Metrologic MS1633 FocusBT Cordless 2D Scanner Installation Guide

Transcription

1 Metrologic MS1633 FocusBT Cordless 2D Scanner Installation Guide Revision 1.0

2 Revision History /03/2007 Initial Release The latest version of this document can be found in the following places: Internally for Cerner associates in the Cerner Knowledge Repository (KR) using the search function with the keywords: Metrologic or MS1633 Internally for Cerner associates on My Cerner using the search function with the keywords: Metrologic or MS1633 Externally for clients and Cerner associates on under the Support tab, Millennium Infrastructure Documentation, Peripherals, Bar-Code Scanners, Metrologic. 2 MS1633 Focus BT Scanner Installation Guide

3 Table of Contents Revision History... 2 Table of Contents... 3 Overview... 4 LED and Beep Meanings...5 Metrologic MS1633 Scanner Setup (USB CodeXML Modem)... 6 Cerner Millennium Configuration...6 Cerner Classic Configuration...8 Metrologic MS1633 Scanner Setup (USB Bluetooth Adapter) MetroBT Driver Installation...10 MetroBT Utility Installation...15 SoftWedge Installation...17 MS1633 FocusBT Connection Setup...21 Testing MS1633 FocusBT Scanner Connection...26 Setting up the Scanner for Cerner Millennium Applications...26 Setting up the Scanner for Cerner Classic Applications...26 Metrologic MS1633 Scanner Setup (Keyport for Bluetooth) Installing Keyport Bluetooth...27 MS1633 FocusBT Connection Setup...31 Testing MS1633 FocusBT Scanner Connection...33 Setting up the Scanner for Cerner Millennium Applications...34 Setting up the Scanner for Cerner Classic Applications...34 Symbology Selection Miscellaneous Optional Setup Procedures Hands Free (Presentation) Mode...37 Setting Beep Tone...38 Reset Scanner to Factory Defaults...38 Show Firmware Revision...39 Sample Bar Codes Linear Sample Bar codes D Sample Bar codes...41 MS1633 Focus BT Scanner Installation Guide 3

4 Metrologic FocusBT Cordless 2D Scanner Installation Guide Overview This guide provides a Cerner-specific installation methodology for the following Metrologic scanner model. Model Kit Part Number Description MS MK B40 MS1633 FocusBT Cordless 2D Scanner with USB CodeXML Bluetooth Modem MS MK B05 MS1633 FocusBT Cordless 2D Scanner with Class2 USB Bluetooth Adapter Verify the scanners model number by comparing the Model and the type located on the bottom of the scanner to the ones listed above. You also can compare the number on the box the scanner came in with the kit part number above. If the numbers do not match then this document should not be used to set up the scanner. To determine your scanners model number see the above two circles. In this example the model number is: MS This documentation should be used in place of the manufacturers documentation. The manufacturer s documentation is provided with the scanner in the event that it might be needed at a later date. It is assumed that the reader understands how to attach peripheral devices and load software on Windows based PCs. If you need additional assistance, contact your institution s help desk, your Cerner account team or Cerner s Client Care Team in Kansas City Missouri call or toll free at (866) for assistance. 4 MS1633 Focus BT Scanner Installation Guide

5 LED and Beep Meanings The MS1633 has three LED indicators (yellow, white and blue) located on the top of the scanner. When the scanner is on, the flashing or stationary activity of the LED s indicates the status of the current scan and the scanner. The Beep also indicates the status of the scans. Normal Operation Feedback LED Beep Meaning None None Scanner not powered on or no barcode being scanned. Steady Yellow None Scanner is in the presentation stand. Steady Blue None The blue LED is illuminated when the scanner is active and linear illumination is on or when the scanner is attempting to decode a barcode. Steady Blue & 1 Beep When the scanner successfully reads a bar code it will beep once and Single White Flash the White LED will turn on indicating data is being transmitted. Steady White 1 Beep When the scanner successfully reads a bar code it will beep once and the White LED will turn on indicating data is being transmitted. If the host is not ready to accept the information, the scanner s white LED Alternating Flashing Blue and White None will remain on until the data can be transmitted. This indicates the scanner is in configuration mode. A short razzberry tone indicates that an invalid bar code has been scanned while in this mode. Flashing Blue None The blue LED will flash if the trigger is pressed while the scanner is in the in-stand presentation mode. The blue LED will stop flashing after a brief period of time. White LED Flash Flashing Blue Long Razzberry Tone During Power Up Short Razzberry Tone Durring Scanning 3 Beep after power up 3 Beeps in Configuration Mode 3 beeps Med / High / Low 3 Beeps in Normal Mode 2 beeps Low / High 2 beeps High / Low Double Razz Tone Failed to initialize or configure the scanner. If the scanner does not respond after reprogramming, return the scanner for repair. An Invalid bar code has been scanned when in configuration mode or the trigger has been pulled too fast. Scanner ready for use. Scanner has entered configuration mode. When using single code configuring this 3 beeps indicate that the barcode successfully configured the scanner. Communication Error Bluetooth connection has been made Bluetooth connection has been disconnected When the Bluetooth communication link is not active, the scanner will emit a double razz tone and the Blue LED will start to flash. This can occur when the scanner is out of Bluetooth communication range from the host system and the RangeGate feature is disabled. MS1633 Focus BT Scanner Installation Guide 5

6 Metrologic MS1633 Scanner Setup (USB CodeXML Modem) Cerner Millennium Configuration If you are installing your MS1633 scanner using the USB CodeXML Modem on your PC running in a Cerner Millennium environment please perform the following steps. If you are installing your MS1633 scanner using the Metrologic USB Bluetooth adapter please move to that section of this document as the instructions in this section are not designed for your scanner. 1. Connect the USB interface cable to the CodeXML Modem and to an unused USB port on the PC or thin client. 2. Make sure your scanner is fully charged and powered on. 3. Scan the following barcode in the order they appear. Factory Defaults ³ Enter/Exit Config Mode ³ MS1633 Focus BT Scanner Installation Guide

7 Cerner Millennium Configuration (Continued) Disable CR Suffix ³ Disable LF Suffix ³ Enable CodeXML Protocol ³ Next scan the Bluetooth Address Code Barcode on the top of the CodeXML Modem. Enter/Exit Config Mode ³ Note: Please wait for a Low / High beep before proceeding. (About 10 seconds) At this point the scanner is configured for the Cerner Millennium environment using a Horizontal TAB suffix. Please proceed to the section titled Symbology Selection MS1633 Focus BT Scanner Installation Guide 7

8 Metrologic MS1633 Scanner Setup (USB CodeXML Modem) Cerner Classic Configuration If you are installing your MS1633 scanner using the USB CodeXML Modem on your PC running in a Cerner Classic environment please perform the following steps. If you are installing your MS1633 scanner using the Metrologic USB Bluetooth adapter please move to that section of this document as the instructions in this section are not designed for your scanner. 1) Connect the USB interface cable to the CodeXML Modem and to an unused USB port on the PC or thin client. 2) Make sure your scanner is fully charged and powered on. 3) Scan the following barcode in the order they appear. Factory Defaults ³ Enter/Exit Config Mode ³ MS1633 Focus BT Scanner Installation Guide

9 Cerner Classic Configuration (Continued) Disable CR Suffix ³ Disable LF Suffix ³ Enable CodeXML Protocol ³ ) Next scan the Bluetooth Address Code Barcode on the top of the CodeXML Modem. Enter/Exit Config Mode ³ Note: Please wait for a Low / High beep before proceeding. (About 10 seconds) At this point the scanner is configured for the Cerner HNA Classic environment using a Carriage Return suffix. Please proceed to the section titled Symbology Selection MS1633 Focus BT Scanner Installation Guide 9

10 Metrologic MS1633 Scanner Setup (USB Bluetooth Adapter) If you are installing your MS1633 scanner using the Metrologic USB Bluetooth Adapter on your PC please perform the following steps. If you are installing your MS1633 scanner using the USB CodeXML Modem please move to that section of this document as the instructions in this section are not designed for your scanner. To install the Metrologic MS1633 FocusBT scanner with a Bluetooth adapter you will need to load 3 software applications on your PC. These applications are on the CD that came with your scanner. MetroBT Driver, MetroBT Utility, SoftWedge Note: This installation document is used as a guide, the information should be the same but the screens may very. MetroBT Driver Installation 1) Load the included FocusBT CD into the CD-ROM drive on the host / computer. 2) If the CD-ROM does not automatically open, click on the window s Start button, choose Run, then click Browse to locate and open the CD-ROM drive. Double-Click on the Metrologic.exe file then click OK. 3) Click on the MetroBT Driver button to begin the installation. 10 MS1633 Focus BT Scanner Installation Guide

11 MetroBT Driver Installation (Continued) 4) Choose a Setup Language the click OK. 5) At the welcome screen select Next. MS1633 Focus BT Scanner Installation Guide 11

12 MetroBT Driver Installation (Continued) 6) After reviewing the end user license agreement, select the I accept the terms of the license agreement option, then click Next to continue. 7) Choose Install from the Ready to Install the Program screen. 12 MS1633 Focus BT Scanner Installation Guide

13 MetroBT Driver Installation (Continued) 8) To continue the installation procedure without showing warnings for unauthorized drivers, select I accept and click OK. 9) Plug the Bluetooth USB Adapter into the host device USB port then click OK to indicate MS1633 Focus BT Scanner Installation Guide 13

14 MetroBT Driver Installation (Continued) 10) When the installation is complete the InstallShield Wizard Complete window will appear. Click Finish to continue. 11) After the installation completes click on Yes to restart the host device / computer. The host / computer must be rebooted at this time in order for the driver to function properly. 14 MS1633 Focus BT Scanner Installation Guide

15 MetroBT Utility Installation 12) After the computer reboots eject and reload the included FocusBT CD into the CD-ROM drive on the host / computer if it s not already loaded. 13) If the CD-ROM does not automatically open, click on the window s Start button, choose Run, then click Browse to locate and open the CD-ROM drive. Double-Click on the Metrologic.exe file then click OK. 14) Click on the MetroBT Utility button to begin the installation. 15) Click OK to continue. 16) Locate the COMReconnect icon on the Windows desktop and double click to open the program. MS1633 Focus BT Scanner Installation Guide 15

16 MetroBT Utility Installation (Continued) 17) In the Auto Reconnect Utility click the box in the left lower corner Place icon in the taskbar to keep the utility active when the window is closed. Click the Close button to close this window. 16 MS1633 Focus BT Scanner Installation Guide

17 SoftWedge Installation 18) Click on the SoftWedge button to begin the installation. 19) At the welcome screen select Next. MS1633 Focus BT Scanner Installation Guide 17

18 SoftWedge Installation (Continued) 20) At the Destination Folder select Next. 21) Choose Install from the Ready to Install the Program screen. 18 MS1633 Focus BT Scanner Installation Guide

19 SoftWedge Installation (Continued) 22) When the installation is complete the InstallShield Wizard Completed window will appear. Click Finish to continue. This will launch the Metrologic SoftWedge Utility. 23) When the Metrologic SoftWedge Utility window appears click OK to close window. MS1633 Focus BT Scanner Installation Guide 19

20 SoftWedge Installation (Continued) 24) Select Exit to exit the installation. Note: All the software required to connect and use the MS1633 Bluetooth scanner is now installed. Next we need to configure the software and establish a Bluetooth connection with the scanner. 20 MS1633 Focus BT Scanner Installation Guide

21 MS1633 FocusBT Connection Setup 25) Double-Click on the Bluetooth icon on the Windows Start bar in the bottom right corner of the screen. 26) The new connection wizard will automatically start. Power up the FocusBT scanner and allow it to boot completely. Three beeps will indicate the scanner is completely booted. Select Express Mode the click Next. MS1633 Focus BT Scanner Installation Guide 21

22 MS1633 FocusBT Connection Setup (Continued) 27) A search for the Bluetooth devices should find the Focus BT scanner. The number(s) next to FocusBT indicate the serial number of the unit(s) found. Select the proper device and click Next to continue. 28) The final screen of the New Connection Wizard should indicate the virtual Bluetooth Com port that was setup. This will usually be a high number, as seen in the screen below. Remember this COM number. Click Next to continue. 22 MS1633 Focus BT Scanner Installation Guide

23 MS1633 FocusBT Connection Setup (Continued) 29) If your scanner has not already connected right click on the icon and select Connect in order to establish a Bluetooth link between the FocusBT scanner and your computer. Note: The FocusBT scanner should emit a connection tone and the blue light on the top of the unit should stop blinking indicating a connection has been established. 30) Click the Red X in the top right corner of the window to close. MS1633 Focus BT Scanner Installation Guide 23

24 MS1633 FocusBT Connection Setup (Continued) 31) Locate the COMReconnect icon on the Windows desktop and double click to open the program. 32) Click the Refresh button in the lower right hand corner of the window to Display the FocusBT scanner to be managed. Click the Box (if not already selected) to the left of the PortName to select the scanner. Click Close to close the window. 33) Bring up the Metrologic SoftWedge Utility by clicking the SoftWedge Icon in the Task Tray in the lower right hand side of the Desktop. This will bring up the SoftWedge Utility window. 24 MS1633 Focus BT Scanner Installation Guide

25 MS1633 FocusBT Connection Setup (Continued) 34) In the Metrologic SoftWedge Utility window under Comm Port select the COMM port your scanner is connected to. This port was established at the end of the Add a New Connection Wizard in the beginning of the FocusBT Connection Setup section. 35) Next to Port Selected Click the Box. At this point you will notice that the red Not Connected will be replaced by a green Connected Click OK to close the window. MS1633 Focus BT Scanner Installation Guide 25

26 Testing MS1633 FocusBT Scanner Connection To test your MS1633 FocusBT scanners Bluetooth connection open up Microsoft Notepad or Microsoft Word and scan the following barcode. If the barcode scans into the application then your scanners Bluetooth connection has been established. Code Setting up the Scanner for Cerner Millennium Applications Note: If you are not running Cerner Millennium applications skip this section. Scan the following barcodes to sets up the scanners suffix to a Horizontal TAB for most Cerner Millennium applications. If this does not work for your application try scanning the configuration barcodes for Cerner Classic. Disable CR Suffix ³ Enable TAB Suffix ³ Setting up the Scanner for Cerner Classic Applications Note: If you are not running Cerner Classic applications skip this section. Scan the following barcodes to set up the scanners suffix to a Carriage Return for Cerner Classic applications. Disable TAB Suffix ³ Enable CR Suffix ³ Please proceed to the section titled Symbology Selection 26 MS1633 Focus BT Scanner Installation Guide

27 Metrologic MS1633 Scanner Setup (Keyport for Bluetooth) Installing Keyport Bluetooth 1) Insert Keyport Bluetooth CD-ROM in your CD or DVD Drive. 2) Go to My Computer and double click on your CD or DVD Drive that corresponds to the Keyport Bluetooth CD-ROM. 3) This will open a window showing the contents of the Keyport Bluetooth CD-ROM. 4) Double click on the Keyport Bluetooth.msi program. 5) The welcome screen will be displayed, Click the button to continue. MS1633 Focus BT Scanner Installation Guide 27

28 Installing Keyport Bluetooth (Continued) 6) The Select Installation Folder screen will appear. In the lower left hand corner of the screen under Install Keyport for yourself or for everyone who uses this computer Select Everyone Then click the button to continue. 7) The Confirm Installation Screen will appear. Click the button to continue. 28 MS1633 Focus BT Scanner Installation Guide

29 Installing Keyport Bluetooth (Continued) 8) At this point Keyport Bluetooth will be loaded on your computer. You will see the Installing Keyport Bluetooth screen and a progress bar. 9) When the installation is complete the Installation Complete screen will appear. Click the button to exit the installer. MS1633 Focus BT Scanner Installation Guide 29

30 Registering Keyport Bluetooth 10) From the menu select: All Programs Keyport Bluetooth Keyport Bluetooth.exe 11) This will bring up the Keyport for Bluetooth Application. Select the Registration tab at the top right of the window. 12) Fill out the registration information as requested on the screen. The serial number can be found on the Installation CD-ROM. 30 MS1633 Focus BT Scanner Installation Guide

31 MS1633 FocusBT Connection Setup 13) Power up the FocusBT scanner and allow it to boot completely. Three beeps will indicate the scanner is completely booted. 14) To establish a connection with the MS1633 FocusBT scanner click the Connections tab and then click the Discover Button. 15) Select the FocusBT scanner from the list and click the Connect Button. MS1633 Focus BT Scanner Installation Guide 31

32 MS1633 FocusBT Connection Setup (Continued) Note: The FocusBT scanner should emit a connection tone and the blue light on the top of the unit should stop blinking indicating a connection has been established. Click the OK button to close the window. 32 MS1633 Focus BT Scanner Installation Guide

33 Testing MS1633 FocusBT Scanner Connection 16) To test your MS1633 FocusBT scanners Bluetooth connection, make sure the keyport for Bluetooth application is selected and scan the following barcode: Code You should see the Keyport for Bluetooth automatically switch to the Trace window and the scanned information should be displayed. MS1633 Focus BT Scanner Installation Guide 33

34 Setting up the Scanner for Cerner Millennium Applications Note: If you are not running Cerner Millennium applications skip this section. Scan the following barcodes to sets up the scanners suffix to a Horizontal TAB for most Cerner Millennium applications. If this does not work for your application try scanning the configuration barcodes for Cerner Classic. Disable CR Suffix ³ Enable TAB Suffix ³ Setting up the Scanner for Cerner Classic Applications Note: If you are not running Cerner Classic applications skip this section. Scan the following barcodes to set up the scanners suffix to a Carriage Return for Cerner Classic applications. Disable TAB Suffix ³ Enable CR Suffix ³ Please proceed to the section titled Symbology Selection 34 MS1633 Focus BT Scanner Installation Guide

35 Symbology Selection Scan the following bar codes in the order in which they appear. Enter/Exit Config Mode ³ Enable RSS 14 ³ No RSS 14 App ID ³ No RSS 14 Sym ID ³ Enable RSS Limited ³ No RSS Limited App ID ³ No RSS Limited Sym ID ³ Enable Code 39 (Full) ³ Enable Standard 2 of 5 ³ MS1633 Focus BT Scanner Installation Guide 35

36 Symbology Selection (Continued) Enable ISBT 128 ³ Enable Aztec ³ Enable Data Matrix ³ Enter/Exit Config Mode ³ MS1633 Focus BT Scanner Installation Guide

37 Miscellaneous Optional Setup Procedures Hands Free (Presentation) Mode To use the MS1633 scanner in presentation mode place the scanner in the presentation stand. Placing the scanner in the stand automatically configures the scanner into presentation mode. Once the scanner is in the stand and the IR sensor detects an object in the IR activation range the scanner s light automatically starts to flash as it attempts to scan the bar code. The scanner continuously attempts to scan the bar code until either it succeeds or the bar code is removed from the scanner s field of view. When scanner successfully reads the bar code it will beep once, the white LED will flash and the decoded data will be transmitted to the host. MS1633 Focus BT Scanner Installation Guide 37

38 Setting Beep Tone To adjust the beepers frequency and volume scan the appropriate bar code(s). Normal ³ Low Fequency ³ Med Fequency ³ High Fequency ³ Reset Scanner to Factory Defaults Scan the following barcode to reset the scanner back to factory defaults. Factory Defaults ³ MS1633 Focus BT Scanner Installation Guide

39 Show Firmware Revision Follow this procedure to display the firmware revision of your scanner. 1. Bring up Microsoft Word, WordPad or Notepad and make sure your curser is in the editors window. 2. Scan the following barcode. Scan Count Mode On ³ Note: be careful not to open or click any other windows after you enter scan count mode. You should now be seeing something that looks like this: Note: The last block of numbers is the firmware revision level. In this case it would be: Scan the following barcode to turn off Scan Count. Scan Count Mode Off ³ MS1633 Focus BT Scanner Installation Guide 39

40 Sample Bar Codes Use these bar codes to test your imager using Microsoft Word or WordPad. Linear Sample Bar codes Codabar Code 128 A B Code 39 (Normal) RSS-14 A B C Code 39 (Full ASCII) UPC-A A B C & Interleaved 2 of 5 Standard 2 of RSS Limited MS1633 Focus BT Scanner Installation Guide

41 2D Sample Bar codes PDF417 This is a sample of the PDF417 symbology. This symbology can store a lot of information in a small space. Aztec Code This is a sample of the 2D "Aztec Code" symbology. This symbology can store a lot of information in a small space. Data Matrix This is a sample of the 2D "Data Matrix" symbology. This symbology can store a lot of information in a small space. Metrologic MS1690 2D Scanner Installation Guide 41