GLIDER ROCKER. Sand Chair & Ottoman Model # A-002 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

Transcription

1 GLIDER ROCKER Sand Chair & Ottoman Model # A-002 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

2 Safety Precautions Read all instructions before assembly and use of the rocker chair and ottoman. Keep instructions for future use. WARNING ADULT ASSEMBLY REQUIRED: DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE Congratulations on your purchase of the Childcare Glider Rocker Chair and Ottoman. This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. CRUSH AND AMPUTATION HAZARDS: A CHILD S HANDS CAN BE TRAPPED IN MOVING PARTS OF THE ROCKER CHAIR OR OTTOMAN. ALWAYS ENSURE CHILD S HANDS ARE CLEAR FROM MOVING PARTS OF THE ROCKER CHAIR OR OTTOMAN. ENSURE THE FABRIC COVERS OVER THE CHAIR AND OTTOMAN BASES ARE FITTED AT ALL TIMES CARE SHOULD BE TAKEN AS THE UNDERSIDE MECHANISM OF THIS GLIDER COULD PRESENT A HAZARD TO OTHER PEOPLE WHEN IN USE THE FOOTSTOOL IS INTENDED TO BE USED FOR SUPPORTING THE FEET AND LEGS ONLY, NOT FOR SITTING ON DO NOT SIT ON THE EDGE OF THE SEAT, ARMRESTS OR ON THE BACKREST AS THIS COULD CAUSE THE CHAIR TO TIP OVER DO NOT USE THE CHAIR AS A STEP STOOL DO NOT LEAVE CHILDREN UNATTENDED ON OR BESIDE THE GLIDER AND FOOT STOOL Contents Assembly Contents Care Instructions Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product fabrics, colour and design may vary from images shown. CNP Brands reserves the right to alter product specifications without notice as a result of our ongoing policy of product improvement. 3

3 Assembly Contents Check what you have received... You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer Service. In Australia, contact CNP Brands on , in New Zealand contact Wainhouse Distribution on Assembling chair frame 1. Unfold backrest of chair frame. Supplied loose in box: Chair frame Seat cushion 50mm Bolt 45mm Bolt (Dome head) x2 x4 2. Insert T bush into both sides of the hole in the backrest frame. 3. Insert 50mm bolt through the T bush so it is pointing to the outside of the chair. Armrest Pads (L + R) x2 16mm Bolt (Dome head) x4 4. Place plastic spacer onto bolt. Ottoman frame Rocker frame base cover Ottoman cushion Ottoman frame base cover 5. Tighten bolt onto locating tube on armrest using the allen key. Repeat steps 2-5 to assemble other side. WARNING: Ensure screws are secure but not over-tightened. T Bush x4 Allen key (sml) Plastic spacer x2 Allen key (med) 4 5

4 To attach seat cushion Assembling armrests 1. Slide pocket on top rear of seat cushion over the top of the seat frame. 1. Place armrest into position on the seat frame. Ensure the correct armrest is located on the correct side, as indicated by stickers on the frame and armrests. 2. Pull cushion down until it is completely in position. 2. Secure the armrests using 45mm bolts and tighten with allen key. Secure the velcro tabs on the armrests around the bottom bar of the seat frame as shown. 3. Slide pocket underneath base of seat cushion over the front of the seat frame. 3. Repeat steps 1-3 to assemble other side armrest. 4. Hook seat cushion loops onto the pins. Fitting fabric base cover 1. Secure cover to rear of seat frame by wrapping velcro around rear bar as shown. 6 7

5 Fitting fabric base cover (continued) 2. Attach velcro loops on top and bottom of rear fabric around frame as shown. Repeat for loops on other side of rear. Assembling ottoman 1. Place fabric ottoman cover over frame of ottoman. 3. Pass sides of cover behind frame and armrests as shown. 2. Turn ottoman over, and secure velcro loops around bottom of ottoman frame. 4. Attach lowermost velcro loops on cover front around rocking mechanism frame as shown. 5. Attach uppermost velcro loops around sea frame as shown. 3. Place ottoman frame onto ottoman cushion Join the two velcro ends of the fabric cover together. 4. Secure ottoman cushion onto frame using 16mm domed head screws. Tighten using allen key. 8 9

6 Care Instructions Assembling ottoman (continued) 5. Fasten velcro loops on ottoman sides around base of ottoman frame Adjusing backrest Cleaning To ensure the long-lasting use of your rocker chair, wipe down with a damp cloth and use a mild soap solution if necessary. Do not use abrasive cleaners. Always store product in a clean dry place. Maintenance Always check parts regularly for tightness of screws, nuts and other fasteners tighten or replace if required. To maintain the safety of your rocker chair, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by CNP Brands. To adjust backrest, push lever down and slide base of cushion forwards or backwards

7 Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030 Customer Service Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St, Morningside, PO Box , St Lukes, Auckland, New Zealand Customer Service: