EMG Ethernet Modbus Gateway User Manual

Size: px
Start display at page:

Download "EMG Ethernet Modbus Gateway User Manual"

Transcription

1 EMG Ethernet Modbus Gateway User Manual Rev /2010

2 CONTENTS 1. Introduction 1.1. General Features 1.2 Installing the Drivers 2. Configuration 2.1 Main Device Parameters RS485 Serial Communication Parameters Baud Rate Data Bit Stop Bit Parity Bit Time-Out Delay Network Parameters Connection Settings DHCP WEB Access WEB Port Log-in Timeout Server IP IP Address Subnet Mask Default Gateway MODBUS/TCP Port Link Operating Modes (MODBUS/TCP /Tunnel Mode) MODBUS/TCP Packet Structure Tunnel Mode Packet Structure Configuration example for communicating over ADSL modem 2.1 Reading/Changing the Configuration using the USB interface 2.2 Security settings 2.3 Reading/Changing the Configuration using the WEB interface

3 3. Firmware Updates 4. Appendices Appendix A Differences between EMG model devices Appendix B Query Interval and TCP Time-Out

4 1.Introduction 1.1 General Features ENTES EMG family series MODBUS Gateway is a MODBUS/TCP protocol converter that lets the users control their devices remotely through serial connection via the RS-485 protocol using TCP/IP protocol over the existing internet/intranet infrastructure. While it is possible to monitor from one place with EMG-10, it is possible to monitor from 4 different places with EMG-02 and EMG-12. Technical Data : Category Description Network Protocols Serial Ports Operating Modes Network Interface Serial Communication Formats Serial Interface Power Supply Insulation and Protection TCP/IP, ARP, ICMP, HTTP, ModbusTCP RS485 for Communication, USB Port for Configuration ModbusTCP/RTU and Modbus Tunnel 10/100 Mbps auto-negotiation Data Bits : data bit Stop Bit: characters Parity: Even-Odd-None bps 9-24V AC V DC or from USB port(~75 ma) RS485 port: 500V Ethernet port: 1500V 15KV ESD protection on USB port 10/1000 us (600W) transient pulse protection on RS485 port Table 1. EMG Series Technical Data

5 1.2 Installing the drivers Since the EMG series devices communicate through the computer USB port, the drivers which come with the bundled CD must be installed to the computer before using the device. To install the drivers; 1. Connect the EMG series device to the computers through the USB port of computer. The POWER LED on the device should turn on and the computer will recognize the device automatically. 2. To locate the driver files manually, select Install from a list or specific location option and click on Next. 3. On the next window, specify the location of the drivers and click on Next.

6 4. Click on Continue on the next window 5. The system will copy the necessary files to the computer. 6. Copying progress is finished and the EMG Series device is now ready to use. 7. After the installation is completed, the device can be seen using these steps: My Computer Control Panel System Device Manager Universal Serial Bus Controller

7 2. Configuration 2.1 Main Device Parameters In order for the device to function properly, both the RS-485 serial communication parameters and the network parameters have to be configured correctly. Incorrect or incomplete configuration of these parameters can degrade the system performance and even disrupt the existing network infrastructure. Network Settings Connection Server Setting DHCP Off WEB Access Off Log-in Timeout ms Link Auto IP Address Gateway Address Subnet Mask Port 502 MODBUS/TC Operating Mode P Serial Port Settings Baud Rate 9600 Data Bit Stop Bit Parity Timeout Delay 8 1 None 2000 ms 50 ms Table 2. EMG Factory Default Values

8 2.1.1 RS485 Serial Communication Parameters EMG Series device uses these parameters along with other units to which the device is serially connected. For high performance communication, all the device parameters over an RS-485 network must be configured the same Baud Rate Defines the communication speed of the device. Supported rates are: 1200, 2400, 4800, 9600, 19200, 38400, 57600, bps Data Bit Defines the data packet size. Supported bit values are: 5, 6, 7, Stop Bit Stop bits come after the data and parity bits in serial communication protocols and indicate that the data packet has ended. Supported stop bit values are: 1, 1.5, Parity Bit Parity bits are used to verify the data packets. Supported values are: Even, Odd, None Time-Out Time-out defines how much time the EMG Series device will wait for a response from the queried unit Delay (for EMG02 and EMG12) When monitoring from more than one place is in effect, this value defines the wait time for the response of queries to be sent to each connected device. This time value may differ according to the device attributes Network Parameters The settings in this section are related to the communication of the ENTES EMG Series device over the internet/intranet infrastructure Connection Settings EMG Series device can work in both server or client mode. If you want to establish a remote connection to the EMG Series device, select the Listens for connection requests option. If you want the EMG Series device to connect to the server and operate as a client, select the Connects to remote server option.

9 DHCP If you want the device to obtain the IP address from the DHCP server, activate this option. It is recommended to use this option only when the EMG Series device is operating in client mode WEB Access If you want the configuration of the device settings from the WEB interface, activate this option WEB Port You can configure the port which will be used for WEB access from here Log-in Time-out When this set time passes after the WEB interface is closed without clicking on Exit button on the interface page, the previous log-in information will be reset and the user will be asked to enter the necessary information again Server IP This option is only active when the EMG Series device is configured as client and defines the server IP address to which the device will be connecting. If the device fails to connect to the server, it will try to reconnect to the server in 1 minute intervals. After the device connects to the server, it sends its MAC address to the server to identify itself IP Address It is for identifying the EMG Series device on the network. Each device on the LAN must have a different IP address. If the device receives its address from DHCP server, the IP address which is received from the DHCP server will be shown in this area Subnet Mask This number defines in which subnet the IP address is. If the device receives its address from DHCP server, the IP address which is received from the DHCP server will be shown in this area Default Gateway This address enables the EMG Series device to access to WAN over a modem or a router. If the device receives its address from DHCP server, the IP address which is received from the DHCP server will be shown in this area.

10 MODBUS/TCP Port Applications which use the TCP/IP protocol while communicating over the internet require a preassigned port number. Some of these port number may already be appointed to other processes. For example, port 80 is reserved for HTTP and port 23 is reserved for TELNET. For MODBUS/TCP protocol, this port number is assigned as 502. It isn't mandatory for the MODBUS/TCP applications to communicate using this port but the software applications must support this port too Link Select the link mode according to the network configuration to which the EMG Series device will be connected Operating Modes EMG Software is able to communicate over TCP protocol using two operating modes. The packet structures and communication is explained next MODBUS/TCP Packet Structure MODBUS/TCP protocol is a revised version of the existing MODBUS protocol to enable communication over the internet. The MODBUS protocol which is used in serial communication applications has a packet structure as shown in Figure 1. Figure 1. Modbus Packet Structure Device Address defines the address of the device on the network to which the received queries will be sent. This address must be different for each device on the RS-485/232 network. Function Code is one of the function codes defined in the MODBUS standard. Data is the data block which contains the information requested from the device or sent by the device. Error Check (CRC) defines the 16 bit long CRC information which is used to verify the data integrity.

11 Some additions to the MODBUS protocol have been made according to the network structure in the MODBUS/TCP protocol. An example of a MODBUS/TCP data packet is given in Figure 2. As you can see, there is an MBAP header in the packet structure. The explanations of the data blocks are given in Figure 2. Figure 2. Modbus Packet Structure Query Number MODBUS protocol is a request/response based protocol. It means that which response belongs to which request is already defined when the first request is created. The information requested by the client in the Nth packet is sent as the Nth response packet by the server. Let's imagine a scenario like below to comprehend the importance of the query number for the communication over the internet.

12 In this scenario, let's imagine that the client produced (N-1)th and Nth request packets one after another and sent those to the gateway over the internet. Although the destination IP address of both packets is the same, these packets may follow different paths to their destinations(for example, (N-1)th packet may follow the A-B-C-D path and Nth packet may follow the A-E-D path). As a result, Nth packet may arrive the destination before (N-1)th packet arrives. If there aren't any numbers which indicate the query order, the gateway will relay the requests to the serial channel and relay back the responses back to the client in the order that they arrived in. But the (N-1)th response sent to the client by the gateway is actually the response for the Nth request. To prevent this kind of confusion while communicating over the internet, a number to define the order of the requests is added into the MODBUS/TCP packet. This number is created by the client and increased for every new request. After the gateway receives and processes the requests in the order that they arrive in, it sends them back in the same order. This way, the client detects which response belongs to which request. Protocol Identifier It is the 16 bit long number that defines to which protocol the packet belongs. For MODBUS/TCP, this number is set as 0. Packet Length It is the length of the following data. Data Address It is the MODBUS address of the serial connected device to which the request will be sent. As seen from the packet structures above, MODBUS/TCP packet doesn't have CRC information. The error control occurs within the TCP protocol itself Tunnel Mode Packet Structure In Tunnel Mode Operation mode, the MBAP header isn't added to the packet. The request/response packets are transmitted embedded in the TCP packet and the CRC information is transmitted along the data block embedded in the TCP packet. TCP Header Modbus Data Figure 3. Tunnel Mod Packet Structure Note: Tunnel mode feature isn't available in the EMG-02 model. CRC

13 2.1.4 Configuration example for communicating over ADSL modem In the example below, an application which shows how you can access your devices which are connected to a remote network using EMG Ethernet-MODBUS Gateway is given. The program in this example runs on a computer with an IP address of and the EMG Series device is placed on the remote network under the sub-net with an IP address of To enable to access to MODBUS Gateway from the remote network, necessary routing configurations on the modem to which the gateway is connected must be made. Furthermore, the default gateway address on the EMG Series device must be entered as the LAN address of the installed ADSL modem, which is The model of the ADSL modem used in this application is AirTies RT111 ADSL2+4. Many modems available on the market are configured using a WEB interface. To change the configuration of your modem, enter the IP address of your modem( in this example) to the address bar of your preferred browser. You will be greeted with the Main Menu.

14 Select the NAT Menu from the left side of the screen and activate this option. Select Port Forwarding under the NAT Menu and add the EMG Series device to the port forwarding list as shown below. After you save the changes you will be able to monitor the serially connected devices over the internet.

15 2.1 Reading/Changing the Configuration using the USB interface You can use the EMG Configuration Tool software in the bundled CD to change the settings on the EMG. To do this; 1. Connect your device using the USB port. 2. POWER LED will light up. 3. Run the file EMG Configuration Tool.exe. 4. After the program starts, the settings of the device will show up automatically.

16 5. After that, you will be able to see the device settings any time you click on the Read button. 6. To change the settings on your device, click on the Update button after you enter the new settings. The new settings will be installed and shown on the program. Not: For the new settings to be in effect, you must power off and on the device. 2.1 Security Settings In this section, you can learn the password which is used to access the device using the WEB interface or change an existing password. To learn your existing password: 1. Click on the Security Settings tab on the EMG Configuration Tool window.

17 2. Under the Password section, your existing password which is used to access the device using the WEB interface will be shown. 3. To change your password, click on the Change Password box. 4. After you enter your new password in the active text fields and click Update button, your new password will be shown. Not: If you committed any changes on the system settings, all of the changes will be installed with the new password. 2.3 Reading/Changing the Configuration using the WEB interface You can also configure the EMG Series device using the WEB interface. Using the port 80 of the HTTP protocol on the gateway, you can access the device settings from a remote computer. The only option you can not change using the WEB interface is the Disable WEB Access option. 1. enter the IP address of your device to the address bar of your preferred browser. If you are connecting from an outside network, enter the IP address of your modem. In this case, the port 80 on the modem must be forwarded to the IP address of the EMG Series device.

18 2. You will be asked to enter a password to access the System Settings. When the device first starts to operate, the default password is emgxx and it is case sensitive(for EMG12 emg12, for EMG-10 emg10, for EMG-02 emg02 ) 3. If you entered the correct password, you will be directed to the settings page. If you enter a wrong password, you will be asked to enter the correct password again(there is no limit).

19 4. After you made the desired setting changes, click on the UPDATE button. To install the settings that you made, click on the Save Changes button. The EMG will reset and your new settings will be activated. 3. Firmware Updates If there are necessary updates or new additions to the EMG firmware, you can install them to the device using the USB port. The latest version of the firmware can be downloaded from Because the firmware update deletes the read-only memory(rom) of the device and the installs the new firmware in this memory, your previous settings will be deleted and replaced with the factory default settings. The file to be installed will be EMG10v.x_x_x.rom or EMG12vx_x_x.rom. v.x_x_x stands for the version information. For the update to be successful, the firmware version of the device and EMG Configuration Tool version must be compatible. Otherwise, a successful firmware update will be out of the question. 1. To update the device firmware, click on the Firmware Update tab on the EMG Configuration Tool.

20 2. Click on the Open button and locate the ROM file you want to insatall. 3. Click on the Update button. After the device is reset, the installation of the new firmware will start. 4. After the firmware update is successful, disconnect the power supply of the device and reconnect it.

21 4. Appendices Appendix A Differences between EMG model devices EMG10: Allows only 1 TCP connection. EMG12 Allows 4 TCP connections at the same time. EMG02 It is similar to EMG12 but allows request only sent to MODBUS addresses 1 and 2. This model also doesn't support the MODBUS Tunnel Mode. Appendix B Query Interval and TCP Time-Out When querying on the Ethernet/MODBUS Gateway devices using the client software, the query interval must not exceed 1.5 minutes. After 1.5 minutes, a counter in the device will be activated and disconnect the network connection. In applications requiring a query interval more than 1.5 minutes, it is recommended to set the client software so that it checks the connection status before every query and reconnect if the connection is down.

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R-

3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R- MODEL ATC-2004 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2004 is a 4 Port RS232/RS485 to TCP/IP converter integrated with a robust system and network management features

More information

1 Serial RS232 to Ethernet Adapter Installation Guide

1 Serial RS232 to Ethernet Adapter Installation Guide Installation Guide 10/100 Mbps LED (amber color ) Link/Activity LED (green color ) 1. Introduction Thank you for purchasing this 1-port RS232 to Ethernet Adapter (hereinafter referred to as Adapter ).

More information

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2

Ethernet Interface Manual Thermal / Label Printer. Rev. 1.01 Metapace T-1. Metapace T-2 Metapace L-1 Metapace L-2 Ethernet Interface Manual Thermal / Label Printer Rev. 1.01 Metapace T-1 Metapace T-2 Metapace L-1 Metapace L-2 Table of contents 1. Interface setting Guiding...3 2. Manual Information...4 3. Interface

More information

User s Manual TCP/IP TO RS-232/422/485 CONVERTER. 1.1 Introduction. 1.2 Main features. Dynamic DNS

User s Manual TCP/IP TO RS-232/422/485 CONVERTER. 1.1 Introduction. 1.2 Main features. Dynamic DNS MODEL ATC-2000 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2000 is a RS232/RS485 to TCP/IP converter integrated with a robust system and network management features designed

More information

RS232 (Serial) to TCP/IP Converter ITEM NO.: SP-RS005

RS232 (Serial) to TCP/IP Converter ITEM NO.: SP-RS005 RS232 (Serial) to TCP/IP Converter ITEM NO.: SP-RS005 SP-RS005 RS232 to Ethernet converters (commonly referred to as Terminal Servers or Device Servers) is designed for transmitting serial data across

More information

Chapter 7 Using Network Monitoring Tools

Chapter 7 Using Network Monitoring Tools Chapter 7 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax NEXT Wireless Router WNR854T. These features can be found by clicking on the Maintenance

More information

Chapter 6 Using Network Monitoring Tools

Chapter 6 Using Network Monitoring Tools Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your Wireless-G Router Model WGR614v9. You can access these features by selecting the items under

More information

Chapter 6 Using Network Monitoring Tools

Chapter 6 Using Network Monitoring Tools Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax Wireless-N Gigabit Router WNR3500. You can access these features by selecting the items

More information

DataTap-IP Configuration Guide 2005 Lava Computer MFG Inc.

DataTap-IP Configuration Guide 2005 Lava Computer MFG Inc. DataTap-IP Configuration Guide 2005 Lava Computer MFG Inc. www.lavalink.com Rev. A04 DataTap-IP Configuration Guide This document describes the configuration features of the DataTap-IP. It covers: 1. Hardware

More information

Chapter 6 Using Network Monitoring Tools

Chapter 6 Using Network Monitoring Tools Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax Dual Band Wireless-N Router WNDR3300. You can access these features by selecting the

More information

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:

To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification: PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,

More information

7.7 Ethernet Communication (AFPX-COM5)

7.7 Ethernet Communication (AFPX-COM5) 7.7 Ethernet Communication (AFPX-COM5) 7.7.1 AFPX-COM5 Overview The communication cassette AFPX-COM5 has an Ethernet interface at the COM1 port and a 3-wire RS232C interface at the COM2 port. The Ethernet

More information

Chapter 1 Configuring Internet Connectivity

Chapter 1 Configuring Internet Connectivity Chapter 1 Configuring Internet Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration

More information

NetBurner PK70EX Port Serial-to-Ethernet Server Users Manual

NetBurner PK70EX Port Serial-to-Ethernet Server Users Manual NetBurner PK70EX-232 4-Port Serial-to-Ethernet Server Users Manual Revision 1.0, January 29, 2008 Table of Contents 1 OVERVIEW...3 2 CONFIGURATION...4 2.1 HARDWARE SETUP...4 2.2 NETWORK CONFIGURATION...4

More information

MODBUS TCP to RTU/ASCII Gateway. User s Manual

MODBUS TCP to RTU/ASCII Gateway. User s Manual MODBUS TCP to RTU/ASCII Gateway User s Manual 1 INTRODUCTION... 1 1.1 FEATURES... 2 1.2 PRODUCT SPECIFICATIONS... 3 1.3 DEFAULT SETTINGS... 4 2 MAKING THE HARDWARE CONNECTIONS... 5 2.1 POWER CONNECTION...

More information

DRO-210i LOAD BALANCING ROUTER. Review Package Contents

DRO-210i LOAD BALANCING ROUTER. Review Package Contents DRO-210i LOAD BALANCING ROUTER Review Package Contents Make sure that the package contains the following items. DRO-210i Load Balancing Router 2 Straight Ethernet Cables 1 Cross Over Ethernet Cable 1 Power

More information

User Manual Network Interface

User Manual Network Interface User Manual Network Interface Rev. 1.00 SRP-350plusll SRP-352plusll http://www.bixolon.com Table of Contents 1. Manual Information...3 2. Specifications...3 2-1 Hardware version...3 2-2 Configuration Tool...3

More information

OSBRiDGE 5XLi. Configuration Manual. Firmware 3.10R

OSBRiDGE 5XLi. Configuration Manual. Firmware 3.10R OSBRiDGE 5XLi Configuration Manual Firmware 3.10R 1. Initial setup and configuration. OSBRiDGE 5XLi devices are configurable via WWW interface. Each device uses following default settings: IP Address:

More information

Chapter 1 Configuring Basic Connectivity

Chapter 1 Configuring Basic Connectivity Chapter 1 Configuring Basic Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration

More information

IP SERIAL DEVICE SERVER

IP SERIAL DEVICE SERVER IP SERIAL DEVICE SERVER ( 1 / 2 / 4 serial port ) Installation guide And User manual Version 1.0 1Introduction... 5 1.1Direct IP mode...5 1.2Virtual COM mode...5 1.3Paired mode...6 1.4Heart beat... 6

More information

VBOX-Plus Configuration Tool

VBOX-Plus Configuration Tool Version 1.0 October 2012 VBOX-Plus Configuration Tool Table of Contents System Requirements Program Installation Connecting to the VBOX-Plus Gateway System Configuration Resetting to Factory Default Registering

More information

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter BIT COMMANDER Serial RS232 / RS485 to Ethernet Converter (Part US2000B) Copyrights U.S. Converters 1 Contents Overview and Features... 3 Functions..5 TCP Server Mode... 5 Httpd Client Mode.5 TCP Auto mode....6

More information

H0/H2/H4 -ECOM100 DHCP & HTML Configuration. H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML Configuration

H0/H2/H4 -ECOM100 DHCP & HTML Configuration. H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML Configuration H0/H2/H4 -ECOM100 DHCP & HTML 6 H0/H2/H4--ECOM100 DHCP Disabling DHCP and Assigning a Static IP Address Using HTML 6-2 H0/H2/H4 -ECOM100 DHCP DHCP Issues The H0/H2/H4--ECOM100 is configured at the factory

More information

TCP/IP Converter DDS EX-9132 Operation Manual for 8051 Series

TCP/IP Converter DDS EX-9132 Operation Manual for 8051 Series TCP/IP Converter DDS EX-9132 Operation Manual for 8051 Series First Edition, March 2005 Table of Contents 1. Introduction 3 Overview 4 Package Checklist 5 Block Diagram 6 Features 7 Product Specifications

More information

Multi-Homing Dual WAN Firewall Router

Multi-Homing Dual WAN Firewall Router Multi-Homing Dual WAN Firewall Router Quick Installation Guide M73-APO09-400 Multi-Homing Dual WAN Firewall Router Overview The Multi-Homing Dual WAN Firewall Router provides three 10/100Mbit Ethernet

More information

DSA-1000 / PRT-1000 Device Server / Thermal Printer

DSA-1000 / PRT-1000 Device Server / Thermal Printer LevelOne DSA-1000 / PRT-1000 Device Server / Thermal Printer User Manual V2.0 TABLE OF CONTENTS 1. INTRODUCTION...- 3-2. DEVICE OVERVIEW...- 7-3. HARDWARE SETUP...- 10-4. SYSTEM CONFIGURATION...- 12 -,

More information

Chapter 2 Managing Your Modem Router

Chapter 2 Managing Your Modem Router Chapter 2 Managing Your Modem Router This chapter describes how to perform management tasks on your ADSL2+ Modem Router DM111PUSP. To use the features described in this chapter, log in to the modem router

More information

Firewall VPN Router. Quick Installation Guide M73-APO09-380

Firewall VPN Router. Quick Installation Guide M73-APO09-380 Firewall VPN Router Quick Installation Guide M73-APO09-380 Firewall VPN Router Overview The Firewall VPN Router provides three 10/100Mbit Ethernet network interface ports which are the Internal/LAN, External/WAN,

More information

Chapter 9 Monitoring System Performance

Chapter 9 Monitoring System Performance Chapter 9 Monitoring System Performance This chapter describes the full set of system monitoring features of your ProSafe Dual WAN Gigabit Firewall with SSL & IPsec VPN. You can be alerted to important

More information

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter

BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter BIT COMMANDER Serial RS232 / RS485 to Ethernet Converter (Part US2000A) Copyrights U.S. Converters 1 Contents Overview and Features... 3 Functions..5 TCP Server Mode... 5 Httpd Client Mode.5 TCP Auto mode....6

More information

Prestige 623R-T. Quick Start Guide. ADSL Dual-link Router. Version 3.40

Prestige 623R-T. Quick Start Guide. ADSL Dual-link Router. Version 3.40 Prestige 623R-T ADSL Dual-link Router Quick Start Guide Version 3.40 February 2004 Introducing the Prestige The Prestige 623R-T ADSL Dual-link Router is the ideal all-in-one device for small networks connecting

More information

Chapter 2 Connecting the FVX538 to the Internet

Chapter 2 Connecting the FVX538 to the Internet Chapter 2 Connecting the FVX538 to the Internet Typically, six steps are required to complete the basic connection of your firewall. Setting up VPN tunnels are covered in Chapter 5, Virtual Private Networking.

More information

Internet Access to a DVR365

Internet Access to a DVR365 Configuration Details : Internet Access to DVR365 Page : 1 Internet Access to a DVR365 These instructions will show you how to connect your DVR365 to the internet via an ADSL broadband modem/router. The

More information

USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6

USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly

More information

Prestige 314 Read Me First

Prestige 314 Read Me First Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER

More information

Broadband Router ESG-103. User s Guide

Broadband Router ESG-103. User s Guide Broadband Router ESG-103 User s Guide FCC Warning This equipment has been tested and found to comply with the limits for Class A & Class B digital device, pursuant to Part 15 of the FCC rules. These limits

More information

UIP1868P User Interface Guide

UIP1868P User Interface Guide UIP1868P User Interface Guide (Firmware version 0.13.4 and later) V1.1 Monday, July 8, 2005 Table of Contents Opening the UIP1868P's Configuration Utility... 3 Connecting to Your Broadband Modem... 4 Setting

More information

ENET-710. ENET-710 - Ethernet Module ENET-710 JAN / 06 FOUNDATION

ENET-710. ENET-710 - Ethernet Module ENET-710 JAN / 06 FOUNDATION ENET-710 ENET-710 - Ethernet Module JAN / 06 ENET-710 FOUNDATION E N E T 7 1 0 ME smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is

More information

TDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module

TDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module Panduit Corp. 2010 TDP43ME NetPS PA26306A01 Rev. 01 11-2010 Network Printer Server Control Center for Ethernet Module NOTE: In the interest of higher quality and value, Panduit products are continually

More information

Chapter 7 Troubleshooting

Chapter 7 Troubleshooting Chapter 7 Troubleshooting This chapter provides troubleshooting tips and information for your ProSafe VPN Firewall 200. After each problem description, instructions are provided to help you diagnose and

More information

Chapter 4 Managing Your Network

Chapter 4 Managing Your Network Chapter 4 Managing Your Network This chapter describes how to perform network management tasks with your ADSL2+ Modem Wireless Router. Backing Up, Restoring, or Erasing Your Settings The configuration

More information

2015/02/07 05:41 1/23 WIZ550WEB Users' Guide

2015/02/07 05:41 1/23 WIZ550WEB Users' Guide 2015/02/07 05:41 1/23 WIZ550WEB Users' Guide WIZ550WEB Users' Guide Overview WIZ550web provides the lightweight webserver operating. It controls digital output or monitors digital and analogue input through

More information

Configuring the WT-4 for ftp (Ad-hoc Mode)

Configuring the WT-4 for ftp (Ad-hoc Mode) En Configuring the WT-4 for ftp (Ad-hoc Mode) Mac OS X Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Mac OS X (10.5.2) ftp server for transmission

More information

STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM

STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This

More information

User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M)

User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) Document code: MN67038-2_ENG Revision 1.400 Page 1 of 25 User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) for

More information

Prestige 324 Quick Start Guide. Prestige 324. Intelligent Broadband Sharing Gateway. Version V3.61(JF.0) May 2004 Quick Start Guide

Prestige 324 Quick Start Guide. Prestige 324. Intelligent Broadband Sharing Gateway. Version V3.61(JF.0) May 2004 Quick Start Guide Prestige 324 Intelligent Broadband Sharing Gateway Version V3.61(JF.0) May 2004 Quick Start Guide 1 1 Introducing the Prestige The Prestige is a broadband sharing gateway with a built-in four-port 10/100

More information

Prestige 324. Prestige 324. Intelligent Broadband Sharing Gateway. Version 3.60 January 2003 Quick Start Guide

Prestige 324. Prestige 324. Intelligent Broadband Sharing Gateway. Version 3.60 January 2003 Quick Start Guide Prestige 324 Intelligent Broadband Sharing Gateway Version 3.60 January 2003 Quick Start Guide 1 Introducing the Prestige The Prestige is a broadband sharing gateway with a built-in four-port 10/100 Mbps

More information

Follow these steps to prepare the module and evaluation board for testing.

Follow these steps to prepare the module and evaluation board for testing. 2 Getting Started 2.1. Hardware Installation Procedure Follow these steps to prepare the module and evaluation board for testing. STEP1: Plug the EG-SR-7100A module into the sockets on the test board.

More information

OvisLink OV804WVA Quick Installation Guide

OvisLink OV804WVA Quick Installation Guide OvisLink OV804WVA Quick Installation Guide 1 Indicators and Interfaces 1.1 Front Panel LED Color Status Description Power Red DSL Internet Red WAN LAN4-1 Off Power off. The initialization is normal. Initiating.

More information

ADSL MODEM. User Manual V1.0

ADSL MODEM. User Manual V1.0 ADSL MODEM User Manual V1.0 CONTENTS 1.OVERVIEW... 3 1.1 ABOUT ADSL... 3 1.2 ABOUT ADSL2/2+... 3 1.3 FEATURES... 3 2 SPECIFICATION... 4 2.1 INTERFACE INTRODUCTION... 4 2.1.1 INDICATOR AND INTERFACE...

More information

Chapter 7 Troubleshooting

Chapter 7 Troubleshooting Chapter 7 Troubleshooting This chapter provides information about troubleshooting your Wireless-G Router Model WGR614v9. After each problem description, instructions are provided to help you diagnose and

More information

Initial Access and Basic IPv4 Internet Configuration

Initial Access and Basic IPv4 Internet Configuration Initial Access and Basic IPv4 Internet Configuration This quick start guide provides initial and basic Internet (WAN) configuration information for the ProSafe Wireless-N 8-Port Gigabit VPN Firewall FVS318N

More information

Liebert IntelliSlot Web Cards

Liebert IntelliSlot Web Cards Monitoring For Business-Critical Continuity Liebert IntelliSlot Web Cards Firmware Upgrade Manual Liebert IntelliSlot Web Card, Liebert IntelliSlot Web Card-LB, Liebert IntelliSlot Web Card-LBDS, Liebert

More information

Nokia Siemens Networks. CPEi-lte 7212. User Manual

Nokia Siemens Networks. CPEi-lte 7212. User Manual Nokia Siemens Networks CPEi-lte 7212 User Manual Contents Chapter 1: CPEi-lte 7212 User Guide Overview... 1-1 Powerful Features in a Single Unit... 1-2 Front of the CPEi-lte 7212... 1-2 Back of the CPEi-lte

More information

Broadband Phone Gateway BPG510 Technical Users Guide

Broadband Phone Gateway BPG510 Technical Users Guide Broadband Phone Gateway BPG510 Technical Users Guide (Firmware version 0.14.1 and later) Revision 1.0 2006, 8x8 Inc. Table of Contents About your Broadband Phone Gateway (BPG510)... 4 Opening the BPG510's

More information

TP-LINK TD-W8901G. Wireless Modem Router. Advanced Troubleshooting Guide

TP-LINK TD-W8901G. Wireless Modem Router. Advanced Troubleshooting Guide TP-LINK TD-W8901G Wireless Modem Router Advanced Troubleshooting Guide Released on 2009.09.25 Version 1.0 Content Summary... 3 Troubleshooting Flow Chart and Resolutions... 3 Check 1... 3 Check 2... 4

More information

DSL-2600U. User Manual V 1.0

DSL-2600U. User Manual V 1.0 DSL-2600U User Manual V 1.0 CONTENTS 1. OVERVIEW...3 1.1 ABOUT ADSL...3 1.2 ABOUT ADSL2/2+...3 1.3 FEATURES...3 2 SPECIFICATION...4 2.1 INDICATOR AND INTERFACE...4 2.2 HARDWARE CONNECTION...4 2.3 LED STATUS

More information

Chapter 1 Connecting Your Router to the Internet

Chapter 1 Connecting Your Router to the Internet Chapter 1 Connecting Your Router to the Internet This chapter describes how to configure your DG834N RangeMax TM NEXT Wireless ADSL2+ Modem Router Internet connection.when you perform the initial configuration

More information

Configuring the WT-4 for ftp (Ad-hoc Mode)

Configuring the WT-4 for ftp (Ad-hoc Mode) En Configuring the WT-4 for ftp (Ad-hoc Mode) Windows XP Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 ftp server

More information

TRP-C31M MODBUS TCP to RTU/ASCII Gateway

TRP-C31M MODBUS TCP to RTU/ASCII Gateway TRP-C31M MODBUS TCP to RTU/ASCII Gateway User s Manual Printed Feb. 2007 Rev 1.0 Trycom Technology Co., Ltd 1F, No.2-11, Sihu street, Yingge Township, Taipei, Taiwan ROC Tel: 886-2-86781191, Fax: 886-2-86781172

More information

Installation and operation manual

Installation and operation manual Installation and operation manual Converter I-7188En-MGTCP Modbus TCP to Modbus RTU Gateway and Router I-7188En-MRTCP Modbus RTU to Modbus TCP Router. GDAŃSK 09.2006 v. 2.0.1. strona 1z1 TABLE OF CONTENTS

More information

User's Manual Ethernet Interface. SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400.

User's Manual Ethernet Interface. SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400. User's Manual Ethernet Interface Rev. 5.00 SRP-270 SRP-275 SRP-280 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400 http://www.bixolon.com Table of contents 1. Interface setting Guiding...3 2.

More information

Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev.

Management Software. Web Browser User s Guide AT-S106. For the AT-GS950/48 Gigabit Ethernet Smart Switch. Version 1.0.0. 613-001339 Rev. Management Software AT-S106 Web Browser User s Guide For the AT-GS950/48 Gigabit Ethernet Smart Switch Version 1.0.0 613-001339 Rev. A Copyright 2010 Allied Telesis, Inc. All rights reserved. No part of

More information

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012

Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012 Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...

More information

Windows NT Server (TCP/IP)

Windows NT Server (TCP/IP) Windows NT Server (TCP/IP) This Document explains how to configure and use the IOPRINT+ Print Server in the Windows NT Server TCP/IP environment. Software Requirements Windows NT3.51 or later TCP/IP network

More information

Prestige 650R-31/33 Read Me First

Prestige 650R-31/33 Read Me First Prestige 650R-31/33 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on

More information

Wireless G Broadband quick install

Wireless G Broadband quick install Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install

More information

Chapter 10 Troubleshooting

Chapter 10 Troubleshooting Chapter 10 Troubleshooting This chapter provides troubleshooting tips and information for your ProSafe Dual WAN Gigabit Firewall with SSL & IPsec VPN. After each problem description, instructions are provided

More information

Quick Installation Guide Wireless Router RNX-EasyN400

Quick Installation Guide Wireless Router RNX-EasyN400 Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, the router automatically enters the self-test phase. During self-test phase, RNX-EasyN400 s Power LED will

More information

ACP ThinManager Tech Notes Troubleshooting Guide

ACP ThinManager Tech Notes Troubleshooting Guide ACP ThinManager Tech Notes Troubleshooting Guide Use the F1 button on any page of a ThinManager wizard to launch Help for that page. Visit www.thinmanager.com/technotes/ to download the manual, manual

More information

One Port Serial Server Users Manual Model ESP901, ESP901E

One Port Serial Server Users Manual Model ESP901, ESP901E One Port Serial Server Users Manual Model ESP901, ESP901E Documentation Number: ESP901-2303 International Headquarters B&B Electronics Mfg. Co. Inc. 707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350

More information

1 PC to WX64 direction connection with crossover cable or hub/switch

1 PC to WX64 direction connection with crossover cable or hub/switch 1 PC to WX64 direction connection with crossover cable or hub/switch If a network is not available, or if it is desired to keep the WX64 and PC(s) completely separated from other computers, a simple network

More information

IP Power Stone 4000 User Manual

IP Power Stone 4000 User Manual IP Power Stone 4000 User Manual Two Outlet Remote AC Power Controller Multi Link, Inc. 122 Dewey Drive Nicholasville, KY 40356 USA Sales and Tech Support 800.535.4651 FAX 859.885.6619 techsupport@multi

More information

Setup and Configuration of Digi Connect WAN Modem with VR-Link (Vector)

Setup and Configuration of Digi Connect WAN Modem with VR-Link (Vector) Setup and Configuration of Digi Connect WAN Modem with VR-Link (Vector) IS10014 Issue 1.0 11 November 2010 Nautel Limited 10089 Peggy's Cove Road, Hackett's Cove, NS, Canada B3Z 3J4 T.877 6 nautel (628835)

More information

MN-700 Base Station Configuration Guide

MN-700 Base Station Configuration Guide MN-700 Base Station Configuration Guide Contents pen the Base Station Management Tool...3 Log ff the Base Station Management Tool...3 Navigate the Base Station Management Tool...4 Current Base Station

More information

Chapter 1 Installing the Gateway

Chapter 1 Installing the Gateway Chapter 1 Installing the Gateway This chapter describes how to set up the wireless voice gateway on your Local Area Network (LAN), connect to the Internet, and perform basic configuration. For information

More information

ROTRONIC Wireless Devices Master Reset and Configuration Settings

ROTRONIC Wireless Devices Master Reset and Configuration Settings ROTRONIC Wireless Devices Master Reset and Configuration Settings Overview... 2 Preparations... 2 Network information... 2 Wireless router settings... 2 Digi Device Discovery... 3 New device from the factory...

More information

Chapter 4 Customizing Your Network Settings

Chapter 4 Customizing Your Network Settings . Chapter 4 Customizing Your Network Settings This chapter describes how to configure advanced networking features of the Wireless-G Router Model WGR614v9, including LAN, WAN, and routing settings. It

More information

Network Setup Guide. 1 Glossary. 2 Operation. 1.1 Static IP. 1.2 Point-to-Point Protocol over Ethernet (PPPoE)

Network Setup Guide. 1 Glossary. 2 Operation. 1.1 Static IP. 1.2 Point-to-Point Protocol over Ethernet (PPPoE) Network Setup Guide 1 Glossary 1.1 Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means

More information

Savvius Insight Initial Configuration

Savvius Insight Initial Configuration The configuration utility on Savvius Insight lets you configure device, network, and time settings. Additionally, if you are forwarding your data from Savvius Insight to a Splunk server, You can configure

More information

T3 Mux M13 Multiplexer

T3 Mux M13 Multiplexer T3 Mux M13 Multiplexer User Manual [Type the abstract of the document here. The abstract is typically a short summary of the contents of the document. Type the abstract of the document here. The abstract

More information

M2M Series Routers. Port Forwarding / DMZ Setup

M2M Series Routers. Port Forwarding / DMZ Setup Introduction Port forwarding enables programs or devices running on your LAN to communicate with the internet as if they were directly connected. Many internet services and applications use designated

More information

Wireless Router Setup Manual

Wireless Router Setup Manual Wireless Router Setup Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10082-02 2006-04 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear,

More information

SIP Proxy Server. Administrator Installation and Configuration Guide. V2.31b. 09SIPXM.SY2.31b.EN3

SIP Proxy Server. Administrator Installation and Configuration Guide. V2.31b. 09SIPXM.SY2.31b.EN3 SIP Proxy Server Administrator Installation and Configuration Guide V2.31b 09SIPXM.SY2.31b.EN3 DSG, DSG logo, InterPBX, InterServer, Blaze Series, VG5000, VG7000, IP590, IP580, IP500, IP510, InterConsole,

More information

Network Interface Table of Contents

Network Interface Table of Contents User Manual Network Interface Rev. 1.05 SLP-TX400 / TX400E SLP-TX403 / TX403E SLP-TX420 / TX420E SLP-TX423 / TX423E SLP-TX220 / TX220E SLP-TX223 / TX223E SLP-DX420 / DX420E SLP-DX423 / DX423E SLP-DX220

More information

User s Manual. Copyright 2010 Vantec Thermal Technologies. All Rights Reserved.

User s Manual. Copyright 2010 Vantec Thermal Technologies. All Rights Reserved. Copyright 2010 Vantec Thermal Technologies. All Rights Reserved. User s Manual Package Contents: 1 NextStar FX Gigabit NAS Adapter x1 2 AC Adapter x1 3 Installation Guide x1 4 Rubber Feet x4 5 User s CD

More information

Enabling NAT and Routing in DGW v2.0 June 6, 2012

Enabling NAT and Routing in DGW v2.0 June 6, 2012 Enabling NAT and Routing in DGW v2.0 June 6, 2012 Proprietary 2012 Media5 Corporation Table of Contents Introduction... 3 Starting Services... 4 Distinguishing your WAN and LAN interfaces... 5 Configuring

More information

Network Management Card. User Manual

Network Management Card. User Manual User Manual 1 Contents Contents 2 Chapter 1 Overview 3 1.1 NMC package contents 4 1.2 NMC CD Resources 4 1.3 Features 4 1.4 NMC Applications 5 Chapter 2 NMC parameters setting via serial COM port 6 2.1

More information

Using IDENT M System T with Modbus/TCP

Using IDENT M System T with Modbus/TCP Using IDENT M System T with Modbus/TCP Introduction The Pepperl+Fuchs IDENT M System T consists of two models MTT3000-F180-B12- V45-MON, which is a read only unit and the MTT6000-F120-B12-V45 which is

More information

Setting Up Your FTP Server

Setting Up Your FTP Server Requirements:! A computer dedicated to FTP server only! Linksys router! TCP/IP internet connection Steps: Getting Started Configure Static IP on the FTP Server Computer: Setting Up Your FTP Server 1. This

More information

This document explains how to use your Web Browser to configure the 100BaseT Print Server models

This document explains how to use your Web Browser to configure the 100BaseT Print Server models Web Browser This document explains how to use your Web Browser to configure the 100BaseT Print Server models Overview 100BaseT Print Server models incorporate a HTTP server. This allows you to connect

More information

TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL

TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL w w w. c d v g r o u p. c o m CA-ETHR-A: TCP/IP Module Installation Manual Page Table of Contents Introduction...5 Hardware Components... 6 Technical Specifications...

More information

Configuring the WT-4 for ftp (Infrastructure Mode)

Configuring the WT-4 for ftp (Infrastructure Mode) Introduction En Configuring the WT-4 for ftp (Infrastructure Mode) This document provides basic instructions on configuring the WT-4 wireless transmitter and a ftp server for transmission over an infrastructure

More information

LAN TCP/IP and DHCP Setup

LAN TCP/IP and DHCP Setup CHAPTER 2 LAN TCP/IP and DHCP Setup 2.1 Introduction In this chapter, we will explain in more detail the LAN TCP/IP and DHCP Setup. 2.2 LAN IP Network Configuration In the Vigor 2900 router, there are

More information

Motorola AP-5131 Access Point Quick Setup Guide

Motorola AP-5131 Access Point Quick Setup Guide Motorola AP-5131 Access Point Quick Setup Guide Ishida / Rice Lake Wireless Communications P/N 109422 Getting Started 1. These instructions were written for the AP-5131 using firmware version 1.1.0.0-045R.

More information

Ethernet Radio Configuration Guide

Ethernet Radio Configuration Guide Ethernet Radio Configuration Guide for Gateway, Endpoint, and Repeater Radio Units April 20, 2015 Customer Service 1-866-294-5847 Baseline Inc. www.baselinesystems.com Phone 208-323-1634 FAX 208-323-1834

More information

Application & Quick-Start Guide

Application & Quick-Start Guide Model: CRMWIC Web Intelligent Controller 1 This document will illustrate various ways to connect and use a CRM-WIC as well as programming examples. When connecting CRM-WIC, the installer has several interface

More information

Chapter 3 Connecting the Router to the Internet

Chapter 3 Connecting the Router to the Internet Chapter 3 Connecting the Router to the Internet This chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to configure your DG834GT

More information

GV-Data Capture V3 Series User's Manual

GV-Data Capture V3 Series User's Manual GV-Data Capture V3 Series User's Manual Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. 2006 GeoVision, Inc. All rights

More information

Debugging Network Communications. 1 Check the Network Cabling

Debugging Network Communications. 1 Check the Network Cabling Debugging Network Communications Situation: you have a computer and your NetBurner device on a network, but you cannot communicate between the two. This application note provides a set of debugging steps

More information