BOSSCOM Rotate Slim Bracket with Motor for BeoVision 10 32"and 40".

Transcription

1 BOSSCOM Rotate Slim Bracket with Motor for BeoVision 10 32"and 40". Installation quick guide Important! BOSSCOM DENMARK does not have any responsibility for the way the user mounts the bracket!

2 Introduction. Mount your BeoVision 10 32" or 40" on the new BOSSCOM rotate slim bracket and control it through Beo4, Beo5 or Beo6 remote control like this: Control with Beo4, Beo5 or Beo6. Press on Bang&Olufsen remote control. The menu STAND will be written on the remote s screen. Confirm now the menu point with. Home Left Right *You have the possibility to adjust the Memory option. Swivel the bracket to the desired position (left or right) by using arrow buttons and program the position by pushing and or. **The bracket has Left/Right Wall Limits. Move the bracket to the desire position (leave at least 2-3 cm gap between the wall and TV). Press and or. Even though you keep pressing left or right button it will move till the limit set only. Up Down Setup If you want to reset the Wall Limits you have to push and. Memory 1* Memory 2* Left Limit** Right Limit**

3 List of Contest Introduction.2 Important Safety Instruction 4 Parts and Accessories 5 Required Tools.6 Installation...7

4 Important Safety Instructions. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This bracket shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the bracket. If you install the product by using an improper method, it may cause an injury or product damage. Do not install the product if any parts or components of the bracket are damaged or missing. This product has been designed for use on a vertical wall. For safe installation, the wall must maintain four times of the total load (including the wall mount and TV itself). Remove unnecessary attachments on the wall where you will install the wall mount. Do not use this bracket near water. Clean only with dry cloth. Do not install near any heat sources, heat registers, stoves, or other devices that produce heat. Only use accessories specified by the manufacturer. Unplug this device during lightning storms or when unused for long periods of time. Before mounting adapters and TV to the bracket secure that ALL screws are mounted safely and correct.

5 Parts and Accessories. The set includes: motorized wall bracket, adaptor plate for motorized bracket, TV adaptor for BeoVision 10 32"/ BeoVision 10 40", power supply, IR box and different screws. TV Adaptor for BeoVision 10 32"/ BeoVision 10 40" (Part1*) Adaptor Plate for Motorized Bracket (Part2**) Motorized Wall Bracket (Part 3***)

6 IR Box Power Supply Screws 1. To fix Part 1 to TV. 2. To fix Part 1 and Part 2 together. 3. To hang Part 2 on the Part3 Required Tools

7 Installation. Part 1* Part 2** Part 3*** 1. Drill the motorized wall bracket (Part 3***) to the wall. 2. To fabricate the TV on the motorized bracket that is fastened on the wall, you should pull horizontally, turn it over 90 degrees and fix the adaptor plates. 3. Fix the TV adaptor (Part 1*) and adaptor plate for motorized bracket (Part 2**) together. 4. Adjust the screws to the adaptor plate for motorized bracket (Part 2**) so the TV could be mounted on the motorized wall bracket (Part 3***). 5. Tighten the TV adaptor (Part 1*) (together with adaptor plate for motorized bracket) to the TV (notice that BeoVision 10 32" and BeoVision 10 40" have different hole positions on the adaptor). 6. Mount the TV with adapters on the motorized bracket (Part 3***). 7. Connect power supply and IR box to the terminal as shown in the picture below:

8 8. Place the IR Box on the back of TV. Please make sure that IR box is in the middle and straight with the bottom of the TV as shown in the picture below. BeoVision 10 trademark belonging to Bang&Olufsen A/S. BOSSCOM has no connection to Bang&Olufsen A/S and BOSSCOM recognizes Bang&Olufsen A/S trademark rights.