INSTALLATION INSTRUCTIONS FOR PART APPLICATIONS

Transcription

1 INSTLLTION INSTRUTIONS FOR PRT KIT FETURES PPLITIONS ILL ELORO SEVILLE EVILLE EVILLE ONOURS (ONSOLE SHIFT) IN Mount Radio Provision with Pocket ISO Mount Radio Provision with Pocket KIT OMPONENTS ) Radio Housing ) Radio Housing rackets ) ISO rackets ) ISO Trim Plate E) Spacer F) (4) Phillips Screws 98-04S F E TOOLS REQUIRE: Small Flat lade Screwdriver Panel Removal Tool Phillips Screwdriver Socket Wrench OPYRIGHT METR ELETRONIS ORPORTION

2 TLE OF ONTENTS ash isassembly - adillac Eldorado adillac Seville adillac Seville adillac eville adillac eville oncours (onsole Shift) Kit ssembly - adillac Eldorado adillac Seville adillac Seville adillac eville adillac eville oncours (onsole Shift) IN Mount Radio Provision ISO Mount Radio Provision Final ssembly *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto or call for more information and take steps toward a better tomorrow.

3 SH ISSSEMLY ILL ELORO ILL SEVILLE isconnect the negative battery terminal to prevent an accidental short circuit. Remove -clip on forward facing side of shift knob and pull and remove knob. (Figure ) Remove () 9/ screws on each side of the ashtray assembly and () in the middle underneath ashtray insert. (Figure ) Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel. (Figure ) Remove (4) 9/ screws () from the top (Figure ) and () from the bottom to remove radio. (Figure E) Remove the (6) retaining nuts securing the radio and climate control to the factory bracket assembly and slide the climate control outward. (Figure F) F Remove Retaining Nuts Per Side E

4 SH ISSSEMLY ILL SEVILLE ILL EVILLE ONOURS (ONSOLE SHIFT) isconnect the negative battery terminal to prevent an accidental short circuit. Remove () 9/ screws on each side of the ashtray assembly and () in the middle underneath ashtray insert. (Figure ) Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel. (Figure ) Remove () 9/ screws () from the top (Figure ) and () from the bottom to remove radio. (Figure ) Remove the (6) retaining nuts securing the radio and climate control to the factory bracket assembly and slide the climate control outward. (Figure E) E Remove Retaining Nuts Per Side

5 SH ISSSEMLY ILL EVILLE isconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove panel surrounding climate controls and radio. (Figure ) epress clips on both sides of radio and pull out to remove. (Figure )

6 KIT SSEMLY ILL ELORO ILL SEVILLE Remove all tabs except the ones marked from the radio housing. (Figure ) Slide the radio housing bracket onto the until side clips engage. (Figure ) Slide the climate control assembly into the bracket / housing assembly and attach with the factory hardware. (Figure ) 4

7 KIT SSEMLY ILL SEVILLE ILL EVILLE ONOURS (ONSOLE SHIFT) NOTE: In order to IN mount in the eville you will need to use the provided spacer as described below. There is not enough depth to ISO mount or IN mount without the spacer. Remove all tabs except the ones marked from the radio housing. (Figure ) Slide the radio housing bracket onto the until side clips engage. (Figure ) Slide the climate control assembly into the bracket / housing assembly and attach with the factory hardware. (Figure ) 4 When IN mounting slide the included spacer onto the IN cage that came with your aftermarket radio before inserting it into the housing. (Figure ) 5

8 KIT SSEMLY ILL EVILLE NOTE: In order to IN mount in the eville you will need to use the provided spacer as described below. There is not enough depth to ISO mount or IN mount without the spacer. Remove all tabs except the ones marked from the radio housing. (Figure ) When IN mounting slide the included spacer onto the IN cage that came with your aftermarket radio before inserting it into the housing. (Figure ) When installing the housing into the sub dash, use the supplied (4) phillips screws and mount in the locations shown (Figure ) 6

9 KIT SSEMLY IN HE UNIT PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Slide the IN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) Slide the after-market head unit into the cage and secure. (Figure ) 7

10 KIT SSEMLY ISO IN HE UNIT PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. Mount the ISO brackets to the aftermarket radio with the screws supplied with the unit. (Figure ) Slide the after-market radio unit into the cage and secure. (Figure ) Snap the Trim plate into the Radio Housing. (Figure ) 8

11 FINL SSEMLY Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit FINL SSEMLY ) Strip wire ends back /" ) Twist ends together ) Solder ) Tape METR / EI WIRING OE V Ignition / cc... Red V att / Memory.. Yellow Ground lack* Power ntenna..... lue mp Turn-On lue / White mp Ground lack / White Illumination Orange immer Orange / White Right Front (+)..... Gray Right Front (-) Gray / lack Left Front (+) White Left Front (-) White / lack Right Rear (+) Violet Right Rear (-) Violet / lack Left Rear (+) Green Left Rear (-) Green / lack *NOTE: When lack a wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 9

12 INSTRUTIONS Rev OPYRIGHT METR ELETRONIS ORPORTION INST99-005