AO-1210 LAN to ZigBee Converter Quick User Manual

Transcription

1 AO-1210 Converter Quick User Manual

2 1. Introduction AO-1210 is an embedded Internet/Ethernet controller suitable for embedded wireless control applications. This converter can perform conversion from Addressable Ethernet to ZigBee 2007 Pro standard. Most ZigBee devices do not support device addresses over the Internet. The AO-1210 can assign a static IP or dynamic IP address from the DHCP sever to any ZigBee device installed in the Ethernet network. Characteristically, AO-1210 is a transparent device which does not require any extra header field appended to transmitted data. For example, when Host-PC sends data to the destination AO-1210 via Ethernet network, the ZigBee interface of AO-1210 will receive the same data. 2. Wiring There are 2 approaches to connect AO-1210 and the host PC. 1. Use the Cross Over CAT-5 cable to link AO-1210 and the Host PC directly, as shown below. Host PC CAT-5 Cross Over AO Connect AO-1210 and the Host PC though an Ethernet HUB, as shown below. Ethernet HUB AO-1503#1 Host PC AO-1210 (Repearter) AO-1210 (Repearter) AO-1503#2 AO-1503#3 Page 1 of 5

3 3. Quick Start 3.1 LAN Settings AO-1210 has a built-in web server, users can change all internal parameter setting by browser interface. The default IP address is To set the parameters, users can use any browser and open the URL ( These parameters include serial and network settings as illustrated in the following figure. When the parameter setting is completed, just press the Apply button, then new parameters will be saved and the AO-1210 will reboot. Page 2 of 5 The main page provides two essential functions, (1) Apply: to update all parameters. (2) Reset: to reset the configuration value to the default settings produced by the manufacturer. Notice: Don t press the Firmware Update button.

4 3.2 ZigBee Settings (New) (1) Format Representation: note that commands are all uppercase ASCII code. ///x NNNN PPPP ChPo (2) Description: ///x ///: Start command, x = R set to ROUTER, x = C set to Coordinator NNNN: Node ID, ex: 1234 (i.e., 0x1234) Router: range from 0001 to EFFF (Hex representation) Coordinator: fixed to 0000 (Hex representation) PPPP: PAN ID, range 0000 to EFFF (Hex representation) ChPo: set channel and output power Ch: range from 11 to 26 (Dec representation) Po: range from 0 to 16 (Dec representation) Value OutPower Value OutPower Value OutPower Value OutPower dBm dbm 08-8 dbm dbm dbm 05-3 dbm dbm dbm 02 1 dbm 06-4 dbm dbm dbm dbm 07-6 dbm dbm dbm (3) Examples: ///R Router, NID=0001, PID=0020, 26 channel, TX output power 4.5dBm. ///C Coordinator, NID=0000, PID=0020, 26 channel, TX output power 4.5dBm. Query command: ///? HOST sends ///? to query AO-1210 ZigBee setting status AO-1210 responses ///xnnnnppppchpo (refer to (2) format description) Page 3 of 5 Send command: received unspecified NID, i.e., data broadcast mode specify received NID Format :NNNNddddddd (at most 60 bytes) Ex :0243hallo_world!

5 Assign NODE ID=0x0243 Route to receive data hallo_world! 3.3 ZigBee Settings (AT command): please refer to AO-1503 user manual. 4. Hardware Features Serial Interface Interface: UART compatibility. Data Rate: 9600 bps. Characters: 8. Parity: None Stop Bits: 1. Ethernet Interface Ethernet Interface: 10Base-T, 100Base-TX. Ethernet Speed/Duplex: Auto-negotiation 10/100Mbps, Full/Half duplex. Protocols Supported: ARP, IP, UDP, TCP, BootP. Network Services: DHCP, DNS, PPPoE, TFTP, HTTP, UDP Broadcasting. Auto-MDIX: Yes. Electronic Character DC Power Consumption: DV5V /350mA(max). Operation Temperature: 0~65. Operation Humidity: 0~85%RH. Storage Temperature: -20~85. Page 4 of 5