DEMO MANUAL DC1613A I 2 C/SMBUS/PMBUS Controller DESCRIPTION DEMONSTRATION CIRCUIT

Transcription

1 DEMO MANUAL DCA I C/SMBUS/PMBUS Controller DESCRIPTION Demonstration circuit A is a USBbased controller with generic Inter Integrated Circuit (I C) ports as well as SMBUS/PMBUS capabilities. It is designed to mate with Linear Technology s family of LTpowerPlay demonstration boards. The demo board is fully isolated from the host PC s ground. The evaluation software automatically detects which demo board is connected and loads the appropriate control screen. The LTpowerPlay system provides a quick and easy way to evaluate the performance of a wide variety of Linear Technology s products L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and LTpowerPlay is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. DEMONSTRATION CIRCUIT TO SMBUS TO USB dcaf

2 DEMO MANUAL DCA QUICK START PROCEDURE For proper equipment setup, follow the procedure below:. Do NOT plug in the DCA to the PC, before running the installation program.. Download the LTpowerPlay installation program from Run the LTpowerPlay installation program and follow the onscreen instructions. The LTpowerPlay demo software requires a PC that is running Windows XP (or later), and has an available USB port.. Connect the demonstration circuit to be evaluated to the DCA using the supplied conductor ribbon cable. The demo software detects the circuit and starts the appropriate control screen. Each demonstration board also comes with a Quick Start guide similar to this one. For usage details relevant to a particular circuit refer to its Quick Start guide. SOFTWARE TOOLS The LTpowerPlay demo software includes tools for automatic software updates and for quickly retrieving relevant documentation from the World Wide Web. NOTE: Adobe Acrobat Reader is required to view the documents and is available at To use the tools: Quit the demonstration circuit software or disconnect the USB cable so that the main control panel appears: To update the software (requires internet connection): Choose Update from the Tools menu. This automatically updates the main program and drivers for individual demo circuits. dcaf

3 DEMO MANUAL DCA TROUBLESHOOTING GUIDE Problem: DCA is plugged in, but LTpowerPlay screen still says USB Serial Controller Not Connected. Solution: The most likely cause is improper installation of the USB drivers, which causes Windows to recognize the DCA as an Unknown Device. Open the Windows Control Panel, open System and click the Device manager tab. Open the Other Devices item and look for USB SERIAL CONTROLLER. Select this item and click the remove button. Unplug the DCA, reinstall the LTpowerPlay software and follow the onscreen instructions. Problem: Demo board software loads properly, but will not run or gives Device Not accessible errors. Solution: Verify that the demo board is properly powered up. This Quick Start guide lists the basic power connections to DCA. Some demo boards may have additional requirements; refer to the demo board s Quick Start guide for details. Problem: After connecting the demo board to DCA with the supplied pin ribbon cable, LTpowerPlay software still displays Evaluation Board is not Connected. Solution: Contact Linear Technology Applications Engineering. dcaf

4 DEMO MANUAL DCA SCHEMATIC DIAGRAM ECO REV _ REVISION HISTORY DESCRIPTION APPROVED DATE PRODUCTION 090 VPIC D D C 0.uF C 0.uF U PICLF9I/PT RA RA USB_TXE# USB_WR_CLK# USB_RXF# USB_RD_CLK# RB/CS NXP_WR_ ALERTB NXP_INT_ RX/RC NXP_RD_ TX/RC NXP_CE_ C MOSI/RC RC/MOSI/SDAO C MISO/RC RC/MISO/SDAI R0 RC_SCK.99k JP SCK/RC SYSTEM_RST# NXP_A0_ RC MCLR RC NXP_A_ OUTEN RC0 0 PIC_DB R RD AUX_MAIN# RE/CS RD PIC_DB M HDX09 RD PIC_DB GPO_ RE/WR RD PIC_DB RD 0 PIC_DB GPO_ RE0/RD RD 9 PIC_DB RD PIC_DB RD0 PIC_DB0 R k PROG JP HDX09 COMMAND LED LTSTC90KGKT (LITEON) GRN VDD 0 OSCIN PGD/RB PGC/RB RB RB RB OSCOUT RB RB INT/RB0 0 9 R 9.9k R USB_RXF# 9 VSS VSS VDD R 0k U LTC99CS SET OUT DIV R. C 0.uF RA RA RA RA RA RA0 0 9 B B ASSY R R R R R R Q Q A B 0 k k N00 N00 LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMERSUPPLIED SPECIFICATIONS; NOTES: UNLESS OTHERWISE SPECIFIED A TECHNOLOGY Fax: (0)00 HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. KT LTC ConfidentialFor Customer Use Only A VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL. ALL RESISTORS ARE IN OHMS, 00. APPLICATION. COMPONENT SUBSTITUTION AND PRINTED APP ENG. TITLE: SCHEMATIC ALL CAPACITORS ARE IN MICROFARADS, 00. CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR IC / SMBUS / PMBUS CONTROLLER TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE.. INSTALL SHUNTS ON JUMPERS AS SHOWN. CUSTOMER NOTICE APPROVALS THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. SCALE = NONE SIZE DATE: 0 McCarthy Blvd. Milpitas, CA 90 Phone: (0)900 IC NO. REV. N/A DEMO CIRCUIT A M onday, April 9, 00 SHEET OF dcaf

5 DEMO MANUAL DCA SCHEMATIC DIAGRAM C9 0.uF R USBV C 0.uF D D C 0.uF C 0.uF C0 0uF,.V 00 PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB0 USB_RD_CLK# RD USB_WR_CLK# WR RSTOUT USB_TXE# TXE USBV C USB_RXF# R0 C R 0k MHZ USBV R. U LTC90CS9 SET R 0k OUT DIV 0 D D D D D D D0 SI/WU PWREN RST B B U FTBL USBDM USBDP VOUT C 0.uF R. C 0.uF C pf 0k C9 pf U 9LCBTI/OT CS CLK DO VSS DI C 0.0uF USBV J A 0 VIO 9 D 0 RXF XTIN XTOUT EECS EESK EEDATA TEST USBB MILLMAX 9 9 A C 0.uF R k EN DIS EE R9.k R 0k JP HDX09 R. R9 0 0 R.k CUSTOMER NOTICE APPROVALS LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMERSUPPLIED SPECIFICATIONS; A TECHNOLOGY Fax: (0)00 HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. KT LTC ConfidentialFor Customer Use Only A VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED APP ENG. TITLE: SCHEMATIC CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR IC / SMBUS / PMBUS CONTROLLER TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. SCALE = NONE SIZE DATE: 0 McCarthy Blvd. Milpitas, CA 90 Phone: (0)900 IC NO. REV. N/A DEMO CIRCUIT A M onday, April 9, 00 SHEET OF dcaf

6 DEMO MANUAL DCA SCHEMATIC DIAGRAM JP IO U0 E ACCEL LTCCDC IO IO NONISOLATED ISOLATED V U EN E ( 0.V ) CTRL V R DIS.k W0 ENABLE V S W B OE X0 NC BUS E W B B X A RA Z0 B X Z A R C0 A BUS Y uF B Z B B B Y Y A 9 0 A C C 0.0uF IO 0uF,.V FSTMTCX D D R9 R0 UA R U 00.99k k LT0CS V.99k PCA9PW C C V 0.uF JP INT D0 VDD 0 C 0.uF D SDA 9 R 0.uF EXT D SCL 99 UA R V V HCD D PU RESET# Q R UB D INT# U C U D A k LT0CS HCPL09J 0.uF MCBDG D A0 C V R IO 9 D CE# 0 I.C. RD# R VDD VDD R R R9 0.uF CONTROL 9 VSS WR# 0k 0k 0k 0k W PIC_DB0 PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB PIC_DB IN OUT X W W0 OUT R IN Y W0 W IN OUT.99k Z UA OUT X0 NC NC 9 W X UB R HCD HCD JP X0 X Q X INT Y Y0 Y0 0 Y EXT Y PU Z0 R Z NXP_WR_ NXP_RD_ NXP_CE_ NXP_A0_ NXP_A_ NXP_INT_ Z R0 Z0 99 Z UC IO V UB HCD J RC_SCK C C HCD V V 9 SDA AUXP C U SDA 0.uF R MOCD0M R R R k k.99k.99k SCL SCL LGKPWR CTRL ALERTB A COL UD GPO_ AUX_MAIN# HCD 9 OUTEN UD C E HCD GPO ISO R 0 GPO_ A COL AUXSCL AUXSDA C E GPO_ V HDX09 U C9 V UC HCD R9 MOCD0M R 0.uF.99k R.99k U0A 9 k k R9 LT0CS OUTENISO A COL OUTEN C E B B GPO ISO A COL IO GPO_ C E U0B LT0CS U, SDA/SCL THRESHOLDS V IO R0 k VIL = 0. VDD X. = 0.99V U9 R MOCD0M.9k k R R VIH=0.VDDX.=.V k R COL A VOL@0mA < 0.V (0 OHM).99k E C COL A ALERTB ALERTB_ISO E C 0 0 VEE VSS ( LOW LEVEL = 0.V ) VDD 0 McCarthy Blvd. CUSTOMER NOTICE APPROVALS Milpitas, CA 90 A LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A Phone: (0)900 A CIRCUIT THAT MEETS CUSTOMERSUPPLIED SPECIFICATIONS; TECHNOLOGY Fax: (0)00 HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. KT LTC ConfidentialFor Customer Use Only VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED APP ENG. TITLE: SCHEMATIC CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR IC / SMBUS / PMBUS CONTROLLER TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. SIZE IC NO. REV. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. SCALE = NONE N/A DEMO CIRCUIT A DATE: M onday, April 9, 00 SHEET OF dcaf

7 DEMO MANUAL DCA SCHEMATIC DIAGRAM NONISOLATED ISOLATED RA VSW D D E VSW C0 C C C 0.uF 0uF,V 0.uF 00uF,.V 0 00 JP U LT9EFE R T D Q U Q VPIC 0k PA00 BATS USBV SiDS E RSENSE LTES. N00 SHDN COLA 0. OHM VIN OUT SYNC COLB E A RSL C 00 C 0uF,.V CT U 0.0uF 00 LTC0CS SHDN BYP RT C R VSEN R 0uF,.V R9 ON 0k D CT CG C BATS C C C R.nF,000V C9 C0 R0 0pF.9k 0 0.uF 0.uF 00 C 0.0uF U USBV JP9 VSW LTES V HDX09 ON VIN OUT OFF C R C 0k R 0uF,.V SHDN BYP 0.0uF.k 00 ISO PWR LED USBV E C USBV 0uF,.V LTSTC90KGKT 00 (LITEON) GRN E U LTES. IO E9 JP0 VIN OUT B B ISO PWR C 0.0uF SW ISO 0 P P VIN E0 INT EXT SHDN BYP C 0uF,.V 00 CUSTOMER NOTICE 0 McCarthy Blvd. APPROVALS Milpitas, CA 90 LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A Phone: (0)900 CIRCUIT THAT MEETS CUSTOMERSUPPLIED SPECIFICATIONS; TECHNOLOGY Fax: (0)00 A A HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. KT LTC ConfidentialFor Customer Use Only VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED APP ENG. TITLE: SCHEMATIC CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR IC / SMBUS / PMBUS CONTROLLER TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. SIZE IC NO. REV. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. SCALE = NONE N/A DEMO CIRCUIT A DATE: M onday, April 9, 00 SHEET OF Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. dcaf

8 DEMO MANUAL DCA DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design, marketing, and/or manufacturingrelated protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 0 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 0 McCarthy Blvd. Milpitas, CA 90 Copyright 00, Linear Technology Corporation LT 00 PRINTED IN USA Linear Technology Corporation 0 McCarthy Blvd., Milpitas, CA 90 (0) 900 FAX: (0) 00 LINEAR TECHNOLOGY CORPORATION 00 dcaf