Tellabs 1000 Special Services Application and Ordering Guide

Transcription

1 Tellabs 1000 Special Services Application and Ordering Guide June 2014 Version 1.0

2 Table of contents 1 Overview: Tellabs 1000 System Features: Tellabs 1000 Solutions Network Configurations: Network Topology: Tellabs 1000 Special Services Application Summary Appendix One: Appendix Two: Shelf Ordering Information Tellabs 1000 Detail Mechanical Product Information Appendix Three: Plug In Ordering Information Tellabs 1000 Detail Module Product Information REVISION HISTORY Rev Date Author(s) Comments /02/2014 Tod Brinkerhoff Document Creation Page 2 of 20

3 1 Overview: Service Providers are faced with many complex challenges in their last mile access network. One of those challenges is the continued demand for business services. The second challenge is to provide the most cost effective infrastructure. First choice when economically feasible is to place fiber for the building entrance facility in lieu of copper. The third challenge is to continue providing and supporting business and residential services while many of their incumbent equipment providers have Manufacture Discontinued (MD d) their product lines. The difficult job for an OSP Planner and Engineer is to continue to provide these traditional TDM services while the clear network initiatives is to transition to an all IP Ethernet-centric Network. Tellabs also views the IP Network Transition as the preferred growth technology, however, the customer s current needs must be also be met due to state PUC requirements and existing tariffs until this is modified or eliminated. Another challenge is that many of the customary technologies that were used in delivering traditional TDM services are now Manufacture Discontinued. The list of MD d access equipment includes but is not limited to Alcatel-Lucent s SLC96/SLC Series5/SLC2000 and Litespan, Zhone s (Nortel) AccessNode, GenBand s (Nortel) DMS1 Urban, Siemen s AE914 and most recently Adtran s TA1500. Adtran has also MD d the TA1148 and TA1248, which are copper fed DSLAMs. The Tellabs 1000 Multi-Service Access Platform is a good choice for a low cost replacement of these technologies. Tellabs Access is committed to support our customers with the Tellabs 1000 with over 9,000 systems carrying traffic. 2 Tellabs 1000 System Features: The Tellabs 1000 MSAP, also known as the AccessMax, DMAX1120 and UMC1000 is a modern and flexible Integrated Multiservice Access Platform (IMAP). It can economically serve from as few as six to more than two thousand subscribers. Designed with a modular, building-block approach, the Tellabs1000 supports a variety of transmission media to provide service in a wide range of network topologies. The Tellabs 1000 uses state-of-the-art technologies to provide traditional and forward-looking subscriber services. The Tellabs 1000 family of products provides local loop voice, data, xdsl and Ethernet solutions. Each Tellabs 1000 product uniquely solves pressing service delivery needs. The Tellabs 1000 also provides legacy narrowband and wideband services while utilizing existing backhaul facilities, including fiber and T1/E1 or HDSL copper plant. The unique backplane design combines line card powering and heat dissipation technologies, delivering multiple high-density services. Tellabs equips a number of remote telecom cabinets with the Tellabs 1000 channel bank assembly that can provide the following: Page 3 of 20

4 1. Full set of services on one platform (POTS, ADSL, VDSL, Ethernet, Specials, Hicaps, DS3) with full TSI capabilities to assign any service to any slot/port 2. High capacity OC3c, OC12c and GigE transport (software dependent) 3. SONET compliant OC3 for inter-terminal transport over SONET rings. The card supports GR253 compliant SONET 1+1 Automatic Protection Switching (APS) 4. One set of fibers for all services. No need for separate fibers for each service type delivered. 5. State of the art EMS Panorama a fully robust EMS 6. Lowest cost Customer Premises Network Element providing a full set of required services. Refer to appendix one for a detail list a. Locally Switched b. Locally Switched Specials c. Non-Locally Switched Services d. Non-Switched Service 7. Support for up to 112 DS1s and MI3 functionality. 8. Upgrade to IP with software and cards. FP16 offers GigE transport and uplink, 10/100 Ethernet services, VDSL2 and VDSL2 bonded services using PTM, ADSL2+ ATM services. Page 4 of 20

5 Page 5 of 20

6 Page 6 of 20

7 3 Tellabs 1000 Solutions Local Exchange Terminal (CO) to Remote Service Terminal OSP CEV, HUT or Customer Premises: Single shelf to full rack (8-shelf) deployments for POTS, Specials, Hi-Cap services Small shelf 1048 CBA 10 service slots for POTS, Specials, Hi-Cap Services Small shelf 1048 Retrofit Kit 10 service slots for POTS, Specials, Hi-Cap Services Local Exchange Terminal in CO only Single shelf to full rack (8-shelf) deployments for POTS, Specials, Hi-Cap Services Fiber-To-The-Business (FTTB) Customer Premises Remote Terminals: 100 Lines RST 100 Wall Mount 200 Lines RST 200 Wall Mount 200 Lines RST 200 Wall Mount Expansion Kit See Appendix Two for shelf detailed descriptions and ordering information. See Appendix Three for Module detailed descriptions and ordering information. See Section Six for Module quantity of services offered. Contact your regional Sales representative for a detail quote or pricing information as shown below: Name Title Office Cell Marcus Bellard Phillip Gardner Mike Kavanagh Monty Morales Tod Brinkerhoff Ron Franklin Carter Gaddis Executive Account Manager - West Account Manager - Northwest Executive Account Manager - East Executive Account Manager - Central Sales Engineering Director Senior Sales Engineer West Senior Sales Engineer Central [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Page 7 of 20

8 4 Network Configurations: A Tellabs 1000 Linear Chain configuration can extend five transport spans deep from the LET with up to 32 total remote terminals. In this configuration, the LET resides in the Central Office with the switch. The RST, which resides in a remote cabinet, in a rack, in a CEV, or on a subscriber s premises, delivers an array of services. See Figure 1. Figure 1. Page 8 of 20

9 A Tellabs 1000 Star configuration can connect directly to up to 32 RSTs, five transport spans deep. In this configuration, the LET resides in the Central Office with the switch. The RST, which resides in a remote cabinet, in a rack, in a CEV, or on a subscriber s premises, delivers an array of services. See Figure 2. Figure 2. Page 9 of 20

10 The Tellabs 1000 system is ideal for co-location because it delivers all the critical voice services, as well as ISDN, DDS, 2-wire and 4-wire specials, Pay/Coin service, T1, HDSL, ADSL, and VDSL in any combination, all from a single shelf. It then concentrates voice and data traffic, providing for efficient use of transport facilities. See Figure 3. Figure 3. Page 10 of 20

11 An alternate application for D4 CBA replacement is to deploy a Tellabs 1000 as a standalone LET channel bank, either as a single shelf or up to 8 individual shelves in a single bay. All that is required per shelf are redundant CPU3 and L-PSU common cards with an optional MTU or DBP card for metallic testing. Then you can install up to 4-T1x (non-powered) cards to support up to 96 DSOs per shelf. There are 21 slots available to place any POTS or Special Service cards required. These shelves can be installed in the CO cabled directly to the MDF and DSX-1, an RT cabled directly to Krone Blocks or Protector Blocks and mux or a combination of both. See Figure 3A. Figure 3A. Page 11 of 20

12 5 Network Topology: The following are examples of network deployments to provide voice and data service in the above mentioned configurations. Although many of these show POTS cards, the same applies for any DSO, DS1, DS3 or Ethernet service. With the exception of deploying Ethernet using GigE uplink cards being required to be placed in slots 12/13 of the CBA, the first 22 slots are considered universal slots for any service type. In any of these topologies, the transport can be fiber or copper fed. The Linear chain example shows the extension of an LET to multiple RSTs in a drop and continue configuration with a single shelf solution using a mixture of fiber and copper. It is always best to use fiber when available. The LET is connected via fiber to RST1 with RST1 to RST2 and RST2 to RST3 via copper feed. Each RST s DS0s are mapped to particular LET T1X cards for delivery to a local Digital Cross-Connect system (DCS) or mux to be distributed to the ultimate end location. The TSI functionality allows any RST DSO to be assigned to any LET T1X. In some Service Provider s networks, the placement of plugs will depend upon OSS restrictions or models. The caution with this configuration is any break on an upstream transport link will sever service to the trailing RSTs. See Figure 4. Figure 4. Page 12 of 20

13 The Star example shows the extension of an LET directly connected to multiple RSTs with a single shelf solution. The LET is directly connected via fiber to RST1, RST2 and RST3 via fiber. Each RST s DS0s are mapped to particular LET T1X cards for delivery to a local Digital Cross-Connect system (DCS) or mux to be distributed to the ultimate end location. The TSI functionality allows any RST DSO to be assigned to any LET T1X. In some Service Provider s networks, the placement of plugs will depend upon OSS restrictions or models. With this configuration, any transport link cut will only affect the RST directly connected to the LET. See Figure 5 Figure 5. Page 13 of 20

14 The Star example shows the extension of an LET directly connected to multiple RSTs with a multi-shelf solution. The LET is directly connected via fiber to RST1, RST2 and RST3 via fiber. This configuration allows for greater bandwidth on a per LET shelf basis as well as additional slots if more universal/local MDF connections are required. Each RST s DS0s are mapped to particular LET T1X cards for delivery to a local Digital Cross-Connect system (DCS) or mux to be distributed to the ultimate end location. The TSI functionality allows any RST DSO to be assigned to any LET T1X. In some Service Provider s networks, the placement of plugs will depend upon OSS restrictions or models. With this configuration, any transport link cut will only affect the RST directly connected to the LET. See Figure 6 Figure 6. Page 14 of 20

15 6 Tellabs 1000 Special Services Application Summary Tellabs has provided special services on the Tellabs 1000 since its inception. Tellabs continues to re-spin the Tellabs 1000 modules to improve the performance of the card as well as deal with part obsolescence. Many of these cards have been used since the early 1990s so components naturally become obsolete and component vendors leave the business. Tellabs continues to insure that the Tellabs 1000 is a viable product for our customers networks and will find other component vendors to supply the most cost effective parts. However, sometimes Tellabs must also re-spin Network Element software to keep up with these changes. These are not new loads, but dot (.) releases to our ATM load (FP10.0) and Ethernet load (FP16.0). Page 15 of 20

16 7 Appendix One: This chart is provided to assist the Planner / Engineer prepare for the upcoming Adtran TA1500 MD expected by the end of This product had been the mainstay in many service providers network to use as a D4 CBA replacement or Special Services delivery platform. For those customers that use the Telcordia suite of software, the Tellabs 1000 is fully OSMINE compliant. Page 16 of 20

17 Page 17 of 20

18 8 Appendix Two: Shelf Ordering Information 8.1 Tellabs 1000 Detail Mechanical Product Information Below is a basic list of shelves, fan assemblies and intrabay cables used to provide service. The same units are used whether configured as an LET or RST. Shelves and Accessories SBPQABF Fan Tellabs 1000 Fan Tray Installation Kit Cover Tellabs 1000 Front Cover Kit Mounting Bracket Tellabs 1000 Projection Mount Adaptor Kit (23" BY 5") Shelf (wired) TLAB1000V2 Backplane Wire Wrap (no cable stubs) Shelf (conn) TLAB1000V2 Backplane Connectorized EBF 3 Expansion Bank Fibers - 3 meter (1 required per ELU) EBF 10 Expansion Bank Fibers - 10 meter (1 required per ELU) EBF 3 BB Broadband Expansion Bank Fibers - 3 meter (1 required per ELU-3) EBF 10 BB Broadband Expansion Bank Fibers - 10 meter (1 required per ELU-3) MTU I/F Metallic Test Unit Interface Cable (daisy chain to expansion shelves) RAI Wire Kit Remote Alarm Interface Wiring Kit Wall Mount Tellabs 1000 Wall Mount Kit FTTB RST-100 Wall Mount with Protector FTTB RST-100 Wall Mount without Protector FTTB RST-200 Wall Mount with Protector Shelf, Fan, Wall Mount Bracket, Cabling, Corning 24 fiber cabinet, Protector Panel and LPK23-VV 12 AH LP System Shelf, Fan, Wall Mount Bracket, Cabling, Corning 24 fiber cabinet and LPK23-VV 12 AH LP System Shelf (2), Fan, Wall Mount Bracket, Cabling, Corning 24 fiber cabinet, Protector Panel and LPK23-VV 12 AH LP System Shelf (2), Fan, Wall Mount Bracket, Cabling, Corning 24 fiber cabinet and LPK23-VV 12 AH LP System Shelf, Fan, Wall Mount Bracket, Cabling, Protector FTTB RST-200 Wall Mount without Protector FTTB RST-Expansion Kit with Protector FTTB RST-Expansion Kit without Protector Shelf RSC 1048 Shelf Fan RSC 1048 Fan Assembly RSC 1048 Retrofit Kit Shelf, Fan, Mounting Bracket, Cabling EMAX Plus retrofit Kit with Protector EMAX Plus retrofit kit without Protector Panel and LPK23-VV 12 AH LP System Shelf, Fan, Wall Mount Bracket, Cabling and LPK23- VV 12 AH LP System Shelf, Fan Brackets, Cabling, Protector Panel and Power Harnesses for third party cabinets Shelf, Fan, Brackets, Cabling, and Power Harnesses for third party cabinets Page 18 of 20

19 9 Appendix Three: Plug In Ordering Information 9.1 Tellabs 1000 Detail Module Product Information Common Control Units SBCTA24 CPU-3 Central Processor SBCTEF0 DLP Data Link Processor SBC3BA0 IPMI-3 Internet Protocol Management Interface SBPUA05 L-PSU Local Exchange Power Supply Unit SBP1AAC R-PSU Remote Subscriber Power Supply SBPUCC1 N-PSU Network Subscriber Power Supply SBTEAAA MTU Metallic Test Unit (required for fgte 4TEL testing) SBTEAAF OSI Operations System Interface SBLSTL2 DBP Digital Bypass Pair Unit SBCPKMF RAI Remote Alarm Interface SBTCLP0 ETI External Timing Interface SBCTCBN ELU Expansion Link Unit SBCTBBN EBC Expansion Bank Control SBCTCXB EBC-3+ Broadband Expansion Link Unit SBCTBXB ELU-3 Broadband Expansion Bank Control Unit Transceivers SBUIAEP GBE222 GBE222 UPLINK/TRANSPORT CARD SFP GIGE SX SFP GIGE LX SFP GIGE ZX SBHSG7V OC3C-XCVR OC3C Fiber Optic Transceiver (SC) - to RST/LET SBUIAFL OC12C-XCVR OC12C Fiber Optic Transceiver (SC) - to RST/LET SBT1MS0 OC3 OC3 Fiber Optic Transceiver (SC) - SONET SBHSW90 DS3 T3 Channelized or Intact (non-powered) SBTCH15 TIX-XCVR T1 Transceiver (non-power) SBTCH24 TI- XCVR T1 Transceiver (Powered) * SBT1NNL T1HD2-XCVR T1 HDSL2 TRANSCEIVER (ADTRAN) (powered) * SBT1LN0 T1HD4-XCVR T1 HDSL4 TRANSCEIVER (ADTRAN) (powered) * SBT1LR0 T1HD2-XCVR T1 HDSL2 TRANSCEIVER (ADTRAN) (powered) * SBT1NN0 T1HD4-XCVR T1 HDSL4 TRANSCEIVER (ADTRAN) (powered) *Customer dependent on which version to order Service Cards SBLSAU0 L-POTS LET POTS Channel Unit SBLSPN4 L-ISDN LET ISDN Unit SBLSGVW L-PAY LET Pay Phone Channel Unit SBLSDB3 L-UVG LET Universal Voice Grade Channel Unit SBLSKS0 L-EBS LET ELECTRONIC BUS.SET CHNL.UNIT Page 19 of 20

20 SBC2450 MCU-AFC METALLIC CHANNEL UNIT - Alarm Card SBC3MME SS 2/4 SPECIAL SERVICES 2W/4W (FX, DID, ETO, PLAR) SBL1NRJ E&M E&M CHANNEL UNIT - DX SIGNALING & POST EQUALIZATION SBLSJE9 TO -2 wire Transmission Only (2 wire) Unit SBLSJE9 TO-4 wire Transmission Only (4 Wire) Unit SBTCH15 TIX T1 Transceiver (non-power) - Fractional T SBTCHH2 T1A T1 Async Channel Unit (powered) SBTCHG3 T1AX T1 Async Channel Unit (non-power) SBLSMR0 DSO-DP Digital Signal Zero Data Port - 56k SBUIAF4 ADSL2+6+6B ADSL WITH BONDING VERSION 2 ANSI SBUIAFA ADSL2+6+0B ADSL WITH BONDING VERSION 2 ANSI SBUIAET VDSL2 6+6B VDSL2 6+6 With Bonding SBL1WXP R-POTS RST POTS Channel Unit SBC2TU9 R-UVG RST Universal Voice Grade Channel Unit SBL1TUM R-ISDN R-ISDN (2) SBC2230 R-PAY RST Payphone Channel Unit SBCUAAP R-EBS SL RST Electronic Business Set (P-Phone) SBLSNH8 OCU-DP Office Channel Unit Data Port (56KB) SBUIAF5 ES10/100 10/100 ETHERNET INTERFACE SFP 100BASE-FX SFP 100BASE-LX10 optics SFP 100BASE-T Copper Page 20 of 20