CONSTRUCTION GUIDE FOR MONO BAND PANDA 1 SSB/CW TRANSCEIVER
|
|
- Luke Booker
- 7 years ago
- Views:
Transcription
1 CONSTRUCTION GUIDE FOR MONO BAND PANDA 1 SSB/CW TRANSCEIVER SPECIFICATIONS VXO Coverage: MHz Power Consumption:50mA (receiving mode) Output Power:5W CONSTRUCTION L1 (Optional) 9 MHz trap for conditions where there is a radio broadcast signal near 9 MHz when Panda 1 is used for 40 meter band. L1: 0.1 wire, 16 turns on the can former, C L2, L3: Band-pass filter inductors wire, 22 turns on NXO-10 toroid core. The wire should spread evenly on the core. Do not overlap the wire. 1
2 T1,T2: Mixer transformer. Thread a pair of 0.1 wires through the miniature binocular core, 6 turns. Then thread another piece of 0.1 wire from the other direction, 6 turns. See photo (For a clear instruction, a bigger core and colored thicker wires are used). The start of one wire (in the photo case, yellow) is connected with the end of the other wire (in the photo case, purple) to act as a tap. Solder the mixer transformers to the board, and fix them with a tape. The temperature of the solder will remove the lead enamel. T3:Broad-band ferrite transformer, 8 bifilar turns, 0.31 wire, on the broadband core. The wires are twisted. See photo. Pay attention to the phase. 3 and 2 are connected as the tap. 2
3 T4:IF transformer. 0.1 wire on the miniature binocular core, primary (crystal side) 5 turns, secondary 10 turns. It can be solder directly on the board, or fix it to a former, and then fix the assembly to the board. The temperature of the solder will remove the lead enamel. T5:Use the can former. 0.1 wire, primary (the 3-pin side) 16 turns, counter clockwise, the turns spread in 4 slots. Secondary (2-pin side), 4 turns in the bottom slot, counter clockwise. Wind the 2-pin side first. Pay attention to the start. See the left illustration (Bottom view). The photo on the right shows 4 turns in the slots. T6:Primary (U3 side) 22 turns on NXO-10 core, 0.31 wire. Secondary 6 turns, spread on the middle portion of primary. Pay attention to the winding direction. 3
4 T7:Can former, 0.1 wire. Primary (3-pin side)18 turns, spread in 4 slots; secondary 4turns. Wind the secondary first. T8:Broad band transformer. 5 bifilar turns, 0.31 wire, on the binocular core formed by 2 sleeves. See photo. Pay attention to the phase. 3 and 2 are connected as the tap. T9: Broad-band ferrite transformer, 10 bifilar turns, 0.31 wire, on the broadband core. The wires are twisted. See photo. Pay attention to the phase. 3 and 2 are connected as the tap. L4:0.31 wire, 21 turns, on NXO-10 core. L5:Can former, 0.1 wire, 31 turns,spread in 5 slots. L6, L7:0.31 or 0.47 wire, 16 turns on NXO-10 core. RFC1:5 turns on the small bead or small toroid. RFC4: 0.31 wire, 3 turns on the small bead or the small toroid ring. RFC5: 0.47 wire, 3 turns on the small toroid ring. The 0.1 mm wire needs not removing the lead enamel. The temperature of the solder will remove the lead enamel mm wire needs removing the lead enamel with a knife and tin them before soldering the transformer to the PCB. Jump R45 with a short thick wire (e.g. a piece of cut component lead). PWR SW is for mounting a power switch. Jump the hol es with a thick wire. C73 is fixed on the back. Insert a piece of paper between the heat sink and the board to prevent short circuit. 4
5 VXO Module L1:Can former. 0.1 wire, 49turns,spread in 5 slots. T1:Primary 11turns, secondary 3 turn on the broad-band core. Pay attention to the connection( 漏极 stands for Drain of Q2, 电源 power, 地 GND, 输出 OUT). See photo. For better VXO output, use NXO-10 core for T1 instead of the broadband core. Primary 15 turns; secondary 3 turns. Connect an 82P ceramic disc in parallel with the primary so as to tune T1 to resonance. Or use a var cap of 60P and a 47P ceramic disc, and tune the var cap to peak T1. VXO module is mounted on the main board by means of the pins and sockets. L1 can be fixed on the back to lower the height. There should be enough clearance between the module and the main board to reduce the interference. Do not cut the leads of the var cap diode. Bend the leads and solder, so that there is a clearance between the diode and the PCB. 5
6 Definitions of Main Board Interfaces LO IN:LO input port, connected to the VXO output port via 2 pins SP:AF output port, Connected to the speaker VOL:Volume control, connected to the 10K pot MIC:Microphone port, connected to the microphone AUX:12 V port to supply power to VXO module MODE:Mode switch, connected Mode switch KEY:CW key, connected to the key PTT:Push to talk ANT:Antenna PWR SW:Power switch. Please jump the holes LED: RX indicator Definitions of VXO Module VR1:Tuning port, connected to 10K pot VXO OUT:LO output port 12V:Power port Connecting the interfaces Solder the interfaces with wires. Use a thin screen cable to connect MIC if necessary. MODE is connected as illustrated in the following figure. ANT is connect to the Q9 socket with short thick wires. 6
7 Adapting some components VR1, VR2, VC1-VC4 need some changes to fit the pads, see photo. The center hole of T5 should be bridged with solder with the lead hole on the right (See photo). Polar of C32 The polar of C32 is as following picture. 7
8 Alignment BFO Set the mode switch at SSB or CW. Connect a frequency counter to the emitter of Q3.Turnthe slug of L5, until the reading is aro und MHz. Check CW mode frequency. Disconnect RFC5 to disable Set the mode to CW. Short CW key, see if the reading is around In reality the 471 ceramic meets the requirement, and no adjustment is needed. Connect RFC 5. VXO Dot not connect the module to the main board. Supply a 12V to the power pin of the module. Connect a ohm resistor at VXO OUT. Connect a frequency counter to the output port. Set the 10K tuning pot to the lowest voltage end (pot center to the ground)adjust L1, until the reading is ,and turn the pot to the high voltage end, the reading should be around Disconnect the 47-ohm resistor. Plug the VXO module to the main board. 8
9 Receiving Do not connect the antenna. Use a digital meter to measure the voltage of pins 4 and 6 of U1. Adju st VR1 until voltage of pin 4 is around 1.19V, pin 6 around 0.65, or V4-V6 = 0.5V. Now AGC works at the best condition. Never short pins 2 and 3. Another simple way to adjust U1 is to wear earphones, adjust VR1, until you hear a relatively louder hiss sound. Adjust T5. Listen the carefully. Turn the slug, peak the weak hiss sound until until you hear a relatively louder hiss sound. Connect the antenna. Adjust VC1 and VC2 to the position as shown in the below picture. Trim VC1 and VC2 to peak the received signals. Receiving alignment is done. The core in the right picture has 22 turns. LED resistor is 4.7K. Increase R3 can reduce power drain. 9
10 Transmitting Connect 50ohm dummy load to the ANT (A 2W resistor works fine).use multi meter (250MA range) to measure the current. Press PTT, the reading should be around 100MA. R43 is the bias resistor of K works fine. Adjust VC4 to the position as shown in the photo on the right. If your winding is correct (check against the photo), T6 works. Set the mode to CW. Change to 1A range. Adjust T7, until the reading is maximum. 10
11 Data for 20 meter band: L3, L4 16 turns. C3, C5:47,C4: 3,C2, C6:20 L6 L7 11 turns. C74, C76:221,C75:471 T6 Prim 16,sec 4,C57:47 Adjust VC4 to the position as shown in the photo (Around 30P). T7 2-pin side 4 turns. 3-pin side,12turns. C63:47 L1(VXO) 39 turns. VXO coverage: MHz (or MH z) T1: Prim 12T, sec 3T, on NXO-10 core. Connect a 68P ceramic disc in parallel with the primary. See photo. Note: For 20m, use a P ceramic for L5 so that PANDA works at USB. Now BFO works at around MHz. A var cap of 1/10P can also be used. Side tone If release the CW key there is a sustained sound can be heard from the loud speaker, then a 47 K resistor is need between the ground and collector of Q11. This resistor can be soldered at the place as shown in the following photo. 11
Youkits TJ2B 2016 SSB CW HF TRANSCEIVER OPERATION GUIDE
Youkits TJ2B 2016 SSB CW HF TRANSCEIVER OPERATION GUIDE TJ2B is a high-performance QRP portable multi-band SSB/CW transceiver, used with DDS as LO, offering wide frequency coverage and fine tuning rate.
More informationA CW QRP Transceiver for 20 m band. How it works I'll describe individually the three boards and the relative tuning devices.
A CW QRP Transceiver for 20 m band The little QRP presented in this article may be built in a gradual manner, in fact it is divided in two main modules (plus VFO), you may also complete only a single part
More informationModifying the Yaesu FT-847 External 22.625 MHz Reference Input
Modifying the Yaesu FT-847 External 22.625 MHz Reference Input David Smith VK3HZ Introduction This document describes the modification of an FT-847 to allow an external 22.625 MHz Reference oscillator
More informationCumbria Designs T-1. SSB/CW Filter kit (4.9152MHz) User Manual
Cumbria Designs T-1 SSB/CW Filter kit (4.9152MHz) User Manual CONTENTS 1 INTRODUCTION 2 2 CIRCUIT DESCRIPTION 2 3 ASSEMBLY 2 4 TESTING 4 The Steading Stainton PENRITH Cumbria CA11 0ES UK 1 Introduction
More informationAlpha 10 SERVICE MANUAL. Downloaded from www.cbradio.nl. MAX 10 Meter Amateur Transceiver AM/FM/CW/SSB 6 BAND PROGRAMMABLE MODEL AM-1000.
Alpha 10 MAX 10 Meter Amateur Transceiver MODEL AM-1000 AM/FM/CW/SSB 6 BAND PROGRAMMABLE SERVICE MANUAL Downloaded from www.cbradio.nl Cover Page LOUDER TALKBACK MOD Alpha 10 Max - Model AM-1000 4.7K Resistor
More informationHomebuilt HF Radios for Use Underground Paul R. Jorgenson KE7HR
Homebuilt HF Radios for Use Underground Paul R. Jorgenson KE7HR With the good success in using Amateur Band HF radio for underground communications, I started looking for cheaper alternatives to the $500+
More informationDL-QRP-AG Lambda/2 no Counterpoise: Fuchs Antenna matching unit
DL-QRP-AG Lambda/2 no Counterpoise: Fuchs Antenna matching unit QRPproject Molchstr. 15 12524 Berlin http://www.qrpproject.de Telefon: +49(30) 85 96 13 23 e-mail: support@qrpproject.de Handbucherstellung:
More informationAssembly and User Guide
1 Amp Adjustable Electronic Load 30V Max, 1 Amp, 20 Watts Powered by: 9V Battery Assembly and User Guide Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
More informationMAINTENANCE & ADJUSTMENT
MAINTENANCE & ADJUSTMENT Circuit Theory The concept of PLL system frequency synthesization is not of recent development, however, it has not been a long age since the digital theory has been couplet with
More informationSingle Transistor FM Transmitter Design
Single Transistor FM Transmitter Design In telecommunications, frequency modulation (FM) conveys information over a carrier wave by varying its frequency. FM is commonly used at VHF radio frequencies for
More informationThe basic set up for your K2 to run PSK31 By Glenn Maclean WA7SPY
The basic set up for your K2 to run PSK31 By Glenn Maclean WA7SPY I am by no means an expert on PSK31. This article is intended to help someone get on PSK31 with a K2. These are the things I did to get
More informationG4HUP Panoramic Adaptor Installation FT847
G4HUP Panoramic Adaptor Installation FT847 These instruction cover installation of the PAT board in the 1st IF of the FT847 45.705MHz this gives access to all receiver options on the main receiver. A a
More informationAssembly Instructions: Shortwave Radio Kit
Assembly Instructions: Shortwave Radio Kit MTM Scientific, Inc P.O. Box 522 Clinton, MI 49236 U.S.A Introduction Fig 1: The assembled Shortwave Radio Kit The SHORTWAVE RADIO KIT (#SWRAD) from MTM Scientific
More informationEH-20 20m antenna. By VE3RGW
EH-20 20m antenna By VE3RGW Equivalent circuit of EH-20 (prototype 2A) antenna system. Upper cylinder Lower cylinder Ground Counter pose Phasing coil Impedance transformer and tune circuit Tune coil Feed
More informationHear The Future...Now! SIEM-2T/SIEM-2R
Hear The Future...Now! SIEM-2T/SIEM-2R UHF PLL Mono In Ear Monitoring System 856 59508-03 ATTENTION Please pay high attention to the following information. The guideline published by Occupational Safety
More informationATS-505. GB Version 1
ATS-505 GB Version 1 Control Locations Power/Sleep Power On/off/Alarm off/sleep function Display Switch between radio frequency and time while radio is power on Mode Mode set up (please see below mode
More informationGermanium Diode AM Radio
Germanium Diode AM Radio LAB 3 3.1 Introduction In this laboratory exercise you will build a germanium diode based AM (Medium Wave) radio. Earliest radios used simple diode detector circuits. The diodes
More informationGLOLAB Universal Telephone Hold
GLOLAB Universal Telephone Hold 1 UNIVERSAL HOLD CIRCUIT If you have touch tone telephone service, you can now put a call on hold from any phone in the house, even from cordless phones and phones without
More informationModification of an AOR AR-8600 receiver to tune it with a ACECO FC-3002 frequency finder
Modification of an AOR AR-8600 receiver to tune it with a ACECO FC-3002 frequency finder Matthias DD1US updated June 2 nd 2011 Description of the ACECO FC-3002 unit: The ACECO FC-3002 is a handheld frequency
More informationKit 106. 50 Watt Audio Amplifier
Kit 106 50 Watt Audio Amplifier T his kit is based on an amazing IC amplifier module from ST Electronics, the TDA7294 It is intended for use as a high quality audio class AB amplifier in hi-fi applications
More informationK8025 VIDEO PATTERN GENERATOR. Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting.
K8025 ILLUSTRATED ASSEMBLY MANUAL H8025IP 1 VIDEO PATTERN GENERATOR Check the picture quality of your monitor or TV, ideal for adjustment or troubleshooting. Forum Participate our Velleman Projects Forum
More informationAUTOMATIC CALL RECORDER JAMECO PART NO. 2163735
AUTOMATIC CALL RECORDER JAMECO PART NO. 2163735 Experience Level: Intermediate Time Required: 1-2 Hours This project automatically records phone calls. The program, along with the adapter records each
More informationECEN 1400, Introduction to Analog and Digital Electronics
ECEN 1400, Introduction to Analog and Digital Electronics Lab 4: Power supply 1 INTRODUCTION This lab will span two lab periods. In this lab, you will create the power supply that transforms the AC wall
More informationMFRD52x. Mifare Contactless Smart Card Reader Reference Design. Document information
Rev. 2.1 17. April 2007 Preliminary Data Sheet Document information Info Keywords Content MFRC522, MFRC523, MFRC52x, MFRD522, MFRD523, Mifare Contactless Smart Card Reader Reference Design, Mifare Reader
More informationHomebrewing for QRP SSB
Homebrewing for QRP SSB First I would like to mention my website www.jessystems.com or in case you forget the site URL, just google my call sign N6QW. Many of my projects are documented there, complete
More informationThe G-QRP Club. The Limerick Sudden 40m Receiver Kit
The G-QRP Club The Limerick Sudden 40m Receiver Kit Circuit design George Dobbs G3RJV PCB design Rex Harper W1REX Kit parts spec and purchase Graham Firth G3MFJ Manual G3RJV and G3MFJ soku=j~ó=omnp= 1
More informationDX 2517. AM FM SSB CW PA Amateur Base Station Transceiver OWNER S MANUAL RX / TX 2 4 POWER NF CHANNEL MODE RF POWER OFF CAL OFF OFF CALIBRATE
1 2 3 6 4050 ULA 6070 TI 80 90 100 9 DX 2517 2517 RX / TX 0 2 4 SWR WATTS SET 81012 22 1 010 3 2030 5 MOD 7 ON dbover 9 SIGNAL +20 +40+60 PA FM AM USB LSB CW POWER ON SWR NB / ANL R.BEEP +10KHz NF CHANNEL
More informationAssembly Notes. Disclaimer:
Assembly Notes Before you start building your kit, please take time to read the manual in full at least once to enable you to fully understand the procedures and avoid any mistakes. The following notes
More informationSUPER SNOOPER BIG EAR
AA-1D Super Snooper Big Ear SPECIFICATIONS Operates on 5 to 9v DC Will drive a small speaker Provides up to 1 watt of audio power Distortion > 0.2% Voltage Gain up to 46 db Size: 1 x 1.95 Rainbowkits.com
More informationCircuit Board Sensor Products
Circuit Board Sensor Products AG21x-07 Cylinder Position Sensors PCB Assemblies for Pneumatic Cylinder Applications Features: Precision Magnetic Operate Point Three-Wire Current Source or Current Sink
More information200W DISCRETE POWER AMPLIFIER K8060
H8060IP-1 200W DISCRETE POWER AMPLIFIER K8060 Ideal for active speaker system or subwoofer, guitar amp, home theatre systems, instrument amp, etc. Features & Specifications Specifications: Excellent value
More informationVJ 6040 Mobile Digital TV UHF Antenna Evaluation Board
VISHAY VITRAMON Multilayer Chip Capacitors Application Note GENERAL is a multilayer ceramic chip antenna designed for receiving mobile digital TV transmissions in the UHF band. The target application for
More informationBuilding the HVPS High Voltage Power Supply
Introduction Building the HVPS High Voltage Power Supply Voltages higher than the LVPS provides kilovolts are needed in later experiments to get strong electric fields and to generate microwaves. The high-voltage
More informationRCForb Server Setup. Overview
RCForb Server Setup Overview The RcForb Server allows you to setup your own remote station on Remote Hams. Three connections to your transceiver are required, and an Internet connection. The first required
More informationPGA103+ Low noise, high dynamic range preamp for VHF and UHF
PGA103+ Low noise, high dynamic range preamp for VHF and UHF By Sam Jewell, G4DDK and Kent Britain, WA5VJB Introduction This paper describes a low noise, high dynamic range VHF/UHF preamp that uses the
More informationContents. Document information
User Manual Contents Document information... 2 Introduction... 3 Warnings... 3 Manufacturer... 3 Description... Installation... Configuration... Troubleshooting...11 Technical data...12 Device Scope: PCB
More informationPS 29M DUAL CHANNEL BELTPACK IN METAL CASE
PS 29M DUAL CHANNEL BELTPACK IN METAL CASE USER MANUAL October 2013 This product is designed and manufactured by: ASL Intercom BV Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax:
More informationXBee USB Adapter Board (#32400)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More information7-SEGMENT DIGITAL CLOCK
57mm 7-SEGMENT DIGITAL CLOCK Large 57mm clock & temperature display with extra unique feature Total solder points: 263 Difficulty level: beginner 1 2 3 4 5 advanced K8089 ILLUSTRATED ASSEMBLY MANUAL H8089IP-1
More informationThe RSGB Centenary Receiver Project Construction Manual
The RSGB Centenary Receiver Project Construction Manual Page 1 of 12 Introduction This project is intended for those new to radio construction. It is a fairly simple receiver for the 14MHz (20m) amateur
More informationDX 88HL OWNER S MANUAL. Full Channel AM/FM/SSB Mobile Built in Frequency Counter AM/FM 10W SSB 25W with Roger Beep
DX 88HL Full Channel AM/FM/SSB Mobile Built in Frequency Counter AM/FM 10W SSB 25W with Roger Beep Printed In Malaysia AT2100013P PD000929 OWNER S MANUAL TABLE OF CONTENTS Page Specification...................................
More informationSYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
More informationAmplifier for Small Magnetic and Electric Wideband Receiving Antennas (model AAA-1B)
Amplifier for Small Magnetic and Electric Wideband Receiving Antennas (model AAA-1B) 1. Description and Specifications Contents 1.1 Description 1.2 1.2 Specifications 1.3 1.3 Tested parameters in production
More informationPolyBot Board. User's Guide V1.11 9/20/08
PolyBot Board User's Guide V1.11 9/20/08 PolyBot Board v1.1 16 pin LCD connector 4-pin SPI port (can be used as digital I/O) 10 Analog inputs +5V GND GND JP_PWR 3-pin logic power jumper (short top 2 pins
More informationW8UM STATION EQUIPMENT DOCUMENTATION AMP-HF-SB-220. Date: 12/27/2006 Author: C. Galbraith KA8WFC Contact: (734) 678-2779
W8UM STATION EQUIPMENT DOCUMENTATION AMP-HF-SB-220 Equipment: Heathkit SB-220 HF Amplifier Scope: Description, Operation, History Date: 12/27/2006 Author: C. Galbraith KA8WFC Contact: cgalbrai@umich.edu,
More informationThe Radio-Kits Digital SWR meter kit Construction and user manual
The Radio-Kits Digital SWR meter kit Construction and user manual Author - Steve Drury G6ALU List of contents Section Page no. 1. Features and specifications 2 2. Introduction 2. Construction 4. General
More informationTS711 and TS811 CW PTT modification
TS711 and TS811 CW PTT modification Modification to the PTT circuitry in order to provide separate CW PTT applicable for Kenwood TS711 and TS811 radio s PC5M, C. Mobach Zuiderkreek 4 3832KJ Leusden The
More informationSUPERSTAR TABLE OF CONTENTS AM/FM/USB/LSB/CW AMATEUR MOBILE TRANSCEIVER WITH BUILT-IN FREQUENCY COUNTER OWNER S MANUAL. Downloaded from www.cbradio.
SUPERSTAR TABLE OF CONTENTS AM/FM/USB/LSB/CW AMATEUR MOBILE TRANSCEIVER WITH BUILT-IN FREQUENCY COUNTER PAGE CHAPTER 1 Specifications............................................... 2 CHAPTER 2 Installation.................................................
More informationCost. 13p each. 1.50 each
G-QRP Club components This is a service for G-QRP Club members only 6 pole crystal filter SSB 9MHz 2.2kHz 500 Ohm in/out 12 Polyvaricon capacitors 2 gang - 8 to 140pF & 6 to 60pF (tags marked A & O respectively)
More informationPS 155 WIRELESS INTERCOM USER MANUAL
PS 155 INTERFACE TO SIMPLEX WIRELESS INTERCOM USER MANUAL Issue 2011 ASL Intercom BV DESIGNED AND MANUFACTURED BY: ASL INTERCOM BV ZONNEBAAN 42 3542 EG UTRECHT THE NETHERLANDS PHONE: +31 (0)30 2411901
More informationA PIC16F628 controlled FLL (Frequency Locked Loop) VFO for HF
Abstract A PI6F628 controlled FLL (Frequency Locked Loop) VFO for HF It is described a device which joins in a single microprocessor a digital programmable frequency meter and a control logic capable to
More informationDET Practical Electronics (Intermediate 1)
DET Practical Electronics (Intermediate 1) 731 August 2000 HIGHER STILL DET Practical Electronics (Intermediate 1) Support Materials CONTENTS Section 1 Learning about Resistors Section 2 Learning about
More informationHow to Build the KN-Q7 40m SSB Transceiver
How to Build the KN-Q7 40m SSB Transceiver Design by BA6BF Text, drawings and photos by Andrew, ZL2PD (Website: www.zl2pd.com/index.html) Issue: B Introduction The KN-Q7 is a low power (QRP) transceiver
More informationUPDATED DOCUMENTATION---MOuSeFET TRANSMITTERS
UPDATED DOCUMENTATION---MOuSeFET TRANSMITTERS Updated information, improved circuitry and layout diagrams. Original article was in December, 1986 QST by Mike Masterson WN2A (formerly KA2HZA). Reprinted
More informationTEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT. Version 2.
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Index of Sheets TEACHING RESOURCES Index of Sheets
More informationINSTRUCTION MANUAL RM-5750. AM/FM Digital Alarm Clock Radio
INSTRUCTION MANUAL RM-5750 AM/FM Digital Alarm Clock Radio Fig. 1 CAUTION: THE APPARATUS SHALL NOT BE EX- POSED TO DRIPPING OR SPLASHING. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED
More informationCapacitor Self-Resonance
Capacitor Self-Resonance By: Dr. Mike Blewett University of Surrey United Kingdom Objective This Experiment will demonstrate some of the limitations of capacitors when used in Radio Frequency circuits.
More informationTV hearing aid BL-8008A BL-8008B. Manual
TV hearing aid BL-8008A BL-8008B Manual A. Product instruction 1. What is TV hearing aid 2. Theory 3. Features 4. Functions 4.1 TV hearing aid function 4.2 Normal hearing aid function 4.3 Wired hearing
More informationTotal solder points: 57 Difficulty level: beginner 1 2 3 4 5 advanced 3 TO 30VDC / 3A POWER SUPPLY K7203 ILLUSTRATED ASSEMBLY MANUAL H7203IP-1
Total solder points: 57 Difficulty level: beginner 1 2 3 4 5 advanced 3 TO 30VDC / 3A POWER SUPPLY K7203 A power supply for all our kits, based on a stabilised DC voltage of 30V. ILLUSTRATED ASSEMBLY MANUAL
More informationTHE R551N RECEIVER FAQ FAULT FINDING THE REDIFON COMMUNICATIONS RECEIVER R551N. Date: October 10th 1995 by: Jan Verduyn G5BBL
THE R551N RECEIVER FAQ FAULT FINDING THE REDIFON COMMUNICATIONS RECEIVER R551N Introduction: Date: October 10th 1995 by: Jan Verduyn G5BBL Recently a number of Redifon R551N receivers have appeared on
More informationThe new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu
The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifications and typographical errors reserved - Velleman nv. H8098 IP 2 (rev.1.0) Velleman NV, Legen
More information400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
More informationJoule Thief 3.0 Kit. June 2012, Rev 1 1 http://www.easternvoltageresearch.com Joule Thief 3.0
Kit Instruction Manual Eastern Voltage Research, LLC June 2012, Rev 1 1 http://www.easternvoltageresearch.com HIGH BRIGHTNESS LED THIS KIT USES A 1W CREE, HIGH BRIGHTNESS LED. DO NOT STARE AT THIS (OR
More informationSo this and all of my Modification Sheet are for education purposes only!
Introduction I started on doing modifications of CB- and HAM-radios since 1980 at the age of 12 years. I mostly wasn t satisfied with the sound of the modulation or reception of my rigs. This is normally
More informationRS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
More informationMEDIUM WAVE DX ANTENNA
THE HULA LOOP MEDIUM WAVE DX ANTENNA DESIGNED D BY SEAN GILBERT, G4UCJ The concept of the Hula Loop came after many years of building medium wave loops of varying size, shape and performance. Usually these
More informationDMX-K-DRV. Integrated Step Motor Driver + (Basic Controller) Manual
DMX-K-DRV Integrated Step Motor Driver + (Basic Controller) Manual DMX-K-DRV Manual page 1 rev 1.33 COPYRIGHT 2007 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.
More informationREALISTIC Stereo Three AM/FM Radio (120-1451) Features Faxback Doc. # 18906
REALISTIC Stereo Three AM/FM Radio (120-1451) Features Faxback Doc. # 18906 Your REALISTIC Stereo Three is a complete solid-state 3-piece FM/AM Stereo System. Its size and styling will fit well in any
More informationElectronics and Soldering Notes
Electronics and Soldering Notes The Tools You ll Need While there are literally one hundred tools for soldering, testing, and fixing electronic circuits, you only need a few to make robot. These tools
More information!Operation:!1. Connect an external power source to J1 (+ and - IN terminals). The
The CB500 Electronic Circuit Breaker is an resettable circuit breaker (fuse) that disconnects power when the trip setting is exceeded. There are 4 trip settings that can easily be changed and set during
More informationThe $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit.
The $25 Son of a cheap timer This is not suitable for a beginner. You must have soldering skills in order to build this kit. Micro Wizard has been manufacturing Pinewood Derby timers for over 10 years.
More informationFWT-8848 GSM (GATEWAY) USER S MANUAL
FWT-8848 GSM (GATEWAY) USER S MANUAL COPYRIGHT -2009 1 ST VERSION 1 1,General Description: FWT-8848 is a GSM to Analog Converter(single port,insert 1 sim card only), the device can produce a FXS line to
More informationUser Manual. For additional help please send a detailed e-mail to Support@phnxaudio.com. - 1 Phoenix Audio Technologies www.phnxaudio.
User Manual Please read the instructions in this manual before using the Duet Please refer to our website www.phnxaudio.com for more information, specifically to our Q&A section in our Support page. For
More informationWhale 3. User Manual and Installation Guide. DC Servo drive. Contents. 1. Safety, policy and warranty. 1.1. Safety notes. 1.2. Policy. 1.3. Warranty.
Whale 3 DC Servo drive User Manual and Installation Guide Contents 1. Safety, policy and warranty. 1.1. Safety notes. 1.2. Policy. 1.3. Warranty. 2. Electric specifications. 2.1.Operation ranges. 3. Connections
More informationHP 8970B Option 020. Service Manual Supplement
HP 8970B Option 020 Service Manual Supplement Service Manual Supplement HP 8970B Option 020 HP Part no. 08970-90115 Edition 1 May 1998 UNIX is a registered trademark of AT&T in the USA and other countries.
More informationstep 1 Unpack the lunchbox And check whether you have got all the components~ If you have questions please contact us at: info@unitunlikely.
step 1 Unpack the lunchbox And check whether you have got all the components~ If you have questions please contact us at: info@unitunlikely.com This part is called the PCB (printed circuit board). All
More informationAM TRANSMITTERS & RECEIVERS
Reading 30 Ron Bertrand VK2DQ http://www.radioelectronicschool.com AM TRANSMITTERS & RECEIVERS Revision: our definition of amplitude modulation. Amplitude modulation is when the modulating audio is combined
More informationTable of contents. Table of contents
Table of contents Table of contents 1 Appearance and Definition... 4 1.1 Appearance and Definition of 10-pin Interface... 4 1.1.1 Appearance... 4 1.1.2 MMP 10 pin definition... 5 1.1.3 MMP 10 electrical
More informationAmeritron ATP-102 Tuning Pulser II
Ameritron ATP-102 The Ameritron ATP-102 relieves temperature related stress on amplifiers, tuners, and dummy loads while allowing proper system adjustments. It allows amplifiers to be properly adjusted
More informationNC-12 Modbus Application
NC-12 Modbus Application NC-12 1 Table of Contents 1 Table of Contents... 2 2 Glossary... 3 SCADA...3 3 NC-12 Modbus in general... 3 4 Entire system... 4 4.1 PFC to PC connection alternatives...4 4.1.1
More informationGUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102
H4102IP-1 GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. Features & Specifications Features: An electric guitar cannot be connected to just any amplifier
More informationTELIKOU Intercom System. TM-200 Main Station. Instruction Manual
Intercom System TM-200 Main Station Instruction Manual TELIKOU Systems All Rights Reserved I. Introduction Thank you for choosing TELIKOU intercom product. TM-200 main station is suitable for television
More informationBUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
More informationRigExpert AA-30 Antenna Analyzer (0.1 to 30 MHz) AA-54 Antenna Analyzer (0.1 to 54 MHz) User s manual
RigExpert AA-30 Antenna Analyzer (0.1 to 30 MHz) AA-54 Antenna Analyzer (0.1 to 54 MHz) User s manual Table of contents 1. Description... 3 2. Specifications... 4 3. Precautions... 5 4. Operation... 6
More information28 Volt Input - 40 Watt
Features Powers 28 volt dc-dc converters during power dropout Input voltage 12 to 40 volts Operating temperature -55 to +125 C Reduces hold-up capacitance by 80% Inhibit function Synchronization function
More informationM2M 3350 GSM/GPRS Modem User s Manual & Reference Guide Revision 1 June 2007
M2M 3350 GSM/GPRS Modem User s Manual & Reference Guide Revision 1 June 2007 1999-2007 by Laipac Technology, Inc. All rights reserved The Specifications and information regarding the products in this manual
More informationVHF COMMUNICATION TRANSCEIVER
ATR-500 VHF COMMUNICATION TRANSCEIVER ON OFF OPERATION MANUAL Manual Number 01.125.010.08 REVISION 1.3, Jan 20. 2005 from S/N 00301 04 Contents 1 SECTION 1 GENERAL INFORMATION...3 1.1 INTRODUCTION...3
More informationMicrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.
Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.1 The Micrio WS1 Wind Speed Sensor and WC1 Compass Sensor are direct
More informationUser Manual CABLE TESTER CT100. Professional 6-in-1 Cable Tester
User Manual CABLE TESTER CT100 Professional 6-in-1 Cable Tester 2 CABLE TESTER CT100 User Manual 1. Introduction Congratulations! With the CT100, you have purchased an indispensable tool that enables you
More informationTQP4M3019 Data Sheet. SP3T High Power 2.6V 2x2 mm CDMA Antenna Switch. Functional Block Diagram. Features. Product Description.
Functional Block Diagram Product Description TriQuint s TQP4M3019 is a high power antenna switch in a single pole three throw (SP3T) configuration. The die utilizes TriQuint s PHEMT MMIC switch process
More informationHigh voltage power supply (1 to 20 KV)
High voltage power supply ( to 0 KV) Ammar Ahmed Khan, Muhammad Wasif, Muhammad Sabieh Anwar This documentation is divided into two parts, the first part provides a brief overview about the key features
More informationAlarm over IP. IRIS Touch Home Installation Manual. Version 1.0 ENGLISH. Now certified and compliant with EN50131, EN50136 Security Grade 4 ATS6
Alarm over IP IRIS Touch Home Installation Manual Version 1.0 ENGLISH Now certified and compliant with EN50131, EN50136 Security Grade 4 ATS6 1. Introduction No more bulky batteries, just one sleek unit
More informationTHE KW107 SUPERMATCH ATU manual, courtesy of Barry G0DWZ
THE KW107 SUPERMATCH ATU manual, courtesy of Barry G0DWZ I ve copied the following directly from the KW107 manual without alteration. To clear up one or two ambiguous points, I have added my own comments
More informationMARS-ALE Application Note. RS-232 Computer Control Interface for LDG Electronics DTS-4/DTS-6 Desktop Coaxial Switches. Version 1.
MARS-ALE Application Note RS-232 Computer Control Interface for LDG Electronics DTS-4/DTS-6 Desktop Coaxial Switches Version 1.02 08 April 2006 POC for this document is AAR2EY/NJ U.S. Army MARS aar2ey@usarmymars.us
More informationAM/FM Component Stereo Receiver System (120-1470) Preparation Faxback Doc. # 18708
AM/FM Component Stereo Receiver System (120-1470) Preparation Faxback Doc. # 18708 POWER REQUIREMENTS Connect the AC line cord into any outlet furnishing 117 volts 50-60 cycles AC current. CONNECTING SPEAKERS
More informationOPERATING MANUAL VARIABLE ATTENUATOR AND INTERFACE BOX -12- AUDIO OUT CABLE WIRING HI-Z
KACHINA DRAKE T4XB COLLINS S, S COLLINS KWMA AUDIO OUT CABLE WIRING COLLINS V, V, KWS Hallicrafters E.F. Johnson DRAKE TR7 + Mic - Mic 8 Pin Mic Connector Pin 8 Pin Mic Connector Pin 8 Pin Mic Connector
More informationTotal solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 167 Difficulty level: beginner 1 2 3 4 5 advanced DMX CONTROLLED RELAY K8072 Control a relay by means of the wellknown DMX512 protocol. ILLUSTRATED ASSEMBLY MANUAL H8072IP-1 Features
More informationFM TRANSMITTER & RECEIVER HYBRID MODULES. FM-RTFQ SERIES FM-RRFQ SERIES. Transmitter. Receiver. Applications
FM Radio Transmitter & Receivers Available as or or 868MHz Transmit Range up to 20m Miniature Packages Data Rate up to 9.6Kbps No Adjustable Components Very Stable Operating Frequency Operates from 20
More informationIntroduction Ericsson Handheld Telephone 1341-B
Ericsson Handheld Telephone 1341-B 2 Contents General 5 The Mobile Telephone Network 6 Base Station and Cell 7 Radio Channels 7 Radio Coverage 8 Transmission Control and Communication 9 Quality Control
More informationPortavision-50 AM/FM/TV1/TV2 Portable Radio (120-0687) Features Faxback Doc. #
(120-0687) Features Faxback Doc. # Your Portavision-50 AM/FM/TV1/TV2 Portable Radio lets you hear your favorite television shows wherever you go. Set it on your desk, or take it with you in your car to
More information