Light Meter (Foot Candles)

Transcription

1 Light Meter (Foot Candles) Instruction Manual SPER SCIENTIFIC LTD.

2 TABLE OF CONTENTS 1. INTRODUCTION PANEL DESCRIPTION MEASUREMENT PROCEDURES ZERO ADJUSTMENT & CALIBRATION BATTERY REPLACEMENT OPTIONAL ACCESSORIES SPECIFICATIONS LIGHT SENSOR SPECTRUM WARRANTY INTRODUCTION Compact and portable, your new meter can be used to monitor light levels or check the FC level of a particular light source. The sensor's exclusive photo diode and color correction filter meets the C.I.E. photopic spectrum. Sper Scientific light meters are cosine corrected for a quick and accurate response. Large easily legible 4 digit LCD. The meter has an external zero adjustment, data hold, low-battery indicator, and a moisture resistant front panel. Comes with soft carrying case, detachable light sensor, photo-sensor cover, instructions and a 9-Volt battery

3 2. PANEL DESCRIPTION laboratory calibration only DISPLAY 2. ON BUTTON 3. OFF BUTTON 4. HOLD BUTTON RANGE BUTTON RANGE BUTTON 7. ZERO SETTING TERMINAL 8. SENSOR INPUT SOCKET 9. STAND 10. BATTERY COMPARTMENT 11. PHOTO SENSOR 12. SENSOR PLUG - 3 -

4 3. MEASUREMENT PROCEDURES Insert the SENSOR (12) plug into the SENSOR INPUT (8) socket. Turn the meter on using the ON (2) button. Remove the lens cap from the PHOTO SENSOR (11). Press the 200 RANGE (5) button for measurements of 0 ~ FC, or select the 2000 RANGE (6) button for measurements of 200 ~ FC. If you are uncertain about which range to use, select the highest range. Range Overload is indicated when "1" appears on the left side of the display. If this occurs, switch to the highest range or discontinue use. Point the PHOTO SENSOR (11) toward the source and read the results on the display. Divide the meter reading by the factor of.0929 to convert FC results to LUX. Push the HOLD (4) button to freeze the reading in the display. The word "HOLD" appears on the LCD. Press the HOLD (4) button again to exit this function. Press the OFF (3) button to turn the unit off. Notes: Keep the lens cap on the PHOTO SENSOR (11) at all times except when actually taking a reading. Fluctuations in the reading are generally due to shadows or fluctuations in the line voltage. Ambient temperature, drafts and ventilation also affect the luminous flux output. Avoid range overload and do not store in areas of high temperature and / or humidity. Remove the battery for long-term storage

5 4. ZERO ADJUSTMENT & CALIBRATION IMPORTANT: During adjustment, be sure to use only the terminal marked "ZERO." The unmarked terminals are for professional laboratory calibration only. Tampering with the unmarked terminals will result in inaccurate readings and require professional calibration of the meter. With the sensor cover securely in place and the meter turned on, the LCD display should indicate "000" or "00.0" depending on the selected range. A slight variation will not affect readings; however, if a precise reading is required you may use the ZERO SETTING (7) terminal to reset the unit. To make an adjustment, press the 200 RANGE (5) button and cover the PHOTO SENSOR (11). Using a small screwdriver, turn the ZERO SETTING (7) terminal until "00.0" appears on the LCD. To maintain accuracy, annual laboratory calibration is recommended. For calibration service, contact SPER SCIENTIFIC, 7720 E Redfield Rd, Suite 7, Scottsdale, AZ 85260, USA. Ph , [email protected]. 5. BATTERY REPLACEMENT Replace the battery when the low battery icon is displayed in the left corner of LCD. In-spec measurements may be made for several hours after the low battery indicator appears. Remove the BATTERY COMPARTMENT (10) screw and slide the cover away from the meter, remove the battery and replace with a 9V battery (alkaline or heavy duty type). Replace the cover. 6. OPTIONAL ACCESSORIES Water Resistant Instrument Pouch Bench-Top Tripod Field Tripod - 5 -

6 7. SPECIFICATIONS Display Maximum reading 1999 Overload Indicator Sensor Power Supply "1" is displayed on the left of the LCD The exclusive photo diode and color correction filter, spectrum meets C.I.E. Cosine correction factor meets the standard. One 9V battery, current approx. DC 3mA Range* Resolution* 200 Range = 0 ~ Foot Candle 2000 Range = 200 ~ 1999 Foot Candle 200 Range = 0.1 Foot Candle 2000 Range = 1 Foot Candle Accuracy* ±5% + 4 digits Operating Temperature 32 ~ 122 F (0 ~ 50 C) Operating Humidity Less than 80% RH Weight 9.9 oz (280g) Dimensions Main Unit: 7.9 x 2.7 x 1.2" (200 x 68 x 30mm) Photo Sensor: 3.2 x 2.2 x 0.3" (82 x 55 x 7mm) Photo Sensor Lead: Extends to appx. 3½ ft *Electronic Specifications (23 ± 5 C): Tested under the environment RF Field Strength less than 3 V/M, and frequency less than the 30 MHz only

7 8. LIGHT SPECTRUM SENSOR SPER CEI - 7 -

8 WARRANTY Sper Scientific warrants this product against defects in materials and workmanship for a period of FIVE (5) years from the date of purchase, and agrees to repair or replace any defective unit without charge. If your model has since been discontinued, an equivalent Sper Scientific product will be substituted if available. This warranty does not cover damage resulting from accident, misuse, or abuse of the product. In order to obtain warranty service, ship the unit postage prepaid to: SPER SCIENTIFIC LTD E Redfield Rd, Suite 7, Scottsdale, Arizona 85260, USA ph , [email protected], The defective unit must be accompanied by a description of the problem and your return address. Please be sure to register online or return your warranty card within ten (10) days of purchase. Rev. 05/11/06-8 -