HILTI DX-KWIK & DX-BARDAGE
|
|
- Aubrey Reed
- 7 years ago
- Views:
Transcription
1 ATG Technical Approval with Certification Approval and Certification Body Fastening system HILTI DX-KWIK & DX-BARDAGE ATG 13/1824 Approval holder: Hilti Belgium nv Z.4 Broekooi 220 B-1730 Asse Tel.: +32 (0) Fax.: +32 (0) Website: Valid from 12/02/2013 until 11/02/2016 Belgian Construction Certification Association Rue d Arlon, Brussels info@bcca.be 1 Objective and scope of the technical approval This technical approval is based on the favourable evaulation of the product or system by an independent approval body designated by UBAtc asbl for a specific application. The outcomes of this evaluation are described in this approval document. This text identifies the product(s) used in the system and determines the expected performance of the product, in order to enable the production, use and maintenance of product(s) or system(s), produced as specified in this approval document. Technical approval is accompanied by regular inspections and adjustments in line with technical advancements, if such modifications are appropriate. Technical approval must be reviewed every three years. For technical approval to be renewed, the manufacturer must provide evidence at all times that he is continuing to take necessary steps to achieve the performance standards described in the approval document. This monitoring is vital in terms of ensuring that the product reliably conforms to this technical approval. This task is assigned to a certification body designated by the UBAtc. On-going checks and statistical interpretation of results enable the associated certification to achieve a high level of reliability. 2 Limitation of use The fastening elements which are subject to traction are located in the compression zone of the concrete. The use of the fastening elements is limited to the connections which, upon completion of the construction, are only subjected to stresses which are negligible if changes in temperature occur such as: fastening of profiled steel sheet with external thermal insulation (e.g. non-ventilated flat roof); fastening of profiled steel sheet such as this which adjoins the inner climate in the case of double facade covering with insulation in-between; fastening of the profiled steel sheet within a heated building (e.g. floors). 3 Durability - corrosion The durability of the connection depends on the application, the climate, the air pollution and the protection of the sheet to be fastened. The intended use only comprises fasteners and connections, which are not directly exposed to external weather conditions or moist atmospheres (see also information provided in the Hilti technical literature). The approval and certification for conformity to the approval are independent of tasks conducted individually. The contractor and architect remain fully responsible for the conformity of the preparation with the provisions contained in the specifiations.
2 To be fastened roof wall DX KWIK on CONCRETE C20/25 C 45/55 See PART I DX BARDAGE on STEEL Thickness 4 mm t 6 mm See PART II 4 Part I: DX-KWIK : System for fastening of profiled steel sheet to concrete 4.1Subject The DX-KWIK fastening system is designed to fasten profiled steel sheet onto concrete. This system combines drill fixing with direct fastening using powder-actuated fastening tool: after pre-drilling a small hole in the concrete, the fastening element is driven into position. The approval relates to the aforementioned system, the technology of the design and construction but not the quality of implementation on site nor the calculation of the number of necessary fastenings per plate Requirements Drills and bits Drill : for example: TE 4-A, TE 6-A, TE 7-A, TE 7 Bit : step shank drill bit TX-C 5/ Components of powder-actuated fastening system For the fastener NPH2-42 L15 fastening tool fastener guide piston Hilti DX 76 X-76-F-Kwik X-76-P-Kwik DX 76 PTR X-76-F-Kwik-PTR X-76-P-Kwik-PTR DX /S3 75/NPH2 4.2Materials 4.2.1Fastener Figure 1: Fastener NPH2-42 L15 Cartridge (powder loads) : Hilti 6.8/18M yellow: low/medium blue: medium Type : Shank : Galvanising : Dimensions : Washers : NPH2-42 L15 Hardened carbon steel (58 HRC), in accordance with NBN EN /AC Thickness 8-16 microns Shank Ø = 4.5 mm with a conical head Total length L = 46.8 mm (ballistic point) Galvanised steel, DC 01 in accordance with NBN EN Diameter 15 mm; thickness: 1 mm. All powder-actuated fastening tools are equipped with an energy regulation allowing adjustment of the driving energy (setting range from 1 to 4) Profiled steel sheet Steel quality: S280GD-S350GD in accordance with NBN EN Thickness: between 0.75 and 2.0 mm. The system of the covering (external sheet, form etc.) does not form part of the approval. 4.3Fabrication and control All elements which form part of the system (powder-actuated fastener, powder-actuated fastening tools and cartridges) are fabricated in the HILTI factories and checked systematically at each stage of the production process. Headquarters: S.A. HILTI, 9494 Schaan, Liechtenstein. ATG 13/1824-2/8
3 4.4Application The DX-KWIK fastening process consists of 2 steps: 4.4.1Pre-Drilling The pre-drilling consists of drilling a hole of Ø = 5 mm with a step shank drill bit with a length of 23 mm through the profiled steel plate into the concrete. Figure 2 : Pre-drilling of the hole The distances to be respected for the fastening are as follows (figure 5 for facades and figure 6 for roofs) : between the fastener and the edge: 80 mm between two fasteners where two profiled steel sheets are fastened to one support: 80 mm between two fasteners which are positioned orthogonally: 2 x 80 mm. The total maximum thickness of all the profile sheets, including their finishing layers, to be fixed amounts to 5 mm. Figure 5 : Facade covering The fastening In the second step the fastener is driven through the plate into the pre-drilled bore hole. Figure 3 : Position of fastener before driving k 80 mm; a 80 mm; d 160mm This pre-drilling on the one hand guarantees an anchoring of the nails and on the other hand limits the scattering of the anchoring values. Bearing structures: columns or girders in reinforced concrete. The dimensions of these must amount to at least 160 mm of width and 160 mm of depth in the fastening zone. These limits also apply for the I-shaped girders and hollow concrete slabs. The quality of the concrete can vary from C 20/25 to C 45/55, in accordance with the standard NBN B Figure 6 : Roof covering The reinforcement of the concrete (quantity, implementation) meets Belgian standards (standard series NBN EN ) regarding braces and concrete covering among other things. Hitting the prestressing cables or bars must be excluded. Fastening must satisfy the following conditions (Figure 4) : the fastener stand-off (the distance between fastener head and profile sheet) varies between 7.5 mm and 11 mm. both washers must be in contact with one another and with the profiled steel sheet. Figure 4 : Connection with DX-Kwik ATG 13/1824-3/8
4 4.5Characteristics The number of fastening points is specified using the allowable values stated in table 1 and table 2 (pag.4); for the specification of the allowable forces the Belgian standards and Eurocodes are used The values stated in the tables are based on a statistical analysis of 1,280 results. Table 2: Profiled steel sheet for roof covering (see PDF for diagram) Steel Allowable sheet types of thickness connection S Tensile strength Fz allowable Shear strength Fq allowable The safety factors applied are: S = 2 applied on the characteristic values which are the result of a static load. S = 1.3 applied on the characteristic values which are the result of a dynamic load. Two possibilities are analysed: the double facade covering, fastening of cassettes (see table 1) and profiled steel sheet for roof covering (see table 2). Table 1: Double walled facade covering (cassettes) Steel sheet thickness S Tensile strength Fz allowable Shear strength Fq allowable (mm) (kn) (kn) 0,75 a, b, c, d 1,80 1,20 0,88 a, b, c, d 2,10 1,50 1,00 a, b, c, d 2,40 1,80 1,13 a, b, c, d 2,70 2,20 1,25 a 3,00 2,50 1,50 a 3,00 3,00 1,75 a 3,00 3,00 2,00 a 3,00 3,00 2,50 a 3,00 3,00 Types of connection (mm) (kn) (kn) 0,75 1,30 1,20 0,88 1,50 1,50 1,00 1,70 1,80 1,13 1,90 2,20 1,25 2,10 2,50 1,50 2,50 3,00 1,75 2,50 3,00 2,00 2,50 3,00 2,50 2,50 3,00 Arrangement of the fastenings: For intermediate plate thicknesses it is necessary to take the allowable values for tension or shear from the sheet with the closest thickness, smaller than that of the element to be fastened. The allowable force is reduced as follows when both forces, tension and shear, occur at the same time. F Q all,red = 1 fastener in near the raised edge Distance between fastener and raised egde : < 75 mm. F Z all,red = = ratio of acting shear force to tension force 2 connections symmetrical in respect of the raised rib Distance between the fastener and the raised edge: 50 to 75 mm. Both fasteners must be at the same distance to the raised edge = ratio of acting tension force to shear force ATG 13/1824-4/8
5 Base material thickness t II [mm] Base material thickness t II [mm] 5 Part II : DX-BARDAGE : System for fastening profiled steel sheet to thin steel elements 5.1Subject The DX-BARDAGE fastening system is designed to fasten profiled steel sheet onto a thin walled steel profile. This approval relates to the aforementioned system, the technology of the design and construction but not the quality of the implementation on site, nor the calculation of the number of necessary fastenings of the sheet. 5.2 Materials 5.2.1Fastener Figure 7 : Fasteners X-ENP2K-20 L15 and X-ENP2K-20 L15 MX X-ENP2K-20 L15 All powder-actuated fastening tools are equipped with an energy regulation allowing adjustment of the driving energy (setting range from 1 to 4) Profiled steel sheet Steel quality: S280GD-S350GD in accordance with NBN EN Thickness: between 0.75 and 1.0 mm The system of the covering (plate, form etc.) does not form part of this approval. 5.3Fabrication and control All elements which form part of the system (nails, powderactuated fastening tools and cartridges) are fabricated in the HILTI factories and checked systematically at each stage of the production process. Headquarters: S.A. HILTI 9494 SCHAAN, LIECHTENSTEIN 5.4Application The DX-BARDAGE fastening system involves driving a powderactuated fastener through the profiled steel sheet into thin base material (thickness between 4 and 6 mm). Figure 8 : Application limit as function of the strength and thickness of the supporting steel X-ENP2K-20 L15 MX 6,0 Type : Shank : Galvanising : Dimensions : Washers : 5.2.2Requirements X-ENP2K 20 L15 (MX) Hardened carbon steel (56 HRC), in accordance with NBN EN /AC Thickness 8-16 microns Shank Ø = 3.7 mm with a conical head Total length L = 25.5 mm (ballistic point) Galvanised steel, DC 01 in accordance with NBN EN Diameter 15 mm; thickness: 1 mm. The components of powder activated fastening systems consist of a powder-actuated fastening tool, a fastener guide or magazine, a piston and powder cartridges: For the fastener X-ENP2K-20 L15 fastening tool fastener guide piston DX 76 PTR X-76-F-15-PTR X-76-P-ENP2K-PTR DX 76 X-76-F-15 X-76-P-ENP2K DX S1 75/ENP2K-L 5,5 5,0 4,5 Applicable range of base materials S 235 S 355 4, Cartridge recommendation: S 275 Base material strength R m [N/mm²] The following charts Figure 9 and Figure 10 show the selection of the cartridge (power-load) and the recommended tool energy setting for the respective powder-actuated tools. Fine adjustment of the tool energy setting may be required based on job-site trials. Figure 9 : Cartridge selection and tool energy setting for DX 76 PTR 6,0 DX 76 PTR with X-ENP2K-20 L15 MX For the fastener X-ENP2K-20 L15 MX fastening tool fastener magazine piston DX 76 PTR MX 76-PTR X-76-P-ENP2K-PTR DX 76 MX 76 X-76-P-ENP2K DX MX 75/ENP2K-L 5,5 5,0 4,5 Blue 4 Blue 4 Red 2 Cartridge (powder loads) : Hilti 6.8/18M green: Low yellow: low/medium 4, Base material strength R m [N/mm²] blue: medium red: medium high ATG 13/1824-5/8
6 Base material thickness t II [mm] Figure 10 : Cartridge selection and tool energy setting for DX 76 6,0 5,5 5,0 4,5 DX 76 or DX 750 with X-ENP2K-20 L15 (MX) Blue 2 Yellow 4 Green 4 4, Base material strength R m [N/mm²] Blue 4 / Red 2 Figure 11: Connection with DX-BARDAGE X-ENP2K-20 L15 (MX) Total thickness of the profile plates to be fastened must be less than 4 mm which means that total covering is only possible if the total thickness of covering and profile plate together does not exceed 4 mm. 5.5Characteristics The number of fastening points is specified by making use of the allowable load values stated in table 1 and table 2: for the stipulation of the allowable forces, Belgian Standards and Eurocodes are used. The values stated in the tables are based on a statistical analysis of test results where the plate thickness and steel quality of base material and finishing layers apply as parameters. The safety factor applied is: S 2, applied on the characteristic values which are the result of a static load. Two possibilities are analysed: double facade covering, fastening of cassettes (see table 3) and profiled steel sheet for roof covering (see table 4). Table 3: double facade covering, cassettes (base material 4 mm to 6 mm) For the X-ENP2K-20 L15 and the X-ENP2K-20 L15 MX, the required fastener stand-off (distance between fastener head and profile sheet) varies between 7 and 11 mm (Figure 11). The edge distances and spacings to be respected in the fastening are as follows (Figure 12) : Direction Distance between fasteners (mm) a 80 Distance to the edge of plate (mm) e > 20 e 75 Distance to the edge of profile (mm) Profile A B k k 10 Steel sheet thickness S Allowable tension force Fz Allowable shear force (mm) (kn) (kn) 0,75 1,25 1,20 0,88 1,50 1,40 1,00 1,90 1,55 Steel sheet thickness S Table 4 : Profiled steel sheet for roofs (base material 4 mm to 6 mm) Allowable types of connection Allowable tension force Fz FQ Allowable shear force FQ (mm) (kn) (kn) 0,75 a, b, c, d 1,80 1,70 0,88 a, b, c, d 2,10 2,00 1,00 a, b, c, d 2,70 2,20 Types of connection Figure 12 : Edge distances and spacing For intermediate plate thicknesses it is necessary to take the allowable values for tension or shear from the sheet with the closest thickness, smaller than that of the element to be fastened. ATG 13/1824-6/8
7 The allowable force is reduced as follows where both forces, tension and shear, occur at the same time: F Q all,red = F Z all,red = = ratio of acting shear force to tension force = ratio of acting tension force to shear force 6 Conditions A.Only the company referred to on the first page as the holder of an ATG and company/companies responsible for marketing the object of the approval may call for the application of this technical approval. B.This technical approval refers exclusively to the product or system, of which the trade name is mentioned in the header. Holders of a technical approval are not permitted to use the name of the UBAtc, its logo, the ATG brand, the text or approval number to demand the evaluation of products that fail to comply with the technical approval, and/or concerning products and/or systems and/or properties or characteristics that do not form the object of the technical approval. C.Information provided in any way for (potential) users of the product or system described in the technical approval (e.g. for clients, contractors, consultants, etc.) by the holder of the ATG or his designated and/or approved installation engineers must not contradict the content of the approval text or information referred to in the approval text. D.Holders of a technical approval are bound at all times to provide UBAtc asbl and the certification body designated by the UBAtc with prompt or prior notification of any adjustments made to primary materials and products, instructions for preparation, the manufacturing and construction and/or equipment process, so that they are able to judge whether it is necessary to adjust the technical approval. E.The copyright belongs to the UBAtc. ATG 13/1824-7/8
8 UBAtc asbl is an approval body and member of the European Union of Agrément for construction (UEAtc, see notified by the FPS Economy within the framework of Directive 89/106/EEC and member of the European Organisation for Technical Approvals (EOTA, see Certification bodies designated by UBAtc asbl operate in compliance with a system that is set to be accredited by BELAC ( This technical approval has been published by UBAtc, under the responsibility of the approval body BCCA, and based on favourable feedback from the specialist "" Group, issued on December 21 st In addition, the BCCA certification body has confirmed that the production process meets the conditions for certification and that a certification agreement was signed by the ATG holder. Date of issue: February 12 th For UBAtc, declaration of the validity of the approval process For the approval and certification body Peter Wouters, director Benny De Blaere, directeur This technical approval shall remain valid, provided the product, its manufacture and all processes that are appropriate for this purpose: - are maintained, in order to achieve, as a minimum, the performance levels defined in the approval document; - are continuously monitored by the certification body, which confirms that the certification continues to be valid; If these conditions are no longer met, the technical approval shall be suspended or withdrawn and the approval document shall be deleted from the UBAtc website. The validity and latest version of this approval document can be verified by consulting the UBAtc website ( or by directly contacting the UBAtc office. ATG 13/1824-8/8
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. Please refer to the publication in its entirety for complete details on this product
More informationEuropean Technical Approval ETA 13/0526
European Technical Approval ETA 13/0526 Trade Name Holder of the approval Website Generic type and use of construction product DOLCEA i3 PCIM S.A. Rue du Péquet 54 5590 Achene (Ciney) Belgium www.isoproc.eu
More informationHilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationHilti KWIK HUS-EZ I (KH-EZ I) Internally Threaded Carbon Steel Screw Anchor
Hilti KWIK HUS-EZ I (KH-EZ I) Internally Threaded Carbon Steel Screw Anchor Supplement to Hilti North American Product Technical Guide Volume 2: Anchor Fastening Technical Guide 2011 Edition 3.3. KWIK
More informationHUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast Anchor version HUS-A 6 Screw with hex head HUS-H 6 Screw with hex head HUS-I 6 Screw with hex head Benefits - Quick and easy setting - Low
More informationTrusted SECTION: 04 HILTI, INC. TULSA, Conformity! ICC-ES Evaluation. not specifically. Copyright 2015
0 ICC ES Report ICC ES (800) 42 6587 (562) 699 054 www.icc es.orgg 000 Most Widely Accepted and Trusted ESR 2269 Reissued 02/205 This report is subject to renewal 02/207. DIVISION: 0 00 00 CONCRETE SECTION:
More informationTechnical Application Document. Hilti HIT-RE 500-SD
Technical Application Document Technical Evaluation Report 3/10-649 Injection system for rebar connections Hilti HIT-RE 500-SD Subject to European Technical Approval ATE-09/0295 Holder of approval: HILTI
More informationEuropean Technical Assessment ETA-10/0153 of 10/06/2015
ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet ww.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011 of
More informationDESIGN OF SLABS. 3) Based on support or boundary condition: Simply supported, Cantilever slab,
DESIGN OF SLABS Dr. G. P. Chandradhara Professor of Civil Engineering S. J. College of Engineering Mysore 1. GENERAL A slab is a flat two dimensional planar structural element having thickness small compared
More informationEuropean Technical Approval ETA-09/0040
European Technical Approval ETA-09/0040 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and
More informationHilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationEuropeiskt Tekniskt Godkännande European Technical Approval
SITAC Box 553 SE 371 23 Karlskrona SWEDEN MEMBER OF EOTA Tfn.: +46-(0)10-516 63 00 Fax: +46-(0)455-206 88 E-mail: info@sitac.se Europeiskt Tekniskt Godkännande European Technical Approval Handelsnamn Trade
More informationConnection Solutions
Connection Solutions DESIGN BUILD SYSTEM Connection Solutions for Cold formed Steel Construction Complies with; AS/NZS 4600:2005 AISI S100:2007 AS/NZ 1397 ASTM A653 DESIGN & BUILD SYSTEM FRAMECAD Construction
More informationICC-ES Evaluation Report
ICC-ES Evaluation Report ESR-2369 Reissued May 1, 2010 This report is subject to re-examination in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council
More informationEuropean technical approval
Authorised and notified according to Article 10 of the Council Directive 89/ 106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating
More informationCERTIFICATE NAME OF PRODUCT MANUFACTURER PRODUCT DESCRIPTION CERTIFICATION PROCEDURE. No VTT C-6044-10 Date of issue 11.10.2010, Updated July 1, 2011
CERTIFICATE NAME OF PRODUCT No VTT C-6044-10 Date of issue 11.10.2010, Updated July 1, 2011 H-CONTROL REFLEX+ reflective insulating vapour control layer for roof and wall applications MANUFACTURER ACTIS
More informationHORIZONTAL INSTALLATION
THERMO/SOLAR Žiar s.r.o. MANUAL FOR INSTALLATION PV SUPPORTING FRAMES HORIZONTAL INSTALLATION Technical alternation reserved A1410 1 12/2014 CONTENT ORD.NO. PAGE Mounting information 3 Mounting, flat roof
More informationFLOORS REINFORCEMENT Shear Stud Connector for steel- concrete composite structures cold applied by pins
www.tecnaria.com FLOORS REINFORCEMENT Shear Stud Connector for steel concrete composite structures cold applied by pins HIGHPERFORMANCE FLOORS COMPOSITE STEEL AND CONCRETE STRUCTURES: STATIC AND ECONOMIC
More informationEuropean Technical Approval ETA 13/0384
European Technical Approval ETA 13/0384 Trade Name Holder of the approval Website Generic type and use of construction product Isobriq EU, Isobriq LE, Isobriq PA & Isobriq ZE Isobriq sa 49 Rue Slar 4801
More informationEuropean Technical Approval ETA-12/0500
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC
More informationGuidelines for Earthquake Bracing Residential Water Heaters
Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the
More informationTZ WEDGE ANCHOR FOR CRACKED AND UNCRACKED CONCRETE
SECTION 2.2 PAGE 1 / 9 l DESCRIPTION UCAN TZ torque controlled mechanical expansion wedge anchors have a Category 1 classification. They are used to resist static, wind and seismic tension and shear loads
More informationHVU with HAS/HAS-E rod adhesive anchor
HVU with HAS/HAS-E rod HVU with HAS/HAS-E rod adhesive anchor Mortar system Benefits Hilti HVU foil capsule HAS HAS-R HAS-HCR rod - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity
More informationDesign Manual to BS8110
Design Manual to BS8110 February 2010 195 195 195 280 280 195 195 195 195 195 195 280 280 195 195 195 The specialist team at LinkStudPSR Limited have created this comprehensive Design Manual, to assist
More informationEuropean Technical Approval ETA-08/0121
European Technical Approval - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and use of construction
More informationEuropean Technical Approval ETA-06/0259
European Technical Approval ETA-06/0259 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and
More informationHUS-H Screw Anchor. Technical data. Seismic design data. HUS-H Carbon steel screw anchor. HUS-H diameter 8, 10, 14. Seismic design data
Technical data HUS-H Carbon steel screw anchor HUS-H diameter 8, 10, 14 10 / 011 Version 011-10 1 HUS-H screw anchor seismic design data Anchor version Carbon steel screw Benefits - Quick and easy setting
More informationSAFETY FENCES, SAFETY BARRIERS AND PEDESTRIAN GUARDRAILS
SERIES NG 400 SAFETY FENCES, SAFETY BARRIERS AND PEDESTRIAN GUARDRAILS Contents Clause Title Page NG 401 Performance Criteria for Safety Fences and Safety Barriers 2 NG 402 Components for Safety Fences
More informationHUS-V Screw anchor. HUS-V Screw anchor. Basic loading data (for a single anchor) Mean ultimate resistance
HUS-V Screw anchor Anchor version HUS-V 8 / 10 Carbon steel concrete screw with hexagonal head Benefits - High productivity less drilling and fewer operations than with conventional anchors - Technical
More informationPRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE. By H P Gupta & D K Gupta
PRESENTATION ON REPAIR AND REHABILITATION OF BUILDINGS DAMAGED IN EARTHQUAKE By H P Gupta & D K Gupta DIFFERENT TYPES OF DAMAGES 1.Minor cracks 0.5 to 5 mm wide in load or non-load bearing walls 2.Major
More informationInstallation information. METTLER TOLEDO MultiRange DW150 / DW150T wall scale
Installation information METTLER TOLEDO MultiRange DW150 / DW150T wall scale DW150 / DW150T wall scale Contents Contents Page 1. Installation... 2 1.1 Preparatory work... 2 1.2 Installing the wall plates
More information0845 0098 980 www.nicholsonsts.com
0845 0098 980 www.nicholsonsts.com ROOFTRAK The IFP is revolutionising the way we fix things to roofs. Technical Director of a leading UK roofing system manufacturer The ROOFTRAK-IFP A revolutionary solution
More informationChapter 2 Basis of design and materials
Chapter 2 Basis of design and materials 2.1 Structural action It is necessary to start a design by deciding on the type and layout of structure to be used. Tentative sizes must be allocated to each structural
More informationHilti HIT-HY 200 with rebar
Hilti HIT-HY 200 Injection mortar system Benefits Hilti HIT- HY 200-A 500 ml foil pack (also available as 330 ml) Hilti HIT- HY 200-R 500 ml foil pack (also available as 330 ml) Static mixer rebar BSt
More informationHilti HIT-HY 150 MAX with rebar
Hilti HIT-HY 150 MAX Injection mortar system Hilti HIT- HY 150 MAX 330 ml foil pack (also available as 500 ml and 1400 ml foil pack) Static mixer rebar BSt 500 S Benefits - suitable for non-cracked and
More informationSubmittal Information
Wedge SPECIFIED FOR ANCHORAGE INTO CONCRETE Wedge anchs feature a stainless steel expansion clip, threaded stud body, nut and washer. Anch bodies are made of plated carbon steel, hot-dipped galvanized
More information(English language translation, the original version is in French language) SPIT HIT M. Société SPIT Route de Lyon F-26501 BOURG-LES-VALENCE France
Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 Tel. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 Autorisé et notifié conformément
More informationEuropeiskt Tekniskt Godkännande European Technical Approval
SITAC Box 553 SE 371 23 Karlskrona SWEDEN MEMBER OF EOTA Tfn.: +46-(0)10-516 63 00 Fax: +46-(0)455-206 88 E-mail: info@sitac.se Europeiskt Tekniskt Godkännande European Technical Approval ETA-12/0257 Handelsnamn
More informationEuropean Technical Approval ETA-10/0153
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC
More informationTimber Decks. Technical Note. March 2007
Timber Decks Technical Note. March 2007 This Technical Note contains general information for residential timber decks and floor frame structures for veranda s, patios etc which are exposed to the weather.
More informationDiameter. Swift Lift Round Recess Plug. Note: The diameter of the narrow recess plug is the same as the diameter of the round recess plug.
P-5 The P-5 is hot forged from carbon steel. The formed head provis spherical seating that the Lifting Eye engages, while a disc-shaped foot is embedd in the concrete. Due to its being a forged part, the
More informationEuropean Technical Approval ETA-10/0200
Deutsches Institut für Bautechnik Anstalt des öffentlichen Rechts Kolonnenstr. 30 B 10829 Berlin Germany Tel.: +49(0)30 787 30 0 Fax: +49(0)30 787 30 320 E-mail: dibt@dibt.de Internet: www.dibt.de Mitglied
More informationEuropean Technical Approval ETA-11/0024
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC
More informationMETHOD OF STATEMENT FOR STATIC LOADING TEST
Compression Test, METHOD OF STATEMENT FOR STATIC LOADING TEST Tension Test and Lateral Test According to the American Standards ASTM D1143 07, ASTM D3689 07, ASTM D3966 07 and Euro Codes EC7 Table of Contents
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More informationSERIES NG 1800 STRUCTURAL STEELWORK
MANUAL OF CONTRACT DOCUMENTS FOR HIGHWAY WORKS VOLUME 2 NOTES FOR GUIDANCE ON THE SPECIFICATION FOR HIGHWAY WORKS SERIES NG 1800 STRUCTURAL STEELWORK Contents Clause Title Page NG 1800 (08/14) General
More informationSPECIAL INSPECTION AND TESTING AGREEMENT INTERNATIONAL BUILDING CODE
Community Development Permit Services SPECIAL INSPECTION AND TESTING AGREEMENT INTERNATIONAL BUILDING CODE PROJECT NAME PROJECT ADDRESS PERMIT NUMBER CITY RECEIVED STAMP AND INITIALS Instructions: BEFORE
More informationSTRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM
Chapter 9 STRUCTURAL CONCEPT FOR LIGHT GAUGE STEEL FRAME SYSTEM 9.1 BACKGROUND Steel is widely used in the construction of multi-storey buildings. However, steel construction is seldom used and is traditionally
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the A325 structural bolt. Rev.
Structural Bolting ASTM A325 and ASTM A490 are the two U.S. standard structural bolts. When looking at the mechanical requirements of bolts it appears that an ASTM A325 and SAE J429 Grade 5 are identical
More informationStructural fire design Eurocode 5-1.2 Timber structures
Background and Applications Brussels, 18-20 February 2008 Dissemination of information workshop 1 Structural fire design Eurocode 5-1.2 Timber structures Jochen Fornather Austrian Standards Institute jochen.fornather@on-norm.at
More information1.2 Advantages and Types of Prestressing
1.2 Advantages and Types of Prestressing This section covers the following topics. Definitions Advantages of Prestressing Limitations of Prestressing Types of Prestressing 1.2.1 Definitions The terms commonly
More informationDESIGN OF SLABS. Department of Structures and Materials Engineering Faculty of Civil and Environmental Engineering University Tun Hussein Onn Malaysia
DESIGN OF SLABS Department of Structures and Materials Engineering Faculty of Civil and Environmental Engineering University Tun Hussein Onn Malaysia Introduction Types of Slab Slabs are plate elements
More information8 EXTRA LIGHT GRC SANDWICH ELEMENTS FOR ROOFING IN INDUSTRIAL BUILDINGS
8 EXTRA LIGHT GRC SANDWICH ELEMENTS FOR ROOFING IN INDUSTRIAL BUILDINGS MARICA DELLA BELLA and DIEGO CIAN Precompressi Centro Nord S.p.A., Italy SUMMARY: Secondary roofing elements, complementary to the
More informationANCHOR BOLTS FOR NUCLEAR POWER PLANT APPLICATIONS
ANCHOR BOLTS FOR NUCLEAR POWER PLANT APPLICATIONS EXPERIENCE FROM DESIGN AND CONSTRUCTION OF OLKILUOTO UNITS 2015-11-03 Kukkola Timo 2 OL1 AND OL2 CROSS-SECTION 3 OL1 AND OL2 OL1 and OL2 continuous improvement
More informationBETONYP building boards. The modern way of living.
BETONYP building boards The modern way of living. Tough for 30 years. Healthy, debarked pine wood and cement: the raw materials used to produce one of our most successful products for more than three decades.
More informationWelded Fabric. The CARES Guide to Reinforcing Steels Part 5. Installation of welded fabric on a major contract. 1.0 Introduction
Welded Fabric 1.0 Introduction Welded fabric, often referred to as mesh, is a machine welded grid arrangement of reinforcing bars or wires. It is covered by British Standard BS4483. This was revised in
More informationQuality Regulations for Profiles
Quality Regulations for Profiles September 2010 Quality Regulations for Profiles Page 2/42 Contents Preface... 4 1. Terms and Definitions... 5 1.1 Third parties... 5 1.2 Independent laboratories... 5 1.3
More informationInstallation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
More informationResidential Deck Safety, Construction, and Repair
Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the
More informationPRCP CE. Version 5.0 of 16 June 2013. Date of entry into force: 1 July 2013
npo Founded by SECO and BBRI PARTICULAR RULES FOR THE CERTIFICATION OF PRODUCTS AND PRODUCTION CONTROL SYSTEMS WITHIN DE FRAMEWORK OF THE EUROPEAN CONSTRUCTION PRODUCTS REGULATION N 305/2011 PRCP CE Version
More informationLEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code
LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900
More information(English language translation, the original version is in Czech language) DEWALT PTB-PRO. DeWalt Black-&-Decker Str. 40 65510 Idstein Germany
TECHNICKÝ A ZKUŠEBNÍ ÚSTAV STAVEBNÍ PRAHA, s.p. Prosecká 811/76a CZ-190 00 Praha 9 Tel.: +420 286 019 458 Internet: www.tzus.cz Authorised and notified according to Article 10 of the Council Directive
More informationSTANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES
ROOFING APPLICATION STANDARD (RAS) No. 117 STANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES Scope 1.1.
More informationCF-Mesa, CF-Light Mesa, CF-Flute, CF-Metl-Plank, CF-Striated, CF-Santa Fe, CF-Architectural Flat, CF...
Building Insulations - Walls and Ceilings (FM Approval Numbers 4411, 4651, 4880, 4881, 4882) Insulating materials may occur in building construction to reduce heat or sound transmission through a wall,
More informationDIVISION: 04 00 00 MASONRY SECTION: 04 05 19.16 MASONRY ANCHORS REPORT HOLDER: HILTI, INC. 7250 DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3342 Reissued 08/2015 This report is subject to renewal 08/2017. DIVISION: 04 00 00 MASONRY
More informationEuropean Technical Approval ETA-98/0001
European Technical Approval ETA-98/0001 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and
More information(English language translation, the original version is in French language) Injection system Hilti HIT-HY 150 MAX
Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 Autorisé et notifié conformément
More informationSDNS108 Dynamic response of a reinforced concrete slab leaned on 4 with dimensions subjected to a concentrated loading
Titre : SDNS108 - Réponse dynamique d'une dalle en béton a[...] Date : 31/05/2012 Page : 1/9 SDNS108 Dynamic response of a reinforced concrete slab leaned on 4 with dimensions subjected to a concentrated
More informationREHABILITATION OF THE FIGUEIRA DA FOZ BRIDGE
REHABILITATION OF THE FIGUEIRA DA FOZ BRIDGE A.Rito Proponte, Lda, Lisbon, Portugal J. Appleton A2P Consult, Lda, Lisbon, Portugal ABSTRACT: The Figueira da Foz Bridge includes a 405 m long cable stayed
More informationUnderstanding BS EN 771-3: Aggregate concrete masonry units
60 Charles Street, Leicester LE1 1FB Tel: 0116 253 6161 Fax: 0116 251 4568 Email: enquiries@cba-blocks.org.uk Website: www.cba-blocks.org.uk February 2006 Understanding BS EN 771-3: Aggregate concrete
More informationTECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE
TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION PART 8000 - PRECAST CONCRETE TABLE OF CONTENTS Item Number Page 8100 PRECAST CONCRETE CONSTRUCTION - GENERAL 8-3 8101 General
More informationMECHANICS OF SOLIDS - BEAMS TUTORIAL 1 STRESSES IN BEAMS DUE TO BENDING. On completion of this tutorial you should be able to do the following.
MECHANICS OF SOLIDS - BEAMS TUTOIAL 1 STESSES IN BEAMS DUE TO BENDING This is the first tutorial on bending of beams designed for anyone wishing to study it at a fairly advanced level. You should judge
More informationSECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for electrical
More informationDetailing of Reinforcment in Concrete Structures
Chapter 8 Detailing of Reinforcment in Concrete Structures 8.1 Scope Provisions of Sec. 8.1 and 8.2 of Chapter 8 shall apply for detailing of reinforcement in reinforced concrete members, in general. For
More informationEuropean Technical Approval ETA-04/0013
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC
More informationEnglish translation prepared by DIBt Original version in German language
Date: Reference: 14.05.2013 I 22-1.21.1-87/12 (73/13) English translation prepared by DIBt Original version in German language Approval number: Validity Z-21.1-1987 from: 14 May 2013 Applicant: Hilti Deutschland
More informationEuropean Technical Approval ETA-09/0169
UK CARES Pembroke House, 21 Pembroke Road, Sevenoaks, Kent, TN13 1XR, United Kingdom www.ukcares.com MEMBER OF EOTA European Technical Approval ETA-09/0169 Original version in English Trade name: Holder
More informationPART E SPECIFICATIONS
PART E SPECIFICATIONS Page 1 of 5 PART E - SPECIFICATIONS GENERAL E1. APPLICABLE SPECIFICATIONS, STANDARD DETAILS AND DRAWINGS E1.1 The City of Winnipeg Works and Operations Division Standard Construction
More informationSchöck Isokorb type KST User Selection Guide. Schöck Isokorb type KST Blindtext
Blindtext Schöck Isokorb type KST User Selection Guide Schöck Ltd 2-4 High Street Kidlington, Oxfordshire OX5 2DH Tel: 01865 290 890 Fax: 01865 290 899 E-mail: design@schoeck.co.uk Web: www.schoeck.co.uk
More informationEDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES OUTCOME 2 ENGINEERING COMPONENTS TUTORIAL 1 STRUCTURAL MEMBERS
ENGINEERING COMPONENTS EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES OUTCOME ENGINEERING COMPONENTS TUTORIAL 1 STRUCTURAL MEMBERS Structural members: struts and ties; direct stress and strain,
More informationChapter 3 Pre-Installation, Foundations and Piers
Chapter 3 Pre-Installation, Foundations and Piers 3-1 Pre-Installation Establishes the minimum requirements for the siting, design, materials, access, and installation of manufactured dwellings, accessory
More informationMultiPost-AP anchorage device
MultiPost-AP anchorage device MultiPost anchorage point Type 1 Fixing on reinforced concrete with large, 360 rotating stainless steel lifting eye for the simultaneous securing of max. 2 persons. This can
More informationDesign and Construction of Cantilevered Reinforced Concrete Structures
Buildings Department Practice Note for Authorized Persons, Registered Structural Engineers and Registered Geotechnical Engineers APP-68 Design and Construction of Cantilevered Reinforced Concrete Structures
More informationHUS-HR, CR Screw anchor, stainless steel
HUS-HR, CR Screw anchor, Anchor version HUS-HR 6 / 8 / 10 / 14 Stainless steel concrete Screw with hexagonal head HUS-CR 10 Stainless steel concrete screw with countersunk head Benefits - High productivity
More informationThe following sketches show the plans of the two cases of one-way slabs. The spanning direction in each case is shown by the double headed arrow.
9.2 One-way Slabs This section covers the following topics. Introduction Analysis and Design 9.2.1 Introduction Slabs are an important structural component where prestressing is applied. With increase
More informationAll Weather Hall. Efficient, multipurpose & quick to build
All Weather Hall Efficient, multipurpose & quick to build ALL WEATHER HALL www.deboer.com www.deboer.com ALL WEATHER HALL A flexible solution for a multitude of needs All Weather halls from De Boer provide
More information09/07/07 GLASSFIBER REINFORCED CEMENT (GRC) C. S. I. Spec 03500 Master Spec. 03 49 00 Page 1
C. S. I. Spec 03500 Page 1 PART 1 - GENERAL 1.01 SUMMARY:.01 Provide special glassfiber reinforced cement (GRC) shapes in accordance with the requirements of the contract documents..02 The installing contractor
More informationThe University of Birmingham (Live System)
The University of Birmingham (Live System) Behaviour of Structural Insulated Panels (SIPs) under both short-term and long-term loadings Yang, Jian; Rungthonkit, Prathan Document Version Author final version
More informationHUS-HR Stainless steel Concrete Screw A4 316. CE conformity. Corrosion resistance. European Technical Approval
HUS-HR screw anchor Anchor version Benefits HUS-HR Stainless steel Concrete Screw Quick and easy setting Low expansion forces in base materials Through fastening Removable Forged-on washer and hexagon
More informationEuropean Technical Approval ETA-08/0290
European Technical Approval ETA-08/0290 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and
More informationCavity Drain R20 is manufactured from1.0mm thick black high density polyethylene with studs approximately 20mm high.
CI/SfB Tn6 L6813 September 2013 RIW CAVITY DRAIN R20 R20 is manufactured from1.0mm thick black high density polyethylene with studs approximately 20mm high. Other systems are available for specific uses,
More informationBSF and BCC beam connections
No. 2512 Norwegian member of European Organisation for Technical Approvals, EOTA, and European Union of Agrément, UEAtc Issued: 11.09.2007 Revised: Valid until: 11.09.2012 Page: 1 of 5 BSF and BCC beam
More informationHow To Test A Wrap N Drain X Dampproofing System
National Research Council Canada Institute for Research in Construction Conseil national de recherches Canada Institut de recherche en construction CCMC 13094-R &&0& EVALUATION DIVISION 07111 REPORT Issued
More informationREPORT HOLDER: JENWEST ENTERPRISES LLC, DBA ADVANCED CONNECTOR SYSTEMS 321 SOUTH 1240 WEST #15 LINDON, UTAH 84042 EVALUATION SUBJECT:
0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 3635 Reissued 04/2016 This report is subject to renewal 04/2018. DIVISION: 03 00 00 CONCRETE
More informationSECTION 02845 GUARDRAILS
SECTION 02845 GUARDRAILS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals necessary and repair, replace or install all types of guardrails as specified herein
More informationSTANDARD OPEN PATIO COVER
STANDARD OPEN PATIO COVER BUILDING & SAFETY DIVISION 201 E. LA HABRA BLVD. LA HABRA, CA 90631 62-90-9710 Call Before You Dig 1-800-227-2600 PLEASE NOTE: This information Bulletin is made available to assist
More informationAsphalt Shingle Application Requirements
Alberta Allied Roofing Association Asphalt Shingle Application Requirements Section 1 Roof Decks 1.1 General Asphalt Shingles are not permitted to be installed directly over rigid insulation. When Asphalt
More informationLOAD-CARRYING CAPACITY OF AXIALLY LOADED RODS GLUED-IN PERPENDICULAR TO THE GRAIN
LOAD-CARRYING CAPACITY OF AXIALLY LOADED RODS GLUED-IN PERPENDICULAR TO TE GRAIN Prof. Dr.-Ing..J. Blaß, Dipl.-Ing. B. Laskewitz Universität Karlsruhe (T), Germany Abstract Glued-in rods have been used
More informationDraft Table of Contents. Building Code Requirements for Structural Concrete and Commentary ACI 318-14
Draft Table of Contents Building Code Requirements for Structural Concrete and Commentary ACI 318-14 BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318 14) Chapter 1 General 1.1 Scope of ACI 318
More informationKIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices
04000 Clamps Clamping devices 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 297 04010 Adjustable straps Tempered steel 1.1191 Black oxide finish nlm 04010-101 Suitable thrust
More information