3G Wireless Router CW450 EVDO A, 450MHZ

Transcription

1 3G Wireless Router CW450 EVDO A, 450MHZ Quick Start Guide

2 Thank you for purchasing CW450! This high cost-efficiency router is the best choice for Small office / Home office users, all computers and network devices can share 3G internet via Ethernet or Wi-Fi, and also share a single xdsl / cable modem internet connection at high speed. Easy install procedures allows any computer users to setup a network environment in very short time - within minutes, even inexperienced. Package list Before you starting to use this router, please check if there s anything missing in the package, and contact your dealer of purchase to claim for missing items. Broadband router (main body, 1 pcs) Quick Installation Guide (1 pcs) 9V DC power adapter (1 pcs) Front Panel - 2 -

3 LEDs Status Description Power LAN WAN WiFi 3G On Off On Blink Off On Blink Off On Blink Off On Blink Off The power is ready and it works The power is off. LAN port is successfully connected. Sending / receiving data No Ethernet connection WAN port is successfully connected Sending / receiving data No Modem Connection Radio switch is turned on Sending / receiving data Radio switch is shut off. The 3G service is ready. Trying to link the 3G network. The 3G service is not established. Rear Panel - 3 -

4 Instruction of the ports on the rear panel: Button/port LAN WAN SIM Card Power Reset DC(+9V) Description LAN Port. Connect LAN systems with RJ-45 cable. WAN Port. Connect DSL or Cable modem. SIM card port. Turning on/off the router power. Reset configurations to default. Press the button and hold for 5 seconds. Power jack. Connect with AC power adapter. Installation Before router s set-up, please correctly link according to following steps. In order to achieve product s wireless functions, please put the router in the middle of covered area. Note: The following setup all based on priority setting. You can also connect to the router via wireless using the wireless client software utility

5 Setup using built-in 3 G module 1. Connect the power adapter to the power jack, then plug it into the wall socket. 2. Insert a 3G SIM Card to the SIM card port, and then turn on the router power. 3. Connect your computer to the router s LAN port using an Ethernet cable. 4. Check to make sure the router s LAN LED is lit; to confirm the cable connections are made correctly. Setup using ADSL/Cable Modem 1. Connect the power adapter to the power jack, then plug it into the wall socket. 2. Connect your ADSL/Cable Modem to the router s WAN port using an Ethernet cable

6 3. Connect your computer to the router s LAN port using an Ethernet cable. 4. Check to make sure the router s LAN and WAN LED is lit; to confirm the cable connections are made correctly. Connecting to the Internet To Connect to the Internet via the Web User Interface: 1. Open your IE browser. Type in the address bar and press enter. This opens the login authentication page. 2. Type your Username and Password. Your default Username and Password is admin/admin. -6-

7 3. After your successful login, you enter the CW450 router WEB configuration interface

8 4. Click "Internet Settings" - > "WAN" and enter into the WAN setting page. a) 3G Internet For 3G Internet connection type, you are required to have the following: 1 build-in 3G Module 2 Broadband data SIM card. Select 3G Internet Connection type then set up the rest of the parameters to continue. USB 3G modem:select the type of 3G USB Modem from the - 8 -

9 drop-down list. The default is Auto Detect. Connect Status : The current status of the 3G network connection. Boot-up dial mode:auto & manual. Dial parameter:default & User defined. For 3G Internet Connection select User defined then enter Username, Password, Dial Number, APN and PIN Code provide by your ISP. Click the Apply button to save your setting. b) ADSL/Cable Modem For WAN Internet connection type, you are required to have the following: 1.ADSL/Cable Modem; 2.Active Internet Service Account Select DHCP (Auto Config) for the WAN port. This setting allows the Wireless-N Router to automatically obtain an IP address from a DHCP server normally operated by the Internet Service Provider (ISP)

10 Select STATIC (fixed IP) for the WAN port. Then fill the IP address subnet mask default Gateway primary DNS server and secondary DNS server (you can get parameters from your ISP, and you must enter and fill in at least one parameter) Select PPPoE (ADSL) for the WAN port, you can configure the

11 following parameters to PPPoE dial up through a DSL modem. 5. Chick Wireless Settings --> Basic to the configure page. Check Radio ON to activate your wireless connection and set the SSID for your 3G Wireless-N Router. Click the Apply button to save your setting

12 6. Click "wireless network Settings" - > "Security", going into the Wireless Security/Encryption setup page

13 Select Security Mode to select desired type of encryption for the router Wi-Fi and input encryption key and Click Apply. Click the Apply button to save your setting