Contact numbers: Telephone +44 (0) Fax +44 (0) Web site

Transcription

1 2014 PRODUCT GUIDE

2 Range Page Flexo Inks - Low Migratory 3 Information on Heat Stable inks & L.M. Flexo Blacks 4 Information L.M. Flexo Whites 5 Flexo Inks Lightfast 6 Flexo Inks - Ultra Low Migratory 7 Information on Ultra L.M. Flexo Whites & Flexo Blacks 8 Flexo Inks - Altus 9 Flexo Metallics & Scratch -Off 10 Flexo Fluorescents 11 Flexo Additives 12 Letterpress Inks - Low Migratory 13 Letterpress Inks Low Migratory Lightfast 14 Letterpress Metallics & Scratch-Off 15 Letterpress Fluorescents 16 Letterpress Additives 17 Waterbased 4000 Series 18 Waterbased 8000 Series 19 Waterbased Additives 20 L.M. Flexo Clearcoat Selector and Special Coatings Guide 21 L.M. Letterpress Clearcoat Selector and Special Coatings Guide 22 Contact numbers: Telephone +44 (0) Fax +44 (0) info@paragoninks.co.uk Web site Please note that this is not an exhaustive list of the products in our range. If you need something that is not listed here please call us to discuss your requirements. This guide is produced annually and is representative of our most up to date products at the time of publishing. 2

3 UVDRY FLEXO LOW MIGRATORY (L.M.) RANGE Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) 4 Colour Process Set Standard Strong L.M. PANTONE Process Yellow LMYF9803 LMYF9905 L.M. PANTONE Process Magenta LMRF9805 LMRF9905 L.M. PANTONE Process Cyan LMCF9805 LMCF9905 L.M. PANTONE Process Black LMBF9807 LMBF9907 Base Colours L.M. PANTONE Yellow LMYF9801 L.M. Mixing Orange LMYF9802 L.M. PANTONE 021 Orange LMYF9804 L.M. PANTONE Warm Red LMRF9802 L.M. PANTONE 032 Red LMRF9804 L.M. PANTONE Rubine LMRF9801 L.M. PANTONE Rhodamine LMRF9803 L.M. PANTONE Purple LMCF9803 L.M. PANTONE Violet LMVF9801 L.M. PANTONE 072 Blue LMCF9804 L.M. PANTONE Reflex Blue LMCF9802 L.M. PANTONE Process Blue LMCF9801 L.M. PANTONE Green LMGF9801 L.M. PANTONE Mixing / Untoned Black LMBF9802 L.M. Tinting Meduim LMTF9801 L.M. Opaque White LMWF9801 L.M. Spot Reflex Blue L.M. Spot 032 Red USE LMCF9804 LMRF9814 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) Flexo L.M. Gloss Lacquer General Purpose Flexo L.M. Gloss Lacquer Overprintable L512 L508 3

4 UVDRY FLEXO LOW MIGRATORY (L.M.) RANGE Additional Inks for Oven / Heat applications Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) Base Colours L.M. Special Yellow (Oven) L.M. Special Mixing Orange L.M. Special 021 Orange L.M. Special Warm Red L.M. Special 032 Red Y4570 Y4560 Y4565 R4358 R4357 Additional Information on Flexo Blacks Description Recommendations Designed for use in colour matchings. It can also be L.M. Mixing / LMBF9802 used as a spot black but will be a browner, less blue Untoned Black finish than the Jobbing or Dense Black. Recommend aniloxes up to a volume of 9.0cm 3 /m 2. Designed as a standard black for process. Not to be L.M. Process LMBF9807 used for solids at heavy volumes as cure is affected. Black Recommend anilox volumes of cm 3 /m 2. Designed as a strong black for process. Not to be L.M. Strong LMBF9907 used for solids at heavy volumes as cure is affected. Process Black Recommend anilox volumes of cm 3 /m 2. Designed as a standard black for process or solid L.M. Process / black printing. Can be used for solids at heavier Jobbing Black LMBF9817 volumes. Recommend aniloxes up to a volume of 9.0cm 3 /m 2. 4

5 Additional Information on Flexo Whites Description L.M. Opaque White L.M. High Performance Opaque White Flexo Dense White Shrink Sleeve Backing White For Hot Melt Application Flexo Sleeve Backing White L.M Special Opaque White for Lidding Applications Recommendations Designed for use in colour matchings. Can also be LMWF9801 used as a first down white where a dense opaque white is not required. Recommended anilox volume of cm 3 /m 2. Designed to offer a maximum opacity first down white. Ideal for high speed printing for a clear on W404 clear screen look white. Printing recommendations; Tape - hard, Plate analogue or digital, aniloxes up to a volume of 30cm 3 /m 2. Designed to offer a maximum opacity first down white for shrink sleeve application. Also suitable W301 for use in colour matchings. Printing recommendations for floodcoat of white; Tape - hard, Plate analogue or digital, aniloxes up to a volume of 20cm 3 /m 2. Designed as a backing white for shrink sleeve application. Only for application where a glue is used to hold W307 the sleeve to the container. This product is not overprintable. Recommended anilox volumes of 8-10cm 3 /m 2. Designed as a backing white for shrink sleeve application only. This ink offers good opacity, W305 shrinkability and slip for sleeve packaging. This product is not overprintable. Recommended anilox volumes of 8-10cm 3 /m 2. Designed to offer a maximum opacity first down white for aluminium lidding. Recommended anilox W320 volumes of 8-15cm 3 /m 2. 5

6 UV FLEXO L.M. LIGHTFAST INKS Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) 4 Colour Process Set L.M. PANTONE Process Yellow LMYF7603 L.M. Lightfast Process Magenta / Rubine LMR4095 L.M. PANTONE Process Cyan LMCF7605 L.M. PANTONE Process Black LMBF9805 Base Colours L.M. PANTONE Yellow LMYF9801 L.M. Mixing Orange LMYF9802 L.M. Lightfast 021 Orange LMY1961 L.M. Lightfast Warm Red LMR3679 L.M. Lightfast 032 Red LMR3624 L.M. Lightfast Process Magenta / Rubine LMR4095 L.M. Lightfast Rhodamine LMR1959 L.M. PANTONE Purple LMCF9803 L.M. Lightfast Violet LMC3082 L.M. Lightfast 072 Blue LMC4238 L.M. Lightfast Reflex Blue LMC4765 L.M. PANTONE Process Blue LMCF7201 L.M. PANTONE Green LMGF9801 L.M. PANTONE Mixing / Untoned Black LMBF9802 L.M. Tinting Meduim LMTF9801 L.M. Opaque White LMWF9801 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) Flexo L.M. Gloss Lacquer General Purpose Flexo L.M. Gloss Lacquer Overprintable L512 L508 6

7 UV FLEXO ULTRA L.M. INKS Complies with EuPIA migration limits of 10ppb (Benzophenone, ITX and BDK free) 4 Colour Process Set Standard Strong Ultra L.M. PANTONE Process Yellow ULMYF6803 ULMYF6905 Ultra L.M. PANTONE Process Magenta ULMRF6805 ULMRF6905 Ultra L.M. PANTONE Process Cyan ULMCF6805 ULMCF6905 Ultra L.M. PANTONE Process Black ULMBF6807 ULMBF6907 Base Colours Ultra L.M. PANTONE Yellow ULMYF6801 Ultra L.M. Mixing Orange ULMYF6802 Ultra L.M. PANTONE 021 Orange ULMYF6804 Ultra L.M. PANTONE Warm Red ULMRF6802 Ultra L.M. PANTONE 032 Red ULMRF6804 Ultra L.M. PANTONE Rubine ULMRF6801 Ultra L.M. PANTONE Rhodamine ULMRF6803 Ultra L.M. PANTONE Purple ULMCF6803 Ultra L.M. PANTONE Violet ULMVF6801 Ultra L.M. PANTONE 072 Blue ULMCF6804 Ultra L.M. PANTONE Reflex Blue ULMCF6802 Ultra L.M. PANTONE Process Blue ULMCF6801 Ultra L.M. PANTONE Green ULMGF6801 Ultra L.M. PANTONE Mixing / Untoned Black ULMBF6802 Ultra L.M. Tinting Meduim ULMTF6801 Ultra L.M. Opaque White ULMWF6801 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) Ultra L.M. Gloss Lacquer General Purpose Ultra L.M. Gloss Lacquer Overprintable ULML912 ULML908 7

8 Additional Information on Flexo Blacks Description Recommendations Ultra L.M. Mixing / Untoned Black Ultra L.M. Process Black Ultra L.M. Strong Process Black Ultra L.M. Process / Jobbing Black ULMBF6802 ULMBF6807 ULMBF6907 ULMBF6817 Designed for use in colour matchings. It can also be used as a spot black but will be a browner, less blue finish than the Jobbing or Dense Black. Recommend aniloxes up to a volume of 9.0cm 3 /m 2. Designed as a standard black for process. Not to be used for solids at heavy volumes as cure is affected. Recommend anilox volumes of cm 3 /m 2. Designed as a strong black for process. Not to be used for solids at heavy volumes as cure is affected. Recommend anilox volumes of cm 3 /m 2. Designed as a standard black for process or jobbing black for printing solids. Can be used for solids at heavier volumes. Recommend anilox volumes of cm 3 /m 2. Additional Information on Flexo Whites Description Recommendations Ultra L.M. Opaque White ULMWF6801 Ultra L.M. High Performance Opaque White Ultra L.M. Flexo Dense Opaque White Ultra L.M. Shrink Sleeve Backing White For Hot Melt Application Ultra L.M.Flexo Sleeve Backing White Ultra L.M Special Opaque White for Lidding Applications ULMW604 ULMW601 ULMW607 ULMW605 ULMW620 Designed for use in colour matchings. Can also be used as a first down white where a dense opaque white is not required. Recommended anilox volumes of cm 3 /m 2. Designed to offer a maximum opacity first down white. Ideal for high speed printing for a clear on clear screen look white. Printing recommendations; Tape - hard, Plate analogue or digital, anilox volumes of 20-30cm 3 /m 2. Designed to offer a maximum opacity first down white for shrink sleeve application. Also suitable for use in colour matchings. Printing recommendations for floodcoat of white; Tape - hard, Plate analogue or digital, aniloxes up to a volumes of 15-20cm 3 /m 2. Designed as a backing white for shrink sleeve application. Only for application where a glue is used to hold the sleeve to the container. This product is not overprintable. Recommended volumes of 8-10cm 3 /m 2. Designed as a backing white for shrink sleeve application only. This ink offers good opacity, shrinkability and slip for sleeve packaging. This product is not overprintable. Recommended volume of 8-10cm 3 /m 2. Designed to offer a maximum opacity first down white for aluminium lidding. Recommended anilox volumes of 8-15cm 3 /m 2. 8

9 UV FLEXO L.M. ALTUS INKS Bespoke ink range designed for high srink rate, shrink sleeve materials Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) 4 Colour Process Set Strong Altus Strong Process Yellow ALYF9905 Altus Strong Process Magenta ALRF9905 Altus Strong Process Cyan ALCF9905 Altus Strong Process Black ALBF9901 Base Colours Altus Strong Process Yellow Altus Mixing Orange Altus 021 Orange Altus Warm Red Altus 032 Red Altus Strong Process Magenta Altus Rhodamine Altus Purple Altus Violet Altus 072 Blue Altus Strong Process Cyan Altus Green Altus Mixing / Untoned Black L.M. Tinting Medium L.M. Opaque White Sleeve Backing White Sleeve Backing White for Hot Melt Dense Opaque White ALYF9905 ALYF9802 ALYF9804 ALRF9802 ALRF9804 ALRF9905 ALRF9803 ALCF9803 ALVF9801 ALCF9804 ALCF9905 ALGF9801 ALBF9802 LMTF9801 LMWF9801 W305 W307 W301 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. 9

10 UV FLEXO INKS - SPECIALS 1 - Pack Metallics Flexo 1-Pack 871c Gold 1941 Flexo 1 Pack 872c Gold 1927 Flexo 1-Pack 873c Gold 1928 Flexo 1-Pack 874c Gold 1929 Flexo 1-Pack 875c Gold 1930 Flexo 1-Pack 876c Gold 1931 Flexo New 1-Pack 877c Silver 1958 Flexo 1-Pack 877c Silver 1960 Flexo 1-Pack 877c Silver (Low Viscosity) 1950 Flexo 1-Pack Bright Silver 1945 Shelf Life: 6 months Scratch-Off Metallic System Flexo Scratch-off Base Lacquer L501 Flexo Scratch-off Metallic Varnish MV830 Flexo New Silver Paste 1957 Flexo Rich Gold Paste 1823 Flexo Dense Scratch-off Black B1828 Flexo Scratch-off Overlacquer L574 Unmixed Shelf Life: 6 months. Mixed Shelf Life: 24 hours Contact Paragon for the Product Information Sheet which contains technical information and printing recommendations. 10

11 UV FLEXO INKS - SPECIALS Fluorescent Fluorescent 801c Blue Fluorescent 802c Green Fluorescent 803c Yellow Fluorescent 804c Orange Fluorescent 805c Red Fluorescent 806c Pink Fluorescent 807c Purple Fluorescent 808c Green Fluorescent 809c Yellow Fluorescent 810c Orange Fluorescent 811c Orange Fluorescent 812c Red Fluorescent 813c Pink Fluorescent 814c Purple C3414 G1916 Y4315 Y2116 R2579 R3715 C3661 G2585 Y3733 Y2935 Y2936 R2589 R3759 C3290 Printing Fluorescents Fluorescent pigments are, in general, very weak in colour strength compared to conventional inks and certain colours may require a heavy film weight of ink or 2 hits at a lighter film weight to achieve the desired colour and cure. Fluorescent Lightfastness Fluorescent colours are, with the exception of the 801c Blue, very poor for lightfastness and are estimated at Blue wool Scale 1-2. We do not recommend that the printed examples of these colours be exposed to daylight conditions. Contact Paragon for the Product Information Sheet, which contains further technical information and printing recommendations 11

12 UV FLEXO ADDITIVES Description Liquid Reducer (L.M, Altus & ULM) Cure Promoter L.M. & Altus (Colours only) Cure Promoter (Non L.M. & ULM) Slip Additive (L.M, Altus & ULM) Levelling Additive (L.M, Altus & ULM) Details AD105 Use as required to lower the viscosity and tack of inks and varnishes. Use to a maximum of 10%. AD220 Used to improve the cure of coloured inks. Do not use in clear coatings, whites or tints. An add of 2-3% should be sufficient. AD202 Use at 2-3% to improve the cure of whites. Can also be used in clear coatings. AD317 Used to improve the tape adhesion of inks or varnishes. Do not use in systems intended for foil blocking, overprinting or gluing. An add of % should be sufficient. Add to subsequent colours used in the process for trapping purposes. AD325 Used to improve the lay of one ink on top of another. Can be used to improve lay of the ink on difficult substrates. Do not use in systems intended for foil blocking, overprinting or gluing. An add of % should be sufficient. 12

13 UV LETTERPRESS LOW MIGRATORY (L.M.) INKS Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) 4 Colour Process Set L.M. PANTONE Process Yellow LMYP2003 L.M. PANTONE Process Magenta LMRP2005 L.M. PANTONE Process Cyan LMCP2005 L.M. PANTONE Process Black LMBP2001 Base Colours L.M. PANTONE Yellow L.M. PANTONE 021 Orange L.M. PANTONE Warm Red L.M. PANTONE 032 Red L.M. PANTONE Rubine L.M. PANTONE Rhodamine L.M. PANTONE Purple L.M. PANTONE Violet L.M. PANTONE 072 Blue L.M. PANTONE Reflex Blue L.M. PANTONE Process Blue L.M. PANTONE Green L.M. PANTONE Mixing / Untoned Black L.M. Tinting Medium L.M. Opaque White LMYP2001 LMYP2002 LMRP2002 LMRP2004 LMRP2001 LMRP2003 LMCP2003 LMCV2001 LMCP2004 LMCP2002 LMCP2001 LMGP2001 LMBP2002 LMV2001 LMW2001 L.M. Dense Opaque White LMW095 L.M. Spot Reflex Blue (Fine text & line work) LMC3003 L.M. Process / Dense Black (Fine text & line work) ULMB1450 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) Flexo L.M. Gloss Lacquer General Purpose Flexo L.M. Gloss Lacquer Overprintable L512 L508 13

14 UV LETTERPRESS (L.M.) LIGHTFAST INKS Complies to global migration limits of 60ppm (Benzophenone, ITX and BDK free) 4 Colour Process Set Process Yellow LMYP3003 Process Magenta LMRP3005 Process Cyan LMCP3005 Process Black LMBP3001 Base Colours Yellow LMYP Orange LMYP3002 Warm Red LMRP Red LMRP3004 Rubine LMRP3001 Rhodamine LMRP3003 Purple LMCP3003 Violet LMCV Blue LMCP3004 Reflex Blue LMCP3002 Process Blue LMCP3001 Green LMGP3001 Mixing / Untoned Black LMBP3002 Tinting Medium LMV3001 Opaque White LMW3001 L.M. Dense Opaque White LMW095 Contact Paragon for the Product Information Sheet which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) Flexo L.M. Gloss Lacquer General Purpose Flexo L.M. Gloss Lacquer Overprintable L512 L508 14

15 UV LETTERPRESS INKS SPECIALS 1 - Pack Metallics Letterpress 1-Pack 871c Gold 1991 Letterpress 1-Pack 872c Gold 1992 Letterpress 1-Pack 873c Gold 1993 Letterpress 1-Pack 874c Gold 1994 Letterpress 1-Pack 875c Gold 1995 Letterpress 1-Pack 876c Gold 1996 Letterpress 1-Pack 877c Silver 1997 Shelf Life: 6 months Letterpress Scratch-Off Letterpress Scratch-Off Duct Varnish V234 Letterpress Scratch-Off Metallic Varnish MV1051 Letterpress Silver Paste 1964 Letterpress Rich Gold Paste 1811 Letterpress Scratch-Off Black B1228 Flexo New Scratch-Off Over Lacquer L574 Unmixed Shelf Life: 6 months. Mixed Shelf Life: maximum 12 hours Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. 15

16 UV LETTERPRESS INKS SPECIALS Fluorescent Fluorescent 801c Blue Fluorescent 802c Green Fluorescent 803c Yellow Fluorescent 804c Orange Fluorescent 805c Red Fluorescent 806c Pink Fluorescent 807c Purple Fluorescent 808c Green Fluorescent 809c Yellow Fluorescent 810c Orange Fluorescent 811c Orange Fluorescent 812c Pink Fluorescent 813c Pink Fluorescent 814c Purple C1511 G844 Y1150 Y1159 R1203 R1204 C1512 G3402 Y1165 Y2150 Y3965 R3811 R3812 C2885 Printing Fluorescents Fluorescent pigments are, in general, very weak in colour strength compared to conventional inks and certain colours may require a heavy film weight of ink or 2 hits at a lighter film weight to achieve the desired colour and cure. Fluorescent Lightfastness Fluorescent colours are, with the exception of the 801c Blue, very poor for lightfastness and are estimated at Blue wool Scale 1-2. We do not recommend that the printed examples of these colours be exposed to daylight conditions. Contact Paragon for the Product Information Sheet, which contains further technical information and printing recommendations 16

17 UV LETTERPRESS ADDITIVES Description Details Liquid Reducer AD101 Use as required to lower the viscosity and tack of inks and varnishes. An add of 5% should be sufficient. Cure Promoter AD200 Use at 2-3% to improve the cure of whites. Can also be used in clear coatings. Cure Promoter L.M. Letterpress & L.M. Primoflo Slip Additive Gel Reducer AD220 Used to improve the cure of coloured inks. Do not use In clear coatings, whites or tints. An add of 2-3% should be sufficient. AD317 Use at 1-2% to improve the tape adhesion of inks or varnishes. Do not use in systems intended for foil blocking, overprinting or gluing. Add to subsequent colours used in the process for trapping purposes. AD103 Special reducer which will lower the tack of an ink or varnish. Ideal for use on flat bed or semi-rotary machines. An add of 5-10% should be sufficient. 17

18 FLEXO WATERBASED 4000 SERIES 4 Colour Process Set Process Yellow WBYF4405 Process Magenta WBRF4405 Process Cyan WBCF4405 Process Black WBBF4407 Base Colours Yellow WBYF Orange WBYF4404 Warm Red WBRF Red WBRF4404 Rubine WBRF4401 Rhodamine WBRF4403 Purple WBCF4403 Violet WBVF Blue WBCF4404 Reflex Blue WBCF4402 Blue WBCF4401 Green WBGF4401 Mixing / Untoned Black WBBF4402 Extender WBTF4401 Opaque White WBWF4404 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) High Slip Lacquer (Non O/P) Trans Process Extender WBC412 WBC408 18

19 FLEXO WATERBASED 8000 SERIES 4 Colour Process Set Process Yellow WBYF8805 Process Magenta WBRF8805 Process Cyan WBCF8805 Process Black WBBF8807 Base Colours Yellow WBYF Orange WBYF8804 Warm Red WBRF Red WBRF8804 Rubine WBRF8801 Rhodamine WBRF8803 Purple WBCF8803 Violet WBVF Blue WBCF8804 Reflex Blue WBCF8802 Blue WBCF8801 Green WBGF8801 Mixing / Untoned Black WBBF8802 Extender WBTF8801 Opaque White WBWF8804 Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Recommended Gloss Lacquer for above inks: (See Clear Coat Selector for more information) High Slip Lacquer (Non O/P) Trans Process Extender WBC412 WBC408 19

20 WATERBASED ADDITIVES Description Details Retarder AD2401 Additive to reduce drying times. Add up to 5%. Fast Solvent Refresh Stabilizer Reducer Levelling Additive Print Clean Stabiliser Press Side Defoamer AD2402 Additive to increase drying times. Add up to 10%. Must be stirred in. AD2414 Keeps inks open on long runs. An add of 2-3% should be sufficient. AD2415 Silicone additive, reduces pinholes, etc. Add up to 2%. Must be stirred in. AD2405 Best all round additive for ph, reduced drying and stability. Add up to 10%. AD2416 Defoamer additive. Add up to 3% 20

21 L.M. and ULTRA L.M. FLEXO CLEARCOAT SELECTOR GUIDE (Benzophenone, ITX and BDK free) Key Feature Finish Paper Filmic Chemi Thermal Blocking Scuff resistant L.M. ULM Gloss L512 ULML912 General Purpose Satin L520 ULML920 Matt L516 ULML916 Gloss L508 ULML908 Thermal Transfer / Satin L513 ULML913 Foil Blocking Matt L519 ULML919 Primer Gloss L523 ULML923 Primer - Difficult ULML968 Gloss L568 Substrates Direct Thermal Gloss L514 ULML914 Matt L530 ULML930 Superior Slip / Rub / Water Resistance Gloss L544 ULML944 Matt L506 ULML906 Recommended Testing advised Not recommended FLEXO SPECIAL COATINGS GUIDE Key Features Type ULM Finish Low Curl. Offers minimal shrinkage resulting in low curl. Gloss L596 ULML982 IML Designed for perfect IML application Gloss L576 ULML976 Adhesive Deadener. Removes tack when printed onto permanent Gloss L301 ULML949 acrylic based adhesives. Blue UVA Gloss L566 Laminating Adhesive. Bonds clear film to paper and filmic Free Radical L392 materials. Cationic L507 N/A Cold Foil Adhesive. Bonds decorative foil to any substrate. L414 High Visco L533 Release Coating. Wet Peel, used for coupon and reseal products. Cationic Gloss L075 N/A Cationic Matt L336 N/A Signature Panel. Accepts ball point pen with minimal smudging. Matt L521 Special Textured. Leaves a rough textured finish. Matt L570 Soft Touch. Leaves a silky, soft touch finish. Matt L432 HMRC Duty Stamps. Security coating required for UK Duty Stamps. Yellow UVA Gloss L464 Optically Bright Coatings Used for trigger marking / security applications. These coatings fluoresce under UV black light. Special Effect. These coatings provide a silver glitter or pearlescent effect. Interference Coatings. These coatings can be used for security applications or special effects. Other colours are available on request. 21 Yellow UVA Gloss L463 Blue UVA Gloss L405 Blue UVA O/P Gloss L372 Blue UVA Matt L328 Glitter L229 Pearl L222 Yellow L319 Blue L455 Lilac L398 Red L318 Green Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. L456

22 L.M. LETTERPRESS CLEARCOAT SELECTOR GUIDE (Benzophenone, ITX and BDK free) Key Feature Finish Paper Filmic Chemi Thermal Blocking Scuff resistant L.M. Gloss V540 General Purpose Satin V573 Matt V595 Thermal Transfer / Foil Blocking Gloss V510 Satin V564 Matt V525 Cost Effective Gloss V524 Primer Gloss V521 Direct Thermal Gloss V575 Superior Matt Matt V536 Recommended Testing advised Not recommended LETTERPRESS SPECIAL COATINGS GUIDE Key Features Type Finish Adhesive deadener. Removes tack when printed onto permanent acrylic based Gloss V076 adhesives. Cold Foil Adhesive. Bonds decorative foil to any substrate. V330 Release Coating. Wet peel, used for coupon and reseal products. Cationic V220 Release Coating. Dry Peel, used for coupon and reseal products. V033 Signature panel. Accepts ball point pen with minimal smudging. Matt V525 HMRC Duty Stamps. Security coating required for UK Duty Yellow UVA Stamps. Gloss V335 Optically Bright Coatings Yellow UVA Gloss V341 Used for trigger marking / security applications. These coatings Blue UVA fluoresce under UV black light. overprintable Gloss V043 Special effect. Glitter V122 These coatings provide a silver glitter or pearlescent effect. Pearl V031 Interference Coatings. These coatings can be used for security applications or special effects. Yellow V285 Red V312 Other colours are available on request. Contact Paragon for the Product Information Sheet, which contains technical information and printing recommendations. Other Specials available on request. Glow in the dark or Thermochromics, etc. Issued 7 6 th January