Telnet and HyperTerminal Access

Transcription

1 TECHNICAL NOTE 01/2007 Telnet and HyperTerminal Access This document describes how to access certain PowerLogic meter settings with Microsoft Telnet or Windows HyperTerminal applications: If your meter is connected to an Ethernet network, use a telnet application such as Microsoft Telnet. If your meter is connected serially or through a modem to your workstation, use a terminal application such as Windows HyperTerminal. In This Document Using Telnet Meter Logins Telnet Menu Using HyperTerminal Terminal Menu Additional Information Your meter s technical documentation ION Reference Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material Schneider Electric. All rights reserved.

2 Using Telnet Telnet and HyperTerminal Access Using Telnet If your meter is connected to an Ethernet network, use Telnet to perform various functions: access certain Ethernet communications module settings view Ethernet statistics access certain Power Meter module settings access certain Factory module settings clear the front panel event log display (ION8600 meters) configure Factory module setup registers for Current Probe Input applications (ION7550 / ION7650 meters). NOTE Remote access is limited on ION7300 series meters when connected via Ethernet. For full access to commands, connect serially and use HyperTerminal. Connecting to the meter 1. From the Windows Start menu on the lower left side of your computer screen, choose Run... and type the word telnet. Click OK. 2. Type Open and press Return. 3. Type in the meter IP address when prompted and press Enter. NOTE The IP address must match the IP address setup register in the meter Ethernet communications module. Page Schneider Electric. All rights reserved.

3 Telnet and HyperTerminal Access Using Telnet 4. Type your meter s login and press Enter. See below for details. Meter Logins The login is different for each meter. Meter Login ION ION ION ION ION ION ION ION7700 Xpress ION ION ION ION8600* 8600 * Login ID is the same for ION8600A, ION8600B and ION8600C meters. 5. Type the meter password ( 0 by default). Press Enter. NOTE If ten incorrect passwords are entered in succession the Telnet access locks-out for 24 hours or until the security features are disabled with the front panel of the meter. 6. Type? for meter Help screen and press Enter. A list of menu options appears Schneider Electric. All rights reserved. Page 3

4 Telnet Menu Telnet and HyperTerminal Access Telnet Menu The menu options available will vary by meter type. Shown below are the Telnet menu options for two meters, the ION8600 and the ION7300. ION7300 ION8600 This option is available for ION8600 meters only. On ION8600 meters, the available Telnet menu options are: 0) Logout 1) Ethernet Settings 2) Ethernet Stats 3) Meter Clear Functions* 4) Factory Login 9) Switch to Debug Parser (and route msgs to telnet)?) Displays this menu Logout select this option to logout of the meter, and end the Telnet session. Ethernet Settings there are two options in this menu: one for viewing your current communications settings and one for configuring your IP Boot option, IP address, Subnet mask, Gateway address and SMTP address. Ethernet Stats there are three options available in this menu: one for viewing various Ethernet statistics, one for viewing an Ethernet collision histogram, and a third option for resetting these statistics. Meter Clear Functions there are two options available in this menu: one returns you to the Main Menu, and one clears the meter Event Log Display (ION8000 series meters). Page Schneider Electric. All rights reserved.

5 Telnet and HyperTerminal Access Telnet Menu Switch to Debug Parser (and route msgs to telnet) there are eight screens with options available in this menu:? Display Help Screen ALL? COMM? MISC? RESET? SEC? TIME? KAL? LOGIN LOGOUT Display All Commands Display Comm Help Display Miscellaneous Help Display Reset Help Display Security Help Display Time Help Display Calibration Help Factory Login (this menu is reserved for Technical Services use) Logout Accessing menus 1. View the list of menus at any time by typing a question mark (?) and pressing Enter. 2. To access a menu, press the corresponding number on your keyboard, then press Enter Schneider Electric. All rights reserved. Page 5

6 Using HyperTerminal Telnet and HyperTerminal Access Using HyperTerminal If your meter is connected to your workstation via a serial or modem port, use Windows HyperTerminal to access certain meter module settings. NOTE Ensure that the meter COM port you are using has its Protocol register set to Factory. A HyperTerminal session lets you: access certain Factory module settings. access certain Power Meter module settings. clear the front panel event log display (ION8000 series meters). configure Factory module setup registers for Current Probe Input applications (ION7500 / ION7600 meters). Connecting to the meter using Hyperterminal 1. If you have not already done so, set the COM port you are using on the meter to Factory. 2. Launch HyperTerminal from the Start > Programs > Accessories > Communications > HyperTerminal menu. 3. A window requesting a modem install appears. If you wish to install a modem, click Yes and follow the steps. If you do not need to install a modem, click No. The Connection Description window appears. Type in the name for this HyperTerminal session in the Name box. Press Enter. The Connect To window appears. 4. In the Connect Using box, select your PC COM port (e.g. COM1). Press Enter. The COM1 Properties window appears. 5. In the Bits Per Second box, select In the Flow Control box, select None. Page Schneider Electric. All rights reserved.

7 Telnet and HyperTerminal Access Using HyperTerminal 7. For the other settings, use the defaults. The COM Properties window should resemble the window below. 8. Press Enter. A HyperTerminal session window appears. 9. Press Enter. A response indicating an invalid command appears. Below this there is a prompt that indicates the meter type and the PC port where the meter is connected. 10. Type? and press Enter for the Terminal menu Schneider Electric. All rights reserved. Page 7

8 Terminal Menu Telnet and HyperTerminal Access As you toggle between the different Terminal Commands menu options you are required to enter: Login see Meter Logins on page 3. Password type the meter password (default is 0 ). Terminal Menu The Terminal Commands menu options are:? Display Help Screen ALL? COMM? MISC? RESET SEC? TIME? KAL? LOGIN LOGOUT Display All Commands Display Comm Help Screen Display Misc Help Commands Display Reset Help Commands Display Security Help Screen Display Time Help Screen Display Calibration Help Screen Factory login Logout Display Help Screen select this option to display the Factory Terminal menu (menu displayed above). Display All Commands select this option to display every Terminal Command that can be used in HyperTerminal. Page Schneider Electric. All rights reserved.

9 Telnet and HyperTerminal Access Terminal Menu Display Comm Help Screen this option is not used if your meter is connected serially to your workstation. Display Misc Help Screen this option lists commands that allow you to repeat the last command, and display the battery statistics, meter release version, and meter firmware version. Display Reset Help Screen if your security level allows you to perform resets then this screen lists the following options: full or partial factory initialization; restore the factory framework; read power up style; and reset fatal error. Display Security Help Screen select this option to enable/disable password or hardware security, or read the meter lock state. Display Time Help Screen select this option to set or display the meter time, and human meter time: meter time: Unix time (seconds since January 1, 1970) human meter time: day/month/year and hour:minute:second Display Calibration Help Screen select this option to display or configure meter calibration parameters. Factory Login this menu is reserved for Technical Support use. Logout select this option to logout of the meter, and end the HyperTerminal session Schneider Electric. All rights reserved. Page 9