Network Traffic Analyzer

Size: px

Start display at page:

Download "Network Traffic Analyzer"

Madlyn May
8 years ago
Views:

1 Network Traffic Analyzer Configuring NetFlow or sflow on Network Devices Revision ( )!1

2 Introduction This document explains how to configure network devices such as Switches to send NetFlow or sflow statistics to a Monitoring Server like BLËSK. Please take a note that commands as explained into this document may vary according to your device version and models. Enable & Export NetFlow on Cisco IOS Device To ensure that the necessary hardware is enabled, issue the show module command, as follows: show module all Mod Submodule Model Serial No. Hw Status Netflow Services Card WS-F4531 JAB062209CG 0.2 Ok If the NetFlow module is available, you should see something like the above. The following sequence of IOS commands can be used as a model for configuring NetFlow. router#enable Password:***** router#configure terminal router-2621(config)#interface FastEthernet 0/1 router-2621(config-if)#ip route-cache flow router-2621(config-if)#exit router-2621(config)#ip flow-export destination x.x.x.x 6343 router-2621(config)#ip flow-export source FastEthernet 0/1 router-2621(config)#ip flow-export version 5 router-2621(config)#ip flow-cache timeout active 1 router-2621(config)#ip flow-cache timeout inactive 15 router-2621(config)#snmp-server ifindex persist router-2621(config)#^z router#write In the above example, the ip flow-export destination x.x.x.x is the IP address of the BLËSK monitoring server. The 6343 in the ip flow-export destination command example corresponds to the Local Collector UDP Port number configured for the NetFlow plugin. The flow export source interface will vary, depending on the interface providing the source traffic.!2

Enable & Export NetFlow on Cisco IOS Device To ensure that the necessary hardware is enabled, issue the show module command, as follows: show module all Mod Submodule Model Serial No.

3 Enable & Export sflow on Brocade Device The following configuration enables sflow monitoring of all interfaces on a Brocade FGS switch, sampling packets at 1-in-10, polling counters every 20 seconds and sending the sflow to an analyzer ( ) on UDP port 6343 (the default sflow port): fgs(config)# int e 0/1/1 to 0/1/24 fgs(config-mif-0/1/1-0/1/24)# sflow forwarding fgs(config-mif-0/1/1-0/1/24)# exit fgs(config)# sflow destination fgs(config)# sflow sample 10 fgs(config)# sflow polling-interval 20 fgs(config)# sflow enable Enable & Export sflow on HP Device The commands bellow only works on the 3500/5400/8200/6200 HP products. 1. Configure a destination: hp (config)# sflow 2 destination x.x.x.x 6343 The above commands will send sflow to the destination IP x.x.x.x which is the one used by BLËSK. 2. Enable sample rate and polling interval: hp (config)# sflow 2 sampling all 10 hp (config)# sflow 2 polling all 20 You can enable sample rate and polling interval depending of the accuracy of the received packet that you want to get. Use the all parameter in sampling and polling parameters to enable sflow on all interfaces. Enable & Export sflow on DELL Device 1. Configure a destination: dell (config)# sflow 1 destination x.x.x.x dell (config)# sflow 1 destination owner <owner_name> timeout The above commands will send sflow to the destination IP x.x.x.x which is the one used by BLESK. 2. Enable sample rate and polling interval: dell (config)# sflow 1 sampling ethernet 1/g1-1/g dell (config)# sflow 1 polling ethernet 1/g1-1/g32 20 The above configure the sampling packets at 1-in-1024, and polling counters every 20 seconds.!3

0.0.5) on UDP port 6343 (the default sflow port): fgs(config)# int e 0/1/1 to 0/1/24 fgs(config-mif-0/1/1-0/1/24)# sflow forwarding fgs(config-mif-0/1/1-0/1/24)# exit fgs(config)# sflow destination 10.

4 Enable & Export sflow on a Force 10 Device 1. The following commands configure a Force10 switch ( ), sampling packets at 1-in-512, polling counters every 30 seconds and sending the sflow to an analyzer ( ) over UDP using the default sflow port (6343): config> sflow collector agent-addr config> sflow sample-rate 512 config> sflow polling 30 config> sflow enable 2. Then for each interface: interface> sflow enable 3. You can also use the following command to list the configuration settings: show sflow Enable & Export sflow on FortiGate appliances The recent FortiOS 4.0 MR2 release adds sflow support to Fortinet's FortiGate appliances. The following commands configure a FortiGate to sample packets at 1-in-10, poll counters every 20 seconds, and send sflow to an analyzer ( ) over UDP using the default sflow port (6343): config system sflow set collectorip set collectorport 6343 end Then for each interface: config sys interface edit set sflow-sampler enable set sample-rate 10 set sample-direction both set polling-interval 20 next end Configure sflow monitoring on all interfaces on the switch for full visibility. Packet sampling is implemented in hardware so all the interfaces can be monitored with very little overhead.!4

Then for each interface: interface> sflow enable 3.

5 Changing the Polling Interval The polling interval defines how often sflow byte and packet counter data for a port are sent to the sflow collector(s). If multiple ports are enabled for sflow, the switch device staggers transmission of the counter data to smooth performance. For example, if sflow is enabled on two ports and the polling interval is 20 seconds, the switch device sends counter data every ten seconds. The counter data for one of the ports are sent after ten seconds, and counter data for the other port are sent after an additional ten seconds. Ten seconds later, new counter data for the first port are sent. Similarly, if sflow is enabled on five ports and the polling interval is 20 seconds, the device sends counter data every four seconds. The default polling interval is 20 seconds. You can change the interval to a value from 1 to any higher value. The interval value applies to all interfaces on which sflow is enabled. If you set the polling interval to 0, counter data sampling is disabled. Changing the Sampling Rate The sampling rate is the average ratio of the number of packets incoming on an sflow-enabled port, to the number of flow samples taken from those packets. You can change the default (global) sampling rate. You also can change the rate on an individual port, overriding the default sampling rate of 512. With a sampling rate of 512, on average, one in every 512 packets forwarded on an interface is sampled. Configuration Considerations The sampling rate is a fraction in the form 1/N, meaning that, on average, one out of every N packets will be sampled. The sflow sample command at the global level or port level specifies N, the denominator of the fraction. Thus a higher number for the denominator means a lower sampling rate since fewer packets are sampled. Likewise, a lower number for the denominator means a higher sampling rate because more packets are sampled. For example, if you change the denominator from 512 to 128, the sampling rate increases because four times as many packets will be sampled. The software rounds the value you enter to the next higher odd power of 2. This value becomes the actual default sampling rate and is one of the following For example, if the configured sampling rate is 1000, then the actual rate is 2048 and 1 in 2048 packets are sampled by the hardware.!5

For example, if sflow is enabled on two ports and the polling interval is 20 seconds, the switch device sends counter data every ten seconds.

How-To Configure NetFlow v5 & v9 on Cisco Routers

How-To Configure NetFlow v5 & v9 on Cisco Routers Share: Visibility into the network is an indispensable tool for network administrators. Network visibility can be achieved through daily troubleshooting,