CM4000 coin mechanism connection to the CANON serial interface and the XCOJL254 cable

Transcription

1 CM4000 coin mechanism connection to the CANON serial interface and the XCOJL254 cable V1.0 Cartadis is a trade mark of C.M.F tel

2 Operator accessible areas SAFETY This CMF product and supplies are manufactured and certified to strict safety regulations, electromagnetic regulations and established environmental standards. WARNING! Any unauthorised alteration, which may include the addition of new functions or connection of external devices, may impact the product certification. Please contact your CMF representative for more information. Warning markings All warning instructions marked on or supplied with the product should be followed. Electrical supply This product shall be operated from the type of electrical supply indicated on the product's data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice. To disconnect all electrical power to the product, the disconnect device is the power cord. Remove the plug from the electrical outlet. This product has been designed to restrict operator access to safe areas only. Operator access to hazardous areas is restricted with covers or guards which would have to be removed using a tool. Never remove these covers or guards. Maintenance Any operator product maintenance procedure will be described in the user documentation supplied with the product. Do not carry out any maintenance on the product which is not described in the customer documentation. Cleaning your product Before cleaning this product, unplug the product from the electrical outlet. Always use materials specifically designated for this product. The use of other materials may result in poor performance and may create a hazardous situation. Do not use aerosol cleaners, they may be flammable under certain circumstances. For more information on Environment, Health and safety in relation to this CMF product and supplies, please contact the following customer help lines: Europe : The CE mark applied to this product symbolises CMF's declaration of conformity with the following applicable European Union Directives as of the dates indicated: January 1, 1995 : Council directive 73/23/EEC, amended by Council Directive 93/68/EEC, approximation of the laws of the member states related to low voltage equipment. January 1, 1996 : Council directive 89/336/EEC, approximation of the laws of the member states related to electromagnetic compatibility. A full declaration of conformity, defining the relevant directives and referenced standards, can be obtained from your CMF representative. WARNING! In order to allow this equipment to operate in proximity to Industrial, Scientific and Medical (ISM) equipment, the external radiation from the ISM equipment may have to be limited or special mitigation measures taken.

3 1. Introduction 1.1. Generalities A CM4000 (from firmware V3.0) coin mechanism supports a new CANON serial protocol for self service usage of the copier and the printer features of a CANON MFP. A CANON serial interface, called Kit-G1 or Kit-K1, has to be ordered from CANON, see the table «Models accepted» for the Canon Mercury part number according to the MFP type. A Cartadis cable ref. XCOJL254 has to be ordered for connecting the device to the CANON serial interface. The main advantages of using this serial interface over the popular key counter interface are: Payment in self service of both copies and prints. Smart calculation of the job price based on the B&W price, colour price and paper size prices. Jobs requiring a mix of B&W and colour pages are charged at a price calculated on the accumulation of the price of each independent page. The basic features of MFP are not reduced by the serial interface: o Print and copy speed is the same as in free mode. o Automatic Document Feeder (ADF) may be used. o Automatic Colour Detection may be used too. o Duplex copy may be used. Page 3/13

4 Networked printings must be secured with a code. The CANON machine will request for this code at the time of choosing the document. Documents sent without secured code will be thrown away. One or two modes of payment are available according to the CANON MFP model: o Former generation of MFP: Supermarket mode (no printing, copying only but very user friendly interface) or Multifunction mode. o New generation of MFP (Advance range) : the Multifunction mode is only supported. The CANON MFP mode is quite innovating as the control panel of the machine is always enabled which is not usual with other similar solutions. The control panel allows starting the scan process of a copy job or the selection of a print job. Before picking up the paper (once the price is fully evaluated), MFP asks for the money of the job cost. In MFP mode, the price is set from MFP while the supermarket mode price is carried out in the Cartadis units. Attention: This interface does not enable the scan, fax or «print from USB» functions of the MFP to be used. MFP cannot be set for free printings and payable copies at the same time. Copies and printing are always payable. CM4000 must be fitted with a firmware featuring at least the V3.0 or over. XCOJL254 cable Page 4/13

5 1.2. Models accepted Following CANON Multifunction models accept this interface: CANON Model Interface to order from CANON Functioning ir3180c(i) series ir5880c(i) ir6880c(i) irc2380(i) irc2880(i) irc3080(i) irc3380(i) irc3580(i) irc4080(i) irc4580(i) irc5185(i) CLC5151 CLC4040 imagepress C1/C1+ Interface Kit-G1 code: 1782B001AA Multifunction mode or Supermarket mode imagepress C6000/C7000 ir3225 ir3230 ir3235 ir3245 ir5055 ir5065 ir5075 ir70xx series Interface Kit-G1 code: 1782B001AA Multifunction mode only ir ADV C5030(i) ir ADV C5035(i) ir ADV C5045(i) ir ADV C5051(i) ir ADV C7055i ir ADV C7065i ir ADV C9060 PRO ir ADV C9070 PRO Interface Kit-K1 code: 3725B001AA Multifunction mode only Page 5/13

6 2. Connection 2.1. Mounting XCOJL254 cable in the coin mecahnism The CM4000 coin mechanism is connected to the serial interface of the CANON MFP by using the XCOJL254 cable. This cable replaces the present XCOJL230 cable. The installation procedure is carried out in two steps: 1. Removal of the XCOJL230 cable. 2. Installation of the XCOJL254 cable. Removal of the XCOJL230 cable - Remove the cash container - Pull out the coin selector by clipping off the 2 fastening tabs from the base. - Disconnect the 4 connectors from the coin selector to the case. Fastening tabs Page 6/13

7 Remove the two ground wire fastening nuts, Copier cable XCOJL230 Cable protection slide Take out the cable protection slide by unscrewing the fastening nut Free key connector Printer connector Connect e the XCOJL254 to this connector (If needed, cut the big shoulder of the CNT12 connector) Display connector Page 7/13

8 Do not connect the printer connector. The cable and its two connectors can be removed. Replace the coin selector on its base. Replace the protection slide and the cable clip by means of a plier., 2.1. Installation of the CANON serial kit Follow the installation procedure supplied with your CANON G1 or K1 kit. Once the CANON kit has been installed, connect the female Sub-D 9 pins of the XCOJL254 cable to the male Sub-D of the CANON Kit. Lock firmly the 2 screws avoiding the connector to be pulled out and the cable to be disconnected by malicious users. Page 8/13

9 3. Setting 3.1. CANON multifunction setting The CANON serial interface is operated from the service menus Service Mode Level 1 or Level 2 by initializing the following parameters: SERVICE MODE LEVEL 1: COPIER OPTION ACC COIN = 4 or 1 (1 supermarket mode) (4 multifunction mode) (the value COIN = 0 reverts multifunction to the free mode). SERVICE MODE LEVEL 2: COPIER OPTION ACC UNIT-PRC = 1 (1 displays the Euros amount to pay) (2 displays the amount in English Pounds). Useful in supermarket mode only: SERVICE MODE LEVEL 1: COPIER OPTION BODY MODEL-SZ = 0 (0 Display of the European paper sizes in the user s interface). SERVICE MODE LEVEL 1: COPIER OPTION ACC CARD-SW (0 coin insertion) (1 card insertion). Page 9/13

10 SERVICE MODE LEVEL 1: COPIER OPTION ACC MIN-PRC = 1 (minimum value of the smallest prices in cents). SERVICE MODE LEVEL 1: COPIER OPTION ACC MAX-PRC = 9999 (maximum value of the highest prices in cents). SERVICE MODE LEVEL 1: COPIER OPTION USER B4-L-CNT = 0 (0 in case the B4 paper size is counted as an A4, 1 in case the B4 paper size is counted as an A3). SERVICE MODE LEVEL 2: COPIER OPTION USER 2C-CT-SW = 1 (0 the pages in 2 colours are counted as «mono colour», 1 the pages in 2 colours are counted as «full colour»). In case the CM4000 is disconnected, the CANON MFP displays the error E Such error code is erased from the menu: SERVICE MODE LEVEL 1: COPIER FUNCTION CLEAR ERR CM4000 coin mechanism setting The «CANON serial» communication protocol of the CM4000 is launched by setting the mode 7. There are three keys on the coin mechanism front face: Left key (LK), Middle key (MK) and Right key (RK). The setting procedure is as follows: 1. Insert the free copy key and turn it 2. Press the keys: RK, displays: STAT MK, displays: PRINT MK, displays: PRICE MK, displays: BONUS MK, displays : CONF RK, displays : DECI MK, displays: FILTER MK, displays: DlayR1 MK, displays: DlayR2 MK, displays: Reset MK, displays RestCl MK, displays : MODE RK, the current mode value comes to display, for example: 1 Press key MK up to the display of: 7 LK validates the modification 3. Take back the free copy key. Page 10/13

11 Page 11/13

12 4. Price setting 4.1. Supermarket mode Should CANON multifunction be working in «supermarket» mode (COIN=1), sales prices have to be set in CM4000. Refer to the CM4000 user s manual pages 12 and 13. Price 1 of CM4000 corresponds to an A4 copy price in black, price 2 corresponds an A3 copy price in black, price 3 to an A4 copy price in colour, price 4 to an A3 copy on colour Multifunction mode Should CANON multifunction be working in «multifunction» (COIN=4), sales prices have to be set in the multifunction (no setting in the CM4000). The following sequence of menus on the CANON MFP enables sales prices to be set: System Management Mode System Settings Charge Management Settings (page4/4) Unit Price Settings. Page 12/13

13 This menu enables prices of copies and secured printings to be set (prices may be different). Unit prices are as follows: Black small model (A4) Black large model (A3) Colour small model (A4) Colour large model (A3) Single color small model (A4) Single color large model (A3). Once prices have been set, it is strongly advisable to protect the access to the administration menu with a login/password for avoiding a user to modify your sales prices. A login/password is parameterized as follows: System Management Mode System Settings System Manager Settings System Manager ID: 1 (default value recommended by Cartadis) System Password: (default value recommended by Cartadis). Page 13/13