Carbon Film Fixed Resistor CB Series
|
|
|
- Jeffery Manning
- 7 years ago
- Views:
Transcription
1 DIP Carbon Film Fixed CB Series Features Lowest cost, prompt delivery Excellent long term stability Wide resistance range 0Ω22~100MΩ Power ratings TYPE / Rated Power at 70 L D H d Comment Standard Miniature 1/8W 1/4WS 3.3± 0.4 Standard Series: Light ±0.3 26± ± Brown (khaki) Color Epoxy 1/4W 1/2WS 6.3± ±0.3 26± ±0.03 Coating 1/3W 1/2WSS 8.5± ±0.5 26± ±0.03 1/2W 1WS 9.0± ±0.5 26± ±0.03 Miniature Series: Pink Color Epoxy Coating 1W 2WS 11.5± ±0.5 30± ±0.03 2W 3WS 15.5± ±0.5 32± ±0.03 Electrical Characteristics Power rating at 70 1/8W 1/4WS 1/4W 1/2WS 1/3W 1/2WSS 1/2W 1WS 1W 2WS 2W 3WS Operating Temp. Range -55 to +155 Max. Working Voltage 150V 200V 250V 300V 280V 320V 350V 400V 450V 500V 500V 500V Max. Overload Voltage 300V 400V 500V 500V 500V 600V 700V 800V 1000V 1000V 1000V 1000V Dielectric Withstanding Voltage Resistance Range (±5%) 300V 400V 500V 500V 500V 600V 700V 800V 1000V 1000V 1000V 1000V 1Ω~10MΩ, E24 series For non-standard parts, please contact our sales dept. Power Graph ( ) Hot-Spot Temperature (%) Rated Load(%) 70 SURFACE TEMP. RISE ( ) CB 2WS CB 200/CB1WS CB 100/CB50S CB 50 / CB25S CB 12 / CB25 Ambient Temperature ( ) Applied Load % of RCWV
2 Temperature Coefficient (T.C.R.) TYPE Max. of Temp. Coefficient ppm/ under 100KΩ 100KΩ to 1MΩ 1MΩ to 4M7Ω 1W, 2W, 2WS, 3WS ±350 ppm -0ppm -500ppm -0ppm -1000ppm 1/6W, 1/4W, 1/4WS, 1/2W, 1/2WS, 1WS +350ppm- 500ppm -0ppm-700ppm -0ppm-1500ppm Environmental Characteristics Performance Test Test Method Requirements Short Time Overload JIS-C times RCWV for 5 seconds ±(0.75%+0.05Ω) Temperature Coefficient Resistance (T.C.R.) Resistance value at room Temperature and room Temperature+100 page Dielectric Withstanding Votage JIS-C In V-Block for 60 seconds By Pulse Overload JIS-C times RCWV for 10000cycles(1sec.on,25secs.off) ±(1%+0.05Ω) Insulation Resistance JIS-C In V-Block >10000MΩ Load Life Load Life in Humidity Solder Ability JIS-C at RCWV for 1000hrs.(1.5hrs. on,0.5hrs.off) JIS-C ±2 90~95%RH at RCWV for 1000hrs. (1.5hrs. on,0.5hrs.off) JIS-C ±5 for 2±0.5 seconds ±(3%+0.05Ω) Less than 100KΩ±3% 100KΩ or more±5% 95% min. coverage Resistance to Solvent JIS-C Trichroethane for 1 min. with ultrasonic No deterioration of coatings and markings Terminal Strength Direct load for 10 sec. In the direction off the terminal leads. Tensile: 2.5kg Rated continuous Working Voltage (RCWV) = POWER.RATING.* RESISTANCE.VALUE
3 Parts Number Explanation CB 1/2W J 10R P 05 (Inch) 1/8W 1/4W 1/3W 1/2WS 1/2WSS J:±5% s P W:Tape D:Bulk 1/4WS 1W 1WS 2W 2WS 3W
4 Metal Film MF Series Features Low noise Low t.c.r. 100ppm, 50ppm, 25ppm, 10ppm, 5ppm. High precision 1%, 0.5%, 0.25%, 0.1% TYPE / Rated Power at 70 L D H d Comment Standard Miniature 1/8W 1/4WS 3.3± 0.4 Standard Series: Blue Color 1.8±0.3 29± ± Epoxy Coating 1/4W 1/2WS 6.3± ±0.3 28± ±0.03 Miniature Series: 1/2W 1WS 9.0± ±0.5 26± ±0.03 Blue Color Epoxy Coating 1W 2WS 11.5± ±0.5 35± ±0.03 2W 3WS 15.5± ±0.5 32± ±0.03 Electrical Characteristics Power rating at 70 1/8W 1/4WS 1/4W 1/2WS 1/2W 1WS 1W 2WS 2W 3WS Operating Temp. Range -55 to +155 Max. Working Voltage 200V 200V 250V 300V 350V 400V 450V 500V 500V 500V Max. Overload Voltage 400V 400V 500V 600V 700V 800V 1000V 1000V 1000V 1000V Dielectric Withstanding Voltage 300V 400V 500V 500V 500V 700V 1000V 1000V 1000V 1000V Resistance Range (±1%.±0.5%) 10Ω~1MΩ, E96series Resistance Range (±0.25%.±0.1%) 100Ω~100KΩ, E192series For non-standard parts, please contact our sales dept. Power Graph ( ) Hot-Spot Temperature (%) Rated Load(%) 70 Ambient Temperature ( ) SURFACE TEMP. RISE ( ) Applied Load % of RCWV MF 2WS MF 200 / MF 1WS MF 100 / MF 50S MF 50 / MF 25S MF 25 MF 12
5 Temperature Coefficient (T.C.R.) TYPE Max. of Temp. Coefficient ppm/ 1/8W, 1/4W, 1/4WS, 1/2W, 1/2WS, 1W, 1WS, 2W, 2WS, 3WS ±15ppm/, ±25ppm/, ±50ppm/, ±100ppm/ Environmental Characteristics Performance Test Test Method Requirements Short Time Overload JIS-C times RCWV for 5 seconds ±(0.25%+0.05Ω) Temperature Coefficient Resistance (T.C.R.) Resistance value at room Temperature and room Temperature+100 By Dielectric Withstanding Votage JIS-C In V-Block for 60 seconds By Pulse Overload JIS-C times RCWV for cycles(1sec.on,25secs.off) ±(0.75%+0.05Ω) Insulation Resistance JIS-C In V-Block >10000MΩ Load Life Load Life in Humidity JIS-C at RCWV for 1000hrs.(1.5hrs. on,0.5hrs.off) JIS-C ±2 90~95%RH at RCWV for 1000hrs. (1.5hrs. on,0.5hrs.off) ±(1.5%+0.05Ω) ±(1.5%+0.05Ω) Solder Ability JIS-C ±5 for 2±0.5 seconds 95% min. coverage Resistance to Solvent JIS-C Trichroethane for 1 min. with ultrasonic No deterioration of coatings and markings Terminal Strength Direct load for 10 sec. In the direction off the terminal leads. Tensile: 2.5kg Rated continuous Working Voltage (RCWV) = POWER.RATING.* RESISTANCE.VALUE
6 Parts Number Explanation MF 1/8W D 10R P 05 (Inch) 1/8W 1/4W 1/3W 1/2WS B:±0.1% C:±0.25% D:±0.5% F:±1% s P W:Tape D:Bulk 1/2W 1/4WS 1W 1WS 2W 2WS 3W
7 Metal Oxide Flame-Proof MO Series Features Low cost, prompt delivery High power-to-size ratio for significant space savings Excellent long-time stability Complete flameproof construction UL 1412 High surge/overload capability Wide resistance range: 0.1Ω~1mΩ Controlled temperature coefficient Resistance standard tolerance:±5%(consult factory for±2% ±1%) Coating and marking resist trichorethelyne, freon, and other cleaning agents Non-inductive design, resistance range: 0.1Ω~100Ω TYPE / Rated Power at 70 Standard Miniature L D H d Comment 1/4W 1/2WS 6.3± ±0.3 28± ±0.03 1/2W 1WS 9.0± ±0.5 26± ±0.03 1W 2WS 11.5± ±0.5 35± ±0.03 2W 3WS 15.5± ±0.5 32± ±0.03 Standard Series: Flameproof Coating, Grey color Miniature Series: Flameproof Coating, Pink color 3W 5WS 17.5± ±0.5 35± ±0.03 5W 7WS 24.5± ±0.5 35± ±0.03 Electrical Characteristics Power rating at 70 1/4W 1/2WS 1/2W 1WS 1W 2WS 2W 3WS 3W 5WS 5W 7WS Operating Temp. Range -55 to +155 Max. Working Voltage 200V 250V 250V 300V 350V 350V 350V 400V 400V 750V 750V 750V Max. Overload Voltage 350V 400V 400V 500V 600V 600V 600V 700V 700V 1000V 1000V 1000V Dielectric Withstanding Voltage Resistance Range (±1%.±2%.±5%) 350V 350V 350V 400V 500V 500V 500V 600V 600V 1000V 1000V 1000V 1Ω~510KΩ, E24 series For non-standard parts, please contact our sales dept. Power Graph ( ) Hot-Spot Temperature (%) Rated Load(%) 70 Ambient Temperature ( ) SURFACE TEMP. RISE ( ) Applied Load % of RCWV MO 3B 5B/ MO 7WS MO 2WS/ MO 3WS MO 2B / MO 1WS MO 1B MO 1/2B MO 1/4B
8 Temperature Coefficient (T.C.R.) TYPE 1/4W, 1/2WS, 1/2W, 1WS 1W, 2WS, 2W, 3WS, 3W, 5W, 5WS, 7WS Max. of Temp. Coefficient ppm/ ±300 ppm Environmental Characteristics Performance test Test Method Requirements Short time Overload JIS-C times RCWV for 5 seconds ±(0.25%+0.05Ω) Temperature Coefficient Resistance (T.C.R.) Resistance value at room Temperature and room Temperature+100 By Dielectric Withstanding Voltage JIS-C In V-Block for 60 seconds By Pulse Overload JIS-C times RCWV for 10000cycles(1sec.on,25secs.off) ±(1%+0.05Ω) Insulation Resistance JIS-C In V-Block >10000MΩ Load Life Load Life in Humidity JIS-C at RCWV for 1000hrs.(1.5hrs. on,0.5hrs.off) JIS-C ±2 90~95%RH at RCWV for 1000hrs. (1.5hrs. on,0.5hrs.off) ±(1.5%+0.05Ω) ±(1.5%+0.05Ω) Solder Ability JIS-C ±5 for 2±0.5 seconds 95% min. coverage Resistance to Solvent JIS-C Trichroethane for 1 min. with ultrasonic No deterioration of coatings and markings Terminal Strength Direct load for 10 sec. In the direction off the terminal leads. Tensile: 2.5kg Rated continuous Working Voltage (RCWV) = POWER.RATING.* RESISTANCE.VALUE
9 Parts Number Explanation MO 1/4W F 10R P 05 (Inch) 1/4W 1/2WS 1/2W 1W F:±1% G:±2% J:±5% s P W:Tape D:Bulk 1WS 2W 2WS 3W 5W 5WS 7WS
10 Wirewound s Flame -Proof Coating KNP Series Features Super heat dissipation;small linear temperature coefficient Instant overload capability;low noise figure and without annual shift on resistance value Complete flameproof construction UL-1412 Identify NKNP by fifth color band with green color. range ±5% ±2% ±1% TYPE / Rated Power at 70 Standard Miniature L D H d Comment 1/2W 1WS 9.0± ±0.5 26± ±0.03 1W 2WS 11.5± ±0.5 35± ±0.03 2W 3WS 15.5± ±0.5 32± ±0.03 3W 5WS 17.5± ±0.5 32± ±0.03 Standard Series:Grey Color Epoxy Coating Miniature Series: Pink Color Epoxy Coating 5W 7WS 24.5± ±0.5 38± ±0.03 Electrical Characteristics Power rating at 70 1/2W 1WS 1W 2WS 2W 3WS 3W 5WS 5W 7WS Operating Temp. Range -55 to +155 Dielectric Withstanding volt Resistance Range (±1%, ±2%, ±5%) 300V 400V 0.01Ω~50Ω 0.01Ω~100Ω 0.01Ω~330Ω 0.01Ω~330Ω 0.01Ω~560Ω For non-standard parts, please contact our sales dept. Power Graph ( ) Hot-Spot Temperature (%)
11 Temperature Coefficient (T.C.R.) TYPE 1/2W, 1WS, 1W, 2W, 2WS, 3W, 3WS, 5W, 5WS, 7WS Max. of Temp. Coefficient ppm/ ±400 ppm Environmental Characteristics Performance test Test Method Requirements Short time Overload JIS-C times RCWV for 5 seconds ±(2%+0.05Ω) Temperature Coefficient Resistance (T.C.R.) Resistance value at room Temperature and room Temperature+100 By Dielectric Withstanding Voltage JIS-C In V-Block for 60 seconds By Insulation Resistance JIS-C In V-Block >100MΩ Load Life Load Life in Humidity JIS-C at RCWV for1000hrs.(1.5hrs. on,0.5hrs.off) JIS-C ±2 90~95%RH at RCWV for1000hrs. (1.5hrs. on,0.5hrs.off) ±(5%+0.05Ω) ±(5%+0.05Ω) Solder Ability JIS-C ±5 for 2±0.5 seconds 95% min. coverage Terminal Strength Direct load for 10 sec. In the direction off the terminal leads. Tensile: 2.5kg Rated continuous Working Voltage (RCWV) = POWER.RATING.* RESISTANCE.VALUE
12 Parts Number Explanation KNP 1/2W J 10R P 05 (Inch) 1/2W 1/2WS 1/W F:±1% G:±2% J:±5% s P W:Tape D:Bulk 1WS 2W 2WS 3W 3WS 5W 5WS 7WS
13 Cement SPS Series L Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. TYPE L W D P Wirewound RESISTANCE RANGE Ω RS 5W Ω ~ 200 Ω 200 Ω ~ 50K Ω 7W Ω ~ 300 Ω 300 Ω ~ 50K Ω 10W Ω ~ 500 Ω 500 Ω ~ 50K Ω 20W Ω ~ 500 Ω 500 Ω ~ 50K Ω Parts Number Explanation SPS 5W J 10R P 01 (Inch) 5W 7W 10W 20W J:±5% K:±10% s P W:Bulk SQM Series
14 Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. TYPE H ± 1.5 W ± 1 S ± 1 RESISTANCE RANGE Ω Wirewound Metal oxide 5W Ω ~ 50 Ω 50 ~ 50K Ω 7W Ω ~ 500 Ω 500 ~ 47K Ω 10W Ω ~ 500 Ω 500 ~ 47K Ω 10WS Ω ~ 500 Ω 500 ~ 47K Ω Parts Number Explanation SQM 5W J 10R P 01 5W 7W 10W 10WS J:±5% K:±10% s P W:Bulk
15 SQT Series Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. TYPE W ± 1 H ± 1 L ± 1 t ± 0.5 RESISTANCE RANGE Ω Wire wound Metal oxide 5W Ω ~ 50 Ω 50 ~ 50K Ω 7W Ω ~ 500 Ω 500 ~ 47K Ω 10W Ω ~ 500 Ω 500 ~ 47K Ω 15W Ω ~ 500 Ω 500 ~ 47K Ω 20W Ω ~ 500 Ω 500 ~ 47K Ω Parts Number Explanation SQT 5W J 10R P 01 (Inch) 5W 7W 10W 15W 20W J:±5% K:±10% s P W:Bulk
16 SQP Series Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. RESISTANCE RANGE Ω TYPE L ± 0.5 W ± 0.5 H ± 0.5 d ± 0.03 Wire wound Metal oxide 2W Ω ~ 50 Ω 50Ω~ 200K Ω 3W Ω ~ 50 Ω 50Ω~ 330K Ω 5W Ω ~ 50 Ω 50Ω~ 500K Ω 7W Ω ~ 500 Ω 500Ω~ 500K Ω 10W Ω ~ 500 Ω 500Ω~ 500K Ω 15W Ω ~ 500 Ω 500Ω~ 150K Ω 20W Ω ~ 500 Ω 500Ω~ 150K Ω 25W Ω ~ 500 Ω 500Ω~ 150K Ω 30W Ω ~ 500 Ω 500Ω~ 150K Ω 40W Ω ~ 500 Ω 500Ω~ 150K Ω Parts Number Explanation SQP 2W J 10R P 01 (Inch) 2W 3W 5W 7W 10W 15W 20W 25W 30W 40W J:±5% K:±10% s P W:Bulk
17 SQZ Series Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. TYPE L H W S H1 H2 P1 P2 P3 P4 RESISTANCE RANGE Ω Wire wound Metal oxide 5W ~ 100 Ω 100 Ω ~ 50K Ω 7W ~ 500 Ω 500 Ω ~ 50K Ω 10W ~ 500 Ω 500 Ω ~ 50K Ω 15W ~ 500 Ω 500 Ω ~ 150K Ω 20W ~ 50 Ω 500 Ω ~ 150K Ω 3WS ~ 50 Ω 50 Ω ~ 33K Ω 5WS ~ 50 Ω 50 Ω ~ 50K Ω Parts Number Explanation SQM 5W J 10R P 01 5W 7W 10W 10WS J:±5% K:±10% s P W:Bulk
18 SQH / SQHG Series SQH Series SQHG Series Features Heat and flame resistant Completely insulated character suitable for printed circuit bord. For high resistance value, the winding core will be replaced by metal oxide film cutting core (RS type). Non-inductive type is available on request. : ±5% ±10%. TYPE RESISTANCE RANGE Ω Wire wound Metal oxide L±2 H±1 W±1 S±1 H±1 P1±1 P2±1 P3±1 P4±1 d 10W 0.5 Ω ~ 100 Ω 500 Ω ~ 50K Ω W 1 Ω ~ 500 Ω 500 Ω ~ 150K Ω W 1 Ω ~ 500 Ω 500 Ω ~ 150K Ω W 1 Ω ~ 500 Ω W 1 Ω ~ 500 Ω Parts Number Explanation SQH 10W J 10R P 01 (Inch) 10W 15W 20W 30W 40W J:±5% K:±10% s P W :Bulk
19 Technical Data
DATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
Pulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
Part Marking Instructions Chip Resistors
Chip Resistors Part Marking Instructions Part Marking Instructions Chip Resistors 1% Marking The nominal resistance is marked on the surface of the overcoating with the use of 4 digit markings. 0201 and
Type RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
SMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
SPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
High-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
Metal Film Resistors, Industrial, Precision
Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Available Excellent high frequency characteristics Exceptionally
Metal Film Resistors, Industrial, Precision
CMF Industrial Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
High-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
Carbon Film Fixed Resistor Axial Leaded
Features Automatically insertable High quality performance Non-Flame type available Cost effective and commonly used Too low or too high values can be supplied on case to case basis Performance Specification
High Power Thick Film Chip Resistor 2512
Specifications: Type : MCHP12 Power Rating at 70 C : 2W Working Voltage : 250V Max. Overload Voltage : 500V Max. Dielectric Withstanding Voltage : 500V Temperature Range : -55 C to +155 C Ambient Temperature
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
Precision Leaded Resistors
FEATURES Approved according to CECC 40101-806 Advanced thin film technology Low TC: ± 15 to Precision tolerance of value: ± 0.1 % and ± 0.25 % Superior overall : class 0.05 Wide precision range: 10 Ω to
Automotive and Anti-Sulfuration Chip Resistor 0402
The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top surface of the
Precision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
Metal Film Resistors, Military, MIL-R-10509 Qualified, Type RN and MIL-PRF-22684 Qualified, Type RL
CMF (Military RN and RL) Metal Film Resistors, Military, Qualified, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient
High Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
Thick Film Resistor Networks, Dual-In-Line, Molded DIP
Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick
Metal Film Resistors, Non-Magnetic, Industrial, Precision
Metal Film Resistors, Non-Magnetic, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
High Ohmic/High Voltage Metal Glaze Leaded Resistors
VR37 High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded
Selection Guide for Conversion of Carbon Composition Resistors
Selection Guide for Conversion of Carbon Composition Resistors believes that the information described in this publication is accurate and reliable, and much care has been taken in its preparation. However,
Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
FEATURES 200 % 175 % 150 % 125 % 100 % 75 % 50 % 25 %
Ultra High Precision Z-Foil Resistor with TCR of ± 0.05 ppm/ C, PCR of 5 ppm at Rated Power, Tolerance of ± 0.005 % and Load Life Stability of ± 0.005 % INDUSTRY BREAKTHROUGH Any value at any tolerance
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
Metal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
Metal Film Resistors, Military, Qualified, Precision, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient Flame retardant
High Surge Axial Cemented Wirewound Resistors
High Surge Axial Cemented Wirewound Resistors FEATURES High voltage surge (up to 12 kv) withstanding capability Non flammable silicon cement coating High grade ceramic core Material categorization: for
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
Capacitance Cap. Tol. Suffix construction. Rated voltage
Metallized Polypropylene Film Capacitors Type:ECWFE Plastic Film Capacitors Non-inductive construction using metalized Polypropylene film with flame retardant plastic case. Features Small size Excellent
High Ohmic / High Voltage Metal Glaze Leaded Resistors
High Ohmic / High Voltage Metal Glaze Leaded Resistors A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper
Metal Film Resistors, Industrial, Flameproof
End of Life - August 13 Metal Film Resistors, Industrial, Flameproof STANDARD ELECTRICAL SPECIFICATIONS FEATURES Small physical size Low cost resistors have the ability to withstand overloads up to times
Power Meter Series 700
PowerLogic power-monitoring units Power Meter Series 700 Technical data sheet 2007 Functions and characteristics E90463 The PowerLogic Power Meter Series 700 offers all the measurement capabilities required
High Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
Ceramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
SMD PTC - Nickel Thin Film Linear Thermistors
SMD PTC - Nickel Thin Film Linear Thermistors Notes (1) Contact if closer TCR lot tolerance is desired. (2) Other R 25 -values and tolerances are available upon request. (3) Rated continuous working voltage
Insulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
High Ohmic/High Voltage Metal Film Leaded Resistors
, High Ohmic/High Voltage FEATURES Metal film technology High pulse loading (up to 10 kv) capability Small size (0207/0411) Compatible with lead (Pb)-free and lead containing soldering processes Compliant
DATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',
SPECIFICATION. Topview 5550 SMD LED IWS 505-RB. Product : Topview 5550 SMD LED Part No : IWS-505-RB Customer : Date : 2007. 11. 10 Ver.1.0.
SPECIFICATION Product : Topview 555 SMD LED Part No : Customer : Date : 27.. Ver.. Customer : Approval Manufacturer : ITSWELL Co., LTD Proposed By Approval Comment Suwon Company : 442-9, 82 Uman Industrial
AZ420 MINIATURE GENERAL PURPOSE RELAY
MINIATURE GENERAL PURPOSE RELAY FEATURES Rugged construction for high reliability Life expectancy greater than 0 million operations DC coils to 11 V Power consumption as low as 2 mw per pole available
Fixed Resistors. RESISTORS FOR MEDICAL APPLICATIONS - Application Note
The electronic content of devices for medical applications continues to rise steadily as medical science develops new techniques and electronic engineering supplies new solutions. At the same time, these
5W HI-POWER LED SPECIFICATION
5W HI-POWER LED SPECIFICATION HPG8b-495xWHCx Drawn by Checked by Approved by RoHS Conformity DATE:2013/4/9 REV:A HUEY JANN High Power 5W LED is made of GaInN chips with precise package technique which
Professional Thin Film MELF Resistors
,, - Professional Professional Thin Film MELF Resistors, and professional thin film MELF resistors are the perfect choice for most fields of rn professional electronics where reliability and stability
DATA SHEET PART NO. : L-314YD REV : A / 4
PARA LIGHT ELECTRONICS CO., LTD. 4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan, R.O.C. Tel: 886-2-2225-3733 Fax: 886-2-2225-4800 E-mail: para@para.com.tw http://www.para.com.tw DATA SHEET
Wirewound Resistors, Industrial Power, Aluminum Housed, Chassis Mount
Wirewound Resistors, Industrial Power, Aluminum Housed, hassis Mount FEATURES Molded construction for total environmental protection omplete welded construction Meets applicable requirements of MIL-PRF-18546
Contents. 12. Lot Number 10. 13. Reel Packing Structure 11. 14. Precaution for Use 13. 15. Hazard Substance Analysis 14. 16. Revision History 18
Rev : 00 ISSUE NO : DATE OF ISSUE : 2009. 04. 10 S P E C I F I CATION MODEL : SLHNNWW629T1S0U0S0 [Rank : (S0), (U0), (S0)] HIGH POWER LED - SUNNIX6 CUSTOMER : CUSTOMER CHECKED CHECKED APPROVED SAMSUNG
Series AMEPR30-AZ up to 2.5A AC-DC / DC-DC LED Driver / Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Max Output Power (W) 1 AC-DC Constant Current or Constant Over temperature protection Voltage LED Driver Over current
Ultra Precision Metal Film Leaded Resistors
Ultra Precision Metal Film Leaded Resistors FEATURES Exceptional low TCR: ± 2 ppm/k to ± 10 ppm/k Super tight tolerance: ± 0.01 % to ± 0.25 % Exceptional overall stability: class 0.02 Wide resistance range:
EVERGREEN (C.P.) USA INC. TEL: (650) 952-8091 FAX: (650) 952-3629 E-MAIL: sales@evergreencpusa.com. SPECIFICATIONS Lithium Battery CR123A- 1700mAh
Voltage (V) Voltage (V) Voltage (V) EVERGREEN (C.P.) USA INC. SPECIFICATIONS Lithium Battery CR123A- 1700mAh Temperature characteristics(20ma) (mah) Pulse discharge characteristics Model CR123A Nominal
Power Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
3. ELECTRICAL PERFORMANCE PROPERTY TEST CONDITION PERFORMANCE 3. 1 Contact Resistance 1) Center Push 100mΩ Max
1. GENERAL 1. 1 Application : This specification is applied to MULTI WAY SWITCH for electronic equipment. 1. 2 Operating Temperature Range :-25 ~ 70 1. 3 Storage Temperature Range :-0 ~ 85. However, 96
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator
NTE923 & NTE923D Integrated Circuit Precision Voltage Regulator Description: The NTE923 and NTE923D are voltage regulators designed primarily for series regulator applications. By themselves, these devices
Insulation Resistance Testing of Low Voltage Cables in the Field
Insulation Resistance Testing of Low Voltage Cables in the Field Table of Contents 1. Background...3 1.1. Before Making Measurements...3 1.2. How to Apply the Temperature Correction Factor...4 1.2.1. Calculation...4
LITHIUM BATTERY CR123A SPECIFICATION
LITHIUM BATTERY CR123A SPECIFICATION Date: April 24, 2012 Approved by: Scotty Scott PANASONIC ENERGY CORPORATION OF AMERICA LITHIUM BATTERY DIVISION 1. Designation : CR123A 2. Nominal Voltage : 3 V 3.
Product Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
Use of Carbon Nanoparticles for the Flexible Circuits Industry
Use of Carbon Nanoparticles for the Flexible Circuits Industry Ying (Judy) Ding, Rich Retallick MacDermid, Inc. Waterbury, Connecticut Abstract FPC (Flexible Printed Circuit) has been growing tremendously
Power chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
LM78XX Series Voltage Regulators
LM78XX Series Voltage Regulators General Description Connection Diagrams The LM78XX series of three terminal regulators is available with several fixed output voltages making them useful in a wide range
DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
Standard Thick Film Chip Resistors
Standard Thick Film Chip Resistors FEATURES Stability R/R = 1 % for 00 h at 70 C 2 mm pitch packaging option for size Pure tin solder contacts on Ni barrier layer provides compatibility with lead (Pb)-free
LM35 Precision Centigrade Temperature Sensors
Precision Centigrade Temperature Sensors General Description Typical Applications The LM35 series are precision integrated-circuit temperature sensors, whose output voltage is linearly proportional to
FEATURES BODY DIA. MAX. Type M AWG 30: 0.0100 [0.254] Type C AWG 28: 0.0126 [0.320] Type T AWG 30: 0.0100 [0.254]
![FEATURES BODY DIA. MAX. Type M AWG 30: 0.0100 [0.254] Type C AWG 28: 0.0126 [0.320] Type T AWG 30: 0.0100 [0.254]](/thumbs/30/14198675.jpg "FEATURES BODY DIA. MAX. Type M AWG 30: 0.0100 [0.254] Type C AWG 28: 0.0126 [0.320] Type T AWG 30: 0.0100 [0.254]")
M, C, T NTC Thermistors, Coated FEATURES Small size - conformally coated. Wide resistance range. Available in 11 different R-T curves. DESCRIPTION Models M, C, and T are conformally coated, leaded thermistors
AC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
No. STSE-CW2163B <Cat.No.031110> SPECIFICATIONS FOR NICHIA WHITE LED MODEL : NSPW315BS NICHIA CORPORATION -0-
No. STSE-CW2163B SPECIFICATIONS FOR NICHIA WHITE LED MODEL : NSPW315BS -0- 1.SPECIFICATIONS (1) Absolute Maximum Ratings (Ta=25 C) Item Symbol Absolute Maximum Rating Unit Forward Current IF 30 ma Pulse
STAR PIPE Polska S.A ul. Gdyńska 51 62-004 Czerwonak tel. +48 61 667 41 20 fax +48 61 667 41 38
THE ALARM SYSTEM The base of the system consists of two non-insulated copper alarm wires with section equal to 1.5 mm2, located inside polyurethane foam parallel to the conduit pipe, offset in relation
TAIYO PSR-4000 AUS703
TAIYO PSR-4000 AUS703 LIQUID PHOTOIMAGEABLE SOLDER MASK Designed for Flip Chip Packaging Applications Halogen-Free (300ppm) Excellent Thermal and Crack Resistance Low Water Absorption RoHS Compliant Excellent
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760
For board-to-fpc. Narrow Pitch Connectors (0.35mm pitch)
For board-to-fpc Narrow Pitch Connectors (0.35mm pitch) S35 Series New FEATURES 1. 1.7 mm wide slim two-piece type connector Mated height 0.6 mm Smaller compared to A4F series Width: Approx. 44% down
WCAP-CSGP Ceramic Capacitors
A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance 1±0.2 Vrms, 1 khz ±10% C 15000 pf ± 10% Rated voltage Dissipation factor
Harmonic Drive acutator P r e c i s i o n G e a r i n g & M o t i o n C o n t r o l
D C S e r v o S y s t e m s RH Mini Series Total Motion Control Harmonic Drive acutator P r e c i s i o n G e a r i n g & M o t i o n C o n t r o l Precision Gearing & Motion Control DC SERVO ACTUATORS
Thin Film MELF Resistors
Thin Film MELF Resistors FEATURES MELF resistor with high power rating AEC-Q200 qualified Advanced metal film technology Best in class pulse load capability Intrinsic sulfur resistance Material categorization:
Power Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
PolyGard Carbon Monoxide CO Transmitter ADTX3 1110
PolyGard Carbon Monoxide CO Transmitter ADTX3 1110 DESCRIPTION CO transmitter including digital measurement value processing and temperature compensation for the continuous monitoring of the ambient air
Model CS 64 Mini-DIN Cable and Adaptor
Model CS 64 Mini-DIN Cable and Adaptor Page 1 of 9 Features Hi-Pro and NOAHlink compatible cable & Mini-DIN CS 64 Clip Module / NOAHlink Adaptor #1 Integrated Clip Module - Mini-DIN Cable Integrated NOAHlink
MICRO SWITCH EJF SERIES
MICRO SWITCH EJF SERIES FEATURES 1-piece spring mechanism design offering durable acute operation and nice touch feeling Heavy/Light operation force specifications High flux-tight structure High solder
How To Read A Pipe From A Sensor
Liquid Level Sensor Installation on pipes. Sensing by means electrostatic capacity and is not influenced by the color of the pipe or liquid. Available in 8 to mm dia. and to mm dia. models to enable sensing
Encoder. Switches. Series Size SMD
Piher is recognised as a world leader in custom controls and sensor solutions by the top Land Vehicle/Automotive and Appliance players. In this catalogue you will find a selection of the most prolific
Tape Wound, Split Core and Ebony Current Transformers
Tape Wound, Split Core and Ebony Current Transformers Table of contents Tape Wound Measuring and Protection Current Transformers 2 MR Series Measuring Range 3 PR Series Protection Range 4 Class PX Current
Adjustment functions for both span and shift have been incorporated
SENSORS FOR SERIES LED Type Wafer Alignment Sensor FX-0-F FT-F9 FD-F7 EX-F70/F60 M SH-7 FD-L4 M-DW The use of a safe LED light beam now allows for high precision detection with a resolution of 0!m (.8
Low Cost, Precision IC Temperature Transducer AD592*
a FEATURES High Precalibrated Accuracy:.5 C max @ +25 C Excellent Linearity:.15 C max ( C to +7 C) Wide Operating Temperature Range: 25 C to +15 C Single Supply Operation: +4 V to +3 V Excellent Repeatability
SLLP-5630-150-G PRODUCT DATASHEET. RoHS Compliant
PRODUCT DATASHEET SLLP-5630-150-G Table of Contents Features... 1 Applications 1 Characteristics.. 1 Typical Electro optical Characteristics Curves... 3 Mechanical Dimensions... 4 Carrier Tape Dimensions.....
NTC Thermistors, Radial Leaded and Coated
M, C, T NTC Thermistors, Radial Leaded and Coated FEATURES Small size - conformally coated Wide resistance range Available in 11 different R-T curves Available in point matched and curve tracking precision
3W RGB High Power LED
Features: Super high flux output and high luminance Designed for high current operation Low thermal resistance No UV Package Dimensions: Typical Applications Reading lights Portable flashlight Uplighters
0.84" x 2.00" Z-TRAUQ INC. Tel.: (450)226-6997 Fax: (450)226-5837 z-trauq@qc.aira.com SPLIT CORE CURRENT TRANSFORMER MODEL 1SP.
SPLIT CORE CURRENT MODEL 1SP 0.84" x 2.00" PAGE No 3-2 REV 18DEC00 UL 1015 LEAD WIRE, STANDARD LENGTH IS 36 E DIMENSIONS A = 0.84 MIN B = 2.00 MIN C = 3.31 MAX D = 3.09 MAX E = 0.61 MAX F = 0 MAX F C B
MCS 0402 AT, MCT 0603 AT, MCU 0805 AT, MCA 1206 AT - Precision www.vishay.com. Precision Thin Film Chip Resistors
Precision Thin Film Chip Resistors FEATURES Rated dissipation P 70 up to 0.4 W for size 1206 AEC-Q200 qualified Approved to EN 140401-801 Superior temperature cycling robustness Sulfur resistance verified
PV module safety qualification according to IEC 61730:2004 EN 61730:2007
PV module safety qualification according to IEC 61730:2004 EN 61730:2007 TÜV Rheinland Immissionsschutz und Energiesysteme GmbH Renewable Energies January 2009 Version 2009-01-22 Overview The long term
NEMA Magnet Wire Thermal Class Ratings
NEMA Magnet Wire Thermal Class Ratings How to Use Them, and How They are Derived Ron Beeckman Essex Group, Inc. Thermal Class of Magnet Wire is Based upon: Temperature Index: (ASTM): A number which permits
Thermal Adhesives Ther-O-Bond 1500
Products / Interface Materials / Adhesives Adhesives Bond 1500 Epoxy casting system for potting and encapsulation Bond 1600 Two part epoxy for bonding Bond 2000 Rapid cure acrylic adhesive bond High strength
Specification of 5 Wire Analog Touch Panel
Specification of 5 Wire Analog Touch Panel 5 WIRE ANALOG RESISTIVE TOUCH PANEL A. Application This specification applies to the 5 Wire Analog Resistive Touch Panel. B. Environmental Conditions 1. Operating
Application Note 142 August 2013. New Linear Regulators Solve Old Problems AN142-1
August 2013 New Linear Regulators Solve Old Problems Bob Dobkin, Vice President, Engineering and CTO, Linear Technology Corp. Regulators regulate but are capable of doing much more. The architecture of
3mm Photodiode,T-1 PD204-6C/L3
3mm Photodiode,T-1 Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high
No. : EX##-OMF0004 OPERATION MANUAL. SI unit EX12#-SMB1
No. : EX##-OMF0004 OPERATION MANUAL EX12#-SMB1 Contents 1. Safety instructions ------------------------------------------------------ P3 2. Notes ------------------------------------------------------