CLASS-C. Installation manual: Parrot MKi + Parrot CK3100 range CLASS-C (W203)

Transcription

1 Installation manual: Parrot MKi + Parrot CK3100 range CLASS-C (W203) This The brand sheet name is designed MERCEDES-BENZ to help you CLASS-C with the and installation the MERCEDES of a Parrot logo are product the property and is provided of MERCEDES. purely for information purposes. The installer is solely This document responsible is only for valid any installation for the vehicle carried model out CLASS-C in accordance year 2000 with to the 2007, instructions excluding in all this other sheet models and for in the same quality range of the and installation. excluding later All rights modifications reserved made Copyright to the vehicle 2011 by PARROT the manufacturer. SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies The Parrot brand Register name under and logos No. 394 are 149 the exclusive 496 Reproduction property of not Parrot permitted SA. without authorisation from Parrot SA. Images not contractually

2 Fitting time (estimated) / Main features Disassembly 40min NO ACC wire Kit installation Refitting Testing 45min 40min 15min YES* / NO YES (with the reserve of steering wheel coding) ISO UNIKA Total 2h10min FRONT SPEAKER ALL TEL mode MUSIC mode Tools Plastic trim removal tools FACOM / BERNER -TORX screwdriver - Cutting pliers - Crimping pliers - Multimeter or pilot lamp MERCEDES factory tool: Hose clamp - Electrical tape - Round male terminal - Jumper - Semi-rigid guide

3 Accessories required CK range MKi range Kram ref. Dealer ref. CK range PC000033AA MKi range PC000033AA Photos not contractually binding Quick Connect harness references available at Updating To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at Comments - Remarks ATTENTION: For vehicles equipped with the AUDIO 5 radio, the connection is by ISO. For vehicles equipped with the AUDIO 20 or AUDIO 50 radio, the connection is by FAKRA and requires an adaptor.

4 Disassembly

5 Disassembly 1 / Using the plastic trim tools, unclip the gear lever cover and remove the bellows. Using the plastic trim tools, unclip the ashtray and cigarette lighter assembly, then place it to the side being careful not to disconnect it Under the air conditioning unit. Remove screws 1 and Using the plastic trim tools, unclip the air conditioning cover taking care not to disconnect it. Make a quarter turn upwards on the ventilation slots and remove screws 3 and 4 on the bottom.

6 Disassembly 2 / Make a quarter turn downwards on the ventilation slots and insert the Remove screws 5 and 6 above MERCEDES removal tool. Then make a the WARNING cover. Then quarter turn to unclip it and pull the air remove it without disconnecting vents. it Unscrew screws 7 and 8 located Unscrew screws 9 and 10 located under above the radio. the radio unit, then pull and disconnect the connector and antennas Remove the rubber cover in the centre console. Unclip the coin tray by rotating to the left.

7 Disassembly 3 / Unclip the joint. Unscrew screws 11, 12 and 13 located under the glove box Unfasten and half open the cover. Unclip the cabin light and allow it to hang down without disconnecting it Using the plastic trim tools, unclip the passenger side of the dashboard. Remove the passenger door seal.

8 Finding an ACC wire 1 2 Using a guide, pass an electric wire from the cigarette lighter to the underneath of the air conditioning control housing. Make a pigtail connection (or use the jumper) to the 9 BLACK/YELLOW wire. 3 4 Attach the electric wire and insulate with electrical tape. (With the Multimeter, check that the V is properly controlled by the key.) For the Audio 5 car radio (also applies to PC000033AA), swap the fuses on the kit's original connector. (i.e. The red and orange wires.) Cut the red wire between the fuse holder and the ISO connector, then connect to the ACC wire. OR For adaptor 84099, (Mki range only) connect the ACC wire with a male round terminal to the blue wire at the front of the fuse holder.

9 Microphone passage Feed the cable under the rear view mirror arm towards the cabin light. Glue the bracket (supplied) to the rear view mirror arm, after carefully cleaning the surface, then refit the cabin light. 4 5 Using the plastic trim tools, run the cable along the windscreen. Slide the cable along the passenger door pillar while replacing the door seal. 6 Pass the cable through the passenger side of the dashboard. Pass the cable under the glove box towards the radio housing.

10 Feeding the accessory cable 1 2 Using a drill, make a hole with diameter 22 and feed the cable (supplied) through. Refit the insert. 3 4 Clip the coin tray back on. Replace the rubber cover. 5 Be careful to feed through enough of the cable.

11 Fitting the hands-free system 1 / 3 1 Connect the factory connector, invert the fuses (i.e. the RED and ORANGE wires) then cut the RED wire between the fuse holder and the ISO connector and connect the ACC wire above. For cars with the AUDIO 20 and 50: Use adapter 86111/PC000033AA and the factory connector for CK (same mounting as AUDIO 5) or 84099/PC000033AA for MKI. (For the PC000033AA add the factory connector and the same mounting as the AUDIO 5.) 2 For the adapter 84099, remove the terminals from the blue wire in front of the fuse holder. Then mount a round female terminal on the ACC wire and connect it to the blue wire.

12 Fitting the hands-free system 2 / 3 3 Connect all the cables on the blue box as shown on the diagram below, then test before reassembling. Then slide the assembly behind the air conditioning control unit. Direct adaptor cable

13 Fitting the hands-free system 3 / Feed the cable through the side of the vents situated near the bottom screw. Glue the support (supplied) after cleaning, to the buttons on the WARNING panel. 6 Pass the cable towards the air conditioning housing.

14 Testing Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob of the remote control, check: 1 - That the menu is displayed on the screen (language or ipod.) 2 - That the system can be muted. (Click in the blue box.) 3 - That there is no sound coming from the speakers. 4 - That the sound from the voice menu is coming out of the front speakers. 5 - Then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen. (if this fails, reverse the fuses on the kit's wiring harness.) 6 - Pair a telephone with the kit to make a call. (Check that both the microphone and the kit are working.)

15 Reassembly Refit the system using the following procedure: 1 - Reconnect the radio (and the antennas) and slide it into its housing. 2 - Refit the 4 screws (7, 8, 9 and 10) for the car stereo. 3 - Clip the WARNING panel back on and replace screws 5 and Clip the central air vent back on (be careful with the screen cable), make a quarter turn and refit screws 3 and Clip the air conditioning cover back on and replace screws 1 and Re-clip the ashtray. 7 - Re-clip the central cover. 8 - Replace the 3 screws (11, 12 and 13) located under the glove box. 9 - Refit the right dashboard panel. 10 Re-test to check that the system is working correctly.