Aerospace series Aluminium alloy AL-P7175- Al Zn5,5MgCu(B) - T73511 Extruded bar and section a or D 150 mm
|
|
- Jeffry Wiggins
- 7 years ago
- Views:
Transcription
1 AECMA STANDARD NORME AECMA AECMA NORM pren 4293 Edition P 2 July 2010 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 B-1200 BRUXELLES Tel. (+32) Fax. (+32) ICS: Descriptors: ENGLISH VERSION Aerospace series Aluminium alloy AL-P7175- Al Zn5,5MgCu(B) Extruded bar and section a or D 150 mm Série aérospatiale Alliage d'aluminium AL-P7175- Al Zn5,5MgCu(B) Barres et profilés filés a ou D 150 mm Luft- und Raumfahrt Aluminiumlegierung AL-P7175- Al Zn5,5MgCu(B) Stranggepreβte Stangen und Profile a oder D 150 mm This "Aerospace Series" Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote.
2 Page 2 Blank page
3 Page 3 0 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN This standard has been prepared in accordance with EN Scope This standard specifies the requirements relating to: for aerospace applications. Aluminium alloy AL-P7175- Al Zn5,5MgCu(B) Extruded bar and section a or D 150 mm 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2043 EN EN 4258 EN Aerospace series - Metallic materials - General requirements for semi-finished product qualification (excluding forgings and castings) 1) Aerospace series - Aluminium and aluminium alloy wrought products - Technical Specification - Part 3: Bar and section Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use 1) Aerospace series - Metallic materials - Rules for drafting and presentation of material standards - Part 2: Specific rules for aluminium, aluminium alloys and magnesium alloys 1) 1) Published as AECMA Prestandard at the date of publication of this standard
4 Page 4 1 Material designation Aluminium alloy AL-P7175- Al Zn5,5MgCu(B) 2 Chemical Element Si Fe Cu Mn Mg Cr Zn Ti Others Al Each Total composition min. 1,2 2,1 0,18 5,1 % max. 0,15 0,20 2,0 0,10 2,9 0,28 6,1 0,10 0,05 0,15 3 Method of melting 4.1 Form Bar and section 4.2 Method of production Extruded 4.3 Limit dimension(s) mm a or D Technical specification EN Base 6.1 Delivery condition T73511 Heat treatment 455 C θ 475 C / WQ θ 40 C + 1 % controlled stretched 3 % + minor straightening C θ 125 C / 6 h t 24 h C θ 182 C / 6 h t 16 h 6.2 Delivery condition code U 7 Use condition T73511 Heat treatment Delivery condition Characteristics 8.1 Test sample(s) See EN Test piece(s) See EN Heat treatment Use condition 9 Dimensions concerned mm a or D < a or D < a or D < a or D < a or D < a or D Thickness of cladding on each face % 11 Direction of test piece L L L L L L 12 Temperature θ C Ambient Ambient Ambient Ambient Ambient Ambient 13 Proof stress R p 0,2 MPa T Strength R m MPa Elongation A % 8 1) Reduction of area Z % 17 Hardness 18 Shear strength R c MPa 19 Bending k 20 Impact strength 21 Temperature θ C 22 Time h 23 Stress σ a MPa 24 C Elongation a % 25 Rupture stress σ R MPa 26 Elongation at rupture A % 27 Notes (see line 98) 1)
5 Page 5 32 Electrical conductivity See EN Measurement on the surface of the sample from which tensile specimens are taken. 7 γ 23 MS/m Acceptable 22 MS/m γ < 23 MS/m Acceptable if Rp0,2 L Rp0,2 min. L + 85 MPa or if stress corrosion test acceptable γ < 22 MS/m Non acceptable 39 Stress corrosion See EN For qualification 3 a or D > 25 mm 6 σ = 70 % R p0,2 min. L 7 t = 20 days 40 Fracture toughness See EN (K IC ) 7 Dimensions (mm) For qualification 40 a or D External defects See EN T - L MPa m 51 Macrostructure See EN Internal defects See EN Batch uniformity See EN Electrical conductivity or T73511 Hardness γ MS/m See EN HB 140 (typical value) δ 20 per product 95 marking inspection See EN Δ 30 per batch 96 Dimensional inspection See EN Notes 1) or A 50mm 7% 99 Typical use
6 Page Product qualification See EN Qualification programme to be agreed between manufacturer and purchaser.
ALLOY 7475 PLATE AND SHEET HIGHEST TOUGHNESS/STRENGTH
ALCOA MILL PRODUCTS ALLOY 7475 PLATE AND SHEET HIGHEST TOUGHNESS/STRENGTH ALLOY 7475 DESCRIPTION Alloy 7475 is a controlled toughness alloy developed by Alcoa for sheet and plate applications that require
More information% Si Fe Cu Mn Mg Cr Zn Ti Others Others. Europe USA Spain France Germany G.B. Italy Sweden Switzerland Japan. ALMgSi1 3.3215 H30
ALUMINIUMS Alloys Aluminium - Magnesium - Silicon 6082 % Si Fe Cu Mn Mg Cr Zn Ti Others Others Minimum 0,70 0,40 0,60 Each Total Maximum 1,30 0,50 0,10 1,00 1,20 0,25 0,20 0,10 0,05 0,10 Europe USA Spain
More informationASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-
Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and
More informationMaterial data sheet. EOS Aluminium AlSi10Mg_200C. Description
EOS Aluminium AlSi10Mg_200C All information in this data sheet refers to the alloy EOS Aluminium AlSi10Mg_200C. This alloy is formed when the powder EOS Aluminium AlSi10Mg is processes at a building platform
More informationMaterial data sheet. EOS Aluminium AlSi10Mg. Description
EOS Aluminium AlSi10Mg EOS Aluminium AlSi10Mg is an aluminium alloy in fine powder form which has been specially optimised for processing on EOSINT M systems This document provides information and data
More informationMaterial data sheet. EOS StainlessSteel GP1 for EOSINT M 270. Description, application
EOS StainlessSteel GP1 for EOSINT M 270 A number of different materials are available for use with EOSINT M systems, offering a broad range of e-manufacturing applications. EOS StainlessSteel GP1 is a
More informationEnglish version. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 4162 2012 ICS: 49.030.20 English version Aerospace series Screws 100 countersunk normal head, offset cruciform recess, coarse tolerance normal shank,
More informationMaterial data sheet. EOS CobaltChrome MP1. Description
EOS CobaltChrome MP1 EOS CobaltChrome MP1 is a cobalt-chrome-molybdenum-based superalloy powder which has been optimized especially for processing on EOSINT M systems. This document provides information
More informationALLOY 6022 SHEET. Higher Strength with Improved Formability SUPPLYING THE WORLD S BEST
SUPPLYING THE WORLD S BEST DESCRIPTION 6022 is a heat treatable low copper, Al-Si-Mg sheet alloy developed by Alcoa to satisfy the needs of automotive manufacturers for closure panels, such as a hood,
More informationAluminium alloys Extrusions and forgings
AI Extrusions and forgings AI Extrusions and forgings Aluminium wrought alloys are the light alloys with the most balanced properties. Beside their low specific weight they may also have the following
More informationROLLED STAINLESS STEEL PLATES, SECTIONS AND BARS
STANDARD FOR CERTIFICATION No. 2.9 ROLLED STAINLESS STEEL PLATES, SECTIONS AND BARS OCTOBER 2008 Veritasveien 1, NO-1322 Høvik, Norway Tel.: +47 67 57 99 00 Fax: +47 67 57 99 11 FOREWORD (DNV) is an autonomous
More informationWear-resistant steels. Technical terms of delivery for heavy plates. voestalpine Grobblech GmbH www.voestalpine.com/grobblech
Wear-resistant steels Technical terms of delivery for heavy plates voestalpine Grobblech GmbH www.voestalpine.com/grobblech Wear-resistant steels durostat durostat 400 durostat 450 durostat 500 durostat
More informationMetal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
More informationAUSTENITIC STAINLESS DAMASCENE STEEL
AUSTENITIC STAINLESS DAMASCENE STEEL Damasteel s austenitic stainless Damascene Steel is a mix between types 304L and 316L stainless steels which are variations of the 18 percent chromium 8 percent nickel
More informationME 612 Metal Forming and Theory of Plasticity. 1. Introduction
Metal Forming and Theory of Plasticity Yrd.Doç. e mail: azsenalp@gyte.edu.tr Makine Mühendisliği Bölümü Gebze Yüksek Teknoloji Enstitüsü In general, it is possible to evaluate metal forming operations
More informationHot rolled products of structural steels
BRITISH STANDARD BS EN 10025-6:2004 +A1:2009 Hot rolled products of structural steels Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and
More informationLoose steel tubes for tube and coupler scaffolds Technical delivery conditions
BRITISH STANDARD BS Loose steel tubes for tube and coupler scaffolds Technical delivery conditions The European Standard has the status of a British Standard ICS 77.140.75; 91.220 NO COPYING WITHOUT BSI
More informationJIS G3445 Carbon steel tubes for machine structural purposes
JIS G3445 arbon steel tubes for machine structural purposes 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for machinery, automobiles,
More informationSAND CAST CHILL CAST LM4 - TF
1 This alloy conforms with British Standards 1490 and is similar to the obsolete specifications BS.L79 and D.T.D 424A. Castings may be in the cast (M) of fully heat treated (TF) conditions. CHEMICAL COMPOSITION
More informationX15TN TM. A high hardness, corrosion and fatigue resistance martensitic grade CONTINUOUS INNOVATION RESEARCH SERVICE.
TM A high hardness, corrosion and fatigue resistance martensitic grade CONTINUOUS METALLURGICAL SPECIAL STEELS INNOVATION RESEARCH SERVICE DEVELOPMENT Enhancing your performance THE INDUSTRIAL ENVIRONMENT
More informationStandard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications 1
Designation: A 2/A 2M 04a e1 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications 1 This standard is issued
More informationStandard Specification for Stainless Steel Bars and Shapes 1
Designation: A 276 06 Standard Specification for Stainless Steel Bars and Shapes 1 This standard is issued under the fixed designation A 276; the number immediately following the designation indicates
More informationDIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES
DIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES For connection with the International Draft Standards 3183 and 3845 published by the International Organization
More informationHigh Strength Aluminium Fasteners. 25.04.2006 G. Ross/R. Eul
High Strength Aluminium Fasteners 25.04.2006 G. Ross/R. Eul Content: TFS Key Facts Aluminium Fastener History Advantages & Benefits Applications Characteristics - Stress Corrosion Cracking - Fatigue Resistance
More informationBUMAX. REYHER your partner for the BUMAX range
BUMAX high-tensile stainless steel fasteners REYHER your partner for the BUMAX range Strongest stainless steel fasteners in the world BUMAX 88 and BUMAX ready for delivery from stock Wide range of BUMAX
More informationSTRUCTURAL STEELS. Steel Grades S185 S235JR S235JRG2 S235JO S235J2G3 S235J2G4 S275JR S275JO S275J2G3 S275J2G4 S355JR S355JO S355J2G3 S355J2G4
STRUCTURAL STEELS Steel Grades S185 S235JR S235JRG2 S235JO S235J2G3 S235J2G4 S275JR S275JO S275J2G3 S275J2G4 S355JR S355JO S355J2G3 S355J2G4 S355K2G3 S355K2G4 E295 E335 E360 STRUCTURAL STEELS The unalloyed
More informationCaps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Sheet T409 INTRODUCTION NAS 409 is an 11% chromium, stabilized ferritic stainless steel. It is not as resistant to corrosion or high-temperature oxidation
More informationSteel tubes for precision applications Technical delivery conditions
BRITISH STANDARD Steel tubes for precision applications Technical delivery conditions Part 2: Welded cold drawn tubes The European Standard EN 10305-2:2002 has the status of a British Standard ICS 77.140.75
More informationJIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes 1. Scope This Japanese Industrial Standard specifies the electric resistance welded carbon steel tubes, hereinafter
More informationADDENDUM TO 2011 TAN SHEETS. Tempers For Aluminum And Aluminum Alloy Products Metric July 16, 2013. New and Revised Registrations
s For Aluminum And Aluminum s Metric July 1, 201 By Date Over Thru Basis 1 Ult. Yield 0 mm 201T11 Sumitomo 0/01/2012 Drawn Tube D or. A.00.00 2 1 20 * Tentative 201T11 Sumitomo 12/1/2011 Drawn Tube 22T1
More informationGENERAL PROPERTIES //////////////////////////////////////////////////////
ALLOY 625 DATA SHEET //// Alloy 625 (UNS designation N06625) is a nickel-chromium-molybdenum alloy possessing excellent resistance to oxidation and corrosion over a broad range of corrosive conditions,
More informationRules for Classification and Construction Materials and Welding
II Rules for Classification and Construction Materials and Welding 1 Metallic Materials 2 Steel and Iron Materials Edition 2009 The following Rules come into force on April 1 st, 2009 Alterations to the
More informationSteel tubes for precision applications Technical delivery conditions
BRITISH STANDARD BS EN 10305-4:2003 Steel tubes for precision applications Technical delivery conditions Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems The European Standard
More informationÖNORM EN 1504-8. The European Standard EN 1504-8 has the status of an Austrian Standard. Edition: 2005-02-01. Standards group B
ÖNORM EN 1504-8 Edition: 2005-02-01 Standards group B Identical (IDT) with EN 1504-8:2004 ICS 91.080.40 Products and systems for the protection and repair of concrete structures Definitions, requirements,
More informationAdditive Manufacturing applications in Aerospace, Automotive, Robotics and beyond
Additive Manufacturing applications in Aerospace, Automotive, Robotics and beyond JGIF 2015 Tokio, 9th of November 2015 Joachim Zettler Airbus Apworks GmbH Airbus APWorks Founded in 2013 A perfectly harmonized
More informationAluminium and aluminium alloys Ð Extruded rod/bar, tube and profiles Ð
BRITISH STANDARD BS EN 755-7:1998 The European Standard has the status of a British Standard ICS 23.4.15; 77.15.1 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Aluminium and aluminium
More informationHigh tensile strength stainless fasteners
High tensile strength stainless fasteners BUFAB STAINLESS HISTORY 1674 Svartå Bruk was founded 1912 Svartå Bruk was incorporated into the Hasselfors group. 1947 Production of Stainless Steel Fasteners
More informationS355 European Standard Steel
1(7) S European Standard Steel S EN 10025 : 2004 Standard Plate S structural steel plate is a highstrength lowalloy European standard structural steel covering four of the six "Parts" within the EN 10025
More informationFINAL DRAFT PREN ISO 14327 RESISTANCE WELDING PROCEDURES FOR DETERMINING THE WELDABILITY LOBE FOR RESISTANCE SPOT, PROJECTION AND SEAM
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG CEN/TC 121 N 1060 FINAL DRAFT PREN ISO 14327 RESISTANCE WELDING PROCEDURES FOR DETERMINING THE WELDABILITY
More informationCrystal Structure of Aluminum, Zinc, and their Alloys By: Omar Fajardo Sebastian Henao Devin Baines ENGR45, F2014, SRJC
Crystal Structure of Aluminum, Zinc, and their Alloys By: Omar Fajardo Sebastian Henao Devin Baines ENGR45, F2014, SRJC Purpose The purpose of this experiment was to examine and observe the microstructure
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet 2205 UNS S2205 EN 1.4462 2304 UNS S2304 EN 1.4362 INTRODUCTION Types 2205 and 2304 are duplex stainless steel grades with a microstructure,
More informationNon-destructive testing of steel forgings - Part 2: Penetrant testing (BS EN 10228-2:1998)
Non-destructive testing of steel forgings - Part 2: Penetrant testing (BS EN 10228-2:1998) 1 Scope This part of EN 10228 describes the method and acceptance criteria to be used for the penetrant testing
More informationSteel rod, bars and wire for cold heading and cold extrusion
BRITISH STANDARD rod, bars and wire for cold heading and cold extrusion Part 5: Technical delivery conditions for stainless steels The European Standard has the status of a British Standard ICS 77.140.60;
More informationHow To Write A Recipe Card
Forging stock standards guideline Issue n 10 FORGING STOCK 30 Microstructure 34 Grain size Air melted (except if δ ferrite or problem 1 per batch) 50 Cleanness/ Inclusion See EN 2157-2. 51 Macrostructure
More informationADDENDUM TO 2011 TAN SHEETS Tempers For Aluminum And Aluminum Alloy Products Metric Edition June, 2014. New and Revised Registrations
s For Aluminum And Aluminum s Metric Edition June, 201 By Date Over Thru Basis 1 Ult. Yield 201T11 Sumitomo 0/01/2012 Drawn Tube 0 D or. A.00.00 2 1 20 * Tentative 201T11 Sumitomo 12/1/2011 Drawn Tube.00.00
More informationALUMINIUM. Conductors
ALUMINIUM Conductors TABLE OF CONTENTS The ALUMINIUM AND ALUMINIUM ALLOYS WIRES technical data Aluminium wires...p 3 in this catalog Hard aluminium are given for _hard aluminium information Other states
More informationStandard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1
Designation: A 213/A 213M 03b Used in USDOE-NE standards Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes 1 This standard is issued
More informationSeamless stainless tubes for hydraulic and instrumentation systems
Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes
More informationINFORMAZIONI GENERALI / GENERAL INFORMATION
INFORMAZIONI GENERALI / GENERAL INFORMATION LE FLANGE DELLA SOCIETà INTERTUBI SONO FORNITE IN ACCORDO ALLE SEGUENTI NORME: INTERTUBI S FLANGES ARE PROVIDED IN ACCORDING WITH THE FOLLOWINGS STANDARDS Norma
More informationValve Steel. Valve Steel
Valve Steel Valve Steel BÖHLER-UDDEHOLM Precision Strip AB is one of the world s leading manufacturers of high quality strip steel. More than a century s experience of cold rolling has given us a unique
More informationStainless steel grade chart
Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0
More informationChapter 2 Fractal Analysis in CNC End Milling
Chapter 2 Fractal Analysis in CNC End Milling Abstract This chapter deals with the fractal dimension modeling in CNC end milling operation. Milling operations are carried out for three different materials
More informationMaterial data sheet. EOS MaragingSteel MS1. Description
EOS MaragingSteel MS1 EOS MaragingSteel MS1 is a steel powder which has been optimized especially for processing on EOSINT M systems. This document provides information and data for parts built using EOS
More informationDX2202 Duplex stainless steel
Stainless Europe Grade DX22 Duplex stainless steel Chemical Composition Elements C Mn Cr Ni Mo N %.25.3 23. 2.5
More informationAppendice Caratteristiche Dettagliate dei Materiali Utilizzati
Appendice Caratteristiche Dettagliate dei Materiali Utilizzati A.1 Materiale AISI 9840 UNI 38NiCrMo4 AISI 9840 Steel, 650 C (1200 F) temper, 25 mm (1 in.) round Material Notes: Quenched, 540 C temper,
More informationNorth American Stainless Long Products
North American Stainless Long Products 1 North American Stainless North American Stainless is part of the most competitive stainless steel manufacturing group in the world, Acerinox, S.A. The development
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60502-1 Second edition 2004-04 Power cables with extruded insulation and their accessories for rated voltages from 1 kv (U m = 1,2 kv) up to 30 kv (U m = 36 kv) Part 1: Cables
More informationWEIGHTS AND MASS STANDARDS
WEIGHTS AND MASS STANDARDS IN ACCORDANCE WITH THE OIML R111: 2004 MADE BY WEEGTECHNIEK HOLLAND B.V. Patroonsweg 23-27 3892 DA Zeewolde The netherlands Tel. +31 (0)36-5222030 Fax. +31 (0)36-5222060 E-mail:
More informationNEW ALUMINUM LITHIUM ALLOYS FOR AEROSPACE APPLICATIONS
Proceedings of the Light Metals Technology Conference 2007 NEW ALUMINUM LITHIUM ALLOYS FOR AEROSPACE APPLICATIONS Cindie Giummarra 1, Bruce Thomas 2 and Roberto J. Rioja 1 1 Alcoa, 100 Technical Drive,
More informationMechanical Properties of Metals Mechanical Properties refers to the behavior of material when external forces are applied
Mechanical Properties of Metals Mechanical Properties refers to the behavior of material when external forces are applied Stress and strain fracture or engineering point of view: allows to predict the
More informationTECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR 1.1.0 SCOPE : This specification covers design, manufacture, testing at manufacture s works before
More informationJIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger
JIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for exchanging heat
More informationUnit 6: EXTRUSION. Difficult to form metals like stainless steels, nickel based alloys and high temperature metals can also be extruded.
1 Unit 6: EXTRUSION Introduction: Extrusion is a metal working process in which cross section of metal is reduced by forcing the metal through a die orifice under high pressure. It is used to produce cylindrical
More informationCold drawn seamless steel tubes for mechanical applications
Cold drawn seamless steel tubes for mechanical applications Cold drawn precision seamless tubes for mechanical and general engineering applications. Available in various steel grades, according to the
More informationAluminium as Construction Material in Ammonia Refrigeration Cycles
Aluminium as Construction Material in Ammonia Refrigeration Cycles Experiences With Aluminium Compared to other metals, aluminium has only a brief history as an engineering material. While, about 150 years
More informationHeat Treatment of Aluminum Foundry Alloys. Fred Major Rio Tinto Alcan
Heat Treatment of Aluminum Foundry Alloys Fred Major Rio Tinto Alcan OUTLINE Basics of Heat Treatment (What is happening to the metal at each step). Atomic Structure of Aluminum Deformation Mechanisms
More informationPierre Marchand, product director, speciality product Meeting NEI-NRC March 14th 2013
Pierre Marchand, product director, speciality product Meeting NEI-NRC March 14th 2013 Agenda Dubuc works: location and overview MMC fabrication process at Rio Tinto Alcan Boralcan product caracteristics
More informationMATERIAL SPECIFICATIONS CATALOGUE
MATERIAL SPECIFICATIONS CATALOGUE Manganese Steel High Chrome White Iron Alloy Steel Carbon Steel Stainless Steel SG Iron Cast Iron E X C E L L E N C E T H R O U G H E X P E R I E N C E Foundries has the
More informationGuiding Principles for the contents of Particular Materials Appraisals (Version approved at the WGP on 21 November 2006)
PE- 03-28 - rev 5 21 November 2006 Page 1 of 5 Guiding Principles for the contents of Particular Materials Appraisals (Version approved at the WGP on 21 November 2006) Introduction A Particular Material
More informationVdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 430 (S43000)/ EN 1.4016 Introduction: SS430 is a low-carbon plain chromium, ferritic stainless steel without any stabilization of carbon
More informationALLOY 2205 DATA SHEET
ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,
More informationNaue GmbH&Co.KG. Quality Control and. Quality Assurance. Manual. For Geomembranes
Naue GmbH&Co.KG Quality Control and Quality Assurance Manual For Geomembranes July 2004 V.O TABLE OF CONTENTS 1. Introduction 2. Quality Assurance and Control 2.1 General 2.2 Quality management acc. to
More informationHEAT TREATMENT EFFECT ON MECHANICAL PROPERTIES AND SEM ANALYSIS OF AL6061/WC/B 4 C/TI/CR METAL MATRIX COMPOSITES
International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 2, March-April 2016, pp. 232 243, Article ID: IJMET_07_02_025 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=2
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet AISI 304 UNS S30400 EN 1.4301 AISI 304L UNS S30430 EN 1.4307 INTRODUCTION: Types 304 and 304L are the most versatile and widely used of
More informationSteel Reinforcing Bars for the Reinforcement of Concrete
Construction Standard CS2:2012 Steel Reinforcing Bars for the Reinforcement of Concrete 香 港 特 別 行 政 區 政 府 The Government of the Hong Kong Special Administrative Region The Government of the Hong Kong Special
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 310S (S31008)/ EN 1.4845 Introduction: SS310 is a highly alloyed austenitic stainless steel designed for elevated-temperature service.
More informationList of approvals of SWG GmbH and GVG mbh
Qualitätsprüfung Produkte Technical Document QP-TQ-TD-01EN Titel: Title: List of approvals of SWG GmbH and GVG mbh Ersetzt: Dokument-Nr.: QP-TQ-TD-01EN Rev.: C vom: 26.01.2015 Replaces: Document-No.: (engl.version)
More informationTARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
More informationPROPERTIES OF MATERIALS
1 PROPERTIES OF MATERIALS 1.1 PROPERTIES OF MATERIALS Different materials possess different properties in varying degree and therefore behave in different ways under given conditions. These properties
More information1501-04-04-03-02:2009 HELLENIC CHNICAL SPECIFICATION. Sanitary ware for disabled persons. ежглеяис тгс йубеямгсеыс (теувос еутеяо) 32199
ежглеяис тгс йубеямгсеыс (теувос еутеяо) 32199 2009-12-23 ICS 93160 1501-04-04-03-022009 H HELLENIC CHNICAL SPECIFICATION Sanitary ware for disabled persons 7 313 111 45 32200 ежглеяис тгс йубеямгсеыс
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet AISI 316 UNS S31600 EN 1.4401 AISI 316L UNS S31630 EN 1.4404 INTRODUCTION NAS provides 316 and 316L SS, which are molybdenum-bearing austenitic
More informationObjectives/Introduction Extraction of zinc Physical properties of zinc Zinc casting alloys Wrought zinc alloys Engineering design with zinc alloys
Lecture 7 Zinc and its alloys Subjects of interest Objectives/Introduction Extraction of zinc Physical properties of zinc Zinc casting alloys Wrought zinc alloys Engineering design with zinc alloys Objectives
More informationFriction Surfacing of Austenitic Stainless Steel on Low Carbon Steel: Studies on the Effects of Traverse Speed
, June 30 - July 2, 2010, London, U.K. Friction Surfacing of Austenitic Stainless Steel on Low Carbon Steel: Studies on the Effects of Traverse Speed H. Khalid Rafi, G. D. Janaki Ram, G. Phanikumar and
More informationThink precision, Think HSS REAMING
Think precision, Think HSS REAMING SUMMARY REAMING TOOLS 2 Zoom on a reamer 3 Which HSS for maximum efficiency? 4 Coatings for the best performance 5 Vocabulary 6 Choose the right design 7 Types of bevel
More informationG1RT-CT-2001-05071 D. EXAMPLES F. GUTIÉRREZ-SOLANA S. CICERO J.A. ALVAREZ R. LACALLE W P 6: TRAINING & EDUCATION
D. EXAMPLES 316 WORKED EXAMPLE I Infinite Plate under fatigue Introduction and Objectives Data Analysis 317 INTRODUCTION AND OBJECTIVES One structural component of big dimensions is subjected to variable
More information