OTAGO DISPENSER DP30. Infiltration pump. The Otago Dispenser DP30 is a pump for infiltration during liposuction.

Transcription

1 OTAGO DISPENSER DP30 Infiltration pump The Otago Dispenser DP30 is a pump for infiltration during liposuction.

2 FEATURES AND BENEFITS The Otago Dispenser DP 30 is a pump for infiltration of aqueous solutions into human connective tissues. It is particularly well-suited for use as an infiltration pump in liposuction and varicose vain treatments. The lipolysis process is significantly improved by its use, making subsequent liposuction much easier. Good price/performance ratio Cost effective infiltration for liposuction Continuously variable and precise adjustable infiltration pump Allows surgeon/operator effective control of tumescence during infiltration stage of liposuction Pedal with on/off function Allows operator to deliver desired volumetric displacement thereby improving infiltration process Stand for irrigation fluid bottle Compact unit with stand allows operator to attach tumescence bag ensuring effective infiltration Very fast and easy fixing of the tubing set Ensures quick and efficient infiltration stage. TECHNICAL DATA Otago Dispenser DP 30 Voltage: switchable: 100 V~/ 115 V~/ 230 V~, Hz Fuse, power supply: (2 fuses) T 1 AL 250 V AC Power consumption: 40 VA Volumetric displacement: l/h Maximum pressure with closed tube set: 2.0 bar Protection class: Class II Applied part (Applied part is the tube set with its attached instruments): Type BF Dimensions (W x D x H): 260 x 250 x 110 mm Net weight control unit: 2.4 kg The mentioned volumetric displacement is only valid for aqueous solutions without any instrument connected. DEVICE OVERVIEW 1. Indicator light for Power On/Off 2. Operating panel with pump displacement scale 3. Control dial to set pump displacement volume 4. Release key for tubing set bracket 5. Peristaltic pump 6. Tubing set 7. Stand for irrigation fluid bottle 8. Roller clam 9. Venting valve 10. Irrigation fluid 11. Type plate with type designation, reference number, serial number, information on power supply and device fuse 12. Pedal socket, device rear 13. Potential equalization 14. Power entry module with power plug socket 15. Power entry module with power switch 16. Power entry module with national voltage setting Front view 10 9 Rear view

3 STARTING UP Connection to the power supply In order to prevent the risk of electric shock, the device may only be connected to a power network with a PE protective earth conductor. If the voltage shown does not correspond to the local mains voltage, the grey fuse holder must be set to the correct voltage: 1. Press release key for tubing set bracket (on top of the control unit) to open the pump. 2. The compartment with the integrated tubing bracket opens. 3. Place the tubing set into the tubing bracket provided in such a way that the part of the tubing set with the spike exits the pump towards the rear of the device. Make sure the tubing is secure. 4. With the tubing set inserted, press the compartment downwards until it clicks into place. A) Switch off device. B) Unplug the power cable. C) Use a screwdriver to open the fuse slot. D) Remove the fuse holder. E) Remove the grey fuse holder and reinsert it so that the local mains voltage setting is shown in the small window. F) Slide the grey fuse holder back in and close the fuse slot. G) Check the mains voltage shown on the fuse slot. H) Plug the power cable back into the device. Device preparation 1. Insert the stand for the irrigation fluid into the stand holder. 2. Plug the pedal plug into the pedal socket at the rear of the control unit. 3. Assemble the tubing set (see images). Check the expiry date of the tubing set and ensure that the packaging is not damaged. Using non-sterile tubing sets can result in serious infection, and in extreme cases, can be fatal. 5. Insert the spike at the end of the tubing set into the irrigation fluid bottle and hang the bottle onto the stand. 6. Open the roller clamp on the tubing set as far as it will go. 7. Open the vent valve at the spike. 8. Connect the control unit to the power socket. Ensure that the operating voltage setting corresponds to the local mains voltage. When inserting the tubing set, notice the arrow marked on the tubing set bracket. It indicates the direction of flow of the infiltration liquid. Do not regulate the amount of irrigation fluid using the roller clamp on the tube set; with the Otago Dispenser DP 30, this is regulated instead using the control dial and the foot pedal. For this reason, make sure to open the roller clamp as far as it will go. Use only the Otago tube set, otherwise the function cannot be guaranteed. Device setup Place the Otago Dispenser DP 30 and all required accessories and instruments on an even, non-slip surface and make sure you have good access to all controls. Do not allow the operating range of the device (including the cable) to be compromised by limiting factors. The system operation panel and the infiltration liquid bottle must be fully visible at all times. It must be explicitly ensured that no objects can fall on the pedal. The power plug at the rear of the device must be accessible at all times.

4 OPERATION Switching the device on and off Use the power switch I/O at the rear of the control unit to switch the control unit on and off. The device may be switched off at any time irrespective of any procedure for switching off the device. The green indicator light up left on the operation panel is on, when the main switch is switched on and the device is ready for operation. OTAGO DP30 CONSUMABLE Sterile tube set for infiltration with a length of 4 meters. Regulation of the infiltration process ORDERING Otago Dispenser DP30 With ON/OFF pedal Control dial in conjunction with ON/OFF pedal The desired volumetric displacement is set with the control dial. The pumping process is started by actuating the ON/OFF pedal. The volumetric displacement can be varied at any time using the control dial. Code Product description 4184 Dispenser DP30 control unit 6022 Tubing set, 4 m, single use 1770 Stand for irrigation fluid bottle 1813 on/off pedal, IPX8 Flexible tube pump Turn control dial clockwise from the OFF position. Pump starts, liquid emerges from the open tube end. Turning the dial up to the maximum value controls the increase in volumetric displacement. The pump stops immediately when the release button of the pump compartment is pressed. Functional check Prior to Otago Dispenser DP 30 startup or use of accessory equipment, the user must always ensure that each individual component is in good working order, free of defects, clean, sterile and operational. The tube set has to correspond with the correct flow direction and the pump has to function. The green LED is on after the device is switched on.

5 Global Distributor Otago Healthcare Mobbs Miller House Unit 19C, Ardington Road Northampton NN1 5NE United Kingdom. Tel: +44 (0) Technical Support & Enquires (24hr):- Tel: +44(0) OTAGO DISPENSER DP30 CE 0197 Manufacturer: Nouvag AG St.Gallerstr CH-9403 Goldach, Switzerland Phone +44(0) Fax +44(0) Authorized Representative in Europe: Nouvag AG