Simmerring BA.../SL to DIN 3760 A/AS
|
|
|
- Hilary Collins
- 7 years ago
- Views:
Transcription
1 Simmerring BA.../SL to DIN 3760 A/AS Simmerring BA.../SL to DIN 3760 A/AS Simmerring BAUX2, BAUSLX2, BAFUDX7, BAFUDSLX7, BA, BASL, BAU, BAUSL Product advantages Broad range of applications in every sector of industry Reliable sealing of the housing bore, even with increased roughness of the bore, thermal expansion and split housings, thus a sealing of low viscosity and gaseous media also possible Additional dust lip as additional seal against moderate and medium dust and dirt ingress from outside (BA...SL). (Note: can lead to temperature increase from frictional heat). Application Industrial gearboxes Axles (when subject to moderate dirt) Power tools. Fig. 1 Simmerring BA...SL NBR Material Acrylonitrile-butadiene rubber Code 72 NBR 902 Colour Blue Hardness 72 Shore A Metal insert Unalloyed steel DIN 1624 Spring Spring steel DIN Fig. 2 Simmerring BA...SL NBR Product description Outer casing: elastomer (smooth or grooved = X7) Spring-loaded sealing lip Additional dust lip (BA SL) Sealing lip profile, sealing lip machined on the front face (BAUX2, BAUSLX2 = preferred type) Sealing lip profile, finished sealing lip (BAFUDX7/BAFUDSLX7). 147
2 Operating conditions Media Mineral oils, synthetic oils*, greases T C short term up to +120 C Circumferential speed [m/s] Speed [revs/min] FKM v NBR p Shaft diameter [mm] Permissible circumferential speed for Simmerrings made from the materials NBR (72 NBR 902) and FKM (75 FKM 585) for the sealing of motor oil SAE 20. Use Simmerring with SL (dust lip): v = max. 8 m/s. up to 0,05 MPa/0,5 bar for >0,05 MPa/0,5 bar, a Simmerring with back-up ring can be used Technical handbook. up to 0,02 MPa/0,2 bar (BAFUDX7/BAFUDSLX7) * With synthetic oils (polyalkylene glycols/polyalphaolefins, Technical Manual synthetic lubricants) it is to be noted that the maximum operating temperature of 80 C must not be exceeded. Max. permissible values depend on the other operating conditions. Fitting & installation Shaft Tolerance ISO h 11 Runout IT 8 Roughness Hardness Finish Housing bore R a = 0,2 0,8 µm R z = 1,0 5,0 µm R max = <6,3 µm HRC No lead; preferably plunge ground Tolerance ISO H8 Roughness rubber OD covering R z = µm Careful fitting according to DIN 3760 is a prerequisite for the correct function of the seal Technical Manual. Range of dimensions for shafts- d 1 Simmerring BA... Simmerring BA...SL mm mm 148
![..500 Shaft diameter [mm] Permissible circumferential speed for Simmerrings made from the materials NBR (72 NBR 902) and FKM (75 FKM 585) for the sealing of motor oil SAE 20.](/docs-images/44/21038677/images/page_2.jpg "Use Simmerring with SL (dust lip): v = max. 8 m/s. up to 0,05 MPa/0,5 bar for >0,05 MPa/0,5 bar, a Simmerring with back-up ring can be used Technical handbook.")
3 Article list min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A smooth 0,05 72 NBR 902 BA 6325 B A smooth 0,05 72 NBR 902 BA 1931 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 6335 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 6341 B A smooth 0,05 72 NBR 902 BAU 6344 B A grooved 0,02 72 NBR 902 BAFUDX B A grooved 0,02 72 NBR 902 BAFUDX D AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 6365 B A smooth 0,05 72 NBR 902 BA 6372 B A smooth 0,05 72 NBR 902 BA 6374 B A smooth 0,05 72 NBR 902 BA 7566 B AS smooth 0,05 72 NBR 902 BASL B A smooth 0,05 72 NBR 902 BA 6397 B A smooth 0,05 72 NBR 902 BA 6403 B A smooth 0,05 72 NBR 902 BAU 6405 B A smooth 0,05 72 NBR 902 BA 6412 B A smooth 0,05 72 NBR 902 BA 6418 B A smooth 0,05 72 NBR 902 BA 6421 B A smooth 0,05 72 NBR 902 BA 6431 B A smooth 0,05 72 NBR 902 BA 6438 B A smooth 0,05 72 NBR 902 BAU 6443 B A smooth 0,05 72 NBR 902 BA 6445 B 9,5 25,4 8 A smooth 0,05 72 NBR 902 BAU 6454 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BASL 6463 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 6467 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 6485 B 149
4 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BASL 6486 B A smooth 0,05 72 NBR 902 BA 6492 B AS smooth 0,05 72 NBR 902 BASL 3360 B A smooth 0,05 72 NBR 902 BA 6501 B A smooth 0,05 72 NBR 902 BAU 6504 B A smooth 0,05 72 NBR 902 BA 6511 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 6518 B A smooth 0,05 72 NBR 902 BA 6528 B A smooth 0,05 72 NBR 902 BA 6550 B A smooth 0,02 72 NBR 902 BAFUD B A grooved 0,02 72 NBR 902 BAFUDX B ,5 A smooth 0,05 72 NBR 902 BA 6555 B A smooth 0,05 72 NBR 902 BAU 6564 B ,5 A smooth 0,05 72 NBR 902 BA 6572 B A smooth 0,05 72 NBR 902 BA 6575 B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BAU 6590 B A smooth 0,05 72 NBR 902 BAU 6598 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 2669 B A smooth 0,05 72 NBR 902 BA 6620 B A smooth 0,05 72 NBR 902 BA 6629 B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 6633 B A smooth 0,05 72 NBR 902 BAU 6635 B 12, A smooth 0,05 72 NBR 902 BAU 6637 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 6656 B A smooth 0,05 72 NBR 902 BA 6658 B A smooth 0,05 72 NBR 902 BAU 6663 B AS smooth 0,05 72 NBR 902 BASL 3367 B A smooth 0,05 72 NBR 902 BA 6671 B 150
5 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAU 6683 B AS smooth 0,05 72 NBR 902 BAUSLX D A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BA 6694 B A smooth 0,05 72 NBR 902 BA 6700 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 6713 B A smooth 0,05 72 NBR 902 BAU 6717 B AS smooth 0,05 72 NBR 902 BASL B A smooth 0,05 72 NBR 902 BA 6723 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 6726 B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 6736 B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAUSL B A smooth 0,05 72 NBR 902 BA 6747 D A smooth 0,05 72 NBR 902 BAUSL 6749 B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 6753 B ,5 A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BASL 6764 B A smooth 0,05 72 NBR 902 BAU 7592 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 6780 B A smooth 0,05 72 NBR 902 BAU 6784 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 7595 B A smooth 0,05 72 NBR 902 BA 6795 B AS smooth 0,05 72 NBR 902 BASL 6796 B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 6802 B A grooved 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 6805 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA D 151
6 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 6829 B A smooth 0,05 72 NBR 902 BAU 6839 B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 6845 B A smooth 0,05 72 NBR 902 BA 2746 B AS smooth 0,05 72 NBR 902 BASL 6847 D A smooth 0,05 72 NBR 902 BA 6851 B A smooth 0,05 72 NBR 902 BAU 6857 B A grooved 0,05 72 NBR 902 BAUX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 7616 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 6870 D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BASL 6878 B AS smooth 0,05 72 NBR 902 BASL D A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BASL 2184 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 6884 B AS smooth 0,05 72 NBR 902 BASL B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 6893 D AS smooth 0,05 72 NBR 902 BASL 6898 B A smooth 0,05 72 NBR 902 BA 6899 B A smooth 0,05 72 NBR 902 BA 6904 B AS smooth 0,05 72 NBR 902 BASL B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B ,5 A smooth 0,02 72 NBR 902 BAFUD B 152
7 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A smooth 0,05 72 NBR 902 BAU 7653 B A grooved 0,02 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 6924 B 17, A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA D A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 7664 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAU 2751 B AS smooth 0,05 72 NBR 902 BASL 6959 B A smooth 0,05 72 NBR 902 BA 2752 B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 6967 B A smooth 0,05 72 NBR 902 BAUSL 6978 B A smooth 0,05 72 NBR 902 BA 6979 B A smooth 0,05 72 NBR 902 BA 6980 D A smooth 0,05 72 NBR 902 BA 6984 B A smooth 0,05 72 NBR 902 BA 9588 B A smooth 0,05 72 NBR 902 BA 6989 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 6994 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU B AS smooth 0,05 72 NBR 902 BASL 7003 B A smooth 0,05 72 NBR 902 BA 7008 B A smooth 0,05 72 NBR 902 BA 7015 B 19,05 31,75 6,35 A smooth 0,05 72 NBR 902 BA 7022 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 7071 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7081 B A smooth 0,05 72 NBR 902 BAUSL 7095 B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7110 B A smooth 0,05 72 NBR 902 BA 7112 B A smooth 0,05 72 NBR 902 BA 7714 B A smooth 0,05 72 NBR 902 BA 7718 D AS smooth 0,05 72 NBR 902 BASL 7721 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 7124 B 153
8 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A smooth 0,05 72 NBR 902 BAU 7136 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 7723 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 7724 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7194 B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 7197 B A smooth 0,05 72 NBR 902 BAU 7209 B A smooth 0,05 72 NBR 902 BA 7217 B AS smooth 0,05 72 NBR 902 BASL 7530 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 8976 B ,5 A smooth 0,05 72 NBR 902 BAU 7230 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 7727 B A smooth 0,05 72 NBR 902 BAU 7238 B A smooth 0,05 72 NBR 902 BA 7243 B A smooth 0,05 72 NBR 902 BA 7249 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 7252 B AS smooth 0,05 72 NBR 902 BASL 7254 D A smooth 0,05 72 NBR 902 BAU 7259 B A smooth 0,05 72 NBR 902 BAU 7269 B A smooth 0,05 72 NBR 902 BAU 7273 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7282 B 154
9 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7301 B AS grooved 0,02 72 NBR 902 BAFUDSLX D A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BA 7311 B A smooth 0,05 72 NBR 902 BAU B AS smooth 0,05 72 NBR 902 BASL 7325 B A smooth 0,05 72 NBR 902 BAU 7329 B A smooth 0,05 72 NBR 902 BAU 7331 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAU 7337 B A smooth 0,05 72 NBR 902 BA 7340 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7350 B A grooved 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA D A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX D A smooth 0,05 72 NBR 902 BAU 7374 B A smooth 0,05 72 NBR 902 BA 7380 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 7389 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUSL 7413 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 7426 B A grooved 0,02 72 NBR 902 BAFUDX B 25 42,9 9,5 A smooth 0,05 72 NBR 902 BA 7746 B A smooth 0,05 72 NBR 902 BA 7438 B A smooth 0,05 72 NBR 902 BA 7446 B A smooth 0,05 72 NBR 902 BAUSL 7755 B A smooth 0,05 72 NBR 902 BAU 7457 B A grooved 0,02 72 NBR 902 BAFUDX D A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B 155
10 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 7460 B A smooth 0,05 72 NBR 902 BA 7467 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 7483 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 7488 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7503 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 7520 B A smooth 0,05 72 NBR 902 BAUSL 3402 B A smooth 0,05 72 NBR 902 BAU 7525 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 7535 B AS smooth 0,05 72 NBR 902 BASL B A smooth 0,05 72 NBR 902 BAU 9567 B A smooth 0,05 72 NBR 902 BAU 7540 B A smooth 0,05 72 NBR 902 BA 7546 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 7549 B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BA 7558 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 7564 B A smooth 0,05 72 NBR 902 BA 7567 B A smooth 0,05 72 NBR 902 BA 7573 B A smooth 0,05 72 NBR 902 BA 7576 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 7582 B 156
11 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BASL 7771 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 7601 B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BASL 7603 B 28 42,5 8 A smooth 0,05 72 NBR 902 BA 7605 B 28 42,9 9,5 A smooth 0,05 72 NBR 902 BA 7608 B A smooth 0,05 72 NBR 902 BA 7611 B ,5 A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 7613 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BASL 7618 B A smooth 0,05 72 NBR 902 BAU 7623 B A smooth 0,05 72 NBR 902 BAU 7631 B A smooth 0,05 72 NBR 902 BAU B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7639 B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 7645 B A grooved 0,05 72 NBR 902 BAUX B 29 42,9 9,5 A smooth 0,05 72 NBR 902 BA 7650 B A smooth 0,05 72 NBR 902 BAU 7652 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS grooved 0,02 72 NBR 902 BAFUDSLX B ,7 A smooth 0,05 72 NBR 902 BAUX B ,7 AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7685 B A smooth 0,05 72 NBR 902 BAU 7686 B AS smooth 0,02 72 NBR 902 BAFUDSL B ,5 A smooth 0,05 72 NBR 902 BAU 7695 B A smooth 0,05 72 NBR 902 BAU 7700 B A smooth 0,05 72 NBR 902 BAUSL B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX D AS smooth 0,02 72 NBR 902 BAFUDSL D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7708 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAU 7716 D 157
12 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A grooved 0,02 72 NBR 902 BAFUDX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 7729 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 7741 B A smooth 0,05 72 NBR 902 BAU 7742 B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 7758 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUSL 7767 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7772 B A smooth 0,05 72 NBR 902 BA 7775 B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 7783 B A smooth 0,05 72 NBR 902 BA 7788 D A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,02 72 NBR 902 BAFUD B ,5 A smooth 0,05 72 NBR 902 BAUX D A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 7798 B A grooved 0,02 72 NBR 902 BAFUDX B 158
13 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7811 B A smooth 0,05 72 NBR 902 BA 7815 B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BA 7821 B A smooth 0,05 72 NBR 902 BAUSL 7822 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAUSL B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 7833 B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 7838 B A smooth 0,05 72 NBR 902 BAUSL 7842 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 7850 B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7856 B AS grooved 0,02 72 NBR 902 BAFUDSLX D AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 7862 B AS smooth 0,02 72 NBR 902 BAFUDSL D A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 7875 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 7920 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 7921 B A smooth 0,05 72 NBR 902 BAU 7926 B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 7931 B A smooth 0,05 72 NBR 902 BA B ,5 AS smooth 0,05 72 NBR 902 BAUSLX B ,5 A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B 35 49,3 9,5 A smooth 0,05 72 NBR 902 BA 7970 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 7976 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX D A smooth 0,05 72 NBR 902 BAU D 159
14 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 8008 B A smooth 0,05 72 NBR 902 BAUSL D AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 8018 B A smooth 0,05 72 NBR 902 BA 8021 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 8032 B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8049 B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUSL 8055 B A smooth 0,05 72 NBR 902 BA 8060 B A smooth 0,05 72 NBR 902 BAUSL B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BASL B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 3441 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 8074 B 160
15 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 8083 B A smooth 0,05 72 NBR 902 BA B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8112 B A smooth 0,05 72 NBR 902 BA 8118 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BAU 8135 B ,5 A smooth 0,05 72 NBR 902 BA 8137 B A smooth 0,05 72 NBR 902 BA 8141 B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAU 8145 B A smooth 0,05 72 NBR 902 BA D A smooth 0,05 72 NBR 902 BA 8150 B A smooth 0,05 72 NBR 902 BA 8151 B A smooth 0,05 72 NBR 902 BAU 8153 B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BAU 8156 B A smooth 0,05 72 NBR 902 BA 8162 B A smooth 0,05 72 NBR 902 BA 8165 B A smooth 0,05 72 NBR 902 BAUSL B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BAUSL 8167 B A smooth 0,05 72 NBR 902 BA 8169 B A grooved 0,05 72 NBR 902 BAUX B ,5 A smooth 0,05 72 NBR 902 BA 8188 B A smooth 0,05 72 NBR 902 BAUX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BASL 8222 B A smooth 0,05 72 NBR 902 BAU D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX D A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8226 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8234 B AS smooth 0,05 72 NBR 902 BASL 8235 B A smooth 0,05 72 NBR 902 BA 8239 B A smooth 0,02 72 NBR 902 BAFUD B 161
16 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8249 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAU 8254 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8279 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8286 B AS smooth 0,05 72 NBR 902 BASL B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 8298 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8304 B A smooth 0,05 72 NBR 902 BA 8307 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8310 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8312 B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 8318 D A smooth 0,05 72 NBR 902 BAUX B 162
17 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,02 72 NBR 902 BAFUDSL B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BAU 8342 B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUSL B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BA 8356 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8363 B A smooth 0,05 72 NBR 902 BA 8367 B A smooth 0,05 72 NBR 902 BA 8373 B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 8381 B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8393 B 44 58,4 10 A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BAU 8406 B A smooth 0,05 72 NBR 902 BA 8408 B A smooth 0,05 72 NBR 902 BA 8414 B A smooth 0,05 72 NBR 902 BA 8420 B A smooth 0,05 72 NBR 902 BAU B A grooved 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8442 B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 8447 B A grooved 0,02 72 NBR 902 BAFUDX D AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8454 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B ,5 AS smooth 0,05 72 NBR 902 BASL 8461 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUSL 8479 B 163
18 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 8483 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,02 72 NBR 902 BAFUDSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D AS grooved 0,02 72 NBR 902 BAFUDSLX D A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,02 72 NBR 902 BAFUD B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B A grooved 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX D A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUSL D A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8536 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8543 B A smooth 0,05 72 NBR 902 BAU B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUSL D A smooth 0,05 72 NBR 902 BA B A smooth 0,05 72 NBR 902 BA 8560 B A smooth 0,05 72 NBR 902 BAU 8562 B 164
19 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,02 72 NBR 902 BAFUDSL B 46, A smooth 0,05 72 NBR 902 BA 8578 B A smooth 0,05 72 NBR 902 BA 8582 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8597 B A smooth 0,05 72 NBR 902 BAU 8604 B A smooth 0,05 72 NBR 902 BAUSL 8606 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8617 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8624 B A grooved 0,02 72 NBR 902 BAFUDX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8633 B A smooth 0,05 72 NBR 902 BA 8640 B A smooth 0,05 72 NBR 902 BAUSL 8641 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 8648 B ,5 A smooth 0,05 72 NBR 902 BAUSL D AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8655 D A smooth 0,05 72 NBR 902 BAUSL 8659 D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BAUSLX D A smooth 0,05 72 NBR 902 BAU 8662 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 8668 B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 8670 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8677 B A smooth 0,05 72 NBR 902 BA D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 8694 B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8711 B A smooth 0,05 72 NBR 902 BAU 8713 B 165
20 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 8716 B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8720 B A smooth 0,05 72 NBR 902 BAUSL B AS smooth 0,05 72 NBR 902 BAUSLX B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BA 8742 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 8747 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8749 B A smooth 0,05 72 NBR 902 BA 8751 B A smooth 0,05 72 NBR 902 BA 8753 B A smooth 0,05 72 NBR 902 BA 8763 B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 8781 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8799 B 166
21 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAU 8815 B A smooth 0,05 72 NBR 902 BA 8822 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 8825 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8834 B A smooth 0,05 72 NBR 902 BAU B A smooth 0,05 72 NBR 902 BA 8836 B A smooth 0,05 72 NBR 902 BAU 8838 B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8850 B A smooth 0,05 72 NBR 902 BA 8856 B A smooth 0,05 72 NBR 902 BA 2799 B A smooth 0,05 72 NBR 902 BA B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A grooved 0,02 72 NBR 902 BAFUDX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 8883 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 8909 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8920 D AS smooth 0,05 72 NBR 902 BASL 8927 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B 167
22 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 8941 B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 8952 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAU 8963 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 8965 B A smooth 0,05 72 NBR 902 BA 8978 B A smooth 0,05 72 NBR 902 BA 8983 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 2794 B A smooth 0,05 72 NBR 902 BA B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 9003 B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,05 72 NBR 902 BAUSLX D A smooth 0,05 72 NBR 902 BAU 9011 D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 9015 B 168
23 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BA 9030 B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 9041 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUSL D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUSL 9060 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BA 9062 B A smooth 0,05 72 NBR 902 BAU 9066 B A grooved 0,02 72 NBR 902 BAFUDX B A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9095 B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,05 72 NBR 902 BAUSLX D AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 9101 B A smooth 0,05 72 NBR 902 BAUSL 9102 B A smooth 0,05 72 NBR 902 BAU 9106 B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAU 9108 B A smooth 0,05 72 NBR 902 BA 9110 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU D A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BAU 9122 B A smooth 0,05 72 NBR 902 BAU 9128 B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B 169
24 min = b + 0,3 b H8 d 1 h11 d 1 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9130 B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BA B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 9137 B A smooth 0,05 72 NBR 902 BAUX B A grooved 0,02 72 NBR 902 BAFUDX B AS grooved 0,02 72 NBR 902 BAFUDSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9142 B A smooth 0,05 72 NBR 902 BAU D A grooved 0,02 72 NBR 902 BAFUDX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA 9149 B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU 9157 B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BASL B AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,02 72 NBR 902 BAFUDSL B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU 9172 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B AS grooved 0,02 72 NBR 902 BAFUDSLX B A smooth 0,05 72 NBR 902 BAU 9189 B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B 170
25 d 1 b DIN 3761 Outer surface Pressure Material Type Article No AS smooth 0,02 72 NBR 902 BAFUDSL B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9198 B A smooth 0,05 72 NBR 902 BAU 9204 B A smooth 0,05 72 NBR 902 BAU 9216 D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9221 B AS smooth 0,02 72 NBR 902 BAFUDSL B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA 9234 B A smooth 0,02 72 NBR 902 BAFUD B AS smooth 0,05 72 NBR 902 BAUSLX B A grooved 0,05 72 NBR 902 BAUX B AS grooved 0,05 72 NBR 902 BAUSLX B A grooved 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAUX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BASL 9242 B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAU 9244 B AS smooth 0,05 72 NBR 902 BAUSLX B AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BA B AS grooved 0,05 72 NBR 902 BAUSLX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,05 72 NBR 902 BAU D AS smooth 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A grooved 0,02 72 NBR 902 BAFUDX B A smooth 0,02 72 NBR 902 BAFUD B A smooth 0,05 72 NBR 902 BA B AS smooth 0,05 72 NBR 902 BAUSLX B AS grooved 0,05 72 NBR 902 BAUSLX B A smooth 0,05 72 NBR 902 BAUX B A smooth 0,05 72 NBR 902 BAU B A grooved 0,02 72 NBR 902 BAUX B 171
Self-aligning ball bearings
Self-aligning ball bearings Designs... 470 Basic design... 470 Sealed bearings... 470 Bearings with an extended inner ring... 472 Bearings on sleeves... 473 Self-aligning ball bearing kits... 474 Appropriate
Technical Data. 7. Bearing Fits. 7.1 Interference. 7.2 Calculation of interference F B LLLLLLLLL( A-54
Technical Data 7. Bearing Fits 7.1 Interference For rolling s the rings are fixed on the or in the housing so that slip or movement does not occur between the mated surface during operation or under. This
Machine Design II Prof. K.Gopinath & Prof. M.M.Mayuram. Module 2 - GEARS. Lecture 17 DESIGN OF GEARBOX
Module 2 - GEARS Lecture 17 DESIGN OF GEARBOX Contents 17.1 Commercial gearboxes 17.2 Gearbox design. 17.1 COMMERCIAL GEARBOXES Various commercial gearbox designs are depicted in Fig. 17.1 to 17.10. These
Roller bearing life. The Reaction of AISI 52100 Bearing Steel to Heat
Roller bearing life in high temperatures A common question maintenance personnel ask bearing companies when their equipment temperature is high or rises is, What is the maximum temperature that your rolling
Special Rolling Bearings
Special Rolling Bearings Special Rolling Bearings KINEX produces, except a large number of types and sizes of standardized rolling bearings of both basic and modified designs presented in the preceding
SITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents
English translation of German original Technical Information TI-P11 SITEMA PowerStroke Mould Closing Devices series FS drive system for powerful forces on a short stroke hydraulic actuation closing force
PS-SEAL PTFE based high performance seal
PS-SEAL PTFE based high performance seal Advancing the Science of Sealing Advancing the Science of Sealing Table of content PS-SEAL 3 PS-SEAL STANDARD Standard seal in stock 4 PS-SEAL NON-STANDARD Customized
TECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
gasket type & material overview
gasket type & material overview gaskets a gasket is placed in between two objects in order to prevent leakage of any kind of the pressurized or not pressurized media. most important is the compression
Grooved gaskets. Types of gaskets
Types of gaskets have proven extremely useful in all areas of industry, including the most demanding sealing tasks. Our grooved gaskets can be found in conventional power plants as well as in the primary
Having given due consideration to all aspects
INTRODUCTION 2 Introduction. Having given due consideration to all aspects of the shaft seal assembly (including the bore, the shaft, and the design of the seal itself), what remains is to successfully
QUAD-RING R Seal. Description... 2. Applications... 3. Materials... 4. Design Instructions... 6. Installation Instructions... 10
Contents Description... 2 Applications... 3 Materials... 4 Characteristics and inspection of elastomers... 4 Design Instructions... 6 Installation Instructions... 10 Installation Recommendations... 11
3097 en - 2013.06 / e. This manual is to be given to the end user POULIBLOC 2000-3000. Shaft mount reducer. Installation
097 en - 0.06 / e 8 en This manual is to be given to the end user POULIBLOC 000-000 Installation LEOY-SOME ISTALLATIO POULIBLOC 000-000 097 en - 0.06 / e This document complements the general instructions
Metric roller bearing units SYNT and FYNT series (SKF ConCentra)
Metric roller bearing units SYNT and FYNT series (SKF ConCentra) Bearing types Spherical roller bearings Bearing dimension series 222 Shaft diameter range 35 to 100 mm SKF ConCentra roller bearing units
Improved Life for Dynamic Seals in Wind Turbine Applications
Improved Life for Dynamic Seals in Wind Turbine Applications By Elizabeth Chitren - Product Engineer, Klozure Dynamic Seals, Palmyra, NY Jim Drago, P.E. - Manager, Engineering, Garlock Sealing Technologies,
THRUST NEEDLE ROLLER AND CAGE ASSEMBLIES Assembly Dimensions, Load Ratings, Thrust Washer and Piloting Dimensions... 480-487
Thrust Bearings Page Nomenclature............................................ 474 Introduction............................................. 476 Identification.............................................
Rickmeier Solutions. Gear pumps for superior Lubrication
Rickmeier Solutions Gear pumps for superior Lubrication P U M P E N T E C H N O L O G I E #1. Introduction Position and significance of Rickmeier products Rickmeier supplies pumps, valves and systems for
For New Technology Network. Steel Manufacturing Machinery Product Guide Book
For New Technology Network R Steel Manufacturing Machinery Product Guide Book Ecological / Economical proposals from NTN NTN products exhibit benefits at various locations. Steel manufacturing equipment
Merkel Seals and Sealing Systems for the Metal Processing Industry. Product Information Metal Processing Industry
Merkel Seals and Sealing Systems for the Metal Processing Industry Product Information Metal Processing Industry Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global
NEW SIX-SEALS CUTTING RING. INTERNATIONAL INDUSTRIAL PATENT Nr. 864061 of the 10/03/99 FLANKS AND DOES NOT REPLACE THE STANDARD RING CURRENTLY IN USE
B4 NEW SIX-SEALS CUTTING RING. INTERNATIONAL INDUSTRIAL PATENT Nr. 864061 of the 10/03/99 FLANKS AND DOES NOT REPLACE THE STANDARD RING CURRENTLY IN USE AVAILABLE IN CARBON AND STAINLESS STEEL 23 THEORY
SITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents
SITEMA PowerStroke FSP ocking, actuating and releasing by pneumatic pressure English translation of German original Technical Information TI-P1 SITEMA PowerStroke Mould Closing Devices series FSP drive
High precision ball bearings
GMN Paul Müller Industrie GmbH & Co. KG Äussere Bayreuther Str. 230 D-90411 Nuremberg Phone: +49 911-5691-0 Fax: +49 911-5691-221 www.gmn.de High precision ball bearings Ball bearings: Phone: +49 911-56
Metal-O-rings and C-rings for extreme operating conditions
Metal-O-rings and C-rings for extreme operating conditions From ultrahigh vacuum up to 6800 bar (100000 psi) pressure and temperatures from -269 C cryogenic up to +980 C (-425 F up to 1800 F). Resistant
Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS
Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS up to size 381; to PN 0.5; to T = 80 C 1. Description 1.1. General FSA fluid level gauges, FSK fluid level sensors and TS temperature
Hydraulic multidisc Brake H420
S320gb - rev 02/09 S E R V I C E Hydraulic multidisc Brake H420 A N U A L WARNER ELECTRIC EUROPE Rue Champfleur, B.P. 20095, F- 49182 St Barthélemy d Anjou Cedex Tél. +33 (0)2 41 21 24 24, Fax + 33 (0)2
Journal bearings/sliding bearings
Journal bearings/sliding bearings Operating conditions: Advantages: - Vibration damping, impact damping, noise damping - not sensitive for vibrations, low operating noise level - dust tight (if lubricated
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
Bearing designation is created by numerical and letter symbols indicating the type, size and design of the bearing, see the scheme.
2.2 Designation Bearing designation is created by numerical and letter symbols indicating the type, size and design of the bearing, see the scheme. In the basic design the bearings are designated by a
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23 Application Pressure regulators for set points from 5 mbar to 28 bar Valves in nominal sizes DN 15 to 100 Nominal pressures
Radial piston pumps type R and RG
Radial piston pumps type R and RG Operating pressure p max = 700 bar Delivery flow Q max = 91.2 lpm (at 1450 rpm) Geometric displacement V g max = 64.2 cm 3 /rev. 1. General Motor pumps and hydraulic power
Digital pressure gauge for industrial applications Model DG-10-S, Standard version Model DG-10-E, Enhanced version
Electronic pressure measurement Digital pressure gauge for industrial applications Model DG-10-S, Standard version Model DG-10-E, Enhanced version WIKA data sheet PE 81.66 Applications Machine building
2CP. Twin-impeller pumps PERFORMANCE RANGE INSTALLATION AND USE APPLICATION LIMITS OPTIONALS AVAILABLE ON REQUEST CONSTRUCTION AND SAFETY STANDARDS
2CP Twin-impeller pumps PERFORMANCE RANGE Flow rate up to 40 l/min (27 m³/h) Head up to 112 m APPLICATION LIMITS Manometric suction lift up to 7 m Liquid temperature between -10 C and +90 C Ambient temperature
ENERGY HYDRO POWER SOLUTIONS FOR ELECTRICAL POWER TRANSFER ELECTRICAL PROTECTION SEALING
ENERGY HYDRO POWER SOLUTIONS FOR ELECTRICAL POWER TRANSFER ELECTRICAL PROTECTION SEALING MERSEN A world leader committed to Renewable Energies A world leading supplier of electrical protection, sealing,
kymanual or Automatic - it s your Choice
. kymanual or Automatic - it s your Choice ky LKB Automatic or Manual Butterfly Valve Application LKB is a sanitary automatically or manually operated butterfly valve for use in stainless steel pipe systems.
Mechanical shaft seal types and sealing systems
Chapter 2 Mechanical shaft seal types and sealing systems 1. Mechanical shaft seal types 2. Sealing systems 3. Selecting a mechanical shaft seal Mechanical shaft seal types and sealing systems 1. Mechanical
DODGE USAF 200/300 Direct Mount Pillow Block Bearings
DODGE USAF 200/300 Direct Mount Pillow Block Bearings These instructions must be read thoroughly before installation or operation. WARNING: To ensure that drive is not unexpectedly started, turn off and
Profile rail guides LLR
Profile rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout
ZKL- ZRL Praha, a.s. MANUFACTURER OF BALL BEARINGS
ZKL- ZRL Praha, a.s. MANUFACTURER OF BALL BEARINGS CATALOG OF BEARINGS Contents Introduction... 3 Technical Section... 4 Single Row Ball Bearings... 4 Self-Aligning Ball Bearings... 4 Special Ball Bearings...
Piston Accumulators. SK Series. Accumulator Catalog. Piston Types. Description. Sealing Systems. End Cap. O-ring. Sealing System. Piston.
SK Series Piston Types TYPE 2 pplication: Low-friction design for higher piston speeds, slow movements without stick-slip effect and high number of actuations (millions). ctual cycles achieved will vary
Machine Screws, Dowel Pins and Hardware
Machine Screws, Dowel Pins and Section Contents Plain Socket Head Screws...Page 13-2 Wire Locking Screws...Page 13-3 Captive Screws...Page 13- Ventilation Screws...Page 13- Shoulder Screws...Page 13-
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08. Linear Motion and Assembly Technologies
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08 Linear Motion and Assembly Technologies STAR Linear Motion Technology Ball Rail Systems Standard Ball Rail Systems Ball Rail Systems with Aluminum
TECHNICAL DATA SHEET GRILON BG-15 S
TECHNICAL DATA SHEET GRILON BG-1 S Grilon BG-1 S is a heat stabilised PA6 injection moulding grade with 1% glass fibres. Grilon BG-1 S has the following important properties: Excellent surface finish Easy
Lubricant distributors
Lubricant distributors Product series AB, 341, 340, 351, 350, 391, 390, VR, 321, VN, 370, 361 For oil, fluid grease, and grease For use in SKF MonoFlex single-line centralized lubrication systems SKF MonoFlex
Assisted lift operated 2/2-way solenoid valves Type EV250B
MAKING MODERN LIVING POSSIBLE Data sheet Assisted lift operated 2/2-way solenoid valves Type EV250B EV250B with assisted lift can operate from zero and up to 10 bar differential pressure. This 2/2-way
Pressure transmitter For general industrial applications Model A-10
Electronic pressure measurement Pressure transmitter For general industrial applications Model A-10 WIKA data sheet PE 81.60 for further approvals see page 9 Applications Machine building Shipbuilding
1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
SCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.
SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of
TRELLEBORG SEALING SOLUTIONS. Rotary Seals YOUR PARTNER FOR SEALING TECHNOLOGY
TRELLEBORG SEALING SOLUTIONS Rotary Seals YOUR PARTNER FOR SEALING TECHNOLOGY Your Partner for Sealing Technology Trelleborg Sealing Solutions is a major international sealing force, uniquely placed to
Performance Cylindrical OD Bearings (ER) Felt Seal & Flinger. Grade 10 Steel Balls. Lubrication Groove. Zone Hardened. Black Oxided.
Mtd. Ball Performance Cylindrical OD (ER) Sealmaster ER Style Ball Sealmaster Gold ER bearings feature a cylindrical OD and snap ring for easy installation in a roll assembly. Shaft lock is achieved by
Cerobear Spindle Bearings for Machine Tool Applications
Cerobear Spindle Bearings for Machine Tool Applications Cerobear Spindle Bearings About CEROBEAR Committed to the abbreviation CEramic in ROlling BEARings, CEROBEAR GmbH is the renowned world leader in
7.3 Fit selection. Inner ring: Rotating. Outer ring: Stationary. Inner ring: Stationary. Outer ring: Rotating. Inner ring: Stationary
7. Bearing Fits 7. Fitting For rolling s, inner and outer rings are fixed on the or in the housing so that relative movement does not occur between fitting surfaces during operation or under. This relative
DMP 331. Industrial Pressure Transmitter for Low Pressure. Stainless Steel Sensor
DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO from 0... 00 mbar up to 0... 40 bar Output signals
Metal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
FAG SPECIAL SPHERICAL ROLLER BEARINGS FOR VIBRATING MACHINES
FAG SPECIAL SPHERICAL ROLLER BEARINGS FOR VIBRATING MACHINES FAG OEM und Handel AG FAG Special Spherical Roller Bearings for Vibrating Machines Publ. No. WL 1 100/3 EA FAG OEM und Handel AG A company of
LINEAR MOTION CONTROL
LINEAR MOTION CONTROL Technical Data Sheet Static Locks RLSS Series Nexen s new generation of linear holding/locking devices take rod locking technology to the next level. With superior performance, these
Solenoid valves 2/2-way direct-operated Type EV210A
Solenoid valves 2/2-way direct-operated Type EV210A Features EV210A NC and NO Very compact valves for industrial application, such as control and dosage For water, oil, compressed air and similar neutral
- CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL 301 - DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING 401
CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 70 204 PERFORMANCE CURVE 90 205 PERFORMANCE CURVE 120 206 PERFORMANCE CURVE 200 207 - CONSTRUCTIONS
Tool Technology for Mechanical Metal Surface Improvement
Motorenbau Engine Construction Festwalzen Deep Rolling Automobilindustrie Automotive Industry MMS MQL Glätten Smoothing Kaltverfestigung Strain Hardening Medizintechnik Medical Industry Glattwalzen Roller
ROTEX. ROTEX Operating-/Assembly instructions design A-H. KTR-N sheet: edition: 40226 E 1
406 E 1 Torsionally flexible jaw-type couplings, and their combinations, size 19 90 according to Standard 94/9/EC (ATEX 95) for finish bored, pilot bored and unbored couplings, size 100 15 406 E is a torsionally
X15TN TM. A high hardness, corrosion and fatigue resistance martensitic grade CONTINUOUS INNOVATION RESEARCH SERVICE.
TM A high hardness, corrosion and fatigue resistance martensitic grade CONTINUOUS METALLURGICAL SPECIAL STEELS INNOVATION RESEARCH SERVICE DEVELOPMENT Enhancing your performance THE INDUSTRIAL ENVIRONMENT
Rolling Bearing for Environments of Ultrahigh Temperatures
[ New Product ] Rolling Bearing for Environments of Ultrahigh s Miki ARIHANA* Takayuki KAWAMURA** In recent years the demand of bearings which are used at 4 degree C for tenter clips, glassmaking facility
Installation instruction
1/5 ATTENTION! Mounting and dismounting of a shrink disc must be restricted to qualified personnel. Incorrect handling may cause injury to persons and damage to machines! At work, with heavy parts and
TECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. 2012NB Description 304mm (12") Automatic Thickness Planer CONCEPTION AND MAIN APPLICATIONS * Compact and light weight (27 Kg./59 lbs) automatic thickness planer for easier
ZKL Bearings for Railway Rolling Stock
2 ZKL Bearings for Railway Rolling Stock ZKL Bearings for Railway Rolling Stock Railway industry is a very prospective sector worldwide and therefore ZKL pays particular attention to bearings for railway
7 Bearings. Bearing Surface. Shaft Hardness and Finish
7 Bearings Bearings and bushings of ZYTEL nylon resin and DELRIN acetal resin are used in numerous commercial applications. ZYTEL is uniquely suited to abrasive atmospheres such as in cement plants and
E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SERIES 51
83 300/100 ED E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SUBPLATE MOUNTING CETOP P05 p max 250 bar Q max (see specification table) MOUNTING INTERFACE OPERATING PRINCIPLE
SKF precision bearings
SKF precision bearings Contents Made by SKF stands for excellence. It symbolises our consistent endeavour to achieve total quality in everything we do. For those who use our products, Made by SKF implies
COMPARING STRENGTH PROPERTIES OF NATURAL AND SYNTHETIC RUBBER MIXTURES
COMPARING STRENGTH PROPERTIES OF NATURAL AND SYNTHETIC RUBBER MIXTURES T. Renner, L. Pék Institute for Mechanical Engineering Technology, Faculty of Mechanical Engineering, www.geti.gek.szie.hu Abstract:
Specifications. Model Flow type Pressure type. Air Maximum operating pressure. 1.0 MPa Ambient and fluid temperature. 3% F.S.
Electro-Pneumatic Proportional Valve Series /VEP Electro-pneumatic proportional valve: Flow type () Controls the flow rate steplessly according to current. (It is a / port valve that has an electrical
CAT. 0113-GB MODELS. Series. Flat-face quick-release couplings. UNI EN ISO 9001 Cert. n 2905 ISO/TS 16949
CAT. 0113-GB NEW MODELS Flat-face quick-release couplings UNI EN ISO 9001 Cert. n 2905 ISO/TS 16949 FLAT-FACE QUICK-RELEASE COUPLINGS Features Benefits Applications Flat-face shut-off valves: easy to clean.
SKF Seals Knowledge Engineering. Designed to optimize machinery performance
SKF Seals Knowledge Engineering Designed to optimize machinery performance From moulding high quantities to mach Sealing for power transmission The performance and service life of a power transmission
2/2 and 3/2 Way Size 6 Seat Valves
2/2 and 3/2 Way Size 6 Seat Valves Directly operated Interface and subplate dimensions according to DIN 24340 and ISO Line connection port size G 3/8" Cartridge design PN [p max. ] = 315 bar 7501856.06.12.08
Excerpted From Components Toughen Up
A l t r a I n d u s t r i a l M o t i o n Warner Electric Boston Gear TB Wood s Formsprag Clutch Wichita Clutch Marland Clutch Excerpted From Components Toughen Up Industrial Clutch Bauer Gear Motor Svendborg
P.E.D. 97/23/EC/0424 Butterfly Valves Series SL, SLK Group 1-2 Class I, II, III ATEX CE Ex II 2 GD
1. GENERAL 1.1 CONSTRUCTION Small size and light construction gives advantage in installation, stocking and transporting. Sizes from DN 300 to 600 are equipped with ears, which helps the centering of the
Operating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
Series 8146/5-V37 and Series 8150/5-V37
www.stahl.de > Clear assignment safe technology easy installation > Intelligent structure only one rotary actuator for frequency-controlled drives ) 20 ms leading auxiliary contact for safe motor disconnection
Micro oil-mist lubricator, Series NL2-LBM G 1/4
Version Micro oil-mist lubricator, an be assembled into blocks Mounting orientation vertical Working pressure min./max. 0.5 bar / 6 bar Medium ompressed air Neutral gases Medium temperature min./max. -0
Technical Information. Hydrostatic Spindles. Hydrostatik by Hyprostatik. Innovative Spindle Concepts
Technical Information Hydrostatic Spindles Hydrostatik by Hyprostatik Innovative Spindle Concepts 2 Table of contents 1. Advantages and disadvantages of hydrostatic spindles 4 1.1 Advantages of hydrostatic
Drawn Cup Needle Roller Bearings
Drawn up Needle Roller Bearings NSK has introduced the most advanced bearing technology, offering unprecedented precision and reliability. Available in two types caged and full complement. High-quality
SKF composite plain bearings. Compact and maintenance-free
SKF composite plain bearings Compact and maintenance-free Contents The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as
HOW THE CONTAMINATION IS MEASURED CONTAMINATION CLASSES ACCORDING TO ISO 4406:1999
CONTAMINATION CONTROL in hydraulic systems in the hydraulic system is a very wide and complex matter; the following is just a short summary. Our Customer Service is at your disposal for any further information.
Refrigeration and air conditioning Date: 10/2013
Catalogue 40 WEH Connectors for filling, evacuating and testing of refrigeration and air conditioning components Refrigeration and air conditioning Date: 10/2013 WEH - We Engineer Hightech All rights reserved,
Cylindrical Roller Bearings
Cylindrical Roller Bearings TI-I-4010.0 / E Historical Location Headquarters of IBC Wälzlager GmbH in the industrial area of Solms-Oberbiel The headquarters, with the plants Solms-Oberbiel and Asslar are
Industrial seal self study guide. Maximizing radial shaft seal performance.
Industrial seal self study guide Maximizing radial shaft seal performance. TABLE OF CONTENTS Chapter 1 Introduction........................ 2-4 Basic Seal Types................. 5-9 Chapter 2 Review.................
Flow divider (flow distributor), type TQ
Flow divider (flow distributor), type TQ Pressure p max = 0 bar Flow Q CN max = 00 lpm Share ratio = :. General Task Flow dividers type TQ are self-regulating valves, which largely irrespective of the
Overflow valve with thread connection
Operation Installation and Maintenance Instructions Overflow valve with thread connection hp-technik GmbH Industriepumpen-Förderaggregate und Anlagenbau Gablonzer Straße 21 D-76185 Karlsruhe Germany Tel.:
Hochpräzisions-Wälzlager High Precision Bearings
Tel: +49/64 41/95 53-02 Fax: +49/64 41/5 30 15 POSTFACH 1825 35528 WETZLAR (GERMANY) e-mail: ibc@ibc-waelzlager.com Industriegebiet Oberbiel D-35606 Solms-Oberbiel http://www.ibc-waelzlager.com IBC INDUSTRIAL
Cylinders DIN ISO 6431 and VDMA 24 562
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
Geometry and dimensional tolerances of engine bearings
Geometry and dimensional tolerances of engine bearings Dr. Dmitri Kopeliovich (Research & Development Manager.) 1. Hydrodynamic lubrication Engine bearings operate mostly in the hydrodynamic regime of
Study on Design and Performance Prediction Methods for Miniaturized Stirling Engine
99SETC-42 Study on Design and Performance Prediction Methods for Miniaturized Stirling Engine Copyright 1998 Society of Automotive Engineers, Inc. Koichi HIRATA, Dr. Power and Energy Engineering Division,
Spiroflex spiral-wound gaskets
Spiral-wound gaskets have long been used as sealing elements in refineries, chemical plants, gas installations, water treatment plants and in general pipeline construction. Spiroflex gaskets SpV retain
Hydraulic cylinders Tie rod design. Type CD70 / CG70. Contents. Features. RE 17016 Edition: 2014-03 Replaces: 08.08
Hydraulic cylinders Tie rod design Type CD / CG RE 1 Edition: 2014-03 Replaces: 08.08 Series Component series 1X Nominal pressure bar [7 MPa] Features Contents types of mounting Piston Ø (ØAL)... mm Piston
Contents BUSHING S ELECTION P RODUCT S PECIFIC I NFORMATION TECHNICAL DATA A SSORTMENT. World s Widest Bushing Stock Assortment 2
SKF bushings Contents BUSHING S ELECTION World s Widest Bushing Stock Assortment 2 SKF Bushings Product Guide 4 SKF Bushings Technical Data 6 Bushing Selection Overview of Technical Data Temperature range
VdS 2100-09en. VdS Guidelines for water extinguishing systems. Non-return valves. Requirements and test methods. VdS 2100-09en : 2011-05 (01)
VdS Guidelines for water extinguishing systems VdS 2100-09en Requirements and test methods VdS 2100-09en : 2011-05 (01) Publishing house: VdS Schadenverhütung GmbH Amsterdamer Str. 172-174 50735 Köln,
Special products More than just standard. FEP O-rings. Endless vulcanisation PTFE. Round cords. Mouldings. O-Ring treatments.
FEP O-rings Endless vulcanisation PTFE Round cords Mouldings O-Ring treatments Special services Special products More than just standard When it matters Premium-Qualität m quality ität since 1867 COG For
CDX. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page - CONTENTS 100
CONTENTS Page - CONTENTS 100 - SPECIFICATIONS 200 SELECTION CHARTS 201 PERFORMANCE CHART 70 202 PERFORMANCE CHART 90 203 PERFORMANCE CHART 120 204 PERFORMANCE CHART 200 205 - CONSTRUCTIONS 300 SECTIONAL
Unit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 2 HYDRAULIC AND PNEUMATIC CYLINDERS The material needed for outcome 2 is very extensive
MECHANICAL LOSS REDUCTION OF A 100 W CLASS STIRLING ENGINE. Koichi HIRATA National Maritime Research Institute, Japan
1 MECHANICAL LOSS REDUCTION OF A 100 W CLASS STIRLING ENGINE Koichi HIRATA National Maritime Research Institute, Japan E-mail: khirata@nmri.go.jp ABSTRACT We have developed a 100 W class displacer-type