SECTION STAINLESS STEEL COLUMN COVER REVEAL JOINT SYSTEM

Transcription

1 AMERICLAD AC-10ST MANUFACTURER: Quality Metalcrafts, LLC Commerce Blvd. Rogers, MN Telephone: (866) Fax: (763) AMERICLAD AC-10ST Column Cover Reveal Joint SECTION STAINLESS STEEL COLUMN COVER REVEAL JOINT SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The drawings and provisions of the General Conditions, and the sections included under Division 1 specification sections, apply to this section 1.2 SUMMARY A. This section includes stainless steel column covers that are used as the exterior and interior cladding 1.3 PERFORMANCE REQUIREMENTS A. Structural Performance: provide column cover assemblies capable of withstanding the effects of load and stresses from wind loads, dead loads, snow loads and normal and expected thermal movement without evidence of permanent defects of the assemblies. System design for a mechanically fastened assembly to substructure 1. Dead Load as required by applicable building code 2. Live Load as required by applicable building code 3. Wind Load: uniform pressure (define velocity pressure) of (insert design criteria) pound/square foot, acting inward and outward. 4. Thermal Movements: provide column assemblies that allow for thermal movements to prevent buckling, opening of joints and other thermal effects 1 Copyright 2010 Quality Metalcrafts, LLC

2 AMERICLAD AC-10ST B. Design the column cover for a mechanically fastened assembly to substructure C. Design column cover tolerances to manufacturer s standard tolerances D. Column cover to have a maximum allowable deflection of L/180 E. Column cover joints will be sealed appropriately using backer rod and approved caulk 1.4 SUBMITTALS A. Product Data: Manufacturer s product literature B. Finish Samples: submit samples for final approval C. Shop Drawings: submit shop drawings showing plans, sections and details 1.5 QUALITY ASSURANCE A. Manufacturer Qualifications: Minimum of five years experience in manufacturing of metal column cover products B. Installer Qualifications: Acceptable to manufacturer C. Engineering Qualifications: Provide engineering calculations for the column cover assembly to be prepared by an engineer registered in the state the project is located 1.6 DELIVERY, STORAGE AND HANDLING A. Delivery: deliver columns in manufacturer s crates packed for long haul transit B. Storage: store materials in a dry and safe area C. Handling: handle materials to avoid any damage to materials and finishes 1.7 WARRANTY A. The contractor must warrant the materials to be free of defects in accordance with the general conditions. PART 2 PRODUCTS 2.1 MANUFACTURER A. Quality Metalcrafts, LLC/AMERICLAD, Commerce Boulevard, Rogers, Minnesota 55374, Telephone: (866) , 1. AC-10ST Stainless Steel Column Cover Reveal Joint System F. Approved equal submitted for approval 10 days prior to bid 2 Copyright 2010 Quality Metalcrafts, LLC

3 AMERICLAD AC-10ST MATERIALS A. Stainless Sheet: ASTM A B. Thickness: 1. Select 16 gauge 2. Select 14 gauge 3. Thicker gauges available, confer with Quality Metalcrafts 2.3 FABRICATION A. Tolerances 1. Panel surfaces shall be free of blemishes, scratches or marks caused during fabrication process 2. Roll columns to a true radius with return attachment legs formed to accommodate proper installation 2.4 ACCESSORIES A. All fasteners shall be stainless steel 2.5 FINISHES A. #4 Brushed Finish B. #8 Mirror Finish C. Textured Metal; confer with Quality Metalcrafts for options PART 3 EXECUTION 3.1 PREPARATION A. Coordinate drawings, diagrams, and instructions for installation 3.2 INSTALLATION A. Install columns plumb and level per shop drawing detailing B. Isolation tape or shim shall be installed where dissimilar materials come in contact 3.3 CLEANING AND PROTECTION A. Clean exposed surfaces after installation per manufacturer s recommendation END OF SECTION 3 Copyright 2010 Quality Metalcrafts, LLC

4 STAINLESS STEEL COLUMN COVER (REVEAL JOINT) D, E, F G, H, J B, C K, L, M R, S, T U, V, W P, Q X, Y, Z A B C D E F G H J K L M RADIUSED - ISOMETRIC RADIUSED - VERTICAL DETAIL (1) RADIUSED - VERTICAL DETAIL (2) RADIUSED - HEAD DETAIL (1) RADIUSED - HEAD DETAIL (2) RADIUSED - HEAD DETAIL (3) RADIUSED - INTERMEDIATE DETAIL (1) RADIUSED - INTERMEDIATE DETAIL (2) RADIUSED - INTERMEDIATE DETAIL (3) RADIUSED - BASE DETAIL (1) RADIUSED - BASE DETAIL (2) RADIUSED - BASE DETAIL (3) N P Q R S T U V W X Y Z RECTANGULAR - ISOMETRIC RECTANGULAR - VERTICAL DETAIL (1) RECTANGULAR - VERTICAL DETAIL (2) RECTANGULAR - HEAD DETAIL (1) RECTANGULAR - HEAD DETAIL (2) RECTANGULAR - HEAD DETAIL (3) RECTANGULAR - INTERMEDIATE DETAIL (1) RECTANGULAR - INTERMEDIATE DETAIL (2) RECTANGULAR - INTERMEDIATE DETAIL (3) RECTANGULAR - BASE DETAIL (1) RECTANGULAR - BASE DETAIL (2) RECTANGULAR - BASE DETAIL (3)

5 ISOMETRIC DETAIL A

6 VERTICAL DETAIL (1) DETAIL B FASTENERS (NOT BY Q.M.) BACKER ROD & SEALANT (NOT BY Q.M.) SHIM (NOT BY Q.M.) FRAMING COMPONENT (NOT BY Q.M.) RADIUS

7 VERTICAL DETAIL (2) DETAIL C FASTENERS (NOT BY Q.M.) STAINLESS STEEL CHANNEL SHIM (NOT BY Q.M.) FRAMING COMPONENT (NOT BY Q.M.) RADIUS

8 HEAD DETAIL (1) DETAIL D CEILING (NOT BY Q.M.) RADIUS

9 HEAD DETAIL (2) DETAIL E CEILING (NOT BY Q.M.) ANGLE ADHERED TO PANEL RADIUS

10 HEAD DETAIL (3) DETAIL F CEILING (NOT BY Q.M.) STAINLESS STEELHEAD ANGLE ADHERED TO PANEL RADIUS

11 INTERMEDIATE DETAIL (1) DETAIL G RADIUS BACKER ROD & SEALANT (NOT BY Q.M.) ANGLE ADHERED TO PANEL.500

12 INTERMEDIATE DETAIL (2) DETAIL H RADIUS FLAT BAR ADHERED TO PANEL FLAT BAR ADHERED TO PANEL FLAT BAR ADHERED TO FLAT BAR

13 INTERMEDIATE DETAIL (3) DETAIL J RADIUS STAINLESS STEEL FLAT TACK WELDED TO PANEL STAINLESS STEEL FLATS TACK WELED TO PANELS

14 BASE DETAIL (1) DETAIL K RADIUS FLOOR (NOT BY Q.M.)

15 BASE DETAIL (2) DETAIL L RADIUS ANGLE ADHERED TO PANEL FLOOR (NOT BY Q.M.)

16 BASE DETAIL (3) DETAIL M RADIUS STAINLESS STEEL BASE ANGLE ADHERED TO PANEL FLOOR (NOT BY Q.M.)

17 ISOMETRIC DETAIL N SQUARE CORNER R1.000 RADIUSED CORNER

18 VERTICAL DETAIL (1) DETAIL P FASTENERS (NOT BY Q.M.) BACKER ROD & SEALANT (NOT BY Q.M.) SHIM (NOT BY Q.M.) FRAMING COMPONENT (NOT BY Q.M.)

19 VERTICAL DETAIL (2) DETAIL Q FASTENERS (NOT BY Q.M.) STAINLESS STEEL CHANNEL SHIM (NOT BY Q.M.) FRAMING COMPONENT (NOT BY Q.M.)

20 HEAD DETAIL (1) DETAIL R CEILING (NOT BY Q.M.)

21 HEAD DETAIL (2) DETAIL S CEILING (NOT BY Q.M.)

22 HEAD DETAIL (3) DETAIL T CEILING (NOT BY Q.M.) STAINLESS STEEL HEAD

23 INTERMEDIATE DETAIL (1) DETAIL U BACKER ROD & SEALANT (NOT BY Q.M.).500

24 INTERMEDIATE DETAIL (2) DETAIL V FLAT BAR ADHERED TO PANEL FLAT BAR ADHERED TO PANEL FLAT BAR ADHERED TO FLAT BAR

25 INTERMEDIATE DETAIL (3) DETAIL W

26 BASE DETAIL (1) DETAIL X FLOOR (NOT BY Q.M.)

27 BASE DETAIL (2) DETAIL Y FLOOR (NOT BY Q.M.)

28 BASE DETAIL (3) DETAIL Z STAINLESS STEEL BASE FLOOR (NOT BY Q.M.)