Retro DAB Operation Guide

Transcription

1 Retro DAB Operation Guide Where to put your radio It is important that you consider carefully in advance where your radio will be situated and make sure that it is: * On a flat and stable surface * Within 1.4metres of a power socket (if using mains power) * Where you can fully extend the telescopic aerial * Away from bright sunlight or heat sources, such as a radiator * Not in a humid or very damp place such as a bathroom Setting up Connect the mains power lead into the socket on the back of the radio (DC IN) and plug the power adaptor into the mains power wall socket and switch on. Fully extend the radio aerial in a vertical position to obtain the maximum signal strength. When switching on for the first time, slide the power switch on the back of the radio to ON, Welcome to Digital Radio will be displayed. Then it will show the clock. If don t do further operation, the backlight will turn off and it enters into Standby Mode. Press button, it starts working. Functions 1. Mode: DAB (BAND Ⅲ 5A-13F), FM (87.5MHz-108MHz), IPOD, AUX_IN. 2. LCD:2x16 dots matrix; black background white fonts, negative LCD 3. Power Supply: AC INPUT V ; DC_OUTPUT 5V/2A 4. Output Power: 1.5W X2 5. STANDBY MODE Show Clock Keys and controls Standby Power ON or OFF Scan stations 3. PRE ---Store stations selected Scroll up Confirm and pause Scroll down 7. MODE ---Switch among different modes 8. INFO --- Information Alarm/snooze//sleep(multifunction button) 10. VOL- --- Decrease volume 11. VOL+ --- Increase volume DAB Operation 1. Connect the mains power lead into the socket on the back of the radio (DC in 5V) and plug the 1

2 power adaptor into the mains power wall socket and switch on. Switch to DAB mode, press MODE button repeatedly until the display shows Switch to DAB. Your radio will automatically begin to Quick SCAN DAB stations. A progressive bar will show the progress of the scan and the number of stations found during the scan will also be displayed. The stations scanned will be stored automatically when the scan is complete. The number of stations scanned will also be displayed at the upper right corner of the screen. If there s no signal, NO Signal will be shown. 2. The first station available will be played automatically. 3. You can press or button to switch among stations stored. 3. DAB scan modes,press shortly, it will Quick SCAN. Press it longer, it will FULL SCAN. 4. Press PREV and NEXT to scroll up or down to seek for your favorite stations. 5. Pess VOL+ or VOL- to adjust the volume. 6. To store the present station, press PRE button to activate store function. Preset Empty 1 will be displayed on lower line of the screen, and the number 1 will flash. Press and to scroll through the numbered preset locations (1-10), press button to store the station. Frequency will be displayed on the upper line. Preset x Stored will be shown on the lower line of the screen to indicate if you store the station successfully. 10 stations can be stored in total. To tune to a preset DAB station, press PRE button, then use and to scroll through the preset stations. Press ENTER button to confirm when you see the station you would like to listen. The radio will tune to that station and begin to play. 7. In DAB mode,the radio will synchronize with the time and date of the station. 8. In DAB mode,press INFO button, the information such as DLS, station name, time and date, frequency, bit rate, signal quality will be displayed. 9. In DAB mode,press button longer and enter into scan by manual. Press and button to scroll through channel 5A-13F and select the stations you would like to listen. Press button to confirm the channel, then press and to scroll through stations in this channel, press button enter into the station you selected. FM MODE operation 1. Press MODE button and switch into FM mode. At the first time FM frequency 87.5MHz. will be displayed on the screen. 2. Scan stations by manual, press or button shortly to adjust stations by 0.05MHZ until you get your favorite stations. 3. To autoscan stations, press button to search stations upward. If station signal is available, scan will stop automatically and play this station. Make press button longer, it will search stations downward. If station signal is available, scan will stop automatically and play this station. 4. If you know which frequency you going to listen to, you can press button to search stations upward quickly to get targeted frequency. It will stop scanning if you stop pressing and play the stations selected. 5. Press button to search stations downward quickly to get targeted frequency. It will stop scanning if you stop pressing and play the station selected. 6. To store the currently played station, make a long press of PRE button to activate store function. 2

3 Preset Empty 1 will be shown on the lower line of the screen, and number 1 will flash. Press or to select numbered location to store, then press to store the station. Frequency will be displayed on the upper line of the screen, and Preset x Stored will be displayed on the lower line. 10 stations can be stored in total. Press PRE to activate the function of listening stations stored. Then press or to select numbered locations. After pressing button to confirm, the station selected will be played. 7. In FM mode, press INFO button to display the information such as RDS, audio type, station frequency, time and date, signal quality, program text, program type. 8. In FM mode, press button to switch among audio types, you can select between Stereo and Mono. 9. In FM mode, when received RDS information, the radio will synchronize with the time and date of the station automatically. 10. Press VOL+ or VOL- to adjust volume. IPOD MODE OPERATION 1. Press MODE to switch into IPOD mode. If there s no ipod or iphone connected, ipod Disconnected will be displayed on the screen. Insert ipod or iphone into the 30 Pin connector, the screen will show ipod Connected and begin to display music in your ipod or iphone. 1. Press or to play previous or next track. 2. Press button to pause or play the track. 3. Press and hold button to search the current track using high speed rewind. It will stop and play again when you release the button. 4. Press and hold button to search the current track using high speed forward. It will stop and play again after you release the button. 5. Press VOL+ or VOL- to adjust volume. AUX-IN MODE OPERATION 1.Press MODE button to switch into AUX-IN mode, plug the aux-in cable into the 3.5mm AUX-IN jack at the back of the radio. It will play the music from external audio devices. 2.Press VOL+ or VOL- to adjust volume SYSTEM OPERATION 1.Factory reset. In working mode, make a long press of MODE button, Press Enter Key to Reset will be displayed on the screen. Then press to confirm the factory reset until System Reset OK shows up. 2. In working mode, make a long press of INFO button to check the software version. Alarm clock function This unit can set two alarms. In working or standby mode, make a short press of SNOOZE button. Press once shows ALARM1. Press twice shows ALARM2, alarm will ring 1 hour. It can wake up to DAB,FM,IPOD,BEEP Tone1, BEEP Tone2. SNOOZ lasts 5 minutes. 1. Setting the alarm in standby mode a. Make a short press of SNOOZE button to activate ALARM 1. After activated ALARM1, ALARM 1: BEEPER1 (the alarm type) is displayed on the upper line of the screen. OFF will be shown and 3

4 flashes on the lower line. Press or and choose ON. Then press to confirm your selection and enter into time setting, current time will be displayed on the left side of the screen. Alarm time 00:00 shows on the right side. Time setting is divided into hour setting and minute setting. It s 24 hour time system. Set the hour firstly, the 00 will keep flashing, then pess or and set hour quickly. Press to confirm and enter into minute setting. When 00 keeps flashing, then pess or and set minute quickly. Press to confirm and enter into alarm type selection by pressing or. You can choose from DAB,FM,IPOD,BEEP Tone1, BEEP Tone2 five modes. After your selection, press to confirm. Alarm setting is complete, the mark will show on the screen. When alarm rings, you can press button to close the alarm. The unit will enter into Standby mode and show clock. b. The alarm 2 setting is the same operation as the alarm Setting alarm in working mode a. You can set alarm in DAB,FM, IPOD,AUX four modes. Make a short press of SNOOZE button to activate alarm function. After activation, ALARM 1: BEEPER1 (alarm type) will be shown on the upper line of the screen. OFF will be displayed and flashes on the lower line. Press or button and choose ON. Press button to confirm the alarm function and enter into time setting. Current time shows at the left of the screen. Alarm time 00:00 shows at the right. Time setting is divided into hour and minute. It s 24 hour time system. Set the hour firstly, the left 00 will keep flashing, then pess or and set hour quickly. Make long press of those two buttons can set the time more quickly. Then press to confirm and enter into minute setting. When right 00 keeps flashing, then pess or and set minute quickly. Press to confirm and enter into alarm type selection by pressing or. You can choose from DAB, FM, IPOD, BEEP Tone1, BEEP Tone2 five modes. After your selection, press to confirm. alarm setting is complete. the mark will show on the screen. When alarm rings, you can press unit will enter into the previous mode before you perform alarm setting. b. The alarm 2 setting is the same operation as the alarm Alarm wake up: button to close the alarm. The a. when it wakes to DAB,after that it will play DAB program. If there s no DAB stations received, BEEP Tone1 will ring. b. when it wakes to FM,after that it will play FM program. c. when it wakes to IPOD, after that it will play ipod music directly. If no ipod is connected, BEEP Tone1 will replace it to ring automatically. At the time of alarm ring, whatever ipod music or BEEP sounds, take ipod away or insert ipod can close the alarm automatically. d. when it wakes to BEEP(BEEP Tone1, BEEP Tone2), the backlight will flash too. e. If two alarms are all set. When alarm 1 is ringing, alarm 2 is also waken, the alarm1 will turn off automatically. Only after the Alarm 1 is closed, can the Alarm 2 ring. 4. Alarm volume: The volume of alarm waking to DAB, FM, IPOD,BEEP Tone1, BEEP Tone2 is the half of the max volume. 4

5 5. Snooze: When alarm rings, press SNOOZE button and enter into snooze function. The snooze lasts 5 minutes. After 5 minutes, press SNOOZE button again to go on snoozing if needed. In the standby mode, two Z marks will be displayed at the right of the screen. But in working mode, there s no these marks. If ALARM 1enters into SNOOZEfunction, ALARM2 also enters into SNOOZE function after ring, the SNOOZE function of the ALARM 1will be closed automatically. There s only one ALARM can enter into SNOOZE. 6. SLEEP In working mode, make a long press of SNOOZE button to enter into sleep function setting, Sleep Timer will be displayed on the upper line of the screen, OFF displayed the lower right and keeps flashing. Then press or to select sleep time among 15min, 30min, 45min, 60min, 90min. After pressed to confirm, sleep time will be displayed on the upper right of the screen. If don t choose time, it will quit sleep setting automatically after 10 seconds. You can also press button to quit. 7. Battery powered mode: When using battery to supply power, the unit function and operation is the same as that of using DC power supply. But the unit won t charge your ipod/iphone.. when the battery has low power, there will be lower power mark showing on the LCD screen. When it is almost out of power, the unit will return to standby mode. Environmental Disposal Info: Electrical and electronic products displaying the crossed out wheeled bin symbol above must not be disposed of in general household waste. Take the product to a recycling facility that accepts electrical and electronic products. Check with your Local Authority for your nearest recycling centre. For further details, please contact View Quest 9-10 Mill Lane Alton Hampshire GU 342QG support@viewquest.co.uk 5