GRUNDFOS DATA BOOKLET CHI, CHIU. Multipurpose stainless steel pumps 50 Hz

Transcription

1 GRUNDFOS DATA BOOKLET CI, CIU Multipurpose stainless steel pumps 5 z

2 Contents General data Performance range, 5 z Page 3 Applications Page Pumped liquids Page Operating conditions Page Maximum operating pressure and liquid temperature Page Type keys Page 5 Codes Page 5 Pump, CI Page 6 Motor, CI Page 6 Materials, CI Page 6 Pump, CIU Page 7 Motor, CIU Page 7 Materials, CIU Page 7 Technical data CI Page 8 CIU Page 9 CI Page 1 CIU Page 11 CI 8 Page 1 CI 1 Page 13 CI, CIU Page 1 Curve conditions Page 1

3 General data CI, CIU Performance range, 5 z p [kpa] 6 6 CI, CIU 5 z 5 5 CI CI CI 8 CI CIU CIU Q [m³/h] Q [l/s] TM

4 General data CI, CIU Applications The CI and CIU pumps are primarily designed for industrial applications: Typical applications CI CIU Water treatment! " Industrial washing and dish-washing machines! " Pressure boosting of process water! eating and cooling in industrial processes! " Air-conditioning! " Airwashing, moisturization, humidification!! (softened water) Water supply and pressure boosting!! (potable water, also slightly chlorinated) Fertilizer/dosing systems! " Aquafarming! In addition, the CI, CIU pump is suitable for many specialized applications.! Recommended " Applicable Pumped liquids Thin, clean, non-aggressive and non-explosive liquids without solid particles or fibres. The pumps are able to pump liquids such as demineralised water, softened water, cleaning solutions, light oils and other light chemicals. When pumping liquids with a density and/or viscosity higher than that of water, motors with correspondingly higher outputs must be used, if required. Whether a pump is suitable for a particular liquid depends on a number of factors of which the most important are chloride content, p value, temperature and content of solvents, oils, etc. Operating conditions Liquid temperature: 15 C to +11 C Maximum ambient temperature: + C Maximum operating pressure: 1 bar Maximum inlet pressure is limited by maximum operating pressure. Maximum operating pressure and liquid temperature The actual operating range depends on the operating pressure, the pump type, the type of shaft seal, the pumped liquid and the liquid temperature. Shaft seal The shaft seal is to be selected on the basis of liquid temperature and type of liquid. For other liquids than water, the chemical resistance of the materials - incl. seal face, seat and rubber components of the shaft seal - must be taken into account. The following table shows available shaft seal types. CI CIU Pump type Shaft seal type BUBE BUBV BQQE BQQV BUUE BUUV Material Tungsten carbide (U)/ Carbon (B) Silicium carbide (Q)/ Silicium carbide (Q) Tungsten carbide (U)/ Tungsten carbide (U) Rubber parts EPDM (E) FKM (V) The following curves apply to clean water and watercontaining antifreeze additives. p [bar] p [bar] No shaft seal BUBE/BUBV t [ C] BQQE/BQQV BUUE/BUUV BUBE BQQE t [ C] TM

5 General data CI, CIU Type keys CI Example CI -5 - A -W-G - BUBE Type range Nominal flow rate [m 3 /h] Number of stages x 1 Code for pump version Code for pipe connection Code for materials excl. plastic and rubber parts Code for shaft seal CIU Example CI U - - A - W - G - E Type range Canned rotor type Nominal flow rate [m 3 /h] Number of stages x 1 Code for pump version Code for pipe connection Code for materials excl. plastic and rubber parts Code for rubber parts in pump Codes Example A -W -G -E -B U B E Pump version A Basic version Pipe connection W Internal thread B NPT thread Connecting thread, N special Materials Stainless steel parts in G 1.1 or similar class X Special version Code for rubber parts in pump, CIU E EPDM V FKM Shaft seal, CI B U B E B Rubber bellows seal U Q B E V Tungsten carbide (wolfram carbide) Silicon carbide Carbon EPDM FKM 5

6 General data CI Pump, CI orizontal, multistage centrifugal pump of the non selfpriming type with extended pump/motor shaft. The pump has a maintenance-free mechanical shaft seal with dimensions according to DIN 96. Compact pump unit with small physical dimensions, axial suction port and radial discharge port. Connections CI CI CI 8 CI 1 Axial suction port Rp 1 Rp 1¼ Rp 1½ Rp 1½ Radial discharge port Rp 1 Rp 1¼ Rp 1½ Rp 1½ Motor, CI The pump is coupled with a totally enclosed, fan-cooled Grundfos squirrel-cage motor. Standard voltages: 1 x - V, 5 z 3 x -/38-15 V, 5 z Enclosure class: IP 55 Insulation class: F Sound-pressure level: 6 db(a) Single-phase motors have a built-in thermal overload unit. Three-phase motors must be connected to a motor starter in accordance with local regulations. CI single-phase are also available with variable speed motors, type MGE. See seperate data booklet for CIE. Materials, CI Pos. Description Materials DIN W.-Nr. 1 Pump sleeve Stainless steel 1.1 Intermediate chamber/ guide vanes Stainless steel Impeller Stainless steel 1.1 Suction interconnector Stainless steel Spline shaft Stainless steel Cover plate Stainless steel Shaft seal faces BUBE, BUBV, BUUE, BUUV, BQQE and BQQV 8 Base plate Painted steel Motor flange 1 Ball bearing O-rings Cast iron Silumin EPDM or FKM EN-JL1 Sectional drawing, CI TM

7 General data CIU Pump, CIU orizontal, multistage centrifugal pump of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal. The bearings are lubricated by the pumped liquid. Compact pump unit with small physical dimensions, axial suction port and radial discharge port. Connections CIU CIU Axial suction port Rp 1 Rp 1¼ Radial discharge port Rp 1 Rp 1¼ Motor, CIU The motor is a -pole, asynchronous squirrel-cage motor. As the motor is cooled by the pumped liquid, the noise level is very low. Standard voltages: 1 x - V, 5 z 3 x - V, 5 z 3 x V, 5 z Enclosure class: IP Insulation class: Motor protection: Sound-pressure level: The pump requires an external contactor for motor protection, connected to built-in thermal overload unit. db(a) Materials, CIU Pos. Description Materials DIN W.-Nr. 1 Pump sleeve Stainless steel 1.1 Intermediate chamber Stainless steel Impeller Stainless steel 1.1 Suction interconnector Stainless steel Spline shaft Stainless steel Cover plate Stainless steel Thrust bearing Carbon MY 16 8 Spacer sleeve Stainless steel Base plate Painted steel Motor stool Aluminium Bearing plate Stainless steel Radial bearing Ceramic AI O 3 /SiC 13 Rotor ends 1-phase: Brass 3-phase: Copper 1 Rotor cladding Stainless steel Rotor can Stainless steel 1.1 O-rings EPDM or FKM Sectional drawing, CIU TM

8 Technical data CI p [kpa] CI 5 z ISO 996 Annex A Q [m³/h] P [kw] Q [l/s] Q [m³/h] [%] 6 TM 37 CI Dimensions and weights Rp L G 3/8" G 3/8" Dimensions [mm] Pump type 1-phase 3-phase Net weight [kg] L1 L1 CI CI CI CI CI ø8.5 1 TM 65 8 Electrical data 1 x - V, 5 z CI CI CI CI CI x -/38-15 V, 5 z CI /.8 9 CI / CI / CI / CI /

9 Technical data CIU p [kpa] CIU 5 z ISO 996 Annex A Q [m³/h] Q [l/s] P [kw] [%] Q [m³/h] TM1 977 Dimensions and weights Rp G3/8" G3/8" B1 B 5 Dimensions [mm] Pump type 1-phase Net weight [kg] B1 B CIU CIU CIU ø TM Electrical data 1 x - V, 5 z CIU CIU CIU x - V, 5 z CIU CIU CIU x V, 5 z CIU CIU CIU

10 Technical data CI p [kpa] CI 5 z ISO 996 Annex A Q [m³/h] Q [l/s] P [kw] Q [m³/h] [%] 6 TM 39 Dimensions and weights Rp 1 1/ L G 3/8" G 3/8" Dimensions [mm] Pump type 1-phase 3-phase Net weight [kg] L1 L1 CI CI CI CI CI ø8.5 1 TM Electrical data 1 x - V, 5 z CI CI CI CI CI x -/38-15 V, 5 z CI / 1. 9 CI / CI / CI /.3 87 CI /

11 Technical data CIU p [kpa] - CIU 5 z ISO 996 Annex A Q [m³/h] Q [l/s] P [kw] 1. [%] Q [m³/h] TM1 978 Dimensions and weights Rp1 1/ G3/8" G3/8" B1 B 5 Dimensions [mm] Pump type 1-phase Net weight [kg] B1 B CIU CIU CIU ø TM Electrical data 1 x - V, 5 z CIU CIU x -, 5 z CIU CIU CIU x V, 5 z CIU CIU CIU

12 Technical data CI 8 p [kpa] CI 8 5 z ISO 996 Annex A Q [m³/h] P [kw] Q [l/s] Q [m³/h] [%] 6 TM 351 Dimensions and weights Rp 1 1/ 5 G 3/8" L L1 139 D G 3/8" Dimensions [mm] Net weight Pump type L1 D [kg] 1-phase 3-phase CI CI CI CI CI ø8.5 1 TM 66 1 Electrical data 1 x - V, 5 z CI CI CI CI CI x -/38-15 V, 5 z CI / CI / CI / CI / CI /

13 Technical data CI 1 p [kpa] CI 1 5 z ISO 996 Annex A Q [m³/h] Q [l/s] P [kw] Q [m³/h] [%] 6 TM 355 Dimensions and weights Electrical data Rp 1 1/ 5 G 3/8" 1 x - V, 5 z CI L L1 139 D G 3/8" ø8.5 1 TM 66 1 CI CI CI x -/38-15 V, 5 z CI /.1 86 CI /.8 8 CI /.1 9 CI / CI / 6. 9 Dimensions [mm] Net weight Pump type L1 D [kg] 1-phase 3-phase CI CI CI CI CI

14 Technical data CI, CIU Curve conditions The guidelines below apply to the curves shown on the previous pages: 1. Tolerances to ISO 996, Annex A, if indicated.. Measurements were made with airless water at a temperature of C. 3. The curves apply to a kinematic viscosity of υ = 1 mm /s (1 cst).. The bold curves indicate the recommended performance range. The thin curves are only a guide. 5. Due to the risk of overheating, the pumps should not be used at a flow below the minimum flow rate. The curve below shows the minimum flow rate as a percentage of the nominal flow rate in relation to the liquid temperature. Qmin [%] t [ C] TM

15 15

16 Being responsible is our foundation Thinking ahead makes it possible Innovation is the essence V Repl. V GB Subject to alterations. GRUNDFOS A/S. DK-885 Bjerringbro. Denmark Telephone: