A. This Section includes surface preparation, painting, and finishing of exposed interior and exterior items and surfaces.

Transcription

1 SECTION PAINTING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section SUMMARY A. This Section includes surface preparation, painting, and finishing of exposed interior and exterior items and surfaces. 1. Surface preparation, priming, and finish coats specified in this Section are in addition to shop-priming and surface treatment specified under other Sections. B. Paint exposed surfaces, whether or not colors are designated in schedules, except where a surface or material is specifically indicated not to be painted, or is to remain natural. Where an item or surface is not specifically mentioned, paint the same as similar adjacent materials or surfaces; verify with Architect. If color or finish is not designated, the Architect will select from standard colors or finishes available. 1. Painting includes field-painting air outlets and louvers exposed bare, and covered pipes and ducts (including color coding), hangers, exposed steel and iron work, and primed metal surfaces of mechanical and electrical equipment as specified in Division 15 and 16, respectively. 2. Painting includes field-painting of roof flashing and roof mounted equipment, ductwork, and supports exposed to view, regardless of factory finish. C. Painting is not required on prefinished items, finished metal surfaces, concealed surfaces, operating parts and labels, unless specifically indicated.

2 1. Prefinished items not to be painted include metal toilet enclosures, acoustic materials, architectural woodwork and casework, doors, elevator entrance doors and frames, elevator equipment, finished mechanical and electrical equipment, light fixtures, switchgear, and distribution cabinets. 2. Concealed surfaces not to be painted include wall or ceiling surfaces in foundation spaces, furred areas, utility tunnels, pipe spaces, duct shafts, and elevator shafts. 3. Finished metal surfaces not to be painted include anodized aluminum, stainless steel, chromium plate, copper, bronze, brass, and Kynar/Hylar 500 finishes. 4. Operating parts not to be painted include moving parts of operating equipment such as valve and damper operators, linkages, sensing devices, motor, and fan shafts. 5. Labels: Do not paint over Underwriters Laboratories, Factory Mutual or other code-required labels or equipment name, identification, performance rating, or nomenclature plates. D. Related Sections: The following Sections contain requirements that relate to this Section: metal. 1. Division 5 Section "Metal Fabrications" for shop-priming ferrous 1.03 SUBMITTALS 2. Division 8 Section "Standard Steel Doors and Frames" for shoppriming steel doors and frames. 3. Division 9 Section "Wall Coverings" for substrate sealer under wall coverings. A. Product data for all components of each paint system specified. Provide the manufacturer's technical information including label analysis and instructions for handling, storage, and application of each material proposed for use. List each material and cross-reference the specific coating, finish system, and application. Identify each material by the manufacturer's catalog number and general classification. Provide certification by the manufacturer that products supplied comply with local regulations controlling use of volatile organic compounds (VOCs).

3 B. Samples for Verification Purposes: Provide two 12" x 12" square samples of each color and material to be applied with texture to simulate actual conditions on representative samples of the actual substrate. 1. Provide stepped samples defining each separate coat including block fillers and primers. Use representative colors when preparing samples for review. Resubmit until required sheen, color, and texture are achieved. 2. Provide a list of material and application for each coat of each sample. Label each sample as to location and application. 3. Submit samples on the following substrates for the Architect's review of color and texture only: 1.04 QUALITY ASSURANCE a. Stained or Natural Wood: Provide two 4-by-8-inch samples of natural and stained wood finish on actual wood surfaces. b. Ferrous Metal: Provide two 4-inch-square samples of flat metal and two 8-inch-long samples of solid metal for each color and finish. A. Applicator Qualifications: Engage an experienced applicator who has completed painting system applications similar in material and extent to those required for the Project, with a construction record of successful inservice performance. B. Single-Source Responsibility: Provide primers and undercoat paint produced by the same manufacturer as the finish coats DELIVERY, STORAGE, AND HANDLING A. Deliver materials to the job-site in the manufacturer's original, unopened packages and containers bearing manufacturer's name and label, and the following information: 1. Product name or title of material. 2. Product description (generic classification or binder type). 3. Manufacturer's stock number and date of manufacture. 4. Contents by volume, for pigment and vehicle constituents. 5. Thinning instructions. 6. Application instructions. 7. Color name and number.

4

5 B. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature of 45 deg. F (7 deg. C). Maintain containers used in storage in a clean condition, free of foreign materials and residue JOB CONDITIONS 1. Protect from freezing. Keep storage area neat and orderly. Remove oily rags and waste daily. Take necessary measures to ensure that workers and work areas are protected from fire and health hazards resulting from handling, mixing, and application. A. Apply water-based paints only when the temperature of surfaces to be painted and surrounding air temperatures are between 50 deg. F (10 deg. C) and 90 deg. F (32 deg. C). B. Apply solvent-thinned paints only when the temperature of surfaces to be painted and surrounding air temperatures are between 45 deg. F (7 deg. C) and 95 deg. F (35 deg. C). C. Do not apply paint in rain, fog, or mist; or when the relative humidity exceeds 85 percent; or at temperatures less than 5 deg. F (3 deg. C) above the dew point; or to damp or wet surfaces. 1. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed and heated within temperature limits specified by the manufacturer during application and drying periods. PART 2 - PRODUCTS 2.01 MANUFACTURERS A. Manufacturer: Subject to compliance with requirements, provide products of one of the following: 1. Dunn-Edwards () 2. Frazee Paints () 3. Glidden Company () 4. Benjamin Moore & Company () 5. Pittsburgh Paints () 6. Sherwin-Williams Company ()

6 2.02 PAINT MATERIALS, GENERAL A. Material Compatibility: Provide block fillers, primers, finish coat materials, and related materials that are compatible with one another and the substrates indicated under conditions of service and application as demonstrated by the manufacturer based on testing and field experience. B. Material Quality: Provide the manufacturer's best-quality trade sale paint material of the various coating types specified. Paint material containers not displaying manufacturer's product identification will not be acceptable. C. Colors: Provide color selections made by the Architect from the manufacturer's full range of standard colors MISCELLANEOUS WOOD-FINISHING MATERIALS A. Wood-Finishing Materials: Provide the manufacturer's recommended factory-formulated, wood-finishing materials that are compatible with the substrate and undercoats indicated. PART 3 - EXECUTION 3.01 EXAMINATION A. Examine substrates and conditions under which painting will be performed for compliance with paint application requirements. Surfaces receiving paint must be thoroughly dry before paint is applied. Do not begin to apply paint until unsatisfactory conditions have been corrected. Start of painting will be construed as the Applicator's acceptance of surfaces and conditions within a particular area. B. Coordination of Work: Review other Sections in which primers are provided to ensure compatibility of the total system for various substrates. On request, furnish information on characteristics of finish materials to ensure use of compatible primers.

7 3.02 PREPARATION A. General: Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and similar items already installed that are not to be painted, or provide surface-applied protection prior to surface preparation and painting. Remove these items if necessary, to completely paint the items and adjacent surfaces. Following completion of painting operations in each space or area, have items reinstalled by workers skilled in the trades involved. B. Cleaning: Before applying paint or other surface treatments, clean the substrates of substances that could impair the bond of the various coatings. Remove oil and grease prior to cleaning. Schedule cleaning and painting so dust and other contaminants from the cleaning process will not fall on wet, newly painted surfaces. C. Surface Preparation: Clean and prepare surfaces to be painted according to the manufacturer's instructions for each particular substrate condition and as specified. Provide barrier coats over incompatible primers or remove and reprime. D. Cementitious Materials: Prepare concrete, concrete masonry block, cement plaster, and mineral-fiber-reinforced cement panel surfaces to be painted. Remove efflorescence, chalk, dust, dirt, grease, oils, and release agents. Roughen as required, to remove glaze. If hardeners or sealers have been used to improve curing, use mechanical methods of surface preparation. 1. Determine alkalinity and moisture content of surfaces by performing appropriate tests. If surfaces are sufficiently alkaline to cause the finish paint to blister and burn, correct this condition before application. Do not paint surfaces where moisture content exceeds that permitted in manufacturer's printed directions. E. Clean concrete floors to be painted with a 5 percent solution of muriatic acid or other etching cleaner. Flush the floor with clean water to remove acid, neutralize with ammonia, rinse, allow to dry, and vacuum before painting. F. Wood: Clean surfaces of dirt, oil, and other foreign substances with scrapers, mineral spirits, and sandpaper, as required. Sand surfaces exposed to view smooth and dust off.

8 1. Scrape and clean small, dry, seasoned knots and apply a thin coat of white shellac or other recommended knot sealer before applying primer. After priming, fill holes and imperfections in finish surfaces with putty or plastic wood filler. Sand smooth when dried. 2. Prime, stain, or seal wood to be painted, immediately upon delivery. Prime edges, ends, faces, undersides, and backsides of wood, including cabinets, counters, cases, and paneling. 3. When transparent finish is required, backprime with spar varnish. 4. Seal tops, bottoms, and cutouts of unprimed wood doors with a heavy coat of varnish or sealer immediately upon delivery. G. Ferrous Metals: Clean ungalvanized ferrous metal surfaces that have not been shop-coated; remove oil, grease, dirt, loose mill scale, and other foreign substances. Use solvent or mechanical cleaning methods that comply with recommendations of the Steel Structures Painting Council (SSPC). 1. Touch-up bare areas and shop-applied prime coats that have been damaged. Wire-brush, clean with solvents recommended by the paint manufacturer and touch-up with the same primer as the shop coat. H. Galvanized Surfaces: Clean galvanized surfaces with nonpetroleum-based solvents so that the surface is free of oil and surface contaminants. Remove pretreatment from galvanized sheet metal fabricated from coil stock by mechanical methods. I. Materials Preparation: Carefully mix and prepare paint materials according to manufacturer's directions. Maintain containers used in mixing and applying paint in a clean condition, free of foreign materials and residue. Stir material before application to produce a mixture of uniform density; stir as required during application. Do not stir surface film into material. Remove film, and if necessary, strain material before using. Use only thinners approved by the paint manufacturer and only within recommended limits. J. Tinting: Tint each undercoat a lighter shade to facilitate identification of each coat where multiple coats of the same material are applied. Tint undercoats to match the color of the finish coat, but provide sufficient differences in shade of undercoats to distinguish each separate coat.

9 3.03 APPLICATION A. General: Apply paint according to manufacturer's directions. Use applicators and techniques best suited for substrate and type of material being applied. Paint colors, surface treatments, and finishes are indicated in the schedules. B. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to formation of a durable paint film. 1. The number of coats and the film thickness required are the same regardless of the application method. Do not apply succeeding coats until the previous coat has cured as recommended by the manufacturer. Sand between applications where sanding is required to produce a smooth even surface according to the manufacturer's directions. 2. Apply additional coats if undercoats, stains, or other conditions show through final coat of paint until paint film is of uniform finish, color, and appearance. Give special attention to ensure that surfaces, including edges, corners, crevices, welds, and exposed fasteners, receive a dry film thickness equivalent to that of flat surfaces. 3. The term exposed surfaces includes areas visible when permanent or built-in fixtures, grilles, and similar components are in place. Extend coatings in these areas as required, to maintain the system integrity and provide desired protection. 4. Paint surfaces behind movable equipment and furniture the same as similar exposed surfaces. Before the final installation of equipment, paint surfaces behind permanently fixed equipment or furniture with prime coat only. 5. Paint interior surfaces of ducts, where visible through registers or grilles, with a flat, nonspecular black paint. 6. Paint back sides of access panels and removable or hinged covers to match exposed surfaces. 7. Sand lightly between each succeeding enamel or varnish coat.

10 C. Scheduling Painting: Apply first coat to surfaces that have been cleaned, pretreated or otherwise prepared for painting, as soon as practicable, after preparation and before subsequent surface deterioration. Allow sufficient time between successive coats to permit proper drying. Do not recoat until paint has dried to where it feels firm, does not deform or feel sticky under moderate thumb pressure, and where application of another coat of paint does not cause the undercoat to lift or lose adhesion. D. Application Procedures: Apply paints and coatings by brush, roller, spray, or other applicators according to the manufacturer's directions. 1. Brushes: Use brushes best suited for the material applied. 2. Rollers: Use rollers of carpet, velvet back, or high-pile sheep's wool as recommended by the manufacturer for the material and texture required. 3. Spray Equipment: Use airless spray equipment with orifice size as recommended by the manufacturer for the material and texture required. E. Minimum Coating Thickness: Apply materials no thinner than the manufacturer's recommended spreading rate. Provide the total dry film thickness of the entire system as recommended by the manufacturer unless otherwise indicated. F. Mechanical and Electrical Work: Painting mechanical and electrical work is limited to items exposed in mechanical equipment rooms and in occupied spaces. 1. Mechanical items to be painted include, but are not limited to, piping, pipe hangers and supports, heat exchangers, tanks, ductwork, insulation, supports, motors and mechanical equipment, and accessory items. 2. Electrical items to be painted include, but are not limited to, conduit and fittings, and switchgear. G. Block Fillers: Apply block fillers to concrete masonry block at a rate to ensure complete coverage with pores filled. H. Prime Coats: Before applying finish coats, apply a prime coat of material as recommended by the manufacturer, to material that is required to be painted or finished, and that has not been prime-coated by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed

11 areas in first coat appears, to ensure a finish coat with no burn-through or other defects due to insufficient sealing.

12 I. Stipple Enamel Finish: Roll and redistribute paint to an even and fine texture. Leave no evidence of rolling such as laps, irregularity in texture, skid marks, or other surface imperfections. J. Pigmented (Opaque) Finishes: Completely cover to provide a smooth, opaque surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections will not be acceptable. K. Transparent (Clear) Finishes: Use multiple coats to produce a glass-smooth surface film of even luster. Provide a finish free of laps, cloudiness, color irregularity, runs, brush marks, orange peel, nail holes, or other surface imperfections. 1. Provide satin finish for final coats. L. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or repaint work not complying with specified requirements FIELD QUALITY CONTROL A. The Owner reserves the right to invoke the following test procedure at any time and as often as the Owner deems necessary during the period when paint is being applied: 1. The Owner will engage the services of an independent testing agency to sample the paint material being used. Samples of material delivered to the Project will be taken, identified, sealed, and certified in the presence of the Contractor. 2. The testing agency will perform appropriate tests for the following characteristics as required by the Owner: a. Quantitative materials analysis. b. Abrasion resistance. c. Apparent reflectivity. d. Flexibility. e. Washability. f. Absorption. g. Accelerated weathering. h. Dry opacity. i. Accelerated yellowness.

13 3.05 CLEANING j. Recoating. k. Skinning. l. Color retention. m. Alkali and mildew resistance. 3. If test results show material being used does not comply with specified requirements, the Contractor may be directed to stop painting, remove noncomplying paint, pay for testing, repaint surfaces coated with rejected paint, and remove rejected paint from previously painted surfaces, if upon repainting with specified paint, the two coatings are incompatible. A. Cleanup: At the end of each work day, remove empty cans, rags, rubbish, and other discarded paint materials from the site PROTECTION 1. After completing painting, clean glass and paint-spattered surfaces. Remove spattered paint by washing and scraping. Be careful not to scratch or damage adjacent finished surfaces. A. Protect work of other trades, whether being painted or not, against damage by painting. Correct damage by cleaning, repairing or replacing, and repainting as acceptable to Architect. B. Provide "Wet Paint" signs to protect newly painted finishes. Remove temporary protective wrappings provided by others to protect their work after completing painting operations. C. At completion of construction activities of other trades, touch-up and restore damaged or defaced painted surfaces EXTERIOR PAINT SCHEDULE A. General: Provide the following paint systems for the various substrates indicated. B. Ferrous Metal: Primer is not required on shop-primed items. Touch-up all damaged shop-primed metal with appropriate metal primer.

14 1. Polyurethane System: Two coats over primer. a. First Coat Epoxy Primer: DFT = 4.0 mils. IP714 High Build Amerlock 400 High-Solids epoxy 5251/5252 Glid-Guard Epoxy Chromate Primer CM33/CM34 Polyamide Epoxy Primer Pitt-Guard DTR Epoxy Series VOC System B67 Series H.D. Epoxy B60V30 b. Second and Third Coats: Alphatic Urethane Polyester; DFT = 3.0 mils per coat. IP630 Ultrashield Amershield 5410 High Solids Urethane Coating, White CM74/CM75 Aliphatic Acrylic Urethane Gloss Pitthane Acrylic-Aliphatic Urethane Series B65W301 Series/B60V30 Hi Solids Polyurethane C. Galvanized and Aluminum: 1. Gloss Finish/Alkyd Enamel: Two finish coats over primer. a. Pretreatment: Manufacturer's recommendations. b. First Coat Primer: DFT = 3.0 mils. White QD 43-7 White Anti-Corrosion Primer 661 Metal Primer 5229 All-Purpose Metal & Galvanized Primer, 155 IronClad Galvanized Metal Latex Primer Pitt-Tech DTM Primer 90 Series Direct to Metal Primer Finish B66W1 c. Second Coat: Gloss Alkyd Enamel; DFT = 2.0 mils COMPO 381 SUPER BOND 4500 Alkyd Industrial Enamel 134 Impervo Alkyd Gloss Enamel

15 Pitt-Tech DTM Acrylic Industrial Enamel, B54Z Series d. Third Coat: Gloss Alkyd Enamel; DFT = 2.0 mils. 10 SYN-LUSTRO Gloss 352 CLASSIC 4500 Alkyd Industrial Enamel 134 Impervo Alkyd Gloss Enamel Pitt-Tech DTM Acrylic Industrial Enamel, B54Z Series 3.08 INTERIOR PAINT SCHEDULE A. General: Provide the following paint systems for the various substrates as indicated. B. Concrete Masonry Units: 1. Latex Emulsion Finish: a. First Coat: Block Filler; DFT = 5-6 mils. W 305 BLOCFIL 262 Acrylic Block Filler 5317 Ultra-Hide Acrylic Block Filler 153 Moorcraft Super-Hide Block Filler 6-12 Speedhide Hi-Fill Block Filler ProMar Block Filler B25W25 b. Second and Third Coats: Semi-Gloss Finish/Latex Base; DFT = 1.3 mils. Series W450 DECOGLO 021 SATIN GLIDE 7800 Spred 2000 No VOC Semi-Gloss Trim Enamel 281 Moorcraft 100% Acrylic Semi-Gloss Speedhide Series Latex Semi-Gloss ProMar 200 Latex Semi-Gloss Enamel B31W High-Performance, Polyamide-Epoxy Coating System: Provide two finish coats with total dry film thickness not less than 4 mils over concrete masonry block filler.

16 a. Filler Coat: Concrete masonry block filler. Devoe: Glidden: : : Tnemec: Bloxfil Int/Ext Acrylic Latex Block Filler 5317 Ultra-Hide Block Filler High Performance Acrylic Block Filler. Heavy-Duty Block Filler, B42W Envirofill. b. First and Second Coats: High-performance, polyamide-epoxy coating. Devoe: Glidden: Moore: Enamel 182. : : Tnemec: 124XX Tru-Glaze 4 Epoxy Gloss Chemical-Resistant Epoxy Ironclad Chemical and Water Resistant Epoxy 97-1 Series Aquapon Polyamide-Epoxy. Tile-Clad II Epoxy Enamel B62 Series/B60V70. Series 69 Hi-Build Epoxoline II. C. Gypsum Drywall Systems: 1. Latex Emulsion Finish: Two coats over prime coat. a. First Coat Primer: Latex Base; DFT = 1.4 mils. Provide under the following finish coats. Series W420 Walltone 061 Aqua Seal 5111 Latex Primer-Sealer 273 Moorcraft Primer Sealer Speedhide 6-2 Latex Sealer ProMar 200 Latex Flat Wall Paint, B30W 200 b. Second and Third Coats: Eggshell Latex Emulsion Finish; DFT = 1.5 mils. 440 DECOSHEEN 022 LO-GLO 9300 No VOC Lifemaster 2000 Eggshell Enamel 286 Moorcraft Super-Hide Eggshell Speedhide Series Eggshell Latex Enamel ProMar 200 Latex Eg-Shel B20W 200 Series

17 2. Epoxy Enamel Finish: a. First Coat Primer: DFT = 1.5 mils. W101 VINYLASTIC 562 ARO-GARD PRIMER 5111 Latex Primer-Sealer 273 Moorcraft Primer Sealer Speedhide 6-2 Latex Wall Sealer ProMar 200 Latex Wall Primer, B28 W b. Second and Third Coats: Two coats over primer; DFT = 1.5 mils. IT 755 CERAGLAZE 542 ARO-GARD 5277/5278 Glid-Guard Acrylic Epoxy Enamel 279 Moorcraft Waterborne Acrylic Epoxy Enamel Aquapon WB Epoxy Waterborne 98 Series Water Based Catalyzed Epoxy, B70/B60V15 D. Woodwork Painted: 1. Latex Based Finish Coats: a. First Coat Primer: Latex Based; DFT = 2.0 mils. Provide under the specified finish coats. 707 UNIKOTE 367 FRAGLO 5111 Latex Primer Sealer 345 Latex Enamel Underbody Seal Grip Latex Primer Wall and Wood Primer B49WZ2 b. Second and Third Coats: Semi-Gloss Latex Finish; DFT = 1.5 mils. W450 DecoGlo 021 Satin Glide 7800 No VOC Spred 2000 Semi-Gloss Trim Enamel 281 Moorcraft 100% Acrylic Semi-Gloss

18 Series Speedhide Series Latex Semi-Gloss ProMar 200 Latex Semi-Gloss Enamel B31W 200 E. Stained Woodwork: 1. Stained-Lacquer Finish: Four finish coats over stain. F. Ferrous Metal: a. Stain Coat: Interior wood stain. LQ-120 DECOLAC 685 Wood Stain 1600 Woodmaster Oil Wood Stain 241 Interior Penetrating Stain Series, Sherwood Stains b. First Coat: Sanding Sealer. LQ-101 California DECOLAC 765 Non-Yellowing Sander Sealer 5035 Ultra-Hide Sander Sealer B44 Series ProMar Lacquer Sanding Sealer c. Second, Third, and Fourth Coats: Lacquer --- LQ Satin --- B44 Series, ProMar Lacquer Semi-Gloss 1. Latex Finish: Two finish coats over primer with minimum dry film thickness as indicated. a. Primer: Synthetic, quick-drying, rust-inhibiting primer. Omit when factory prime coated.

19 W711 VANPRIME 661 Metal Prime 5205 Tank & Structural Primer, Red 163 IronClad Retardo Rust Inhibitive Primer Pitt-Tech DTM Acrylic Primer 90 Series Kem Kromick Metal Primer B50N2/B50W1 Non- VOC b. Undercoater: Interior, Latex-Based Paint. 367 FRAGLO 300 Latex Wood Undercoater 273 Moorcraft Primer Sealer Pitt-Tech DTM Acrylic Primer 90 Series ProMar 200 Primer, B28W200 c. Satin Gloss Finish Coat: Interior, Semi-Gloss, Acrylic: W450 DECOGLO Acrylic Latex 021 SATIN GLIDE Acrylic 7800 No VOC Spred 2000 Semi-Gloss Trim Enamel 281 Moorcraft 100% Acrylic Semi-Gloss Speedhide Series Semi-Gloss Latex G. Metal-Galvanized and Aluminum: 1. Latex System: Two finish coats over primer. a. Pretreatment: Properly cleaned and etched. b. Primer: Latex-Base; DFT = 1.4 mils. W711 VAN-PRIME 661 Metal Prime 5110 Ultra-Hide Latex Vapor Barrier 155 IronClad Galvanized Metal Latex Primer Pitt-Tech DTM Acrylic Primer 90-Series B66W1, DTM Primer Finish

20 c. Semi-Gloss: Two coats over primer; DFT = 1.3 mils/coat. GLIDE W450 DECOGLO Acrylic Latex 2nd Coat FRAFLO; 3rd Coat SATIN 7800 No VOC Spred 2000 Semi-Gloss Trim Enamel 281 Moorcraft 100% Acrylic Semi-Gloss Pitt-Tech DTM Satin Acrylic 90-Series ProMar 200 Latex Semi-Gloss B31W 200 Series H. Cotton or Canvas Covering Over Insulation: % Acrylic Flat Finish: Two coats. Add fungicidal agent to render fabric mildewproof. a. First and Second Coats: Interior, Flat, Latex-Based Paint. W701 EVERSHIELD 202 DURATEC 9500 Ultra-Hide Flat Latex House Paint 171 Moorcraft Flat Speedhide ULTRA 100% Acrylic Flat Series B2WY 101 Sherclad **END OF SECTION**