OVERKRETE E-100 S. 100% Solids, High Gloss Epoxy Floor CoatingTechnical
|
|
- Gervase Randall
- 7 years ago
- Views:
Transcription
1 Data OVERKRETE E-100 S OVERKRETE XTRA E-100 S 100% Solids, High Gloss Epoxy Floor CoatingTechnical PRODUCT DESCRIPTION The E-100 S are floor coating systems applied at a thickness of 16 to 50 mils. They are designed for long term protection of concrete in light to medium service areas. They protect against intermittent chemical spills, splashes and power washings and have excellent abrasion resistance against foot and rubber covered wheel traffic. These coatings provide a mil anti-skid textured surface, or a 16 mil smooth finish. For added gloss and color retention use OVERKRETE XTRA E-100 S. E-100 S Coatings are virtually 100% solids copolymer resin systems. The low viscosity and self leveling properties permit easy application followed by squeegee rolling with a short nap roller. They can also be rolled on to vertical surfaces using OVERKRETE E-100 V or OVERKRETE XTRA E-100 V. E-100 S Coatings are available in ten aesthetically pleasing colors. Special colors and surface texture are available upon request. CORROSION RESISTANCE E- 100 S Coatings are resistant to a wide range of chemicals. Due to the thinness of these coatings, they are not recommended for continuous or prolonged exposure to chemicals. For more detailed chemical resistance information, refer to the Product Recommendation Guide. TYPICAL USES E-100 S Coatings are used where one or more of the following properties are required: Splash & Spill corrosion resistance High wearability Anti-slip safety surfaces (when used in conjunction with broadcast aggregates) Elimination of concrete dusting Aesthetically pleasing surfaces Easy cleanup and maintenance Color stability with the Xtra E-100 Either product may be used directly over concrete, or as a topcoat for other Rust- Oleum toppings. E- 100 S may be used as a glaze coat over the Overkrete 1/4" topping. For use with FlorClad system, FlorClad HD must first be coated with OVERKRETE E-100 OP or OVERKRETE XTRA E-100 OP. The OVERKRETE E-100 S and OVERKRETE XTRA E-100 S may then be applied over the E-100 OP. For improved color and gloss retention use the OVERKRETE XTRA E-100 S. TYPICAL OVERKRETE E-100 APPLICATIONS Walkways Light warehousing Light storage areas Light manufacturing Permanent marker lines Show rooms OSHA Yellow walkway lines Clean rooms Boiler plants Laboratories Animal Treatment Areas Parking Lots INDUSTRIAL and COMMERCIAL APPLICATIONS Electronics Industry Overkrete E-100 S, Overkrete Xtra E-100 S Bulletin Page 1
2 Power Plants Automotive Assembly Automotive Showrooms Airport Baggage Handling and Ramps Wineries Breweries Bottling Industries Beverage Industries Chemical Plants Meat Packing and Poultry Plants Dairies Food Processing Plants Bakeries Schools Hospitals Pharmaceutical and Chemical Laboratories Restaurants FORM TB9810 Rev. 6/98 Overkrete E-100 S, Overkrete Xtra E-100 S Bulletin Page 2
3 packaging, application, coverage, clean-up Industrial Lunchrooms and Dressing Rooms Waste Water Treatment Plants Fire Stations APPLICATION THICKNESS E-100 S coatings have a tenacious adhesion to concrete. They will not lift or crack under static or dynamic loads unless the underlying concrete fails. Concrete failure is evidenced by powdering, crazing, spalling or cracking. E- 100 S Coatings cushion the concrete from failing. This cushioning effect increases in proportion to the thickness of the coating applied. Light to medium duty service requires a 16 mil (smooth) or mil (antiskid) coating. This is the range that these coatings are designed to handle most economically. For heavier duty service refer to OVERKRETE, OVERKOTE, and OVERKOTE PLUS Technical Bulletins. PACKAGING The E-100 S coatings are packaged in two kit sizes: Overkrete E-100 S Overkrete Xtra E-100 S 1 gallon 1 gallon 4 gallon 3 gallon Mixing ratios are listed on the product labels. Silica is not packaged with the standard units. SURFACE PREPARATION AND APPLICATION Concrete must be sound, clean, and visibly dry. Voids in the concrete should be filled. The surface should be sand blasted, shot blasted, or acid etched prior to application. Concrete, ambient, and material temperatures should be F at time of application. Concrete must be visibly dry at time of application. OVERKRETE E-100 S & OVERKRETE XTRA E-100 S do not require a primer or sealer. However, when applying a smooth 16 mil finish, a primer must be used to help ensure a smooth finish. Apply with a squeegee followed by a short nap roller. Refer to PRIME AND SEAL PRIMER technical bulletin. NOTE: Surface preparation and application procedures are described in more detail in the Application Instructions. These should be read before use. COVERAGE (coverage rates will vary depending on surface texture) 16 mils Smooth Finish - applied in two coats. 1st Coat sq ft per gal (5-8 mils) 2nd Coat sq ft per gal (8-12 mils) mils Anti-skid Finish - applied in two coats. (three steps involved) 1st Coat 100 sq ft per gal (16 mils; no less) while wet 2nd Coat* Aggregate broadcast 100 sq ft per gal** * The 2nd coat anchors the aggregate. ** This will vary, based on coarseness of aggregate used. Equal coverage may be expected when used as a glaze coat over Overkrete topping. SET TIME Cured adequately for next coating step in 8-10 hours at 70 F. Overkrete E-100 S, Overkrete Xtra E-100 S Bulletin Page 3
4 clean-up, safety CLEAN UP Xylene can be used to remove OVERKRETE E-100 S and OVERKRETE XTRA E-100 S Coatings from equipment and tools before they begin to harden; otherwise strong solvents such as methylene chloride will be required. Refer to Material Safety Data Sheet (MSDS) for clean up materials to ensure safe use. SAFETY E- 100 S Coatings contain amine curing agents. Avoid skin contact. In case of eye contact or ingestion, contact a physician immediately. In case of skin sensitivity to these materials, use protective clothing and gloves. MATERIAL SAFETY DATA SHEETS See Material Safety Data Sheet and label warnings for safety information. It is strongly recommended that they be read by all persons handling OVERKRETE E-100 S and/or OVERKRETE XTRA E-100 S. If there are any questions on the use of this product, please consult our technical service department. Overkrete E-100 S, Overkrete Xtra E-100 S Bulletin Page 4
5 The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith. The statements of this literature do not constitute a warranty, express or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All technical information is subject to change without notice. physical strength characteristics Property Typical Value Test Method Compressive Strength 7,900 psi ASTM C 579 Flexural Strength 3,700 psi ASTM D 790 Tensile Strength 3,900 psi ASTM D 638 Taber Abrasion with 1000 g load ASTM D 4060 CS 17 Wheels Loss/1000 Cycles = 30 mg Hardness, Shore D 85 ASTM D 2240 Overkrete E-100 S, Overkrete Xtra E-100 S Bulletin Page 5
STERI-SOFT HIGH FOOT TRAFFIC, ULTRAVIOLET RESISTANT, URETHANE RESILIENT FLOORING SYSTEM, 1/8 GREEN BUILDING FEATURES TYPICAL APPLICATIONS
GREEN BUILDING FEATURES * Steri-Soft contributes toward satisfying credit EQ 4.2 under LEED. 100% Resilient Flooring Low emitting material Contains 27% post consumer recycled product Processed and manufactured
More informationRAPTOR TRUCK BED LINER - BLACK
4 x 750ml RAPTOR base coating x L RAPTOR hardener TECHNICAL DATA SHEET & U-POL s RAPTOR Truck Bed Liner is a durable K polyurethane coating that provides surfaces with a protective barrier. RAPTOR Tintable
More informationARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials
ARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials SECTION 03 92 50 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
More informationSC2000 CEMENT BONDING PROCEDURES
Pg.1 SC2000 CEMENT BONDING PROCEDURES Widely recognized as the world s finest cold vulcanizing cement REMA SC2000 is the solution to your industrial bonding problems. By using REMA UTR20 hardener with
More informationCORROSION ENGINEERING RESIN-BASED POLYMER CONCRETES AND GROUTS
AN ERGONARMOR COMPANY TECHNICAL INFORMATION SPECIFICATION FOR INSTALLATION 07/11 SUPERSEDES 04/00 PAGE 1 OF 6 CORROSION ENGINEERING RESIN-BASED POLYMER CONCRETES AND GROUTS 1. SCOPE 1.1 This specification
More information738-B-297 POLYMERIC CONCRETE BRIDGE DECK OVERLAY. (Adopted 02-20-14)
POLYMERIC CONCRETE BRIDGE DECK OVERLAY (Adopted 02-20-14) Description The polymeric concrete bridge deck overlay shall consist of an epoxy polymer that acts together with special aggregate to form an overlay
More information09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS
09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS PDS SE-160 01-2006 1. PRODUCT NAME SE-160 Clear Surface Coating (water-based copolymer) Specialty Elastomeric Topcoat 2. MANUFACTURER
More informationColorado State University. Durrell Center Roof Repair
Colorado State University Durrell Center Roof Repair SPECIFICATION: POLYURETHANE FOAM ROOFING l.0 GENERAL REQUIREMENTS The successful application of a polyurethane foam roofing system is dependent upon
More informationMARTIN TESTING LABORATORIES (MTL) PAINTS AND COATINGS TESTING CAPABILITIES
Liquid Coating Properties Composition VOC Content, ASTM D2369 Water Content, ASTM D4017 Physical Properties Calculating Physical Constants of Coatings, ASTM D5201 Density, ASTM D1475 Flash Point, ASTM
More informationExternal Wrapping of Steel Riser Pipe. Case Study HJ3 CS200902
External Wrapping of Steel Riser Pipe Case Study HJ3 CS200902 Introduction Refineries process a wide variety of petroleum products. As part of the process, they rely on cooling towers, which recycle water
More informationScotch-Weld TM. Epoxy Adhesive 1838 B/A Green 1838 B/A Tan 1838-L B/A Translucent. Technical Data February, 2016. Product Description
3 Scotch-Weld TM 1838 1838 1838-L Technical Data February, 2016 Description 3M TM Scotch-Weld TM s 1838 and are controlled flow products; Scotch-Weld 1838-L is flowable. These epoxy adhesives are two-part,
More informationConcrete Repair. Applications and Procedures
Concrete Repair Applications and Procedures Objectives Identify what surface preparation is needed Identify typical modes of failure and testing methods How to choose the correct material for the repair
More informationPRODUCT DATA SHEET DESCRIPTION:
DESCRIPTION: SP-9888 Pipe Lining is based on the latest Zero VOC Novolac Technology. The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance.
More informationPRODUCT DATA SHEET Sika Cable System
PRODUCT DATA SHEET Corrosion protection for bridge cables of steel and galvanized steel PRODUCT DESCRIPTION The Sika Cable System consists of coating materials as well as a sealing respectively injection
More informationNote: Minor color change may occur in exposed service, but corrosion protection will not be compromised
DESCRIPTION One component, high-build heat-resistant inert multipolymeric matrix coating to prevent corrosion under insulation (CUI) of carbon and stainless steel to temperatures ranging up to 650 C (1200
More informationSECTION 03 54 00 RESURFACING CAST IN PLACE CONCRETE
Page 1 SECTION 03 54 00 RESURFACING CAST IN PLACE CONCRETE Specifier Notes: This guide specification is written according to the Construction Specifications Institute (CSI) format. The section must be
More informationProperty Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1. 212 F (100 C) calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Not approved 2063;2064 1,2 2063 ^(ValidationDate) 1 Product description This is a two component solvent free polyamine cured coating. It is a general purpose tank lining with good chemical resistance.
More informationEpoxy Curing Agents and Modifiers
Epoxy Curing Agents and Modifiers 2489 Curing Agent DESCRIPTION 2489 curing agent is a low-color cycloaliphatic amine adduct intended for use with liquid epoxy resins. It has a very low viscosity which
More informationAcrylic Enamel Topcoat
Acrylic Enamel Topcoat ACRYL-GLO TECHNICAL DATA SHEET The ACRYL-GLO single-stage acrylic enamel paint system provides a durable finish that is easy to apply and suitable for both commercial and passenger
More informationCA-48 TECHNICAL SPECIFICATION
CA-48 TECHNICAL SPECIFICATION SafeLane surface overlay Pavement Substrate A Cargill Deicing Technology Product Providing customers with deicing solutions that save lives and enhance commerce. Helping to
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 27 C calculated IED (2010/75/EU) (calculated)
Approved 402;2521 1 2521 zinc epoxy ^(ValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationSECTION 03 35 43 POLISHED CONCRETE FINISHING
SECTION 03 35 43 POLISHED CONCRETE FINISHING PART 1 - GENERAL 1.01 SUMMARY A. Provide polished concrete finishing system where indicated on drawings, complete. This section includes the following: 1. Concrete
More informationINDUSTRIAL FLOORING INSTALLATION CHALLENGES. James C. Ziegler, ArmorSeal Product Manager Sherwin Williams Cincinnati, Ohio, USA
INDUSTRIAL FLOORING INSTALLATION CHALLENGES James C. Ziegler, ArmorSeal Product Manager Sherwin Williams Cincinnati, Ohio, USA Abstract: Specifier's and contractors not only need to properly evaluate the
More informationSECTION 12. Surface Retarders. Sec 12 TECHNICAL DATA SHEET. Surface Retarders. Face-Off... 12-3 Top Cast... 12-5. American Owned American Made
SECTION PRODUCT PAGE Face-Off... -3 Top Cast... -5 American Owned American Made -1 Face-Off Surface Protectant PRODUCT DESCRIPTION Face-Off is an innovative surface protectant designed to keep splatter,
More informationPHOENIX 370-120 Product Data Sheet (Updated on 14-Jan-2012) www.phoenixasia.com.hk
DESCRIPTION A water borne thin film intumescent coating for the fire protection of structural steelwork. PRODUCT FEATURES AND RECOMMENDED USES Provides up to 120 minutes fire resistance to structural steelwork.
More informationDocument Library TS Data Sheet 46012 46013 46014
Document Library TS Data Sheet 46012 46013 46014 Rev:2 Effective: 01/11/2002 3M Marine High Strength Repair Filler Data Sheet Status: Active 3M Part No.(s) 46012 46013 46014 3M Part Descriptor(s) Pint
More informationSECTION 623 CONCRETE BONDING COMPOUND, EPOXY MORTAR AND EPOXY POLYMER CONCRETE OVERLAY SECTION 623.10 CONCRETE BONDING COMPOUND.
SECTION 623 CONCRETE BONDING COMPOUND, EPOXY MORTAR AND EPOXY POLYMER CONCRETE OVERLAY SECTION 623.10 CONCRETE BONDING COMPOUND. 623.10.1 Description. This work shall consist of preparing the surface,
More informationTECHNICAL REQUIREMENTS AND SPECIFICATIONS
TECHNICAL REQUIREMENTS AND SPECIFICATIONS REHABILITATION OF CONCRETE AND MASONRY MANHOLES OR UNDERGROUND VAULTS WITH A PROTECTIVE COATING (As Provided by Raven Lining Systems) FOREWORD This specification
More informationSummit Racing Equipment s Paint and Auto Refinishing System was developed specifically for the home enthusiast and small shop owner wanting a
Summit Racing Equipment s Paint and Auto Refinishing System was developed specifically for the home enthusiast and small shop owner wanting a professional-looking paint job for hundreds of dollars less
More informationSIGMACOVER 300. PRODUCT DATA SHEET December 12, 2014 (Revision of November 1, 2013) DESCRIPTION
DESCRIPTION Two-component, high-build, polyamine adduct-cured, coal tar epoxy coating PRINCIPAL CHARACTERISTICS Outstanding (sea)water resistance (outside hull and ballast tanks) Outstanding water- and
More informationEpoxy Floor Coating Problem Solving Guide
Table of Contents: Page: Troubleshooting Issue: 2. Color Differential 3. Fish Eye 4. Milky or Cloudy Coatings 5. Orange Peel 6. Peeling or Delamination 8. Delamination between Coats 9. Pinholes/Bubbling
More informationTECHNICAL DATA RS-6100. European Clear EZ. 5751 N. Webster Street Dayton, OH 45414-0802 Phone 937-890-6547 Toll Free 800-257-6547 Fax 937-890-6320
RS-6100 TECHNICAL DATA European Clear EZ DESCRIPTION: RS-6100 European Clear EZ is formulated with premium European resins. It is ideal for excellent color matching on white, light colors and metallics
More informationSMOOTHMOVE INSTRUCTIONS FURNITURE VAN EPOXY FLOOR FINISH KIT VOC-FREE - NO SOLVENT GENERAL INFORMATION KEY 87269AB
SMOOTHMOVE INSTRUCTIONS FURNITURE VAN EPOXY FLOOR FINISH KIT VOC-FREE - NO SOLVENT GENERAL INFORMATION KEY 87269AB YOU ARE NOW GETTING READY TO USE SOLVENT FREE AND 100% SOLIDS HIGH GLOSS SMOOTHMOVE FOR
More informationProperty Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 34 C IED (2010/75/EU) (calculated)
408;21800;21820;21740;21760;21840 1,2 408 unsaturated vinyl ester ^(ValidationDate). 1 Product description This is a glass flake reinforced unsaturated vinyl ester coating. It is an ultra high build, extremely
More informationResurfacing Concrete. Page 1 of 5
Resurfacing Concrete Materials List QUIKRETE Concrete Resurfacer (No. 1131) (see calculator on page 5 for quantity needed) QUIKRETE Concrete and Stucco Wash (No. 8601) QUIKRETE Concrete Sealer (No. 8800)
More informationDivision 9. SignaFlor Pad and Pour Flooring System
Division 9 SignaFlor Pad and Pour Flooring System SPECIFICATIONS Page 1. General... 2 1.1 Description 2 1.2 Quality Assurance 2 1.3 Submittals 2 1.4 Delivery and Storage 3 1.5 Warranty 3 1.6 Working Conditions
More informationEpoxy Curing Agents and Modifiers
Epoxy Curing Agents and Modifiers Ancamine 2432 Curing Agent Technical Datasheet DESCRIPTION is a modified aliphatic amine intended for use with liquid epoxy resins. imparts very rapid development of physical
More informationSECTION 32 1816 PLAYGROUND SURFACING TILES
SECTION 32 1816 PLAYGROUND SURFACING TILES PART 1 GENERAL 1.01 SECTION INCLUDES A. Resilient playground safety surfacing tiles. B. Coordinate with work shown in other sections so the work is installed
More informationConcrete Resurfacing. System Guide. by Parchem Construction Supplies
Concrete Resurfacing System Guide by Parchem Construction Supplies Resurfacing Spray-on resurfacing is a 2-3mm topping applied to structurally sound concrete surfaces that are at least 28 days old. Resurfacing
More informationSCENIC VIEW SV 10 SECTION 08 87 13 SOLAR CONTROL FILMS
PART 1 GENERAL SCENIC VIEW SV 10 SECTION 08 87 13 SOLAR CONTROL FILMS 1.1 SUMMARY A. Optically clear dual reflective, neutral sputtered and aluminum metallized polyester film for solar control. 1.2 RELATED
More information07 21 19 Guide Specification STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM
07 21 19 STAYFLEX CORROSION CONTROL AND THERMAL INSULATION SYSTEM 7819 Broadview Road Cleveland, OH 44131 800-522-4522 February, 2011 SPEC NOTE: This guide specification is intended for use when specifying
More informationIS800 Series. Technical Data Sheet IS802, IS803, IS808, IS800.09. Description. Key Features and Benefits. Typical Physical Properties
1810.html Technical Data Sheet IS800 Series IS802, IS803, IS808, IS800.09 Description IS802, IS803, IS808 and IS800.09 one-component, ready-to-use silicone adhesive sealants have a paste-like consistency
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 735;739 1 735 phenolic/novolac epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is a specially designed tank lining with
More informationTecnoepo Flooring System 185
Certificate ICMQ 1305-CPD-0808 Approved Standard EN 1504-2 prospect ZA.1f Direttive 89/106/CEE TECNOCHEM E LEED LEED Leadership Energy Environmental Design THE PRODUCTS: Primer TECNOFIX EP 110 Primer two-component
More informationcement Masonry Cement Engineered for quality and reliability, Lafarge cements for masonry deliver consistent performance. page 2 Lafarge Cement
cement Masonry Cement Engineered for quality and reliability, Lafarge cements for masonry deliver consistent performance. page 2 Lafarge Cement Lafarge in North America The Lafarge Group is the world leader
More informationDuPont ChromaOne Acrylic Urethane Single Stage
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaOne is a productive acrylic urethane designed for spot, panel and overall repairs of OEM Single Stage finishes, both solids and
More informationCrystal Clear Sealant
Crystal Clear Sealant Technical Data February, 2012 Product Description 3M Crystal Clear Sealant is a one component thermoplastic elastomer which forms permanent elastic bonds when used in surface sealing
More informationSection 03 35 43 Polished Concrete Finishing. Vexcon
SS 120 1-13 Section 03 35 43 Polished Concrete Finishing Specifier Note: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-part format. This section
More informationT R A N S F E R A B L E F U L LY
HSTOPS A WALL OF WATER 22 FT. HIG! F U L LY T R A N S F E R A B L E RESISTS10 PSI ! 1 F U L LY T R A N S F E R A B L E HSTOPS A WALL OF WATER 22 FT. HIG RESISTS10 PSI Guaranteed To Stop Water Even Under
More informationWESTERN COOL ROOF SYSTEMS Sustainable - Energy Efficient FLUID APPLIED REINFORCED ROOF SYSTEM
WESTERN COOL ROOF SYSTEMS Sustainable - Energy Efficient FLUID APPLIED REINFORCED ROOF SYSTEM SPECIFICATION NO. SMAA-2P-8xE UPGRADE SMOOTH SURFACE / CAP SHEET / SINGLE PLY 2 PLY POLYESTER REINFORCED ACRYLIC
More informationSIGMAFAST 210. PRODUCT DATA SHEET December 12, 2014 (Revision of April 1, 2013) DESCRIPTION
DESCRIPTION Two-component, high-build zinc phosphate polyurethane primer/finish PRINCIPAL CHARACTERISTICS Specially designed for in-shop application Fast-curing Easy application by airless spray Unlimited
More informationAdhesive Recommendation for Altro Flooring. Porous (absorbent) subfloors (most wood subfloors and some concrete)
Adhesive Recommendation for Altro Flooring Product Safety Sheet Flooring Smooth Sheet Flooring Porous (absorbent) subfloors (most wood subfloors and some concrete) Altrofix 30/31 (excessively heavy rolling
More informationAdditional Information. Paint Application
Additional Information Paint Prepared by: International Paint Ltd. www.international-pc.com The information in this guideline is not intended to be exhaustive; any person using the product for any purpose
More informationRESTORE 10X Advanced Resurfacer FAQs Page 1 of 11
Page 1 of 11 FEATURES & BENEFITS Q. Is the new Restore 10X Advanced Resurfacer replacing the first generation of Restore 10X? A. Yes, the new Restore 10X Advanced Resurfacer will replace the first generation
More informationWaterproofing System for Wastewater Tanks in Petrochemical Industries and Refineries
Waterproofing System for Wastewater Tanks in Petrochemical Industries and Refineries Introduction Wastewater of petrochemical industries and refineries contains high amounts of emulsified aliphatic or
More informationConstruction. 3-part thixotropic epoxy patching mortar. Product Description. Tests
Product Data Sheet Edition 05/12/2014 Identification no: 020204030010000044 Sikadur -41 CF Rapid 3-part thixotropic epoxy patching mortar Construction Product Description Uses Characteristics / Advantages
More informationBUILT-UP ROOF COATING SMOOTH and GRANULE SURFACE SPECIFICATION
07560 BUR BUILT-UP ROOF COATING SMOOTH and GRANULE SURFACE SPECIFICATION PART 1: GENERAL 1.01 SCOPE: To extend the useful service life of the aged or new asphalt built-up roof system and to reduce cooling
More informationSelecting Vinyl Flooring
extension.usu.edu Smart Shopping for Home Furnishings Selecting Vinyl Flooring Dr. Leona Hawks Home Furnishings & Housing Specialist 1987 HI 03 Shopping for vinyl? There are many different varieties of
More informationFabcograte FRP Grating. Tolerances: ±1/16. Tolerances: ±1/16. THICKNESS BAR SPACING PANEL SIZE (FT.) WT (LBS) 1" 1.5" x 1.
Features: Will not rust. Corrosion resistant. Non-sparking. Fire retardant. Non-conductive. Maintenance free. Molded-in color. Light weight. Easy to install. Impact resistant. Quality appearance. Fabcograte
More informationBENTLEY ELEMENTS COLLECTION LVT
This document refers to the following products: Product Size Installation direction Seams treatment Elements Tiles See specifications 90 None Elements Planks See specifications Stair Step None Note: This
More informationFLOOR TREATMENT 09610
14805 E. Moncrieff Place Aurora, CO 80011 Phone: (800) 872-5515 Phone: (303) 371-1411 Fax: (303) 371-6958 E-mail: gerry.mueller@bona.com www.bonakemi.com This MANU-SPEC utilizes the Construction Specifications
More informationSECTION XXXXXX TECHNICAL SPECIFICATIONS FOR INSTALLATION OF PROTECTIVE COATINGS FOR MANHOLES, WETWELLS, AND OTHER SANITARY SEWER STRUCTURES
1.00 PART 1 GENERAL 1.01 SCOPE A. It is the intent of this contract to install a 100% solids epoxy monolithic coating to the walls, benches and inverts of all manholes and the specified surfaces of other
More informationTractor Painting Tips
Keeping your tractor or equipment well kept & free from rust & corrosion will extend the life of your investment & help retain its value for a longer period of time. It can be difficult, in many cases,
More informationMETAL ROOF RESTORATION SAMPLE DESIGN GUIDELINES
METAL ROOF RESTORATION SAMPLE DESIGN GUIDELINES REFLECTICLEAN ACRYLIC/URETHANE Elastomeric Roofing Systems, Inc 6900 Bleck Dr. Rockford, MN 55373 800.403.7747 -or- 763.565.6900 fax: 763.565.6901 email:
More information3 Scotch-Weld TM. Epoxy Adhesive DP110 Translucent and Gray. Technical Data December, 2009
3 TM Technical Data December, 2009 Product Description 3M are two-part epoxy adhesives which combine a fast cure with flexibility. Features Controlled flow 20 minute handling strength Duo-Pak cartridge
More informationProduct Information. D8115 Matte and D8117 Semi-Gloss Clearcoat System
Product Information D8115 Matte and D8117 Semi-Gloss Clearcoat System Product Description D8115 Matte and D8117 Semi-Gloss Clearcoats are designed for use over Envirobase High Performance Waterborne, Global
More informationSaint Gobain Gyproc India Ltd. (Formerly India Gypsum Ltd.)
Saint Gobain Gyproc India Ltd. (Formerly India Gypsum Ltd.) Gyproc Plasters The cracks in cement sand plaster are an inherent feature which cannot be completely prevented but can only be controlled and
More information10P20-44 High Solids Epoxy Primer
Technical Data Sheet Product Group High solids epoxy primer Characteristics Product Information A high solids urethane compatible, Skydrol resistant primer for the exterior of aircraft. It provides excellent
More informationWecryl Waterproofing System under surfacing supplied by others
Brief description The Wecryl waterproofing system allows a high-quality, seamless and crack-bridging waterproofing layer to be installed under loose-laid or bonded surfacing supplied by others (stone slabs,
More informationBRIDGE FIELD PAINTING, REPAINTING, 412 AND PAINT RESIDUE CONTAINMENT. A. Field Painting, Bridge Repainting and Residue Containment:
412.1 DESCRIPTION BRIDGE FIELD PAINTING, REPAINTING, 412 This specification contains the requirements for the removal, containment, and disposal of existing paint on steel surfaces, preparing the steel
More informationApproved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 30 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Approved 3140;3240;4320 1,2 3140 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a glossy finish with very
More information09 67 00/STO BuyLine 4352. Resinous Floor Systems
09 67 00/STO BuyLine 4352 Resinous Floor Systems Seamless Solutions Good Designs Don t Just Happen They are created using innovative, practical solutions that are both design worthy and cost-effective.
More informationSECTION 07560 FLUID APPLIED ROOFING (LIGHT TRAFFIC DECKS OVER CONCRETE)
SECTION 07560 FLUID APPLIED ROOFING (LIGHT TRAFFIC DECKS OVER CONCRETE) PART 1 GENERAL 1.1 DESCRIPTION 1. Fluid applied flexible acrylic waterproofing system over concrete. This work shall include the
More information1.02 DESCRIPTION A. This Section specifies furnishing and installing Cast in Place Detectable/Tactile Warning Surface tiles where indicated.
CAST IN PLACE DETECTABLE/TACTILE WARNING SURFACE TILE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions and Division 1 Specifications
More informationBlack epoxy paste adhesive system
Advanced Materials Araldite 2031 Structural Adhesives Araldite 2031 Black epoxy paste adhesive system Key properties Thixotropic non slumping Toughened adhesive, resilient bond Suitable for metal and composite
More information3 Scotch-Weld TM. Structural Adhesive Films AF 6 AF 10 AF 13. Technical Data July, 2001
3 Scotch-Weld TM Technical Data July, 2001 Introduction 3M Scotch-Weld AF 6, AF 10, AF 13 are unsupported, thermosetting adhesives in film form developed for the structural bonding of metals. These products
More informationSIGMACOVER 280. PRODUCT DATA SHEET December 10, 2014 (Revision of March 1, 2014) DESCRIPTION
DESCRIPTION Universal epoxy anticorrosive primer, based upon pure epoxy technology PRINCIPAL CHARACTERISTICS Universal epoxy primer system suitable for Ballast Tanks, Decks, Topside, Superstructure, Hull
More informationScotch-Weld. Low-Odor Acrylic Adhesives DP810 DP810 NS. Technical Data June, 2004
3 Scotch-Weld TM Technical Data June, 2004 Product Description 3M Scotch-Weld Low-Odor Acrylic Adhesive DP810 and DP810 NS are twopart, 1:1 mix ratio, toughened structural adhesives with less odor than
More informationSecondary Containment Comparison ATI Ultra COAT vs HDPE
When choosing a secondary containment system it must be chosen based on its ability to withstand long term contact with the natural elements (weather), whatever the tanks hold (unrefined oil, fuels, acids,
More informationSECTION 03 35 43. Formatted Specification for the ULTRAFLOR DIAMATIC Topical Polished Concrete System DRAFT
SECTION 03 35 43 Formatted Specification for the ULTRAFLOR DIAMATIC Topical Polished Concrete System PART I GENERAL 1.01 SUMMARY A. This is the recommended specification for ULTRAFLOR DIAMATIC Topical
More informationENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES
ENGINEERING SPECIFICATION PULTRUDED DYNARAIL FIBERGLASS LADDER & LADDER CAGES PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 06610 FIBERGLASS REINFORCED PLASTICS (FRP) FABRICATIONS PULTRUDED SQUARE TUBE LADDER
More informationAraldite AV 170. Advanced Materials. One component epoxy adhesive. Structural Adhesives. Key properties. Description. Product data.
Advanced Materials Araldite AV 170 Structural Adhesives Araldite AV 170 One component epoxy adhesive Key properties Cures at 140-180 C Heat resistant to 120 C Very good peel strength Good chemical resistance
More informationELASTOCEM. Technical features. Applications. Two-component flexible, waterproofing and protective cementitious grout.
Two-component flexible, waterproofing and protective cementitious grout. 1504-2 PI-MC-IR Technical features Two-component grout, based on cements, selected aggregates, special additives and synthetic polymers
More informationSample Specification Guideline for Installing a Polished Overlay Using Rapid Set TRU Self-Leveling SECTION 03 35 53 POLISHED CONCRETE TOPPING
Sample Specification Guideline for Installing a Polished Overlay Using Rapid Set TRU Self-Leveling SECTION 03 35 53 POLISHED CONCRETE TOPPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general
More informationSECTION 15125 HIGH DENSITY POLYETHYLENE (HDPE) PIPE AND FITTINGS FOR WATER DISTRIBUTION AND TRANSMISSION
SECTION 15125 HIGH DENSITY POLYETHYLENE (HDPE) PIPE AND FITTINGS FOR WATER DISTRIBUTION AND TRANSMISSION PART 1 GENERAL.01 SECTION INCLUDES Furnishing and installing 4 inch through 16 inch high density
More informationAC Tech Project Survey
AC Tech Project Survey PROJECT NAME: DATE: PROJECT SIZE: EST. START DATE: I. Overview Successful projects depend on accurate and detailed information. The AC Tech Approved Applicator must obtain and record
More informationSeamless Waterproofing. Systems
Seamless Waterproofing Systems Pitched/Corrugated Roofs Liquid Rubber Instant Set is the ideal solution for pitched roof waterproofing providing a seamless fully bonded finish. RapidRoof is suited to smaller
More informationExample Specification for Concrete using Current Building Code Requirements
Example Specification for Concrete using Current Building Code Requirements DISCLAIMER: This specification is an example that accompanies a seminar titled The P2P Initiative: Performance-based Specs for
More information3.8 HSP (High Solids Polyurethane)
Description is a single-stage topcoat designed for commercial and automotive refinishing. This product provides Superior UV durability as well as commercial grade chemical resistance. 3.8 HSP has excellent
More informationDocument Library TS Data Sheet 08609. 3M Windo-Weld Super Fast Urethane. Data Sheet. Public
Document Library TS Data Sheet 08609 Public Rev:3 Effective: 09/14/2007 Status: Active 3M Windo-Weld Super Fast Urethane Data Sheet 3M Part No.(s) 3M Part Descriptor(s) 08609 3M Windo-Weld Super Fast Urethane
More informationRTV162. Electronic Grade Silicone Adhesive Sealant
RTV162 Product Description Electronic Grade Silicone Adhesive Sealant RTV162 adhesive sealant from GE Silicones is one-component, readyto-use electronic grade silicone sealant. It cures to a tough, resilient
More informationNAPCA BULLETIN 18-99 APPLICATION PROCEDURES FOR CONCRETE WEIGHT COATING APPLIED BY THE COMPRESSION METHOD TO STEEL PIPE
NAPCA BULLETIN 18-99 APPLICATION PROCEDURES FOR CONCRETE WEIGHT COATING APPLIED BY THE COMPRESSION METHOD TO STEEL PIPE GENERAL a. These specifications may be used in whole or in part by any party without
More informationTIGER Drylac U.S.A., Inc. 3855 Swenson Avenue St Charles, IL T 800 243 8148 F 877 926 8148 office.us@tiger-coatings.us www.tiger-coatings.
Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Epoxy zinc-rich powder coating primer. Part of a two-coat TIGER Shield system. Designed to impart superior corrosion protection to steel
More informationMATERIAL SAFETY DATA SHEET Utrecht Gesso Painting Grounds. Section 2 Hazard Identification (composition / information on ingredients)
Page 1 of 6 MATERIAL SAFETY DATA SHEET Utrecht Gesso Painting Grounds MSDS 908.4 Date: April 27, 2014 Information: 800-223-9132 or: 609-409-8001 Section 1 Company and Product Identification Utrecht Art
More informationSee photo below showing this product being applied to a badly corroded floor.
SPECIALTY COATINGS, INC 805 Lehigh Ave. Union, NJ 07083 TEL 888-755-7361 FAX 888-755-6231 www.armorpoxy.com info@armorpoxy.com FLOOR REPAIR, LEVELING & PREP BULLETIN This bulletin has been prepared by
More informationImron 1.2 HG High Gloss Waterborne Polyurethane (WG Quality)
Imron 1.2 HG High Gloss Waterborne Polyurethane (WG Quality) GENERAL DESCRIPTION An isocyanate-free, high gloss, single component, VOC conforming (1.2 lbs/gal), zero HAPs coating based on unique Axalta
More information3 Scotch-Weld TM. Urethane Adhesives 3532 B/A 3535 B/A 3549 B/A. Technical Data March, 2002
3 Scotch-Weld TM Technical Data March, 2002 Product Description 3M TM Scotch-Weld TM 3532 B/A, 3535 B/A and 3549 B/A are two-component, polyurethane adhesives which cure at room temperature or with heat
More informationTwo component epoxy paste adhesive
Advanced Materials Araldite 2015 Structural Adhesives TECHNICAL DATA SHEET Araldite 2015 Two component epoxy paste adhesive Key properties Toughened paste Ideal for bonding GRP, SMC and dissimilar substrates
More informationYou have just purchased the most portable and economical spray chrome system in the world!
You have just purchased the most portable and economical spray chrome system in the world! The Chrome FX Gun comes attached directly to the pots making it extremely mobile and capable of performing on
More informationHYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS
HYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS Shiwei William Guan, Ph.D. Vice President, R&D and International Business Madison Chemical Industries Inc. 490
More information