on trunk 1 to Frame Relay Disable LMI to Annex D Set the WAN named to be mapped to trunk 1 Set the DLCI number 6 IP Router - Release 2.97

7 Internet Connection using PPP, NAT/PAT and Firewall Filters Internet Connection using PPP, NAT/PAT and Firewall Filters Router in Slot 1 ISP Router that provides the Internet connection. Router with NAT/PAT and Firewall Filters. set clock1 a:1 Set primary master transmit clock source rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set 1:1 ip address set 1 nat enable set 1 nat port dynamic set 1 nat address add 1 static ip network Rename "LocalUnit" (default) to "Boulder" Set the ethernet IP address, in the conventional IP Set the WAN named enable NAT mapping Set the WAN named to set NAT port mapping to be dynamic Set the WAN named NAT address IP Router - Release

8 Internet Connection using PPP, NAT/PAT and Firewall Filters add 1 firewall 1 pass incoming log telnet /32 xxx.xxx.xxx.xxx/32 add 1 firewall 2 pass inout nolog ping /32 xxx.xxx.xxx.xxx/32 add 1 firewall 3 pass inout nolog ping / /0 add 1 firewall 4 pass inout nolog tcp / /0 add 1 firewall 5 pass inout nolog udp / /0 set 1 trunk 1 set 1:1:1 encapsulation ppp Adds a Firewall rule to the WAN. Where xxx.xxx.xxx.xxx is the host s IP address at the far end that will be able to ping or telnet to the router /0 will allow any other host at the far end to ping and/or telnet to the router. Adds a Firewall rule to the WAN. Where xxx.xxx.xxx.xxx is the host s IP address at the far end that will be able to ping or telnet to the router /0 will allow any other host at the far end to ping and/or telnet to the router. Adds a Firewall rule to the WAN. Adds a Firewall rule to the WAN. Adds a Firewall rule to the WAN. Set the WAN named to be mapped to trunk 1 Set the encapsulation on trunk 1 to PPP 8 IP Router - Release 2.97

9 Internet Connection using NAT and Static NAT Addresses Internet Connection using NAT and Static NAT Addresses Router in Slot 1 ISP Router that provides the Internet connection. Router with NAT and Static NAT addresses. set clock1 a:1 Set primary master transmit clock source rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set ethernet ip address set ip gateway set 1:1 ip address set 1 nat enable set 1 nat port dynamic set 1 nat address Rename "LocalUnit" (default) to "Boulder" Set the Ethernet IP address and Subnet Mask, for the Set the IP gateway (default route) for the Unit Set the Ethernet IP address, in the conventional IP Set the WAN named enable NAT mapping Set the WAN named to set NAT port mapping to be dynamic Set the WAN named NAT address IP Router - Release

10 Internet Connection using NAT and Static NAT Addresses add 1 static ip network add 1 static nat address add 1 static nat address add 1 static nat address add 1 static nat address set 1:1:1 encapsulation fr set 1 lmi annexd set 1 trunk 1 set 1 dlci 101 Add static NAT bi-directional mapping to wan1 Add static NAT bi-directional mapping to wan1 Add static NAT bi-directional mapping to wan1 Add static NAT bi-directional mapping to wan1 Set the encapsulation on trunk 1 to Frame Relay Disable LMI Annex D Set the WAN named to be mapped to trunk 1 Set the DLCI number is the static NAT address assigned to the router is the static NAT address assigned to the controller is the static NAT address for a server* is the static NAT address for a host*. *In the private network that can be reached from the outside world. There can be up to 16 static NAT addresses, therefore the actual range can be to Only 4 were used in this example. 10 IP Router - Release 2.97

11 Back-to-Back with PPP Quick Start Guide Back-to-Back with PPP The following configuration will set up two Adit 600 Routers back-to-back with PPP. Boulder Router in Slot 1 rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set 1:1 ip address set 1:1 phy auto set 1 rip ip updates never add 1 static ip network set 1:1:1 encapsulation ppp set 1 trunk 1 Boulder /24 24 DS0s wan1: PPP or Frame Relay Static Routes IP Denver / 24 Rename "LocalUnit" (default) to "Boulder" Set the Ethernet IP address, in the conventional IP Set the Physical Specifications to auto-negotiate Set to not send RIP updates Set the encapsulation on trunk 1 to PPP Set the WAN named to be mapped to trunk 1 IP Router - Release

12 Back-to-Back with PPP Denver Router in Slot 1 set clock1 a:1 Set primary master transmit clock source rename 1 "LocalUnit" "Denver" rename 1 "RemoteUnit" set 1:1 ip address set 1:1 phy auto set 1 rip ip updates never add 1 static ip network set 1:1:1 encapsulation ppp set 1 trunk 1 Rename "LocalUnit" (default) to "Denver" Set the ethernet IP address, in the conventional IP Set the Physical Specifications to auto-negotiate Set to not send RIP updates Set the encapsulation on trunk 1 to PPP Set the WAN named to be mapped to trunk 1 12 IP Router - Release 2.97

13 Back-to-Back with Multi-Link PPP Quick Start Guide Back-to-Back with Multi-Link PPP The following configuration will set up two Adit 600 Routers back-to-back with Multi- Link PPP. Boulder Router in Slot 1 connect a:2:all 1:1:2 Connect all of T1-2 to the Router that is in slot 1 rename 1 "LocalUnit" "Boulder" Rename "LocalUnit" (default) to "Boulder" set 1:1:1-2 multilink group 1 Assign 1:1:1-2 to multilink group 1 rename 1 "RemoteUnit" set 1:1 ip address add 1 static ip network set 1 trunk multilink group 1 Set the Ethernet IP address, in the conventional IP Set the WAN named to be mapped to trunk multilink group 1 IP Router - Release

14 Back-to-Back with Multi-Link PPP Denver Router in Slot 1 set clock1 a:1 Set primary master transmit clock source connect a:2:all 1:1:2 Connect all of T1-2 to the Router that is in slot 1 rename 1 "LocalUnit" "Denver" Rename "LocalUnit" (default) to "Denver" set 1:1:1-2 multilink group 1 Assign 1:1:1-2 to multilink group 1 rename 1 "RemoteUnit" set 1:1 ip address add 1 static ip network set 1 trunk multilink group 1 Set the ethernet IP address, in the conventional IP Set the WAN named to be mapped to trunk multilink group 1 14 IP Router - Release 2.97

15 Back-to-Back with Frame Relay Quick Start Guide Back-to-Back with Frame Relay The following configuration will set up two Routers back-to-back with Frame Relay. Boulder Denver / /24 Boulder Router in Slot 1 Boulder /24 set clock1 internal Set primary master transmit clock source rename 1 "LocalUnit" "Boulder" rename 1 "RemoteUnit" set 1:1 ip address set 1:1 phy auto add 1 static ip network set 1:1:1 encapsulation fr set 1 lmi disable set 1 trunk 1 24 DS0s wan1: PPP or Frame Relay Static Routes IP Denver / 24 Rename "LocalUnit" (default) to "Boulder" Set the Ethernet IP address, in the conventional IP Set the Physical Specifications to auto-negotiate Set the encapsulation on trunk 1 to Frame Relay Disable LMI (Local Management Interface) Set the WAN named to be mapped to trunk 1 IP Router - Release

16 Back-to-Back with Frame Relay set 1 dlci 101 Set the DLCI number Denver Router in Slot 3 set 3 default disconnect 3 Disconnect all connections to the router in slot 1 set clock1 a:1 Set primary master transmit clock source connect a:1:all 3:1:1 Connect all of T1-1 to the Router that is in slot 1 rename 3 "LocalUnit" "Denver" rename 3 "RemoteUnit" set 3:1 ip address set 3:1 phy auto add 3 static ip network set 3:1:1 encapsulation fr set 3 lmi disable set 3 trunk 1 set 3 dlci 101 reset 3 Rename "LocalUnit" (default) to "Denver" Set the ethernet IP address, in the conventional IP Set the Physical Specifications to auto-negotiate Set the encapsulation on trunk 1 to Frame Relay Disable LMI (Local Management Interface) Set the WAN named to be mapped to trunk 1 Set the DLCI number 16 IP Router - Release 2.97