Ultra-Fast Fully Insulated FASTON* Receptacle Terminals

Transcription

1 Product Specification Mar11 Rev D Ultra-Fast Fully Insulated FASTON* Receptacle Terminals 1. SCOPE 1.1. Content This specification covers the perform ance requirem ents for Ultra-Fast fully insulated FASTON* receptacle terminals. These term inals consist of a FASTON receptacle body enclosed in a fully insulated housing. They mate with FASTON tabs on devices used in home entertainment centers, business m achines, copying equipm ent, com puter peripherals, appliances and other com m ercial equipm ent 1.2. Qualification W hen tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be perform ed using the applicable inspection plan and product drawing. 2. APPLICABLE DOCUM ENTS The following docum ents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the requirem ents of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirem ents of this specification and the referenced docum ents, this specification shall take precedence TE Connectivity (TE) Docum ents! 109-1: General Requirements for Test Specifications! 109 Series: Test Specifications as indicated in Figure 1! : Application Specification 2.2. Com m ercial Standards! CSA C22.2 No 153: Quick-Connect Term inals! DIN VDE 0627: Connectors and Plug-And-Socket Devices! UL 310: Quick-Connect Term inals, Standard for 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing Materials! Receptacle body: Brass or phosphor bronze, tin plated! Housing: Nylon type 6/6, UL 94V-2! Tabs (for test purposes): Brass, tem per 2, CDA alloy! W ire (for test purposes): Complies with UL 310 Paragraph 7, 600 Volt rating 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved Indicates change *Trademark For latest revision, visit our website at For Regional Customer Service, visit our website at TE logo is a trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC B 1 of 5

2 Ratings! Voltage: 600 volts AC m axim um! Operating Tem perature: 105 C m axim um 3.4. Performance and Test Description Product is designed to m eet the electrical, m echanical and environm ental perform ance requirem ents specified in Figure Test Requirem ents and Procedures Sum m ary Test Description Requirem ent Procedure Exam ination of Product. Test Condition A. Test Condition C. Receptacle, Tab Entry Position. Meets requirem ents of product drawing and Application Spec ELECTRICAL No breakdown or flashover when 3400 volts AC are applied for 1 minute. No breakdown or flashover at rear of terminal when 3000 volts AC are applied for 1 minute. Term inal Applied Size Voltage (volts AC) No breakdown or flashover, 1 m inute hold. Heating (Tem perature Rise). W ire Size Current (am peres) (AW G).110 Others C maximum temperature rise. Figure 1 (continued) TE Spec Visual, dim ensional and functional per applicable inspection plan. UL 310, 600 Volt Rating. Test wired terminals in Number 12 lead shot. UL 310, 600 Volt Rating. Test on flat metal plate. See Figure 4. TE Spec Test wired terminals on a flat metal plate. See Figure 5. Stabilize at specified current and m easure tem perature rise. Rev D 2 of 5

3 Test Description Requirem ent Procedure Heat Cycling (Current Cycling). W ire Size Current (am peres) (AW G).110 Others C maximum temperature rise. Ä Temperature rise between 24 and 500 cycles shall not exceed 15 C on any conductor. MECHANICAL Pull Out (Crimp Tensile). W ire Size Tensile (AW G) (Lbs minimum) Above values are less than m axim um withdrawal force. See Figure (Unassem bled). (Assem bled). Engagem ent-disengagem ent (Engaging-Separating). Heat Age, 136 C. Heat Age/Hum idity. No separation of the insulation from the term inal body. No separation of the insulation from the term inal body Subject sam ples to 500 current cycles of 45 minutes ON and 15 m inutes OFF. Apply a direct and gradual pull at a rate of 1 inch per minute, 1 minute hold at specified load. Subject unwired terminals to a 3 pound pull between the insulation and terminal for 1 minute. Subject wired terminals to a 6 pound pull between the insulation and terminal for 1 minute. See Figure 2. Engage and disengage term inals and tabs 6 times. ENVIRONMENTAL Meet Dielectric W ithstanding Voltage, Test Condition A; and (assem bled and unassembled). Meet Dielectric W ithstanding Voltage, Test Condition A. Figure 1 (end) Subject terminals to 136 C for 7 days. Subject unwired terminals to 100 C for 7 days followed by 85% RH at 30 C for 24 hours. Rev D 3 of 5

4 Tab Size (Plain Brass).250 Term inal Plating First Insertion (max) (max) Force (pounds) First W ithdrawal Average Sixth W ithdrawal Average /.187 Tin Term inal Tests and Sequences Figure 2 Engagem ent and Disengagem ent Forces Test or Exam ination Test Group (a) Test Sequence (b) Exam ination of Product Test Condition A Test Condition C Receptacle, Tab Entry Position Heating (Tem perature Rise) 2 Heat Cycling (Current Cycling) 3 Pull Out (Crim p Tensile) 3 (Unassem bled) (Assem bled) Engagem ent-disengagem ent (Engaging-Separating) 2 3 3(c) (c) Heat Age, 136 C 2 2 Heat Age/Hum idity NOTE (a) (b) (c) See paragraph 4.1.A. Numbers indicate sequence in which tests are performed. Uncrimped terminals and wires in test groups 4 and 11 shall be conditioned in the environments indicated. After conditioning, each sample is crimped to the appropriate wire and the electrical or mechanical test is performed. Figure 3 Rev D 4 of 5

5 QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Sam ple Selection Term inals and tabs shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test groups 1, 2, 3 and 4 shall each consist of 20 samples of each wire size and terminal type per group. Test groups 5, 6, 7, 8, 9, 10, 11 and 12 shall each consist of 20 samples of each terminal type per group. All samples to be terminated shall be crim ped to appropriate tin plated test conductors. B. Test Sequence Qualification inspection shall be verified by testing sam ples as specified in Figure 3. C. Acceptance 1. Requirements put on the test samples, as indicated in the Requirements portion of Figure 1, exist as either the upper or lower statistical tolerance lim it (95% confidence, 98% reliability). All sam ples tested in accordance with this specification shall m eet the stated tolerance lim it. 2. Failures attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. W hen product failure occurs, corrective action shall be taken and samples resubm itted for qualification Quality Conformance Inspection The applicable inspection plan will specify the sampling acceptable quality level to be used. Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing and this specification Certification This product has been recognized under the Component Recognition Program of Underwriters Laboratories Inc., Electrical File Num ber E and certified by Canadian Standards Association File Numbers LR Also, VDE Testing and Certification Institute, Reference No. 4751_1431_1047. Figure 4 Figure 5 Metal Plate Test Fixture Tab, Receptacle Entry Position Rev D 5 of 5

6

7