Configuring Your Voice Gateway Using the setup Command
|
|
|
- Marsha Fisher
- 7 years ago
- Views:
Transcription
1 CHAPTER 2 Configuring Your Voice Gateway Using the setup Command This chapter describes how to use the setup command to configure your voice gateway. The setup command prompts you to enter information needed to start a voice gateway functioning quickly. The facility steps you through a basic configuration, including LAN interfaces. About Configuring Your Voice Gateway, page 2-1 Preparing to Configure Your Cisco Voice Gateway, page 2-1 Using the setup Command, page 2-2 Completing the Configuration, page 2-5 About Configuring Your Voice Gateway The Cisco VG202, Cisco VG202XM, Cisco VG204, and Cisco VG204XM voice gateways ship with a default configuration. During the first boot up, the voice gateways do not enter setup mode and are configured through auto-configuration. If you prefer to configure the voice gateway manually or if you wish to configure a module or interface that is not included in the setup command, proceed to Chapter 3, Configuring Your Voice Gateway Using the CLI, for step-by-step instructions. If you prefer to configure the voice gateway using AutoInstall, see Using AutoInstall to Remotely Configure Cisco Networking Devices. Preparing to Configure Your Cisco Voice Gateway Procedure Step 1 Step 2 Step 3 Set up the hardware as described in the Cisco VG202, Cisco VG202XM, Cisco VG204, and Cisco VG204XM Voice Gateways Hardware Installation Guide. Configure your PC terminal emulation program for 9600 baud, 8 data bits, no parity, and 1 stop bit. Determine which network protocols you support. 2-1
2 Using the setup Command Chapter 2 Step 4 Determine the addressing plan for each network protocol. Using the setup Command The setup command is displayed in your PC terminal emulation program window. Note If you make a mistake while using the setup command, you can exit and run the command again. Press Ctrl-C, and enter setup at the enable mode prompt (VG#). Procedure Step 1 Plug in the external power supply. The system begins to display messages in your terminal emulation program window. Caution The voice gateway does not enter setup mode during the initial configuration. During initial configuration, the voice gateway boots up in auto-configuration. You can only use the setup command to configure the voice gateway manually after the initial configuration. Using the setup command during the initial configuration erases the default configuration and must be avoided. Caution Do not press any keys on the keyboard until the messages stop. The system interprets any keys pressed during this time as the first command typed when the messages stop, which might cause the voice gateway to power off and start over. It takes a few minutes for the messages to stop. The messages look similar to the following example. System configuration has been modified. Save? [yes/no]: n Proceed with reload? [confirm] *Apr 21 14:23:38.051: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command. System Bootstrap, Version 12.4( :092610) [anyname-vg.v124_19_9_2_pia ios.sync 102], DEVELOPMENT SOFTWARE Copyright (c) by cisco Systems, Inc. VG202 platform with Kbytes of main memory Upgrade ROMMON initialized program load complete, entry point: 0x , size: 0x1437d40 Self decompressing the image: ########################################################################################## ########################################################################################## ################################# [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec and subparagraph 2-2
3 Chapter 2 Using the setup Command (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec cisco Systems, Inc. 170 West Tasman Drive San Jose, California Cisco IOS Software, VG20X Software (VG20X-ADVIPSERVICESK9-M), Version 12.4(ORBITTY_APRIL18_POST_SYNC_BUILD ) UBUILDIT Image, CISCO DEVELOPMENT TEST VERSION Copyright (c) by Cisco Systems, Inc. Compiled Fri 18-Apr-08 02:30 by geopasaaniha This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: If you require further assistance please contact us by sending to export@cisco.com. Cisco VG202 (MPC8300) processor (revision 0x100) with 98304K/32768K bytes of memory. Processor board ID FOC11334C2B MPC8300 CPU Rev: Part Number 0x8062, Revision ID 0x11 2 FastEthernet interfaces 2 Voice FXS interfaces 256K bytes of non-volatile configuration memory K bytes of ATA CompactFlash (Read/Write) --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: y At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Step 2 Step 3 When the following message appears, enter yes to begin the initial configuration dialog: Would you like to enter the initial configuration dialog? [yes/no]: When the following message appears, press Return to see the current interface summary: First, would you like to see the current interface summary? [yes]: Any interface listed with OK? value NO does not have a valid configuration Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned NO unset up up FastEthernet0/1 unassigned NO unset up down Step 4 Enter a hostname for the voice gateway: Configuring global parameters: 2-3
4 Using the setup Command Chapter 2 Enter hostname [VG]: VG204 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Step 5 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration: The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: cisco Step 6 Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration: The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: cisco % Please choose a password that is different from the enable secret Enter enable password: cisco Step 7 Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the voice gateway through ports other than the console port: The virtual terminal password is used to protect access to the VG over a network interface. Enter virtual terminal password: cisco Configure SNMP Network Management? [yes]: n Configure IP? [yes]: Configure RIP routing? [yes]: n Configure bridging? [no]: Respond to the following prompts as appropriate for your network: Do you want to configure FastEthernet0/0 interface? [yes]: Use the 100 Base-TX (RJ-45) connector? [yes]: Operate in full-duplex mode? [no]: Configure IP on this interface? [yes]: IP address for this interface: Subnet mask for this interface [ ] : Class A network is , 24 subnet bits; mask is /24 Do you want to configure FastEthernet0/1 interface? [yes]: n Would you like to go through AutoSecure configuration? [yes]: n AutoSecure dialog can be started later using "auto secure" CLI The following configuration command script was created: hostname VG-202 enable secret 5 $1$Y0VQ$D8qM6vS3qId.BP3w.GjlE. enable password cisco line vty 0 4 password cisco no snmp-server ip routing no bridge 1 2-4
5 Chapter 2 Completing the Configuration interface FastEthernet0/0 media-type 100BaseX half-duplex ip address interface FastEthernet0/1 shutdown no ip address dialer-list 1 protocol ip permit end Completing the Configuration After you have entered all the prompted information for the setup command, the system displays the configuration. Procedure Step 1 Step 2 Step 3 The system asks if you want to save this configuration, with the following options: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. If you enter 0, the system does not save the configuration information that you entered, and you return to the voice gateway enable prompt (VG#). Enter setup to return to the system configuration dialog. If you enter 1, the system returns you to the setup command without saving the configuration. If you enter 2, the system saves the configuration and returns you to the user EXEC prompt (VG>). When the messages stop appearing on your screen, press Return to get the VG> prompt. The VG> prompt indicates that you are now at the CLI and you have just completed a basic voice gateway configuration. However, this is not a complete configuration. At this point you have two choices: Run the setup command again and create another configuration. Enter the following: VG> enable Password: password VG# setup Modify the existing configuration or configure additional features with the CLI as described in Chapter 3, Configuring Your Voice Gateway Using the CLI. 2-5
6 Completing the Configuration Chapter 2 2-6
Password Recovery Procedure for the Cisco 2900 Series Integrated Services Router
Password Recovery Procedure for the Cisco 2900 Series Integrated Services Router Document ID: 112033 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Step by
Password Recovery Procedure for the Cisco 806, 826, 827, 828, 831, 836, 837 and 881 Series Routers
Password Recovery Procedure for the Cisco 806, 826, 827, 828, 831, 836, 837 and 881 Series Routers Document ID: 12065 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions
Password Recovery Procedure for the Cisco 3600 and 3800 Series Routers
Password Recovery Procedure for the Cisco 3600 and 3800 Series Routers Document ID: 22189 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Step by Step Procedure
Password Recovery Procedure for the Cisco Catalyst 2948G L3, 4840G, and 4908G L3 Switch Routers
Password Recovery Procedure for the Cisco Catalyst 2948G L3, 4840G, and 4908G L3 Switch Routers Document ID: 12738 Contents Introduction Before You Begin Conventions Prerequisites Step by Step Procedure
Configuring the Switch with the CLI-Based Setup Program
APPENDIX D Configuring the Switch with the CLI-Based Setup Program This appendix provides a command-line interface (CLI)-based setup procedure for a standalone switch. For product overview information,
Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands.
Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands. Learn about Cisco IOS troubleshooting techniques. Understand upgrading
3.1 Connecting to a Router and Basic Configuration
3.1 Connecting to a Router and Basic Configuration Objective This lab will focus on the ability to connect a PC to a router in order to establish a console session and observe the user interface. A console
Configuring the Switch with the CLI Setup Program
APPENDIXC Configuring the Switch with the CLI Setup Program This appendix provides a command-line interface (CLI) setup procedure for a standalone switch. To set up the switch by using Express Setup, see
CT5760 Controller and Catalyst 3850 Switch Configuration Example
CT5760 Controller and Catalyst 3850 Switch Configuration Example Document ID: 116342 Contributed by Antoine KMEID and Serge Yasmine, Cisco TAC Engineers. Aug 13, 2013 Contents Introduction Prerequisites
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Objective This lab may introduce new CCNP lab equipment and certain IOS features. This introductory activity also describes how to
Lab 2 - Basic Router Configuration
CS326 Fall 2001 Room: PAI 5.48 Name: Lab 2 - Basic Router Configuration In this lab you will learn: the various configuration modes of Cisco 2621 routers how to set up IP addresses for such routers how
Lab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt
Lab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt Objective This lab will introduce to the student the CCNP lab equipment and certain IOS features that might be new. This introductory
Basic Configuration of the Cisco 12000 Series Internet Router
CHAPTER 2 Basic Configuration of the Cisco 12000 Series Internet Router This chapter describes how to boot and configure the Cisco 12000 Series Internet Router. It discusses the following subjects: Cisco
Lab 1.2.3 Review of Basic Router Configuration with RIP. Objective. Background / Preparation. General Configuration Tips
Lab 1.2.3 Review of Basic Router Configuration with RIP Objective Cable and configure workstations and routers Setup IP addressing scheme using Class B networks Configure Routing Information Protocol (RIP)
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the
Angelos Stavrou. OF COURSE there is no Magic so lets see show things work in practice...
Cisco Inter-network Operating System (IOS) A short guide for the NetAdmin Angelos Stavrou Let's start out at the very beginning with the question: "What is a Command?" The most important thing to understand
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP
The Purpose and Use of the Configuration Register on All Cisco Routers
The Purpose and Use of the Configuration Register on All Cisco Routers Document ID: 50421 Contents Introduction Prerequisites Requirements Components Used Conventions The Purpose of the Configuration Register
Xmodem Console Download Procedure Using ROMmon
Xmodem Console Download Procedure Using ROMmon Document ID: 15085 Contents Introduction Prerequisites Requirements Components Used Conventions Overview Usage Examples Xmodem Procedure for Downloading a
Objectives. Router as a Computer. Router components and their functions. Router components and their functions
2007 Cisco Systems, Inc. All rights reserved. Cisco Public Objectives Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 Identify a router as a computer with an OS and
Upgrade de IOS de Router Cisco 1005 a c1005-bny-mz.112-20.bin
Upgrade de IOS de Router Cisco 1005 a c1005-bny-mz.112-20.bin Diagrama de conexionado para el upgrade: Conexión a la Consola del Router 8 NONE -1 // 9600 bps Conexión a la Ethernet del Router IP_Router=192.168.0.201/24
Digitally Signed Cisco Software
Digitally Signed Cisco Software Last Updated: January 16, 2013 The Digitally Signed Cisco Software feature describes how to identify digitally signed Cisco software, gather software authentication information
Procedure: You can find the problem sheet on Drive D: of the lab PCs. Part 1: Router & Switch
University of Jordan Faculty of Engineering & Technology Computer Engineering Department Computer Networks Laboratory 907528 Lab. 2 Network Devices & Packet Tracer Objectives 1. To become familiar with
Basic Software Configuration Using the Cisco IOS Command-Line Interface
Basic Software Configuration Using the Cisco IOS Command-Line Interface This document describes how to use the Cisco IOS command-line interface (CLI) to perform a basic software configuration for your
ROM Monitor. Entering the ROM Monitor APPENDIX
APPENDIX B This appendix describes the Cisco router ROM monitor (also called the bootstrap program). The ROM monitor firmware runs when the router is powered up or reset. The firmware helps to initialize
Lab 7.2.9 Load Balancing Across Multiple Paths
Lab 7.2.9 Load Balancing Across Multiple Paths Objective Configure Load balance across multiple paths. Observe the load balancing process. Background/Preparation Cable a network similar to the one in the
Cisco - Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW)
Page 1 of 20 Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW) Document ID: 50036 Contents Introduction Prerequisites Requirements Components Used Network Diagram The Role of Switched
Lab 5.3.9b Managing Router Configuration Files Using TFTP
Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.
- Advanced IOS Functions -
1 The Configuration Register - Advanced IOS Functions - The configuration register (config-register) is a hexadecimal value that controls various aspects of how a router boots, including: Baud Rate Boot
Cisco 1700 Router Overview
CHAPTER 1 Cisco 1700 Router Overview This chapter introduces the Cisco 1700 router, also referred to in this guide as the router, and covers the following topics: Key Features Rear-Panel Ports and LEDs
Applicazioni Telematiche
Angelo Coiro Laboratorio Applicazioni Telematiche L emulatore Packet Tracer Packet Tracer Cisco Packet Tracer is an academic software that allows to emulate Cisco devices Packet Tracer can be used for
Configuring Voice over IP
CHAPTER 4 This chapter explains how to configure voice interfaces and ports, which convert telephone voice signals for transmission over an IP network. This chapter presents the following major topics:
Cisco ISE Command-Line Interface
This chapter provides information on the Cisco Identity Services Engine (Cisco ISE) command-line interface (CLI) that you can use to configure and maintain Cisco ISE. Cisco ISE Administration and Configuration
Lab 6.2.3 Managing the MAC Address Table
Lab 6.2.3 Managing the MAC Address Table Objective Create a basic switch configuration. Manage the switch MAC table. Background/Preparation Cable a network similar to the one in the diagram. The configuration
Connecting to the Firewall Services Module and Managing the Configuration
CHAPTER 3 Connecting to the Firewall Services Module and This chapter describes how to access the command-line interface and work with the configuration. This chapter includes the following sections: Connecting
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI Device Host Name Interface IP Address Subnet Mask R1 R1 Serial 0/0/0 (DCE) 172.17.0.1 255.255.0.0 FastEthernet 0/0 172.16.0.1 255.255.0.0
Lab 3 Routing Information Protocol (RIPv1) on a Cisco Router Network
Lab 3 Routing Information Protocol (RIPv1) on a Cisco Router Network CMPE 150 Fall 2005 Introduction Today you are going to be thrown into using Cisco s Internetwork Operating System (IOS) to configure
Lab 3.1.2 Creating a Logical Network Diagram
Lab 3.1.2 Creating a Logical Network Diagram Objectives Use router and switch commands to obtain information about an existing network. Use Cisco Network Assistant to obtain information about an existing
Lab 4.2.4 Advanced Telnet Operations
Lab 4.2.4 Advanced Telnet Operations Objective Use the telnet command to remotely access other routers. Verify that the application layer between the source and the destination is working properly. Suspend
CCNA Exploration 4.0.5.0 Routing Protocols and Concepts Student Lab Manual
4.0.5.0 Routing Protocols and Concepts Student Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution
Cisco Configuration Professional Quick Start Guide
Cisco Configuration Professional Quick Start Guide April 29, 2011 This document explains how to start using Cisco Configuration Professional Express (Cisco CP Express) and Cisco Configuration Professional
Router Lab Reference Guide
Router Lab Reference Guide 1 PURPOSE AND GOALS The routing lab allows testing different IP-related protocols and solutions in a close to live environment. You can learn how to configure Cisco routers and
Configuring the Content Routing Software
CHAPTER 2 This chapter describes the basic steps for configuring the Content Router software. Performing a Basic Startup Configuration After you physically install the Content Router hardware, configure
Remote Annex. Quick Start for Windows. Read before installing and using Remote Annex Software Release 4.2
Remote Annex Quick Start for Windows Read before installing and using Remote Annex Software Release 4.2 These installation notes contain information specific to this release. This information is not available
Lab 5.3.7 Configuring DHCP with SDM and the Cisco IOS CLI
Lab 5.3.7 Configuring DHCP with SDM and the Cisco IOS CLI Device Host Name Interface IP Address Subnet Mask R1 Customer Serial 0/0/1 (DTE) 209.165.200.225 255.255.255.224 Fast Ethernet 0/0 192.168.1.1
Lab 5.3.8 Configuring PAT with SDM and Static NAT using Cisco IOS Commands
Lab 5.3.8 Configuring PAT with SDM and Static NAT using Cisco IOS Commands Device Host Name Interface IP Address Subnet Mask R1 CustomerRouter Serial 0/0/0 (DTE) 209.165.200.225 255.255.255.224 Fast Ethernet
Configuring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
Lab: Basic Router Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Def. Gateway R1 Fa0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 192.168.2.1 255.255.255.0 N/A R2 Fa0/0 192.168.3.1 255.255.255.0 N/A
Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP
Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP Host Device Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Analyze the Cisco IOS image and router
Backing Up and Restoring Data
Backing Up and Restoring Data Cisco Unity Express backup and restore functions use an FTP server to store and retrieve data. The backup function copies the files from the Cisco Unity Express application
Introduction to Routing and Packet Forwarding. Routing Protocols and Concepts Chapter 1
Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 1 1 Objectives Identify a router as a computer with an OS and hardware designed for the routing process. Demonstrate
These documents explains how to configure and maintain your Cisco router.
Preface This preface describes the objectives, audience, organization, and conventions of the software configuration documentation for your router. It contains the following sections: Objectives, page
USB Disable for Cisco ISRs Feature Module
USB Disable for Cisco ISRs Feature Module First Published: March 28, 2011 Part Number: This guide describes the USB Disable feature in the following major sections: Feature Introduction, page 1 Restrictions,
Lab 2.3.2 Configuring OSPF with Loopback Addresses
Lab 2.3.2 Configuring OSPF with Loopback Addresses Objective Configure routers with a Class C IP addressing scheme. Observe the election process for designated routers (DR) and backup designated routers
Lab 5.5.4 Configuring the Cisco 2960 Switch
Lab 5.5.4 Configuring the Cisco 2960 Switch Device Host Name Interface IP Address Subnet Mask Default Gateway Switch Port S1 CustomerSwitch VLAN 1 192.168.1.5 255.255.255.0 192.168.1.1 N/A R1 CustomerRouter
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1
Lab 8.3.3b Configuring a Remote Router Using SSH
Lab 8.3.3b Configuring a Remote Router Using SSH Objectives Use SDM to configure a router to accept SSH connections. Configure SSH client software on a PC. Establish a connection to a Cisco ISR using SSH
SecureLinx Spider Duo Quick Start Guide
SecureLinx Spider Duo Quick Start Guide SecureLinx Spider Duo Quick Start Guide SecureLinx Spider Duo QUICK START GUIDE CONTENTS Overview... 2 What s In The Box... 3 Installation and Network Settings...
Lab 8.4.3a Managing Cisco IOS Images with TFTP
Lab 8.4.3a Managing Cisco IOS Images with TFTP Host Device Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Analyze the Cisco IOS image and router flash memory.
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI
Lab 5.3.5 Configuring Basic Router Settings with the Cisco IOS CLI Device Host Name Interface IP address Subnet mask R1 R1 Serial 0/0/0 (DCE) 172.17.0.1 255.255.0.0 FastEthernet 0/0 172.16.0.1 255.255.0.0
How To Set Up A Netvanta For A Pc Or Ipad (Netvanta) With A Network Card (Netvina) With An Ipa (Net Vanta) And A Ppl (Netvi) (Netva)
VPN WAN LAN PWR STAT TD RD TD RD TD RD VPN WAN LAN PWR STAT TD RD TD RD TD RD NetVanta 3200 NetVanta 3200 NetVanta Series (with T1/FT1 or T1/FT1 + DSX-1 Network Interface Module) Quick Configuration Guide
Lab - Using IOS CLI with Switch MAC Address Tables
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.1.1 255.255.255.0 N/A S1 VLAN 1 192.168.1.11 255.255.255.0 192.168.1.1 S2 VLAN 1 192.168.1.12
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following
Maintaining the Content Server
CHAPTER 7 This chapter includes the following Content Server maintenance procedures: Backing Up the Content Server, page 7-1 Restoring Files, page 7-3 Upgrading the Content Server, page 7-5 Shutting Down
Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.
Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A
SNMP-1 Configuration Guide
SNMP-1 Configuration Guide You must configure the Net Logic Card before it can operate properly. You have two methods to configure the Net Logic Card: Using telnet or terminal. Using Telnet 1. Make sure
Password Recovery Procedure for the Cisco Catalyst Fixed Configuration Layer 2 and Layer 3 Switches
Password Recovery Procedure for the Cisco Catalyst Fixed Configuration Layer 2 and Layer 3 Switches Document ID: 12040 Contents Introduction Before You Begin Conventions Prerequisites Step by Step Procedure
Connecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
http://computernetworkingnotes.com/ccna-study-guide/cisco-ios-naming-convention-explainedwith-examples.html
IOS is the most critical part of any cisco device. We should always keep a backup copy of IOS to deal with any unwanted situation. In this article I will explain the backup and restore process of IOS in
Configuring Switch Ports and VLAN Interfaces for the Cisco ASA 5505 Adaptive Security Appliance
CHAPTER 5 Configuring Switch Ports and VLAN Interfaces for the Cisco ASA 5505 Adaptive Security Appliance This chapter describes how to configure the switch ports and VLAN interfaces of the ASA 5505 adaptive
Recover a Router from Corrupted or Missing Software Image
Cisco SMB Support Assistant Recover a Router from Corrupted or Missing Software Image Cisco Profile Contacts & Feedback Help Home > Work With My Routers > Cisco Routers > Recover a Router from Corrupted
ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4
ACU-1000 Manual Addendum Replacement of CPM-2 with CPM-4 1 PURPOSE:... 1 2 CPM-4/CPM-2 COMPATIBILITY... 2 2.1 NETWORK CABLES... 2 2.2 FACTORY DEFAULT SETTINGS... 2 2.3 CHANGING THE RS-232 SERIAL PORT BAUD
Cisco Router Configuration Tutorial
Cisco Router Configuration Tutorial Cisco Inter-network Operating System: Cisco IOS Modes of Operation The Cisco IOS software provides access to several different command modes. Each command mode provides
Lab 4.1.2 Characterizing Network Applications
Lab 4.1.2 Characterizing Network Applications Objective Device Designation Device Name Address Subnet Mask Discovery Server Business Services 172.17.1.1 255.255.0.0 R1 FC-CPE-1 Fa0/1 172.17.0.1 Fa0/0 10.0.0.1
Loading IOS Image with Xmodem when TFTP is unavailable
Loading IOS Image with Xmodem when TFTP is unavailable Router#show version Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-D-M), Version 12.0(7), RELEASE SOFTWARE (fc1) Copyright
Quick Start Guide. Cisco Small Business. 200E Series Advanced Smart Switches
Quick Start Guide Cisco Small Business 200E Series Advanced Smart Switches Welcome Thank you for choosing the Cisco 200E series Advanced Smart Switch, a Cisco Small Business network communications device.
Starting a Management Session
Management Software AT-S63 Starting a Management Session AT-S63 Version 2.2.0 for the AT-9400 Layer 2+ Switches AT-S63 Version 3.0.0 for the AT-9400 Basic Layer 3 Switches 613-000817 Rev. A Copyright 2007
Lab 3.10.2 Use Network Inspector to Observe STP Behavior
Lab 3.10.2 Use Network Inspector to Observe STP Behavior Objective The purpose of this lab is to observe STP behavior with the Network Inspector switch trace feature. Scenario A new switched network has
Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others
Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java
Comware versus Cisco IOS Command Guide
Technical Marketing Engineering Routing and Switching Technology Routing and Switching Comware versus Cisco IOS Command Guide Technical Marketing Brief Revision v5 March 23, 2009 http://www.3com.com 3Com
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL w w w. c d v g r o u p. c o m CA-ETHR-A: TCP/IP Module Installation Manual Page Table of Contents Introduction...5 Hardware Components... 6 Technical Specifications...
BRI to PRI Connection Using Data Over Voice
BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot
Backup and Recovery Procedures
CHAPTER 10 This chapter provides Content Distribution Manager database backup and ACNS software recovery procedures. This chapter contains the following sections: Performing Backup and Restore Operations
USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
Router and Routing Basics
Router and Routing Basics Malin Bornhager Halmstad University Session Number 2002, Svenska-CNAP Halmstad University 1 Routing Protocols and Concepts CCNA2 Routing and packet forwarding Static routing Dynamic
50-Port 10/100/1000Mbps with 4 Shared SFP. Managed Gigabit Switch WGSW-50040. Quick Installation Guide
50-Port 10/100/1000Mbps with 4 Shared SFP Managed Gigabit Switch WGSW-50040 Quick Installation Guide Table of Contents 1. Package Content... 3 2. Switch Management... 4 3. Requirements... 5 4. Terminal
During this lab time you will configure the routing protocol OSPF with IPv4 addresses.
Lab 2: OSPF During this lab time you will configure the routing protocol OSPF with IPv4 addresses. It is your responsibility to create an appropriate IPv4 subnet plan and address plan. To ensure a timely
Using the Cisco IOS Command Line Interface
CHAPTER 3 Using the Cisco IOS Line Interface 3.1 Using the CLI Cisco IOS software provides a command line interface (CLI) that allows you to configure and manage the Cisco 6200 advanced digital subscriber
Connecting and Setting Up Your Laptop Computer
CHAPTER 3 Connecting and Setting Up Your Laptop Computer This chapter explains how to connect your laptop to the Cisco Unified MeetingPlace system and how to set up your laptop so that you can use HyperTerminal.
Lab 4.5.4 Diagramming External Traffic Flows
Lab 4.5.4 Diagramming External Traffic Flows Device Designation Device Name Address Subnet Mask Discovery Server Business Services 172.17.1.1 255.255.0.0 R1 R2 R3 FC-CPE-1 FC-CPE-2 ISP Fa0/1 172.17.0.1
Configuring the PIX Firewall with PDM
Configuring the PIX Firewall with PDM Objectives In this lab exercise you will complete the following tasks: Install PDM Configure inside to outside access through your PIX Firewall using PDM Configure
Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access
Table of Contents Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Configure...2
Management Software. User s Guide AT-S84. For the AT-9000/24 Layer 2 Gigabit Ethernet Switch. Version 1.1. 613-000368 Rev. B
Management Software AT-S84 User s Guide For the AT-9000/24 Layer 2 Gigabit Ethernet Switch Version 1.1 613-000368 Rev. B Copyright 2006 Allied Telesyn, Inc. All rights reserved. No part of this publication
- The PIX OS Command-Line Interface -
1 PIX OS Versions - The PIX OS Command-Line Interface - The operating system for Cisco PIX/ASA firewalls is known as the PIX OS. Because the PIX product line was acquired and not originally developed by
Encrypted Preshared Key
Encrypted Preshared Key The Encrypted Preshared Key feature allows you to securely store plain text passwords in type 6 (encrypted) format in NVRAM. Feature History for Encrypted Preshared Key Release
HOW TO CONFIGURE CISCO FIREWALL PART I
HOW TO CONFIGURE CISCO FIREWALL PART I Cisco Abstract: Please find below a step by step process to configure the PIX Firewall from scratch. A simple scenario is given here where you have a corporate network
Command Line Interface User s Guide
Management Software AT-S85 and AT-S97 Command Line Interface User s Guide AT-MCF2000 Media Converter Series Version 1.3.0 613-000789 Rev. A Copyright 2007 Allied Telesis, Inc. All rights reserved. No part
Remote PC Guide for Standalone PC Implementation
Remote PC Guide for Standalone PC Implementation Updated: 2007-01-22 The guide covers features available in NETLAB+ version 3.6.1 and later. IMPORTANT Standalone PC implementation is no longer recommended.
Dell OpenManage Mobile Version 1.4 User s Guide (Android)
Dell OpenManage Mobile Version 1.4 User s Guide (Android) Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION