SMC Wireless Barricade Routers

Transcription

1 SMC Wireless Barricade Routers User Guide SMC7004AWBR V1.0

2 Hardware Installation Rear Panel 2.1 Panel Layout Front Panel LEDs monitor the status of each port. The rear panel features three 10/100 Mbps Ethernet ports and one Wide Area network (WAN) port. The WAN port connects your DSL or cable modem to the router. The LAN ports are used to connect to your computers or other network devices. Figure 2-1 Front Panel LED Figure 2-2 Rear Panel Ports LED Function Colour Status Description POWER Power indication Green On Power is being applied to this product. M1 System status 1 Orange Blinking This product is functioning properly. M2 System status 2 Orange On This product is working for a specific service. Blinking This product is being configured or upgraded. Don t turn it off! WAN WAN port activity Green On The WAN port is linked. Blinking The WAN port is sending or receiving data. W.LAN Wireless activity Green Blinking Sending or receiving data via wireless Link/Act. Link status Green On An active station is 1~3 connected to the corresponding LAN port. Blinking The corresponding LAN port is sending or receiving data. SPEED Data Rate Green On Data is transmitting in 1~3 100Mbps on the corresponding LAN port. Port RESET PRINTER COM WAN Port Port 1-3 Description To reset system settings to factory defaults, please follow the steps: 1. Power off the device, 2. Press the reset button and hold, 3. Power on the device, 4. Keep the button pressed about 5 seconds, 5. Release the button, 6. Watch the M1 and M2 LEDs, they will flash 8 times and then M1 flashes once per second. Printer Port (Optional) Serial port (connect dial-up modem or console cable) The port where you will connect your cable (or DSL) modem or Ethernet router. The ports where you will connect networked computers and other devices. DC IN Power inlet (DC 12V)

3 2.2 Procedure for Hardware Installation 1. Decide Where to Place Your Wireless Broadband Router: 3. Set up WAN connection: You can place your Wireless Broadband Router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your office (or your home) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to power and network connections. 2. Set up LAN connection: a. Wired LAN connection: connect an Ethernet cable from your computer s Ethernet port to one of the LAN ports of this product. b. Wireless LAN connection: make sure the antennae are in a vertical position. Connect an Ethernet cable from the WAN port to your cable/xdsl modem or Ethernet backbone. Figure 2-3 illustrates the WAN connection. 4. Power on: By connecting the power cord to the power inlet and turning the power switch on, this product will automatically enter the self-test phase. When it is in the self-test phase, the indicators M1 and M2 will be lighted ON for about 10 seconds, and then M1 and M2 will be flashed 3 times to indicate that the self-test operation has finished. Finally, the M1 will be continuously flashed once per second to indicate that this product is in normal operation. Figure 2-3 Setup of LAN and WAN connections for this product.

4 Configuring Your Computer with Windows 95/98/ME 4. Select the IP Address tab. Click Obtain an IP address automatically. 1. From the Windows desktop, click the Start button. Choose Settings, then Control Panel. 2. From Control Panel Double-click the Network icon. 5. Click the Gateway tab. If there are any Installed Gateways listed, highlight each one and click Remove. 3. In the Network window, under the Configuration tab, double-click the TCP/IP that is listed with your network card. 6. Click the DNS Configuration tab, and then select Disable DNS. Click the OK button.

5 7. Click the OK button in the Network window. Windows may copy some files, then will prompt you to restart your system. Click Yes and your computer will shut down and restart. 12.Clear all proxy settings: a. For Internet Explorer: i. Click Tools, then Internet Options. 8. Once your computer has restarted, click Start, and then Run ii.in the Internet Options window click the Connections tab. Next, click the LAN Settings button. 9. Type WINIPCFG and click OK. It may take a minute or two for the IP Configuration window to appear iii. Clear all the checkboxes. iv. Click OK, and then click OK again to close the Internet Options window. 10.From the drop-down menu, select your network card. Click Release and then Renew. Your IP Address should now be similar to the Barricade (i.e xxx). Click OK to close the IP Configuration window. b. For Netscape Navigator: i. Click Edit, then click Preferences 11.Open your web browser (i.e. Internet Explorer or Netscape Navigator).

6 ii. In the Preferences window, under Category double-click Advanced, then click Proxies. Select Direct connection to the internet. Click OK 2. Double-click the Network & Dial-Up Connections icon. 13.Repeat these steps for each Windows 95/98/Me computer connected to your Barricade 3. Double-click the icon that corresponds to the connection to your Barricade Configuring Your Barricade If you connect to the Internet using a: Cable Modem, turn to page 13 DSL Modem, turn to page 15 DSL Modem via PPP over Ethernet, turn to page Click Properties. Configuring Your Computer with Windows From the Windows desktop, click the Start button. Choose Settings, then Control Panel. 5. Double-click Internet Protocol (TCP/IP).

7 6. Select Obtain an IP address automatically and then select Obtain DNS server address automatically. Then click OK. Click OK or Close to close each window. 9.Type IPCONFIG /RENEW and press the <ENTER> key. Your IP Address should now be similar to the Barricade (i.e xxx). 7. From the Windows desktop, click the Start button, then Programs, then Accessories, and then click Command Prompt. 8. In the Command Prompt window, type IPCONFIG /RELEASE and press the <ENTER> key. 10.Type EXIT and press <ENTER> to close the Command Prompt window. 11.Open your web browser (i.e. Internet Explorer or Netscape Navigator). 12.Clear all proxy settings: a. For Internet Explorer: i. Click Tools, then Internet Options.

8 ii. In the Internet Options window click the Connections tab. Next, click the LAN Settings button. ii. In the Preferences window, under Category double-click Advanced, then click Proxies. Select Direct connection to the internet. Click OK. iii. Clear all the checkboxes and click OK. Click OK again to close the Internet Options window. 13.Repeat these steps for each computer connected to your Barricade. Configuring Your Barricade If you connect to the Internet using a: Cable Modem, turn to page 13 DSL Modem, turn to page 15 DSL Modem with a Log In name and Password, turn to page 17 b. For Netscape Navigator: i. Click Edit, then click Preferences

9 Configuring Your Barricade for a Cable Modem 5. Under WAN Type Click the Change button. 1. Open your web browser (i.e. Internet Explorer or Netscape Navigator). 2. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>. 6. Select Dynamic IP Address and click the Save button. 3. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 7. Key in your Host Name if your Internet Service Provider has given you one (i.e. CX A). 4. Click Primary Setup 8. Click Save, and then click the Reboot button. 9. When prompted to reboot now, click OK. 10.Once the Barricade is rebooted, you can surf the Internet as you normally would from all computers connected to it.

10 Configuring Your Barricade for a DSL Modem 1. Open your web browser (i.e. Internet Explorer or Netscape Navigator). 6. Select Static IP Address and click the Save button. 2. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>. 3. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 7. In the spaces provided, key in the values provided to you by your ISP. (Note: Enter the IP Address given to you in the WAN IP Address field, not the LAN IP Address field.) 4. Click Primary Setup 8. Click Save, and then click the Reboot button. 9. When prompted to reboot now, click OK. 5. Under WAN Type Click the Change button. 10. Once the Barricade is rebooted, you can surf the Internet as you normally would from all computers connected to it.

11 Configuring Your Barricade for a DSL Modem with a Log-In Name and Password 1. Open your web browser (i.e. Internet Explorer or Netscape Navigator). 6. Select PPP over Ethernet and click the Save button. 2. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>. 3. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 7. Key in your Account Name and Password in the appropriate fields. If your ISP has supplied you with a Service Name, enter it in the Service Name field; otherwise, leave it blank. 4. Click Primary Setup 8. Click Save, and then click the Reboot button. 9. When prompted to reboot now, click OK. 5. Under WAN Type Click the Change button. 10.Once the Barricade is rebooted, you can surf the Internet as you normally would from all computers connected to it.

12 Wireless Setting Installing and Configuring the Print Server If you are not connecting your printer to your Barricade, skip this section. 1. Insert the installation CD into the CD-ROM drive. The installation screen will automatically appear. (If it doesn t, please click Start, and then Run Then type <CD-ROM Drive> :\install.exe and click OK..) Wireless settings allow you to set the wireless configuration items. 1. Network ID (SSID): Network ID is used to identify the WLAN. Client stations can roam freely on this product and other Access Points that have the same Network ID. (The factory setting is default ) 2. Click the Install button. Follow the prompts on the screen. After rebooting your computer, the software installation is complete, but your computer must still be configured. 3. Click Start, click Settings, and then select Printers. 2. Channel: The radio channel number. The permissible number of channels depends on the Regulatory Domain. The factory setting is as follow: Channel 6 for North America; Channel 7 for European (ETSI); Channel 7 for Japan. 3. WEP Security: Select the data privacy algorithm you want. Enabling the security can protect your data while it is transferred from one station to another. The standardized IEEE WEP (128 or 64-bit) is used here. 4. Right click the printer connected to the Barricade, then click Properties. 4. WEP Key 1, 2, 3 & 4: When you enable the 128 or 64 bit WEP key security, please select one WEP key to be used and input 26 (for 128-bit) or 10 (for 64-bit) hexi-decimal digits.

13 Using the CD 5. Click the Details tab. 6. Under Print to the following port:, select PRTmate: (All-in-1). Insert the CD into your CD-ROM drive. The installation screen will automatically appear. (If it doesn t, please click Start, and then Run Then type <CD-ROM Drive> :\install.exe and click OK. ) 7. Click Port Settings. A. To install the print server software: Please refer to section Installing and Configuring the Print Server in this guide. Note: If you are not connecting your Barricade to a printer, you do not need to install the print server software. 8. Enter the Barricade IP Address (default is ) and click OK. 9. Click Spool Settings and, if available, select Disable bi-directional support for this printer and click OK B. To read the User Guide: Click on Read User Manual. (Note: you must have Adobe Acrobat Reader installed before viewing the manual. If you do not have it, you can install it from the CD. To install it, click Start, then Run and type <CD-ROM Drive>:\viewer\rs405eng.exe.) 10.Click OK to close the printer details window. 11.Your computer is now configured to print via the Barricade Print Server. Repeat these steps on each computer connected to the Barricade.

14 Troubleshooting Here are some things to try if, after following the steps in this guide, you still have problems with: 1. Open your web browser (i.e. Internet Explorer or Netscape Navigator). Connecting to the Internet How do I find out which WAN type to select? Use the following general rules to determine which WAN type your ISP uses: 2. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>. A. If your ISP has given you a specific IP Address, select Static IP. B. If use a Username and a Password to log in to your service, select PPP over Ethernet. C. If you use an external dial-up modem connected to your Barricade, select Dial-up Network. D. If your ISP has given you a host-name, select Dynamic IP Address. 3. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 4. Click Primary Setup I can t access the Internet through my Barricade. Depending on your Internet Service Provider (ISP), there are settings that you must change in order to connect to the Internet. A. If you subscribe to service and have a dynamic IP address, you will need to enter a host name. If your ISP does not require a host name, you must leave this field blank. To enter your host name: 5. Make sure WAN Type is set to Dynamic IP Address and enter the host name given to you by your ISP (i.e. CX123456).

15 6. Click Save and then click Reboot. 7. When prompted to reboot now, click OK. B. Your ISP may require a domain name. If your ISP does not require a domain name, you must leave this field blank. To enter your domain name: 5. In the Domain Name field, key in the domain name given to you by your ISP (i.e. xxx.yyy.home.com). 1. Open your web browser (i.e. Internet Explorer or Netscape Navigator). 6. Click Save and then click Reboot. 2. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>. 3. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 7. When prompted to reboot now, click OK. C. You may need to have your Barricade clone the MAC address of your Ethernet adapter. Your ISP may register your MAC address (a MAC address is a serial number that is unique to every Ethernet adapter), and your Barricade needs to pass on that address to your ISP. To do so: 1. Make sure that you are using the computer and Ethernet adapter that was originally connected to your ISP. 4. Click DHCP Server. 2. Open your web browser (i.e. Internet Explorer or Netscape Navigator). 3. In the Location field (for Netscape) or Address field (for Internet Explorer), type and press <ENTER>.

16 4. In the System Status page of the Barricade web console, type your password in the System Password field (default is admin ) and click the Log In button. 5. Click Toolbox. D. If you use DSL, you may need to reconfigure your Barricade for a PPPoE connection (Point to Point Protocol over Ethernet). To reconfigure, go to the section labeled Configuring Your Barricade for a DSL Connection with a Log-In Name and Password on page 19. E. If you use a totally plug and play ISP (i.e. Time Warner or Road Runner in some areas) you may need to shut down and restart your cable modem after you ve finished configuring the Barricade. Reading the Manual When I click on User s Manual when the CD starts up, nothing happens 6. Click the Clone MAC button. You may need to install the viewer first. To install the viewer software: 1. Double-click the My Computer icon on your Windows desktop. 7. Click Save and then click Reboot. 2. Right-click the CD-ROM icon and select Explore. 3. Double-click the viewer folder. 8. When prompted to reboot now, click OK.

17 4. Double-click the file RS405ENG.EXE. This will start the installation of the viewer software. Follow the screen prompts to complete the installation. 5. When the installation program is finished, remove and reinsert the CD, and then click the User s Manual button.