Escenarios de VoIP con Routers Cisco
|
|
|
- Bonnie Bates
- 8 years ago
- Views:
Transcription
1 Escenarios de VoIP con Routers Cisco Edgar Velarde
2 Escenario FXS1 FXS2 Central FXo1 201 (2) R1700 2FXS+ 2FXO R1 R2 R3 R4 Fa0 Fa0 Fa1 Fa0 Fa1 Fa / / / Loopback /32 Dial-peer voip A Dial-peer voip B Remoto R2600 2FXS Loopback /32 FXS1 FXS2 (1) PBX Panasonic Un usuario en el sitio Remoto levanta el teléfono 1000 (1) y su puerto FXS1 disca los dígitos 201 automáticamente para enrutar la llamada hacia la PBX (2) ubicada en la sede Central.
3 Configuración Parte 1/2 Configurando el router R1 (1700) Router(config-if)#ip address mask Router(config)#interface loopback 0 Router(config-if)#ip address *** Configurando los dial-peer POTS para cada puerto FXS Router(config)#dial-peer voice 1 pots Router(config-dial-peer)#destination pattern 3020 Router(config-dial-peer)#port 0/0/0 Router(config)#dial-peer voice 2 pots Router(config-dial-peer)#destination pattern 3030 Router(config-dial-peer)#port 0/0/1 *** Configurando el dial-peer POTS del puerto FXO Router(config)#dial-peer voice 3 pots Router(config-dial-peer)#destination pattern 201 Router(config-dial-peer)#port 1/0 *** Configurando el voice port FX0 Router(config)#voice port 1/0 Router(config-dial-port)#signal loop-start Router(config-dial-port)#cptone PE Router(config-dial-port)#no shutdown Router(config-dial-port)#exit *** Configurando el dial-peer voip A Router(config)#dial-peer voice 1000 voip Router(config-dial-peer)#destination-pattern 1... Router(config-dial-peer)#session target ipv4: Router(config)#ip route Router(config)#ip route Router(config)#ip route Configurando el router R2 Router(config-if)#ip address mask Router(config)#interface fastethernet 0/1 Router(config-if)#ip address mask Router(config)#ip route Router(config)#ip route Router(config)#ip route
4 Configuración Parte 2/2 Configurando el router R3 Router(config-if)#ip address mask Router(config)#interface fastethernet 0/1 Router(config-if)#ip address mask Router(config)#ip route Router(config)#ip route Router(config)#ip route Configurando el router R4 (2600) Router(config-if)#ip address mask Router(config)#interface loopback 0 Router(config-if)#ip address *** Configurando los dial-peer POTS para cada puerto FXS Router(config)#dial-peer voice 1 pots Router(config-dial-peer)#destination pattern 1000 Router(config-dial-peer)#port 0/0/0 *** Configurando el voice port FXS1 Router(config)#voice port 0/0/0 Router(config-dial-port)#cptone PE Router(config-dial-port)#connection plar 1000 Router(config-dial-port)# no shutdown Router(config-dial-port)#exit Router(config)#dial-peer voice 2 pots Router(config-dial-peer)#destination pattern 1001 Router(config-dial-peer)#port 0/0/1 *** Configurando el dial-peer voip B Router(config)#dial-peer voice 1000 voip Router(config-dial-peer)#destination-pattern 30.. Router(config-dial-peer)#session target ipv4:2.2.2 Router(config)#dial-peer voice 1001 voip Router(config-dial-peer)#destination-pattern 2.. Router(config-dial-peer)#session target ipv4:2.2.2
5 Escenario 2 (1) Remoto Dial-peer voip A Central FXS1 FXS2 FXS3 R R1 S /30 S0 S /30 S Fa /30 Fa0 Fa /30 Fa0 R Fa /30 Fa0 PBX Panasonic R1700 FX <port 1> 1003 FXS4 Loopback /32 Dial-peer voip B Loopback / (2) Un usuario de la sede Central levanta la extensión 101 (2) con la intención de llamar a la extensión 1000 (1) en la sede Remoto.
6 Configuración Parte 1/3 Configurando el router 2600 *** Averiguando los puertos FXS del router Router#show running-config Building configuration... voice-port 1/0/0 voice-port 1/0/1 voice-port 1/1/0 voice-port 1/1/1 end Router(config-if)#ip address mask Router(config)#interface serial 0/0/0 Router(config-if)#ip address Router(config)#interface loopback 0 Router(config-if)#ip address *** Configurando los dial-peer POTS para cada puerto FXS Router(config)#dial-peer voice 10 pots Router(config-dial-peer)#destination pattern 1000 Router(config-dial-peer)#port 1/0/0 Router(config)#dial-peer voice 11 pots Router(config-dial-peer)#destination pattern 1001 Router(config-dial-peer)#port 1/0/1 Router(config)#dial-peer voice 12 pots Router(config-dial-peer)#destination pattern 1002 Router(config-dial-peer)#port 1/1/0 Router(config)#dial-peer voice 13 pots Router(config-dial-peer)#destination pattern 1003 Router(config-dial-peer)#port 1/1/1 Router(config)#exit *** Salvando configuración Router#rw *** Configurando el dial-peer voip A Router(config)#dial-peer voice 1000 voip Router(config-dial-peer)#destination-pattern 2.. Router(config-dial-peer)#session target ipv4:
7 Configuración Parte 2/3 Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#exit Configurando el router R1 Router(config-if)#ip address mask Router(config)#interface fastethernet 0/1 Router(config-if)#ip address mask Router(config)#interface serial 0/0/0 Router(config-if)#ip address Router(config)#interface serial 0/0/1 Router(config-if)#ip address Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#exit Configurando el router R2 Router(config-if)#ip address mask Router(config)#interface fastethernet 0/1 Router(config-if)#ip address mask Router(config)#interface serial 0/0/0 Router(config-if)#ip address Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route
8 Configuración Parte 3/3 Configurando router 1700 Router(config-if)#ip address mask Router(config)#interface loopback 0 Router(config-if)#ip address *** Configurando el dial-peer POTS del puerto FXO Router(config)#dial-peer voice 1 pots Router(config-dial-peer)#destination pattern 201 Router(config-dial-peer)#port 1/0 *** Configurando el voice port FXO Router(config)#voice port 1/0 Router(config-dial-port)#signal loop-start Router(config-dial-port)#cptone PE Router(config-dial-port)#connection plar 1000 Router(config-dial-port)# no shutdown Router(config-dial-port)#exit *** Configurando el dial-peer voip B Router(config)#dial-peer voice 1000 voip Router(config-dial-peer)#destination-pattern 1... Router(config-dial-peer)#session target ipv4: Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#ip route Router(config)#exit
Configuring Voice over IP
CHAPTER 4 This chapter explains how to configure voice interfaces and ports, which convert telephone voice signals for transmission over an IP network. This chapter presents the following major topics:
VoIP Configuration Examples
APPENDIX C This section uses four different scenarios to demonstrate how to configure Voice over IP (VoIP). The actual VoIP configuration procedure depends on the topology of your voice network. The following
Curso de Telefonía IP para el MTC. Sesión 4-1 Tipos de llamadas. Mg. Antonio Ocampo Zúñiga
Curso de Telefonía IP para el MTC Sesión 4-1 Tipos de llamadas Mg. Antonio Ocampo Zúñiga Call Types Local: Does not traverse the WAN or PSTN. On-net: Occurs between two telephones on the same data network.
Session Title: Exploring Packet Tracer v5.3 IP Telephony & CME. Scenario
Session Title: Exploring Packet Tracer v5.3 IP Telephony & CME Scenario With the scheduled release of Packet Tracer v5.3 in the near future, this case study is designed to provide you with an insight into
CVOICE Exam Topics Cisco Voice over IP Exam #642-432 7/14/2005
CVOICE Exam Topics Cisco Voice over IP Exam #642-432 7/14/2005 From the Cisco CVOICE 642-432 Exam Topics Voice over IP Technologies Describe the similarities and differences between PSTN and VoIP including
Dial Peer Configuration Examples
Dial Peer Configuration Examples This appendix contains a series of configuration examples featuring the minimum required components and critical Cisco IOS command lines extracted from voice gateway configuration
VoIP Lab: Cisco CallManager Express, Temporary Work Instructions
1 VoIP Lab: Cisco CallManager Express, Temporary Work Instructions Contents Temporary Solution 2 Objectives 2 Theoretical Background 2 Prerequisite 2 Task 1. Setting up Basic IP Telephony System 2 Cisco
642-436 Q&A. DEMO Version
Cisco Voice over IP (CVOICE) Q&A DEMO Version Copyright (c) 2010 Chinatag LLC. All rights reserved. Important Note Please Read Carefully For demonstration purpose only, this free version Chinatag study
Direct Inward Dial Digit Translation Service
Direct Inward Dial Digit Translation Service In Cisco CME 3.2.3 and later versions, a Tcl script is available to provide digit translation for Direct Inward Dial (DID) calls when the DID digits provided
Cisco 3640 - PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with CallManager using Analog FXS and FXO Interfaces as an MGCP Gateway
Application Note Cisco 3640 - PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with CallManager using Analog FXS and FXO Interfaces as an MGCP Gateway Introduction This application note describes
Special-Purpose Connections
Special-Purpose Connections Connection Commands This topic identifies different special-purpose connection commands. Special-Purpose Connection Commands connection plar Associates a voice port directly
LAB MANUAL for Computer Network
LAB MANUAL for Computer Network CSE-310 F Computer Network Lab L T P - - 3 Class Work : 25 Marks Exam : 25 MARKS Total : 50 Marks This course provides students with hands on training regarding the design,
System Components PBX Model. Configuration Tasks
Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 3600 series voice gateway with a Lucent
Case Study 1: Registering IP Phones with a remote Call
Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular
Configuring Voice over IP for Cisco MC3810 Series Concentrators
Configuring Voice over IP for Cisco MC3810 Series Concentrators Feature Summary Voice over IP (VoIP) enables a Cisco MC3810 concentrator to carry voice traffic (for example, telephone calls and faxes)
Internet Telephony PBX System
Internet Telephony PBX System GSM Gateway PSTN call busy forward to GSM Configuration Copyright PLANET Technology Corporation. All rights reserved. Case 32: PSTN call busy forward to GSM Configuration
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.
Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability
VoIP Configuration. Prerequisite Tasks CHAPTER
CHAPTER 2 VoIP Configuration This chapter explains how to configure VoIP on your router and contains the following sections: Prerequisite Tasks Configuration Tasks Configure IP Networks for Real-Time Voice
Configuring a Router
CHAPTER 3 Configuring a Router This chapter provides information and commands concerning the following topics: Configuring a router, specifically: Names Passwords Interfaces MOTD banners IP host tables
Cisco Voice Gateways. PacNOG6 VoIP Workshop Nadi, Fiji. November 2009. Jonny Martin - jonny@jonnynet.net
Cisco Voice Gateways PacNOG6 VoIP Workshop Nadi, Fiji. November 2009 Jonny Martin - jonny@jonnynet.net Voice Gateways Any device with one or more TDM PSTN interfaces on them TDM - Time Division Multiplexing
Voice Dial Plans, Configuring Voice Interfaces and Dial Peers
Voice Dial Plans, Configuring Voice Interfaces and Dial Peers Cisco Networking Academy Program 1 Call Establishment Principles 2 Dial-Peer Call Legs 3 End-to-End Calls 4 Configuring Dial Peers 5 Understanding
Peer-to-Peer SIP Mode with FXS and FXO Gateways
Peer-to-Peer SIP Mode with FXS and FXO Gateways New Rock s SIP based VoIP gateways with FXS and FXO ports support peer-to-peer mode which has many applications in deploying enterprise multi-site telephone
Call Setup and Digit Manipulation
Call Setup and Digit Manipulation End-to-End Calls This topic explains how routers interpret call legs to establish end-to-end calls. End-to-End Calls IP Telephony 2005 Cisco Systems, Inc. All rights reserved.
Configuring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
NAT (Network Address Translation) & PAT (Port Address Translation)
NAT (Network Address Translation) & PAT (Port Address Translation) First let s define NAT terms: Inside local address The IP address assigned to a host on the inside network. The address is usually not
Voice over IP Quick Start Guide
Customer Order Number: DOC-VOICEOIP-QSG= Text Part Number: 78-4936-01 Voice over IP Quick Start Guide Product Numbers: NM-1V=, NM-2V= VIC-2E/M=, VIC-2FXO=, VIC-2FXS= The voice over IP feature enables Cisco
How-To Configure NetFlow v5 & v9 on Cisco Routers
How-To Configure NetFlow v5 & v9 on Cisco Routers Share: Visibility into the network is an indispensable tool for network administrators. Network visibility can be achieved through daily troubleshooting,
SIP Internet Telephony Gateway
SIP Internet Telephony Gateway VIP - 2 / 4 / 8 / 16 / 24 Series Peer-to-Peer Quick Configuration for VIP-450 Copyright PLANET Technology Corporation. All rights reserved. Scenarios explain: Peer-to-Peer
Cisco VoIP CME Labs by Michael T. Durham
Cisco VoIP CME Labs by Michael T. Durham Welcome to NetCertLabs CCNA Voice Lab series. In this lab we will be bringing a little sound to our callers on hold. By having MoH (Music on Hold) enabled on your
Cisco 1751 Voice-over-IP Quick Start Guide
The Cisco 1751 Voice over IP Quick Start Guide explains how to install WAN Interface Cards and Voice Interface Cards, how to run configuration tools, and how to perform essential Voice-over-IP (VoIP) configuration
Laboratorio 3 Comunicación sincrónica Vía Satélite
Laboratorio 3 Comunicación sincrónica Vía Satélite Esquema de la Red WAN 192.168.0.0 /30 192.168.0.1 Router 1 Router 2 10.0.1.1 192.168.0.1 10.0.2.1 Ethernet Ethernet 10.0.1.20 LAN 1 10.0.1.0 /24 LAN 2
Configuring Network Side ISDN PRI Signaling, Trunking, and Switching
Configuring Network Side ISDN PRI Signaling, Trunking, and Switching This chapter describes the Network Side ISDN PRI Signaling, Trunking, and Switching feature. The following main sections are provided:
Configuring 1- and 2-Port T1/E1 Multiflex Voice/WAN Interface Cards on Cisco 2600 and 3600 Series Routers
Configuring 1- and 2-Port T1/E1 Multiflex Voice/WAN Interface Cards on Cisco 2600 and 3600 Series Routers This document explains how you can configure 1- and 2-port T1 and E1 Multiflex Voice/WAN interface
This topic describes dial peers and their applications.
Dial Peers What is Dial Peer? This topic describes dial peers and their applications. What is a Dial Peer? A dial peer is an addressable call endpoint. Dial peers establish logical connections, called
3.1 Connecting to a Router and Basic Configuration
3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console
Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router
Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue este capítulo Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue el libro completo
Application Note: Patton SmartNode VoIP Gateways for 3CX Phone System
Application Note: Patton SmartNode VoIP Gateways for 3CX Phone System Introduction In installing 3CX Phone System for Windows, you will likely need to integrate existing legacy telephony equipment, fax
Blue Coat Systems. Reference Guide. WCCP Reference Guide. For SGOS 5.3
Blue Coat Systems Reference Guide WCCP Reference Guide For SGOS 5.3 Contact Information Blue Coat Systems Inc. 420 North Mary Ave Sunnyvale, CA 94085-4121 http://www.bluecoat.com/support/contact.html bcs.info@bluecoat.com
System Components PBX Model. Configuration Tasks
Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with E1 R2 Signaling This document describes the interoperability and configuration of a Cisco3600 series voice gateway with a Lucent
Network Scenarios Pagina 1 di 35
Network Scenarios Pagina 1 di 35 Table of Contents Network Scenarios Cisco 827 s Network Connections Internet Access Scenarios Before You Configure Your Internet Access Network Replacing a Bridge or Modem
LAB Configuring NAT. Objective. Background/Preparation
LAB Configuring NAT Objective Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. Configure static
Cisco ISDN PRI to SIP Gateway
Cisco ISDN PRI to SIP Gateway Supported features Full ISDN E1 emulation Early media support Inbound calling. Type SIP REGISTERED TRUNK Outbound Calling ISDN PRI equivalent Secure Calling via SIP Encrypt
Avaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0
Avaya Solution & Interoperability Test Lab Avaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0 Abstract Avaya one-x Quick Edition R3.1 provides
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP
Lab 8.3.3b Configuring a Remote Router Using SSH
Lab 8.3.3b Configuring a Remote Router Using SSH Objectives Use SDM to configure a router to accept SSH connections. Configure SSH client software on a PC. Establish a connection to a Cisco ISR using SSH
PBX Setup Basic setup procedures
Basic setup procedures 1) Configure the SpoTel PBX & Voip phones to a router/switch 2) Setup Extensions on SpoTel PBX -> Testing: Call between Extension phones 3) Setup Trunks on Spotel PBX 4) Setup Outbound
AMC + configuración clientes. Neris/A400
AMC + configuración clientes Neris/A400 Aastra - 2010 Requisitos Para la instalación será necesario tener en cuenta lo siguiente: Licencias Usuario SIP: por cada cliente AMC+. Trunking SIP: recomendable
Propiedades del esquema del Documento XML de envío:
Web Services Envio y Respuesta DIPS Courier Tipo Operación: 122-DIPS CURRIER/NORMAL 123-DIPS CURRIER/ANTICIP Los datos a considerar para el Servicio Web DIN que se encuentra en aduana son los siguientes:
How to Configure Cisco 2600 Routers
Helsinki University of Technology Department of Communications and Networking How to Configure Cisco 2600 Routers Juha Järvinen 10.6.2004 Juha.Jarvinen@netlab.hut.fi Modified by Zhong Yunqiu 7.8.2008 Table
Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323
Application Note Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323 Table of Contents Introduction...1 Network Topology...2 Limitations...2 Hardware
Configuring Voice over IP
Configuring Voice over IP This chapter provides an overview of Voice over IP (VoIP) technology and gives step-by-step configuration tasks. The chapter contains the following sections: VoIP Benefits, page
Building a Scalable Numbering Plan
Building a Scalable Numbering Plan Scalable Numbering Plan This topic describes the need for a scalable numbering plan in a VoIP network. Dial Plans Dial plans contain specific dialing patterns for a user
Let's take a look at another example, which is based on the following diagram:
Chapter 3 - Voice Dial Peers In order to understand the concept of dial peers, it is important to understand call legs. A voice call over a packet network is segmented into discrete call legs. A call leg
Lab: Basic Router Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Def. Gateway R1 Fa0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 192.168.2.1 255.255.255.0 N/A R2 Fa0/0 192.168.3.1 255.255.255.0 N/A
This chapter covers the following topics: IP phones and lines Shared lines Hunt groups Intercoms Paging Line overlays Call pickup Softkey
This chapter covers the following topics: IP phones and lines Shared lines Hunt groups Intercoms Paging Line overlays Call pickup Softkey customization Call transfer and forward C H A P T E R 5 Cisco CME
Network Traffic Analyzer
Network Traffic Analyzer Configuring NetFlow or sflow on Network Devices Revision 1.2.9 - (11-03-2015)!1 Introduction This document explains how to configure network devices such as Switches to send NetFlow
SmartPTT Tutorial Telephone Interconnect
SmartPTT Tutorial Telephone Interconnect Telephone Interconnect Overview Telephone Interconnect is the service included into SmartPTT Radioserver to establish interconnection between Radio and Telephone
ICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by
ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500
Blue Coat Systems. Reference Guide. WCCP Reference Guide. For SGOS 5.5-6.2
Blue Coat Systems Reference Guide WCCP Reference Guide For SGOS 5.5-6.2 Contact Information Americas: Blue Coat Systems Inc. 410 North Mary Ave Sunnyvale, CA 94085-4121 Rest of the World: Blue Coat Systems
VoIP Gateway/IP-PBX Interworking with Skype
VoIP Gateway/IP-PBX Interworking with Skype IPNext50 IP-PBX IPNext20 IP-PBX AP100B VoIP Gateway AddPac Technology 2010, Sales and Marketing www.addpac.com Contents Skype Interworking Test VoIP Gateway
Lab 4.2.4 Advanced Telnet Operations
Lab 4.2.4 Advanced Telnet Operations Objective Use the telnet command to remotely access other routers. Verify that the application layer between the source and the destination is working properly. Suspend
Routing Protocols and Concepts Chapter 2 Conceitos de protocolos de Encaminhamento Cap 2
Static Routing Routing Protocols and Concepts Chapter 2 1 1 Objectives Define the general role a router plays in networks. Describe the directly connected networks, different router interfaces Examine
Table of Contents. Cisco Mapping Outbound VoIP Calls to Specific Digital Voice Ports
Table of Contents Mapping Outbound VoIP Calls to Specific Digital Voice Ports...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...2 Network Diagram...2
for SS7 VoIP Gateways
Smart Web Manager for SS7 VoIP Gateways www.addpac.com AddPac Technology 2013, Sales and Marketing Contents SS7 VoIP Gateway Service Diagram SS7 VoIP Gateway Main Features SS7 VoIP Gateway Features SS7
Lab 5.3.9b Managing Router Configuration Files Using TFTP
Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.
Direct IP Calls. Quick IP Call Mode
Unicorn3112 Tips Direct IP Calls...1 Quick IP Call Mode...1 PSTN Pass Through...2 VoIP-to-PSTN Calls...2 PSTN-to-VoIP Calls...3 Route Calls to PSTN...4 Forward Calls to PSTN...4 Forward Calls to VoIP...4
Lab 1.2.3 Review of Basic Router Configuration with RIP. Objective. Background / Preparation. General Configuration Tips
Lab 1.2.3 Review of Basic Router Configuration with RIP Objective Cable and configure workstations and routers Setup IP addressing scheme using Class B networks Configure Routing Information Protocol (RIP)
- Basic Voice over IP -
1 Voice over IP (VoIP) - Basic Voice over IP - Voice over IP (VoIP) is a digital form of transport for voice transmissions, replacing analog phone systems. The benefits of VoIP are considerable: Better
VLSM Static routing. Computer networks. Seminar 5
VLSM Static routing Computer networks Seminar 5 IP address (network and host part) Address classes identified by first three bits Subnet mask determines how the IP address is divided into network and host
IST 220 Honors Project. Subnets with Variable Length Subnet Masks
IST 220 Honors Project Subnets with Variable Length Subnet Masks Project Objectives: In this project, you will subnet the IP address 193.170.10.0 according to needs of the organization. Overview a) Perform
Cisco IOS SIP Configuration Guide
Cisco IOS SIP Configuration Guide Dialpeer Configuration Session Number 1 Terminology Call - A connection terminating on or passing through a gateway. Call Leg - The segment of a call associated with a
Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram
Felix Rohrer PT Activity 7.5.3: Troubleshooting Wireless WRT300N Topology Diagram All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
AT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy
INTERACTIVE INTELLIGENCE AT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy Version 1.7 9/2/2009 TABLE OF CONTENTS 1 AT&T... 5 1.1 Introduction... 5 1.2 Product Descriptions...
Configuring Fax Pass-Through
Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an
Applicazioni Telematiche
Angelo Coiro Laboratorio Applicazioni Telematiche L emulatore Packet Tracer Packet Tracer Cisco Packet Tracer is an academic software that allows to emulate Cisco devices Packet Tracer can be used for
Dial Peer. Example: Dial-Peer Configuration
Configuring Dial Peers Understanding Dial Peers This topic describes dial peers and their applications. Understanding Dial Peers A dial peer is an addressable call endpoint. Dial peers establish logical
VoIP Signaling and Call Control
VoIP Signaling and Call Control Cisco Networking Academy Program 1 Need for Signaling and Call Control 2 Model for VoIP Signaling and Call Control VoIP signaling components Endpoints Common control Common
FXO, FXS, and E&M Voice Interface Card Support on Cisco 1700 Series Routers
FXO, FXS, and E&M Voice Interface Card Support on Cisco 1700 Series Routers This document describes the support on the Cisco 1751 and Cisco 1760 routers for the following new voice interface cards (VICs):
Supporting Multiple PBXs in Hybrid Deployment Models
NetVanta Unified Communications Technical Note Supporting Multiple PBXs in Hybrid Deployment Models Application Note for Hybrid Deployments The goal of this technical note is to ensure that you can leverage
Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.
Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A
Lab 7.2.9 Load Balancing Across Multiple Paths
Lab 7.2.9 Load Balancing Across Multiple Paths Objective Configure Load balance across multiple paths. Observe the load balancing process. Background/Preparation Cable a network similar to the one in the
IP Telephony: Review and Implementation
IP Telephony: Review and Implementation by Agul Kaul This project report is submitted to the Department of Electrical Engineering and Computer Science and the Faculty of the Graduate School of the University
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Objective This lab may introduce new CCNP lab equipment and certain IOS features. This introductory activity also describes how to
Building a Network in GNS3
Building a Network in GNS3 In this tutorial, you will create a network in GNS3 between two routers, and each router will have one host connected to it. The ultimate goal is to route data between network
CCNA Access List Sim
1 P a g e CCNA Access List Sim Question An administrator is trying to ping and telnet from Switch to Router with the results shown below: Switch> Switch> ping 10.4.4.3 Type escape sequence to abort. Sending
Netflow Gamme de Produits Netflow, ntop, nprobe, Nbar NetFlow Analyzer Solarwinds Cisco NetFlow Orion Netflow Traffic Analyzer Intégration avec Orion NPM 2 K à 12 K Live Demo: http://npmv7.solarwinds.net/login.asp
Curso de Telefonía IP para el MTC. Sesión 5-1 Implementación de Gateways SIP. Mg. Antonio Ocampo Zúñiga
Curso de Telefonía IP para el MTC Sesión 5-1 Implementación de Gateways SIP Mg. Antonio Ocampo Zúñiga SIP Fundamentals SIP is a simple extensible protocol. SIP is defined in IETF RFC 2543 and RFC 3261.
IOS NAT Load Balancing for Two ISP Connections
IOS NAT Load Balancing for Two ISP Connections Document ID: 100658 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot
Configuring Voice and Data Support on VWIC3s
First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following
Enhanced Voice Services for Japan for Cisco 800 Series Routers
Enhanced Voice Services for Japan for Cisco 800 Series Routers This appendix describes the Enhanced Voice Services for Japan Cisco IOS features, including INS-NET-64 voice features. This appendix includes
Configuring Positron s V114 as a VoIP gateway for a 3cx system
Assumptions: Configuring Positron s V114 as a VoIP gateway for a 3cx system The IP address of the V114 is 192.168.1.2 The IP address of the 3CX PBX System is 192.168.1.110 3CX already has some IP phones
Configuring VoIP Call Setup Monitoring
The Cisco IOS IP Service Level Agreements (SLAs) VoIP Call Setup (Post-Dial Delay) Monitoring feature provides the ability to measure your network s response time for setting up a Voice over IP (VoIP)
Expert Reference Series of White Papers. Cisco Service Provider Next Generation Networks
Expert Reference Series of White Papers Cisco Service Provider Next Generation Networks 1-800-COURSES www.globalknowledge.com Cisco Service Provider Next Generation Networks Johnny Bass, Senior Global
NetVanta 7100 Exercise Service Provider SIP Trunk
NetVanta 7100 Exercise Service Provider SIP Trunk PSTN NetVanta 7100 FXS 0/1 x2001 SIP Eth 0/0 x2004 SIP Server 172.23.102.87 Hosted by x2003 www.voxitas.com In this exercise, you will create a SIP trunk
Expert Reference Series of White Papers. Cisco Service Provider Next Generation Networks
Expert Reference Series of White Papers Cisco Service Provider Next Generation Networks 1-800-COURSES www.globalknowledge.com Cisco Service Provider Next Generation Networks Johnny Bass - Senior Global
Laboratorio 4. Comunicación sincrónica Vía Satélite
Laboratorio 4 Comunicación sincrónica Vía Satélite Esquema de la Red WAN 192.168.0.0 /30 192.168.0.1 Router 1 Router 2 10.0.1.1 192.168.0.1 10.0.2.1 Ethernet Ethernet 10.0.1.20 LAN 1 10.0.1.0 /24 LAN 2
PATTON TECH NOTES What are FXS and FXO?
Introduction The question What is the difference between FXS and FXO? is frequently asked by those deploying Patton Voice-over-Internet Protocol (VoIP) SmartNode solutions. Foreign exchange Subscriber
640-460 - Implementing Cisco IOS Unified Communications (IIUC)
640-460 - Implementing Cisco IOS Unified Communications (IIUC) Course Introduction Course Introduction Module 1 - Cisco Unified Communications System Introduction Cisco Unified Communications System Introduction
Experts in Networking. CCNA Cheat Sheet. This CCNA command cheat sheet covers both ICND parts 1 & 2 and covers the current CCNA exam (640-802).
CCNA Cheat Sheet This CCNA command cheat sheet covers both ICND parts 1 & 2 and covers the current CCNA exam (640-802). Whilst not an exhaustive IOS command list it covers the majority of commands found
Aire-6 Acceso Inalámbrico a Redes IPV6. Christian Lazo R. Universidad Austral de Chile
Aire-6 Acceso Inalámbrico a Redes IPV6 Christian Lazo R. Universidad Austral de Chile Proyecto Frida 2004 Objetivos HOT SPOT IPv6 NATIVO IPv6 + WiFI E2E, Always On, Movilidad AAAC (Authentication, Authorization,