2.5 inch IDE Hard Disk Drive with Legacy-signal PC-HDD/LG User s Guide

Size: px

Start display at page:

Download "2.5 inch IDE Hard Disk Drive with Legacy-signal PC-HDD/LG User s Guide"

Lucas Wilcox
7 years ago
Views:

1 2.5 inch IDE Hard Disk Drive with Legacy-signal PC-HDD/LG User s Guide CONTEC CO.,LTD. Thank you for purchasing the CONTEC PC-HDD/LG. Please use this product in accordance with the procedures described in this document. General Caution - Do not apply pressing force on the top of cover (See Figure 1. on page 2). - Do not cover the breathing hole on the top cover (See Figure 2. on page 2). - Do not touch the interface connector pins and the surface of printed circuit board. - Hard disk are precision instruments. Be extremely careful in handling during and after assembly. - The drive can be easily damaged by shocks or ESD (Electrical Static Discharge), so any damages applied to the drive after taking out from shipping package and opening ESD protective bag are user s responsibilities. - Be sure to turn off the power of the unit when plugging in or unplugging connectors. - Use the mounting screws (M3x5 with sw, w : for screwing the base) provided with the product. Longer screws may damage the interior of the product. - CONTEC bears absolutely no responsibility for use if modified hard disk. - This hard disk drive (HDD) has not guaranteed use by continuation operation and continuation power for 24 hours. When it is used by continuation operation and continuation power a life fails extremely. In the case of a 24-hours operation system, use of our company silicon disk drive (SDD) is recommended. - The life of a hard disk drive changes with environment or operating conditions. As a standard, power time (motor-on time) below 250hours/month (below 8 hours/day), disk access time is 20% or less, it becomes which for 20,000 hours (power time) or five years, or an early thing. 1 PC-HDD/LG

2 Caution of usage DO NOT PRESS! Figure 1. Handling caution of PC-HDD/LG - DO NOT PRESS WHEN YOU TAKE OUT THE DRIVE. - DO NOT PRESS WHEN YOU CARRY THE DRIVE. - ATTACH THE DRIVE FREE FROM PRESSING FORCE. DO NOT COVER THIS HOLE Figure 2. Breathing hole caution of PC-HDD/LG COVERING THIS HOLE WILL RESULT LOSS OF DATA. Absolutely No Impact! Excessive impact (greater than 900G;1ms or 120G;11ms), if this hard disk is subjected to, might cause a fatal error that is not recoverable. When transporting, avoid leaving the disk in the equipment. Instead, use the box the product came in. An impact of 100G is equivalent to the impact when dropped from a height of about 1cm. Unaccommodated host PCs You can not use this drive when if you use these host PCs. IPC-PT/M30(PC), IPC-PE/M30(PC), IPC-PS/M30(PC), IPC-PL/M30(PC), IPC-BX/M20(PC), IPC-BX/M10(PC), PC-386(PC), PC-386(PC)S, PC-486M(PC), IPC-PT/M140(PC), IPC-PS/M140(PC), IPC-PT/M100(PC), IPC-PS/M100(PC), PC-IDE/FD(98)A, PC-486M(PC)H, IPC-PT/M340(PC)H, IPC-PT/M500S(PC), IPC-PT/M530(PC), IPC-PT/M530S(PC),IPC-TT/M300(PC), IPC-TT/M310(PC), IPC-TT/M340(PC),IPC-TT/M340S(PC), IPC-TT/M500(PC), IPC-TT/M500S(PC),IPC-PT/M140(PC), IPC-BX/M400(PC), IPC-BX/P400(PC) PC-HDD/LG 2

3 Capacity is restricted host PCs You can use only 8Gbyte when if you use these host PCs. IPC-PT/M140(PC)H*1, IPC-BX/M400(PC)H*1, IPC-PT/M500(PC) *1: BIOS of Ver and up is required. If you need, please download from Product Configuration Note! - Hard Disk Drive 1 - Screw (M3x5, with sw, w) 4 - Insulation Film 1 - Jumper 1 Check the contents to make sure that you have everything listed above. If you don t have all the items, Please contact CONTEC. External Dimensions ± ± ± M ± ±0.25 3± ± ±0.25 [mm] 9.5 ±0.2 Figure 3. External Dimension 3 PC-HDD/LG

4 Master/Slave Settings C A C A C 4 2 DB A D B Master Setting (Open : Default Setting) Figure 4. D B Slave Setting A-B Short Master/Slave Settings External Dimension Note! Specifications differ slightly depending on the drive manufacturer. Sometimes two drives from two different manufacturers will not operate together. PC-HDD/LG (mfd. by Fujitsu,MHT2020AC) Installation Screw (with sw,w) Installation Part HDD Figure 5. Insulation Film Installation PC-HDD/LG 4

5 Mounting orientation The drive will operate in all axes(six directions). Horizontal Orientation 1 Horizontal Orientation 2 The gravity direction Vertical Orientation 1 Vertical Orientation 2 The gravity direction The gravity direction Vertical Orientation 3 Vertical Orientation 4 5 PC-HDD/LG

6 Hard Ware Specifications Item Specification Format Capacity 20Gbyte Bus Specification AT Interface conforming ATA/ATAPI-6 Transfer Speed (Max.) 100MB/sec (Ultra DMA 100) Nominal Supply/Tolerance +5VDC/±5% Consumed Current Spin up (motor on) 7.0W(RMS Typ.) Read/Write 2.1W(RMS Typ.) Idle 0.9W(RMS Typ.) Operating Conditions Temperature 5 C to 55 C (Ambient) 5 C to 60 C (Surface) Humidity 8% to 90%RH (With no condensation) Maximum Wet Bulb 29 C(With no condensation) Temperature Maximum Temperature Gradient 20 C/Hour Altitude -300m to 3000m Vibration (Swept sine, 1/4 octave per minute) 1G 0-peak, 5 to 500Hz Shock (Half-sine pulse) 225G 0-peak, 2ms Nonoperating Conditions Temperature -40 C to 65 C Humidity 5% to 95%RH (With no condensation) Maximum Wet Bulb Temperature 40 C(With no condensation) Maximum Temperature Gradient 20 C/Hour Altitude -300m to 12000m Vibration 5G 0-peak, 5 to 500Hz (Swept sine, 1/4 octave per minute) Shock 900G 0-peak, 1ms 120G 0-peak, 11ms Weight 99g PC-HDD/LG 6

7 Connector Pin Assignment Pin Signal Function I/O Pin Signal Function I/O 1 RESET- Bus Reset I 2 GND Signal Ground 3 DB7 Data Bus Bit 7 I/O 4 DB8 Data Bus Bit 8 I/O 5 DB6 Data Bus Bit 6 I/O 6 DB9 Data Bus Bit 9 I/O 7 DB5 Data Bus Bit 5 I/O 8 DB10 Data Bus Bit 10 I/O 9 DB4 Data Bus Bit 4 I/O 10 DB11 Data Bus Bit 11 I/O 11 DB3 Data Bus Bit 3 I/O 12 DB12 Data Bus Bit 12 I/O 13 DB2 Data Bus Bit 2 I/O 14 DB13 Data Bus Bit 13 I/O 15 DB1 Data Bus Bit 1 I/O 16 DB14 Data Bus Bit 14 I/O 17 DB0 Data Bus Bit 0 I/O 18 DB15 Data Bus Bit 15 I/O 19 GND Signal Ground I/O 20 KEY Key Pin 21 Open 22 GND Signal Ground 23 IOW- Host I/O Write I 24 GND Signal Ground 25 IOR- Host I/O Read I 26 GND Signal Ground 27 IORDY I/O ch RDY O 28 Reserved 29 Reserved 30 GND Signal Ground 31 INTRQ Interrupt Request O 32 IOCS16- Drive 16 Bit I/O O 33 ADD1 Host Address 1 I 34 PDIAG- Passed Diagnostic I/O 35 ADD0 Host Address 0 I 36 ADD2 Host Address 2 I 37 CSO- Chip Select 0 I 38 CS1- Chip Select 1 I 39 DASP- Active (LED) O 40 GND +5V Return 41 +5V +5VDC 42 +5V +5VDC 43 GND +5V Return 44 Reserved Drive Characteristics (Logical Drive Format) Description Logical Head Number Logical Sector /Track Logical Cylinder Number Logical Sector Size Number of Sectors Total logical data Bytes PC-HDD/LG , ,070,080 20,003,880,960 Copyright Copyright 2003 CONTEC CO., LTD. ALL RIGHTS RESERVE No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD. CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD. Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this document nor for results obtained by the user as a result of using this product. 7 PC-HDD/LG

8 Limited One-Year Warranty CONTEC Interface boards are warranted by CONTEC to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser. Replacement or repair will be free of charge only when this device is returned to CONTEC freight prepaid with the original invoice. This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and original boards. The warranty is not applicable if the device has been tampered with or damaged through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in which case repairs will be considered beyond the warranty policy. If replacement with a new device is needed, regular factory prices will be charged, the product will be returned to you COD, and no other written warranty will apply. The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage, misuse, or malfunction of this device. How to Obtain Service For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please obtain a Return Merchandise Authorization Number (RMA) from our Sales Administration Department before returning any product. No product will be accepted without an RMA number. Copyright 2003 CONTEC CO., LTD. CONTEC CO., LTD. ALL RIGHTS RESERVED. December 2004 Edition , Himesato, Nishiyodogawa-ku, Osaka , Japan Japanese English A (LYCY311) Chinese _rev2 [ ] No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD.

PRODUCT MANUAL. Barracuda 7200.10 Serial ATA ST3750640AS ST3750840AS ST3500630AS ST3500830AS ST3400620AS ST3400820AS ST3320620AS ST3320820AS

PRODUCT MANUAL. Barracuda 7200.10 Serial ATA ST3750640AS ST3750840AS ST3500630AS ST3500830AS ST3400620AS ST3400820AS ST3320620AS ST3320820AS PRODUCT MANUAL Barracuda 7200.10 Serial ATA ST3750640AS ST3750840AS ST3500630AS ST3500830AS ST3400620AS ST3400820AS ST3320620AS ST3320820AS ST3300620AS ST3300820AS ST3250620AS ST3250820AS ST3250410AS ST3250310AS