Data Analysis Software TRAKPRO. Installation Guide

Transcription

1 Data Analysis Software TRAKPRO Data Analysis Software Installation Guide , Revision G November 2009

2

3 Copyright TSI Incorporated / / All rights reserved. Address TSI Incorporated / 500 Cardigan Road / Shoreview, MN / USA Fax No. (651) Limitation of Warranty and Liability (effective July 2000) Seller warrants the goods sold hereunder, under normal use and service as described in the operator's manual, shall be free from defects in workmanship and material for twenty-four (24) months, or the length of time specified in the operator's manual, from the date of shipment to the customer. This warranty period is inclusive of any statutory warranty. This limited warranty is subject to the following exclusions: a. Hot-wire or hot-film sensors used with research anemometers, and certain other components when indicated in specifications, are warranted for 90 days from the date of shipment. b. Parts repaired or replaced as a result of repair services are warranted to be free from defects in workmanship and material, under normal use, for 90 days from the date of shipment. c. Seller does not provide any warranty on finished goods manufactured by others or on any fuses, batteries or other consumable materials. Only the original manufacturer's warranty applies. d. Unless specifically authorized in a separate writing by Seller, Seller makes no warranty with respect to, and shall have no liability in connection with, goods which are incorporated into other products or equipment, or which are modified by any person other than Seller. The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE. TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES, INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE GOODS. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be brought against Seller more than 12 months after a cause of action has accrued. The goods returned under warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss. Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND LIABILITY, which contains the complete and exclusive limited warranty of Seller. This LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or its terms waived, except by writing signed by an Officer of Seller. Service Policy Knowing that inoperative or defective instruments are as detrimental to TSI as they are to our customers, our service policy is designed to give prompt attention to any problems. If any malfunction is discovered, please contact your nearest sales office or representative, or call TSI's Customer Service department at (800) (USA) or ( ) (International). iii

4 Trademarks TSI, TSI logo, DUSTTRAK, VELOCICALC, Q-TRAK, AEROTRAK, SIDEPAK, and TRAKPRO are trademarks of TSI Incorporated. Windows and Windows Vista are registered trademarks of Microsoft Corporation. iv

5 CONTENTS Introduction... 1 TRAKPRO Software Installation... 2 Driver Installation for DUSTTRAK II/DRX Aerosol Monitor For Windows 7 Operating System For Windows Vista Operating System For Windows XP Operating System Setup Radio Modems (optional accessory) Radio Modem Installation in Windows Vista Operating System Setup Radio Modem Configuration Software for Windows Vista Operating System Radio Modem Installation in Windows XP Operating System Setup Radio Modem Configuration Software for Windows XP Operating System USB Hardware Setup for SIDEPAK Monitor For Windows 7 Operating System For Windows Vista Operating System USB Bus Installation USB Port Installation For Windows XP Operating System USB Bus Installation USB Port Installation Install Verification USB Driver Setup for VELOCICALC /Q-TRAK 7565 Instruments. 65 For Windows 7 Operating System For Windows Vista Operating System For Windows XP Operating System Install Verification v

6 vi (page intentionally left blank)

7 Introduction The following guide has been developed for installing TRAKPRO Data Analysis software. The TRAKPRO software can be installed on Windows 7, Windows Vista, or XP operating systems. To install this software, you may need administrative rights on the computer. The Windows Mass Storage drivers, available only on Windows 7, Windows Vista, and XP are required for the AEROTRAK instruments. This version of TRAKPRO software was tested on Windows 7 Release Candidate and Windows Vista Business Edition. The USB install has been combined with the TRAKPRO software installation. As part of the software installation, the USB driver files are placed in the required directories. The MSCAL.OCX file for the calendar control is also added and registered to prevent error generation on selecting pump settings menu for SIDEPAK monitor with sampling pump. The install has been simplified so that you only need to click the Next > button on each dialog. The displayed screens are examples only and may differ from the screens on your computer. 1

8 TRAKPRO Software Installation Notes: If you installed a previous version of TRAKPRO software, it is highly recommended that you uninstall the previous version before installing the new version of TRAKPRO software. Install TRAKPRO software before connecting a TSI instrument to your PC. Inserting the TRAKPRO Installation CD in the computer CD-ROM or running the program setup.exe on the CD will start the setup process. (Note that if you don t have Microsoft.NET framework 2.0 installed on your computer, the installation process will install Microsoft.NET framework 2.0.) Windows operating system may seek permission from you to proceed. Windows 7 operating system may display a dialog box stating Do you want to allow the following program from an unknown publisher to make changes to this computer? Windows Vista operating system may display the following dialog. 2 TRAKPRO TM Data Analysis Software

9 1. Click on the Yes option for Windows 7 operating system or the Run Setup.exe option for Windows Vista operating system. 2. Click Next > button. TRAKPRO TM Installation Guide 3

10 3. Select I Agree and then click the Next > button. 4 TRAKPRO TM Data Analysis Software

11 4. This screen warns Windows 7 and Windows Vista operating system users to alter the installation directory from the suggested C:\Program Files\TSI\TrakPro to C:\TSI\TrakPro. 5. Click the Next > button. TRAKPRO TM Installation Guide 5

12 6. The Select Installation Folder screen provides a default location for the program to be installed. A different install directory can be selected by clicking the Browse button. You can also select to install this program for you or everyone who uses the computer. Then click Next > button. 6 TRAKPRO TM Data Analysis Software

13 7. The program is now ready to be installed. Click Next > button. 8. The installation begins. TRAKPRO TM Installation Guide 7

14 8 TRAKPRO TM Data Analysis Software

15 9. Once completed, the following screen is displayed. Click the Close button. At this point, you have installed TRAKPRO software and the USB driver files, and registered the calendar control file. TRAKPRO TM Installation Guide 9

16 For a better visual view, set your computer s appearance display property to Windows XP operating system style. 10 TRAKPRO TM Data Analysis Software

17 Or set the theme property to Windows XP operating system. TRAKPRO TM Installation Guide 11

18 Driver Installation for DUSTTRAK II/DRX Aerosol Monitor After the successful completion of TRAKPRO software installation and program setup, you can power-on the DUSTTRAK DRX instrument. Once the power-on operation is complete (approximately 1 minute), connect the USB cable from the instrument to a free USB port. For Windows 7 Operating System 1. The computer will display an Installing device driver software box at the bottom right of your screen. 2. Once the driver is successfully installed, a popup message will appear indicating that the NDIS drivers were successfully installed. 12 TRAKPRO TM Data Analysis Software

19 3. To verify the USB driver installation, display the Device Manager and the following screen will be displayed: 4. Expand the Network adapters tree and confirm the entry for TSI USB Remote NDIS The entry should not have a yellow exclamation mark. If there is an error, select the entry, right-click and select the Update Driver in the popup box. Repeat the USB install process following the on-screen directions. TRAKPRO TM Installation Guide 13

20 For Windows Vista Operating System 1. The computer will display New hardware found box at the bottom right of your screen. The following screen will be displayed: 2. You may be asked for permission to continue at this point. If so, click the Continue button. 3. Click Locate and install driver software (recommended).the NDIS INF file and the NDIS drivers were installed on the hard drive in their correct respective folders and the New Hardware Found wizard will find them. 14 TRAKPRO TM Data Analysis Software

21 4. When the following screen is displayed, click Install this driver software anyway. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows Vista operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 5. Once the driver is successfully installed, a popup message will appear indicating that the NDIS drivers were successfully installed. 6. Disconnect the USB Cable to the DUSTTRAK DRX monitor and turn the DUSTTRAK DRX monitor off. Restart the instrument, wait one (1) minute, and reconnect the USB cable. 7. The DUSTTRAK DRX monitor is now ready to be connected to the TRAKPRO software application. TRAKPRO TM Installation Guide 15

22 8. To verify the USB driver installation, go to Start Computer, right-click and click Manage from the menu. The following screen will be displayed: 16 TRAKPRO TM Data Analysis Software

23 9. Double-click the Device Manager and the following screen will be displayed: 10. Expand the Network adapters tree and confirm the entry for TSI USB Remote NDIS The entry should not have a yellow exclamation mark. If there is an error, select the entry, right-click and select the Update Driver in the popup box. Repeat the USB install process following the on-screen directions. TRAKPRO TM Installation Guide 17

24 For Windows XP Operating System 1. The computer will display New hardware found box at the bottom right of your screen. The following steps will guide you through the USB driver installation 2. Select No, not this time and then click Next. The following screen will be displayed: 18 TRAKPRO TM Data Analysis Software

25 3. Select the Install the software automatically (Recommended) option and then click Next. TRAKPRO TM Installation Guide 19

26 4. When the following screen is displayed, click the Continue Anyway button: Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows XP operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 20 TRAKPRO TM Data Analysis Software

27 5. Once the driver is successfully installed, the following screen will be displayed: 6. Click Finish. The DUSTTRAK DRX is now ready to be connected to the TRAKPRO software application. Note: If there are no errors and the Finish button has not been enabled after a few minutes, check if the USB cable is connected and unplug it. Restart the DUSTTRAK DRX monitor and reconnect the USB cable. TRAKPRO TM Installation Guide 21

28 7. To verify the USB driver installation, go to My Computer, rightclick the Properties Select Hardware tab. The following screen will be displayed: 22 TRAKPRO TM Data Analysis Software

29 8. Double click the Device Manager button and the following screen will be displayed: 9. Expand the Network adapters tree and confirm the entry for TSI USB Remote NDIS The entry should not have a yellow exclamation mark. If there is an error, select the entry, right-click and select the Update Driver in the popup box. Repeat the USB install process following the on-screen directions. TRAKPRO TM Installation Guide 23

30 Setup Radio Modems (optional accessory) Wireless Radio Modems are available for remote logging and data acquisition. One Radio Modem is connected to the DUSTTRAK monitor, and the other is connected to the user s computer (Base Station Radio Modem). Follow these software installation steps for each radio modem. Radio Modem Installation in Windows Vista Operating System 1. Insert the Radio Modem CD into your CD-ROM. Connect the Radio Modem to your PC through a USB cable. 24 TRAKPRO TM Data Analysis Software

31 2. Select Continue. 3. Click Next. Wait for the following screens to appear. TRAKPRO TM Installation Guide 25

32 4. Select Install this driver software anyway. 26 TRAKPRO TM Data Analysis Software

33 5. The High Speed Serial Converter drivers are now installed. Click Close. TRAKPRO TM Installation Guide 27

34 After the first round of installation, a new Hardware Wizard screen will popup. Follow these steps to install the COM port driver. 1. Click Next to continue. Wait for following screens to appear. 28 TRAKPRO TM Data Analysis Software

35 2. Select Install this driver software anyway. 3. The Serial Port drivers are now installed. Click Close. TRAKPRO TM Installation Guide 29

36 Setup Radio Modem Configuration Software for Windows Vista Operating System 1. Insert the Radio Modem CD into your CD-ROM if it is not there already. If the CD auto plays and displays the Product Documentation & Software form, select Install X-CTU Software. If the Product Documentation & Software form does not appear, use Windows Explorer to navigate the CD to CD Drive Letter Software X-CTU\ and run the install program Setup_xctu.exe. 2. Select Allow. 30 TRAKPRO TM Data Analysis Software

37 3. Click Next on the popup screen. TRAKPRO TM Installation Guide 31

38 4. Select I Agree and click Next. 5. To install in default folder, click Next. To install in a different folder, enter folder path or click Browse, click Next. 32 TRAKPRO TM Data Analysis Software

39 6. Confirm installation and click Next to start the installation. TRAKPRO TM Installation Guide 33

40 7. Optional Select No. 34 TRAKPRO TM Data Analysis Software

41 8. Click Close when installation is finished. TRAKPRO TM Installation Guide 35

42 To verify the Radio Modem driver installation, go to Start Computer, right-click, and select Manage from the menu. The following screen will be displayed. Double-click the Device Manager and the following screen will be displayed: 36 TRAKPRO TM Data Analysis Software

43 Radio Modem Installation in Windows XP Operating System 1. Insert the Radio Modem CD into your CD-ROM. Connect the Radio Modem to your PC through a USB cable. Note: For now, ignore the auto play MaxStream Product Documentation & Software Screen. 2. Click Next on the popup screen. TRAKPRO TM Installation Guide 37

44 3. Select the first device and click Next when prompted. When Windows prompts for driver installation, click Continue Anyway. 38 TRAKPRO TM Data Analysis Software

45 4. Click No if you are asked to replace newer FTDI files. 5. Click Finish when you finish installation. 6. After the first round of installation, a new Hardware Wizard screen will popup. Follow these steps to install the COM port driver. TRAKPRO TM Installation Guide 39

46 7. Click Next and Continue Anyway to continue. 40 TRAKPRO TM Data Analysis Software

47 8. Click No if you are asked to replace newer FTDI files. TRAKPRO TM Installation Guide 41

48 9. Click Finish after the serial port adapter is installed. 42 TRAKPRO TM Data Analysis Software

49 Setup Radio Modem Configuration Software for Windows XP Operating System 1. Insert the Radio Modem CD into your CD-ROM, the X-CTU software startup screen will come up automatically, click Install X-CTU software button on the startup screen. 2. Click Next on the popup screen. TRAKPRO TM Installation Guide 43

50 3. Select I Agree and click Next. 44 TRAKPRO TM Data Analysis Software

51 4. To install in default folder, click Next. To install in a different folder, enter folder path or click Browse, click Next. TRAKPRO TM Installation Guide 45

52 5. Confirm installation and click Next to start the installation. 46 TRAKPRO TM Data Analysis Software

53 6. Click Close when installation is finished. To verify the Radio Modem driver installation, Navigate to Control Panel System Hardware Device Manager Ports. Check for the USB Serial Port. TRAKPRO TM Installation Guide 47

54 48 TRAKPRO TM Data Analysis Software

55 USB Hardware Setup for SIDEPAK Monitor As part of the TRAKPRO Data Analysis software installation, the USB driver files are placed in the required directories. When you insert the SIDEPAK USB cable into one of the USB ports, the screens in this section will be displayed. The USB hardware setup procedure is different for Windows Vista and XP so it is important to refer to the instructions for the specified operating system. The following screens appear once you plug the SIDEPAK aerosol monitor USB cable into the computer. The USB install has two parts: 1. Install USB bus 2. Install USB port The screens for the bus and port installation are similar. The install has been simplified so that you only need to click the Next > button on each dialog. For Windows 7 Operating System This section explains how to install the USB bus and port for Windows 7 operating system. 1. The computer will display Installing device driver software box at the bottom right of your screen. TRAKPRO TM Installation Guide 49

56 2. Once the driver is successfully installed, a popup message will appear indicating that the NDIS drivers were successfully installed. For Windows Vista Operating System This section explains how to install the USB bus and port for Windows Vista operating system. USB Bus Installation 1. Select the Locate and install driver software (recommended) option. 2. You may be asked for permission to continue at this point. If so, click the Continue button. 50 TRAKPRO TM Data Analysis Software

57 3. Click the Install this driver software anyway button. The setup will start executing. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows Vista operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. You now need to install the USB port. TRAKPRO TM Installation Guide 51

58 USB Port Installation 1. Select the Locate and install driver software (recommended) option. 2. You may be asked for permission to continue at this point. If so, click the Continue button. 52 TRAKPRO TM Data Analysis Software

59 3. Click the Install this driver software anyway button. The setup will start executing. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows Vista operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 4. Once installed, the following message appears: TRAKPRO TM Installation Guide 53

60 For Windows XP Operating System This section explains how to install the USB bus and port for Windows XP operating system. USB Bus Installation 1. Select the default option Install the software automatically and click the Next > button. 54 TRAKPRO TM Data Analysis Software

61 2. A search for the correct driver starts. TRAKPRO TM Installation Guide 55

62 3. Click Continue Anyway button. The setup will start executing. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows XP operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 56 TRAKPRO TM Data Analysis Software

63 4. Once installed, the final information screen is displayed. Click the Finish button. You now need to install the USB port. TRAKPRO TM Installation Guide 57

64 USB Port Installation 1. Select the default option Install the software automatically and then click Next > button. 58 TRAKPRO TM Data Analysis Software

65 2. A search for the correct driver will start. TRAKPRO TM Installation Guide 59

66 3. Click Continue Anyway button. The setup will start executing. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows XP operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 60 TRAKPRO TM Data Analysis Software

67 4. Once installed, the final information screen is displayed. Click the Finish button. TRAKPRO TM Installation Guide 61

68 Install Verification 1. To verify the USB installation, select Start Control Panel System Hardware Device Manager Universal Serial Bus controllers. If the USB High Speed Serial Converter is listed, the install was successful. There should not be a yellow question mark on the listing. Exit all dialogs. 62 TRAKPRO TM Data Analysis Software

69 2. Run the TRAKPRO software application by double-clicking the desktop icon. Select SidePak Sampling Pump or SidePak Aerosol Monitor as the active device. 3. Select Instrument Setup menu and then select the Communications entry. The following screen is displayed. Confirm the correct device is selected. TRAKPRO TM Installation Guide 63

70 4. For the SIDEPAK pump, select Instrument Setup menu and then select the Pump Setup entry. A screen similar to the following screen is displayed. This confirms that the calendar control file was successfully installed and registered. In the Pump Clock Time section, verify the correct time is displayed and the pump time can be updated. 64 TRAKPRO TM Data Analysis Software

71 USB Driver Setup for VELOCICALC /Q-TRAK 7565 Instruments As part of the TRAKPRO Data Analysis software installation, the USB driver files are placed in the required directories. See also USB Hardware Setup for SidePak Monitor. For Windows 7 Operating System This section explains how to install the USB drivers for the VELOCICALC \Q-TRAK Model 7565 instruments on Windows 7 operating system. The following screens appear once you plug the VELOCICALC / Q-TRAK Model 7565 instruments USB cable into the computer. 1. The computer will display an Installing device driver software box at the bottom right of your screen. 2. Once the driver is successfully installed, a popup message will appear indicating that the USB drivers were successfully installed. TRAKPRO TM Installation Guide 65

72 For Windows Vista Operating System This section explains how to install the USB drivers for the VELOCICALC \Q-TRAK Model 7565 instruments on Windows Vista operating system. The following screens appear once you plug the VELOCICALC / Q-TRAK Model 7565 instruments USB cable into the computer. 1. Select the Locate and install driver software option. 2. You may be asked for permission to continue at this point. If so, click the Continue button. 3. Click the Install this driver software anyway button. The setup will start executing. 66 TRAKPRO TM Data Analysis Software

73 Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows Vista operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 4. Once installed, the following message appears: TRAKPRO TM Installation Guide 67

74 For Windows XP Operating System This section explains how to install the USB drivers for the VELOCICALC /Q-TRAK Model 7565 instruments on Windows XP operating system. 1. The following screen appears once you plug the VELOCICALC / Q-TRAK Model 7565 instruments USB cable into the computer. 2. The install has been simplified so that you only need to click the Next > button on each dialog. 3. Select Install the software automatically, then click Next > button. Windows will automatically install the USB driver. A search for the correct driver will start. 68 TRAKPRO TM Data Analysis Software

75 TRAKPRO TM Installation Guide 69

76 4. If you encounter the following screen, click Continue Anyway button. The setup will start executing. Note: Although this USB driver has not been tested by Microsoft for compatibility with Windows XP operating system, it has been extensively tested by TSI Incorporated. The installation of this USB driver should not harm your computer system. 70 TRAKPRO TM Data Analysis Software

77 5. Once completed, the final information screen is displayed. Click the Finish button. At this point, you have installed the USB driver. You are ready to use TRAKPRO software with the supported instruments. TRAKPRO TM Installation Guide 71

78 Install Verification To verify the USB driver installation, select Start Control Panel System Hardware Device Manager Universal Serial Bus controllers. If your instrument (e.g., TSI Air Velocity Meter) is listed, the install was successful. There should not be a yellow question mark on the listing. Exit all dialogs. 72 TRAKPRO TM Data Analysis Software

79 TSI Incorporated 500 Cardigan Road, Shoreview, MN U.S.A USA Tel: Website: UK Tel: tsiuk@tsi.com Website: France Tel: tsifrance@tsi.com Website: Germany Tel: tsigmbh@tsi.com Website: India Tel: tsi-india@tsi.com China Tel: tsibeijing@tsi.com Singapore Tel: tsi-singapore@tsi.com Contact your local TSI Distributor or visit our website for more detailed specifications. P/N Rev G Copyright 2009 by TSI Incorporated Printed in U.S.A.