CommScope Packaging and Shipping Requirements

Transcription

1 Packaging Specification Jan13 Rev L CommScope Packaging and Shipping Requirements 1. SCOPE 1.1. Content This specification describes the packaging and shipping requirements for CommScope Quick Connectors (LC, SC, ST) non secured products as shown in Figure 2 and the CommScope Keyed Connectors and Adapters (LC) secured products. Figure 1 shows the TE Connectivity Specification Number to be used, Paragraph Number and CommScope Product Description. TE Specification Number Paragraph Number CommScope Product Description , 4.2., 4.3., 4.4. Quick Connectors , 5.2. Individually Packaged Adapters , 5.4. Bulk Packaged Adapters , 5.6. Individually Packaged LC Keyed Connectors , 5.8. Bulk Packaged LC Keyed Connectors Figure 1 NOTE All documentation including Straight Bill of Lading, all Shipping Labels, Packing List, Carrier Bill of Ladings example: DHL, FedEx, UPS or any other type of carrier, see Figures 14, 15 and 16 for examples. Cannot have any reference to TE Connectivity or any Trademark Logo s on any or all paperwork for Drop Shipments to CommScope customers Application A. Paragraph 4 defines the CommScope non SECURE packaging requirements. B. Paragraph 5 defines the CommScope SECURE packaging requirements. C. Paragraph 6 defines the CommScope shipping requirements. 2. DEFINITIONS A. Non secured product: 900 um (unit micron) connectors packaged in blister pack (LightCrimp Plus LC, SC, ST, SM and MM) B. Secured product: Keyed (LC SECURE) multimode (MM) and single mode (SM) connectors (BTW 900 um (behind the wall), Simplex ( mm jacket) or Duplex Kits ( mm jacket) and adapters (Standard and Hybrid) 3. APPLICABLE DOCUMENT The following document constitutes a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies Specification : Standard Packaging, Packing, Marking and Palletizing Methods 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company All Rights Reserved Indicates Change This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at PRODUCT INFORMATION *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners. 1 of 19

2 Material ID (MID) TE Part Number NON SECURED DOCUMENT Product Code Product Description QK-LC-BTW-SM-25PK QK-LC, BTW, SM Installer PK (25) QK-LC-BTW-LS-25PK QK-LC, BTW, LS 50/125, Installer PK (25) QK-LC-BTW-MM-25PK QK-LC, BTW, MM 62.5/125, Installer PK (25) QK-SC-BTW-SM-25PK QK-SC, BTW, SM Installer PK (25) QK-SC-BTW-LS-25PK QK-SC, BTW, LS 50/125, Installer PK (25) QK-SC-BTW-MM-25PK QK-SC, BTW, MM 62.5/125, Installer PK (25) QK-ST-BTW-LS-25PK QK-ST, BTW, MM 50/125, Installer PK (25) QK-ST-BTW-MM-25PK QK-ST, BTW, MM 62.5/125, Installer PK (25) Material ID (MID) TE Part Number NON SECURED PRODUCT Product Code Product Description / SFC-LCQ-09-8X-25-PK QK-LC, BTW, SM Installer PK (25) / MFC-LCQ-09-5X-25-PK QK-LC, BTW, LS 50/125, Installer PK (25) / MFC-LCQ-09-6X-25-PK QK-LC, BTW, MM 62.5/125, Installer PK (25) / SFC-SCQ-09-8X-25-PK QK-SC, BTW, SM Installer PK (25) / MFC-SCQ-09-5X-25-PK QK-SC, BTW, LS 50/125, Installer PK (25) / MFC-SCQ-09-6X-25-PK QK-SC, BTW, MM 62.5/125, Installer PK (25) / MFC-STQ-09-5X-25-PK QK-ST, BTW, MM 50/125, Installer PK (25) / MFC-STQ-09-6X-25-PK QK-ST, BTW, MM 62.5/125, Installer PK (25) Figure 2 Non Secured Product 4. PACKAGING PROCEDURE (NON-SECURE PRODUCT) , Pre-Pack for QK_LC BTW Connector Kit (25 Pack), (SM), (LS), (MM), /00 (SM), /00 (LS) and /00 (MM) A. Place the number of each part as specified in the Manufacturing Pro (MFG PRO) or Packaging and Labeling Inquiry System (PALI) in accordance with the following: 1. Open blister pack PN so that the hinge is to the left, place on work surface. 2. With the blister pack open and hinged to the left, place 25 LC BTW connectors in upper right compartment (connectors are to have a protective cover and protective cap installed). 3. With the blister pack open and hinged to the left, place 25 connector boots in lower right compartment. 4. Place 25 hytrel tubes in a 2 inch x 2 inch resealable plastic bag PN With the blister pack open and hinged to the left, place bagged tubes in upper left compartment. 5. Fold instructions (2 folds on an 8.5 x 11 double sided print bond paper) and add to blister pack along with insert card PN Close blister pack, apply product label to upper left of pack. Rev L 2 of 19

3 B. Product label on blister pack should be similar to Figure 3A. Figure 3A C. Shipping box label should be similar to Figure 3B. Figure , Pre-Pack for QK_SC BTW Connector Kit (25 Pack), (SM), (LS), (MM), /00 (SM), /00 (LS) and /00 (MM) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Open blister pack PN so that the hinge is to the left, place on work surface. 2. With the blister pack open and hinged to the left, place 25 SC BTW connectors in upper right compartment (connectors are to have a protective cover and protective cap installed). 3. With the blister pack open and hinged to the left, place 25 connector boots in lower right compartment. 4. Place 25 hytrel tubes in a 2 inch x 2 inch resealable plastic bag PN With the blister pack open and hinged to the left, place bagged tubes in upper left compartment. Rev L 3 of 19

4 5. With blister pack open and hinged to the left, place 25 SC connector housings in lower left compartment. 6. Fold instructions (2 folds on an 8.5 x 11 double sided print bond paper) and add to blister pack along with insert card PN Close blister pack, apply product label to upper left of pack. B. Product label on blister pack should be similar to Figure 4A. Figure 4A C. Shipping box label should be similar to Figure 4B. Figure 5 Rev L 4 of 19

5 , Pre-Pack for QK_ST BTW Connector Kit (25 Pack), (MM), (MM), /00 (MM) and /00 (MM) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Open blister pack PN so that the hinge is to the left, place on work surface. 2. With the blister pack open and hinged to the left, place 25 ST BTW connector assemblies in upper right compartment (connectors are to have a protective cover and protective cap installed). 3. With the blister pack open and hinged to the left, place 25 connector bare buffer boots in lower right compartment. 4. pack open and hinged to the left, place bagged tubes in upper left compartment. 5. Fold instructions (2 folds on an 8.5 x 11 double sided print bond paper) and add to blister pack along with insert card PN Close blister pack, apply product label to upper left of pack. B. Product label on blister pack should be similar to Figure 5A. Figure 5A C. Shipping box label should be similar to Figure 5B. Figure 5B Rev L 5 of 19

6 4.4. Final Pack (All Connector Kits) A. Form one box PN and seal bottom flaps with a 2 inch wide strip of tape PN (or equivalent). B. Place a minimum of 2, up to a maximum of 10 blister pack kits (from pre-pack) into box. (Alternate packing, use an appropriately sized blank carton for a quantity of one blister pack kit). C. Fill void with stuffer paper. D. Close flaps and seal with tape, same as bottom flaps. E. Label one end of box with a product package or 3S label. Reference MFG PRO/PALI for label requirements. Palletize in accordance with Packaging Specification , paragraph on General Palletization Parameters. F. Whenever an overpack carton is used, CARTON MUST BE BLANK, NO LOGOS ALLOWED. G. Stretchwrap and/or band pallet load. H. Apply Carrier ship to label and packing list. See Figure 14 and 15 for packing list and Carrier ship to requirements. TE Connectivity logo should not be printed on labels or packing list. 5. PACKAGING PROCEDURE (SECURE PRODUCTS) , Pre-Pack (all LC SECURE individual adapters) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Place adapter into (5x4) poly bag or (5x4) poly bag and seal. 2. Apply label (2 x 4) similar to Figure 6A to poly bag. 3. Place 100 of the individual bagged adapters into re-sealable bag, close bag. 4. Apply label (2 x 4) similar to Figure 6B to poly bag. B. Product unit label on or should be similar to Figure 6A Bag Label Figure 6A Paper Label Rev L 6 of 19

7 C. Product intermediate label on should be similar to Figure 6B. Figure 6B , Final Pack (all LC SECURE individual adapters) A. Form one box PN (no graphics allowed) and seal bottom flaps with a 2 inch wide strip of tape PN (or equivalent). B. Place 1 ziplock bag PN into a box. C. Fill void with stuffer paper. D. Close flaps and seal with tape. E. Apply shipping label (4 x 4) similar to Figure 7. Reference MFG PRO/PALI for label requirements. Palletize in accordance with Packaging Specification , paragraph on General Palletization Parameters. F. Juarez and Delicias manufacturing - apply License Tag (1x3) to box, see Figure 7 for placement. G. Delicias Manufacturing Only Shipments from Delicias to 8420 Triad, Greensboro, N.C. Commscope boxes to be placed in overpack shipping box. H. Whenever an overpack carton is used for shipment to the customer, CARTON MUST BE BLANK, NO LOGOS ALLOWED. I. Stretchwrap and/or band pallet load. J. Apply Carrier ship to label and packing list. See Figure 14 and 15 for packing list and Carrier ship to requirements. TE Connectivity logo should not be printed on labels or packing list. Rev L 7 of 19

8 Figure 7 (continued) Figure 7 (end) , Pre-Pack (all LC SECURE bulk adapters) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Place 25 loose adapters into re-sealable bag, close bag. NOTE Unit of measure is packs. 1 pack = 25 pieces Rev L 8 of 19

9 2. Apply label (2 x 4) similar to Figure 8 to poly bag. Figure , Final Pack (all LC SECURE bulk adapters) A. Form one box PN (no graphics allowed) and seal bottom flaps with a 2 inch wide strip of tape PN (or equivalent). B. Place 4 ziplock bags PN into a box. C. Fill void with stuffer paper. D. Close flaps and seal with tape. E. Apply shipping label (4 x 4) similar to Figure 9. Reference MFG PRO/PALI for label requirements. Palletize in accordance with Packaging Specification , paragraph on General Palletization Parameters. F. Juarez and Delicias Manufacturing - apply License (1 x 3) Tag to carton, see Figure 9 for placement. G. Delicias Manufacturing Only Shipments from Delicias to 8420 Triad, Greensboro, N.C. Commscope boxes to be placed in overpack shipping box. H. Whenever an overpack carton is used, CARTON MUST BE BLANK, NO LOGOS ALLOWED. I. Stretchwrap and/or band pallet load. J. Apply Carrier ship to label and packing list. See Figure 14 and 15 for packing list and Carrier ship to requirements. TE Connectivity logo should not be printed on labels or packing list. Rev L 9 of 19

10 Figure 9 (continued) Figure 9 (end) , Pre-Pack (all LC SECURE individual connectors) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Place all components into (5x4) poly bag or (5x4) poly bag and seal. 2. Apply label (2 x 4) similar to Figure 10A to poly bag. 3. Place 100 of the individual bagged connector kits into re-sealable bag, close bag. 4. Apply label (2 x 4) similar to Figure 10B to poly bag. B. Product unit label on or should be similar to Figure 10A. Rev L 10 of 19

11 Bag Label Paper Label Figure 10A C. Product label on should be similar to Figure 10B. Rev L 11 of 19

12 Figure 10B , Final Pack (all LC SECURE individual connectors) A. Form one box PN (no graphics allowed) and seal bottom flaps with a 2 inch wide strip of tape PN (or equivalent). B. Place maximum of 1 bag into a box. C. Fill void with stuffer paper. D. Close flaps and seal with tape. E. Apply shipping label (4 x 4) similar to Figure 11 to middle of box, see Figure 11. Reference MFG PRO/PALI for label requirements. Palletize in accordance with Packaging Specification , paragraph on General Palletization Parameters. F. Juarez and Delicias Manufacturing - apply License (1 x 3) Tag below CommScope label, see Figure 11. G. Delicias Manufacturing Only Shipments from Delicias to 8420 Triad, Greensboro, N.C. Commscope boxes to be placed in overpack shipping box. H. Whenever an overpack carton is used, CARTON MUST BE BLANK, NO LOGOS ALLOWED. I. Stretchwrap and/or band pallet load. J. Apply Carrier ship to label and packing list. See Figure 14 and 15 for packing list and Carrier ship to requirements. TE Connectivity logo should not be printed on labels or packing list. Rev L 12 of 19

13 Figure 11(continued) Figure 11 (end) , Pre-Pack (all LC SECURE bulk connectors) A. Place the number of each part as specified in MFG PRO/PALI in accordance with the following: 1. Component package each part in a bag. See print for required part number and quantity. No printing on bag. 2. Place all components into re-sealable bag, close bag. 3. Apply label (2 x 4) similar to Figure 12 to poly bag. Rev L 13 of 19

14 B. Product label on should be similar to Figure 12. Figure , Final Pack (all LC SECURE bulk connectors) NOTE Unit of measure in packs. 1 pack = 100 pieces A. Form one box PN (no graphics allowed) and seal bottom flaps with a 2 inch wide strip of tape PN (or equivalent). B. Place one ziplock bag into a box. C. Fill void with stuffer paper. D. Close flaps and seal with tape. E. Apply shipping label (4 x 4) similar to Figure 13. Reference MFG PRO/PALI for label requirements. Palletize in accordance with Packaging Specification , paragraph on General Palletization Parameters. F. Juarez and Delicias Manufacturing - apply License (1 x 3) Tag , see Figure 13, to carton. See Figure 7 for placement on carton. G. Delicias Manufacturing Only Shipments from Delicias to 8420 Triad, Greensboro, N.C. Commscope boxes to be placed in overpack shipping box. H. Whenever an overpack carton is used, CARTON MUST BE BLANK, NO LOGOS ALLOWED. I. Stretchwrap and/or band pallet load. J. Apply Carrier ship to label and packing list. See Figure 14 and 15 for packing list and Carrier ship to requirements. TE Connectivity logo should not be printed on labels or packing list. Rev L 14 of 19

15 Figure 13 (continued) Figure 13 (end) Rev L 15 of 19

16 6. SHIPPING REQUIREMENTS 6.1. See Figure 14 for packing list requirements and format See Figure 15 for examples of the Carrier ship to shipping label requirements See Figure 16 for example of Bill of Lading requirements. Figure 14 (continued) Page 1 of Packing List Figure 14 (end) Page 2 of Packing List Rev L 16 of 19

17 Figure 15 (continued) Rev L 17 of 19

18 Figure 15 (end) Rev L 18 of 19

19 Figure 16 Rev L 19 of 19