RIP Tombstone. Tombstone Ring Toss. YOU WILL NEED: Pegboards: 2 large squares 1 large circle. Instructions

Transcription

1 Instructions 1. Place your beads on the pegboards as shown. If you are using a clear pegboard, slide the actual-size pattern underneath it. 2. Ask an adult to fuse your designs see page 9 for further instructions. 3. Assembly: see page 10. RIP Tombstone YOU WILL NEED: Pegboards: 2 large squares 1 large circle Other: Heavy cardboard Glue or velcro Magenta - 54 Orange - 54 Creme - 36 Cheddar - 8 Prickly Pear - 54 Kiwi Lime - 54 Pastel Green - 28 Green - 14 Dark Green Turquoise - 54 Plum - 54 Purple - 54 Light Brown Brown Grey Dark Grey White - 58 Raspberry Pearl Stripe - 48 Fire Stripe - 48 Prickly Pear Pearl Stripe - 48 Cucumber Stripe - 84 Royal Blue Pearl Stripe - 48 Starry Nite Stripe - 48 Grape Stripe - 48 Monkey Stripe Zebra Stripe - 70 Silver Pearl Stripe Tombstone Ring Toss Game Create a spooky cemetery scene on a heavy cardboard surface using the Perler pieces and your favorite props. Glue or velcro your pieces in place. Determine where the player must stand to play. Assign points for successfully ringing the various objects: 10 points for either of the small tombstones 30 points for the skull tombstones 40 points for the RIP tombstone 50 points for either of the zombie hands alone 100 points for the tree monster top or arms Hit the gates at all, you lose all your points! 1

2 Skeleton Tombstone MAKE 2 all pieces Candles Creme Cheddar Grey Dark Grey White Zebra Stripe Silver Pearl Stripe 2

3 Small Tombstones MAKE 2 all pieces Zombie Hands Cheddar Pastel Green Green Dark Green Light Brown Grey Dark Grey Cucumber Stripe Zebra Stripe 3

4 Gate MAKE 2 Bead Color: 4

5 Tree Monster: The main part of the tree monster is created on two square pegboards assembled as shown at right. Cut out these two patterns and tape them together in the same way. Tree Monster Top Kiwi Lime Dark Brown Monkey Stripe 5

6 Tree Monster Trunk Dark Brown Monkey Stripe 6

7 Tree Monster Base Dark Brown Monkey Stripe 7

8 Tree Monster Arms Dark Brown Monkey Stripe 8

9 Rings: Using the same pattern, make 9 rings in the color combinations. The first color listed is for the outside, the second color is for the inside. Magenta Raspberry Pearl Stripe Orange Zebra Stripe Plum Grape Stripe Kiwi Lime Prickly Pear Pearl Stripe Purple Starry Nite Stripe MAKE 9 Turquoise Royal Blue Pearl Stripe Fire Stripe Prickly Pear Cucumber Stripe White Silver Pearl Stripe Fusing Instructions Only Adults Iron 1. Place your pegboard on a flat, heat-safe surface. 2. Set a household iron to the medium setting. Place ironing paper over the pegboard. In a circular motion, begin to iron the project. Do not press down with the iron. As the beads begin to fuse, you will see circles of the beads start to show through the paper. When ironed properly, the beads will still have an open center. Let the design cool. 3. Remove the paper and bead design from the peg board. Flip the design over to expose the non-fused side. Repeat step two. Let cool completely. NOTE: Beads need heat for about seconds per side to fuse evenly. Lift the paper occasionally to see how the beads are fusing. Depending on the size of the project, additional heating time may be required. DO NOT OVER-IRON the beads as it will make the centers of the beads close and can make the assembly you do with your project more challenging. 9

10 ASSEMBLY 1 Assemble the tombstones and gates by inserting the upright portion into the base. For the skull tombstone, also insert the candles into each base. For the small tombstones with the cross, insert the zombie hands into each base. On the tree monster, glue each of the arms to the trunk as indicated by the pink dots on the diagram. Insert the trunk into the base as shown. 2 Perler Beads and EKSuccess Brands are either registered trademarks or trademarks of Dimensions Crafts LLC and EK Success Ltd. respectively in the United States and/or other countries Dimensions Crafts LLC. All rights reserved. 10