FORMULA Industrial Monitors

Transcription

1 FORMULA Industrial Monitors DOC-IWS-713 Revision A

2 Nematron FORMULA Users Guide The Nematron FORMULA Industrial Monitors Users Guide (DOC-IWS-713) describes the installation and operation of the Nematron FORMULA Monitor models. This document is based on information available at the time of its publication. While every effort has been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software. Nematron makes no warranty and assumes no responsibility for the completeness, accuracy or usefulness of the information found in these pages. Nematron further assumes no liability or responsibility for loss or damage, direct or indirect, arising from the use of this product. No warranties of documentation or product fitness apply. Nematron, PowerVIEW, and NemaSoft, are registered trademarks of Nematron Corporation. Industrial Control Computer, Industrial Workstation, and FlexBox are trademarks of Nematron Corporation. All other brand and product names are trademarks or registered trademarks of their respective companies. Electrical Shock Hazard! Do not operate the unit with its back cover removed. There are hazardous voltages inside. Servicing of the equipment should only be done by qualified and authorized personnel. CAUTION! Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. Note: The unit must be mounted in a grounded metal enclosure that provides a clean and dry environment or mounted using a VESA mounting arm system when the unit is installed in a clean and dry environment. Customer Service: Contact your local Nematron Sales Representative. For assistance in locating your Sales Representative, call (734) for North America or call +44 (0) for Europe, Middle East and Asia. Also, visit us on the Web at Copyright 2006 Nematron Corporation. All rights reserved. 2 of 35 DOC-IWS-713A

3 Chapter 1: User Guide Documentation Revision History Rev Date Notes A Oct., 2006 Initial release Feb., of 35 DOC-IWS-713A

4 Table of Contents Chapter 1: User Guide Documentation Revision History...3 Chapter 2: Transport, Unpacking and Accessories...6 Chapter 3: FORMULA Industrial Monitor Product Overview General Information Formula Monitor concept Model Number...8 Chapter 4: FORMULA Display Module Display Module Chassis...9 Chapter 5: FORMULA Mounting Instructions Unit Dimensions, Cutout, Weight and Power Consumption Installation Instructions Vesa Mounting Mounting in a Panel...11 Chapter 6: Formula Monitor Connections Connectivity Supported Input Formats VGA (Analog Video Interface) DVI (Digital Video Interface) USB Touch Screen Connection Dynapro Touch Screen Installation Steps ELO Touch Screen Installation Steps Audio Support Power Connections and Power Up...18 Chapter 7: OSD (On Screen Display) OSD Key description OSD menu Touch screen Removing the Rear Cover...26 Chapter 8: FORMULA Maintenance Replacing the Backlights...27 Chapter 9: FORMULA Troubleshooting...28 Appendix A: Model Configurator details...29 Appendix B: FORMULA Monitor, 15inch Cutout, Weight, Power consumption and Dimensions, Appendix D: FORMULA Monitor, 17inch Cutout, Weight, Power consumption and Dimensions of 35 DOC-IWS-713A

5 Appendix E: Technical Data of 35 DOC-IWS-713A

6 Chapter 2: Transport, Unpacking and Accessories Transport Despite the robust design of the FORMULA Industrial Monitor, the components are sensitive to strong vibrations and impacts. During transport, your FORMULA should therefore be protected from excessive mechanical stress. Therefore, please use the original packaging. Danger of damage to the FORMULA! If the FORMULA is transported in cold weather or is exposed to extreme variations in temperature, make sure that moisture (condensation) does not form on or inside the FORMULA. Prior to operation, the FORMULA must be allowed to slowly adjust to room temperature. Should condensation occur, a delay time of approximately 12 hours must be allowed before the FORMULA is switched on. Unpacking Proceed as follows to unpack the FORMULA: 1. Remove packaging. 2. Do not discard the original packaging. Keep it for future relocation. 3. Check the delivery for completeness by comparing it with your order. 4. Please keep the associated paperwork. 5. Check the contents for visible shipping damage. 6. If you notice any shipping damage or inconsistencies between the contents and your order, you should notify the supplier. Accessories The following accessories are included in the accessory box: Part Description IF5M IF7M N KEY, HEXAGON SOCKET, 2.5mm, IF 1 1 N CLIP, MOUNTING, + SCREW M5/H, IF A0731E Formula driver CD-ROM * Power Cord, 220V 1 1 N CABLE, VGA, 1.8m 1 1 N CABLE, DVI, 1.8m 1 1 N * CABLE, TS, USB A-B, 1.8m 1 1 N PS, 48W, FSP048-1AD101C, IFM 1 1 Notes: 1, USA/Canadian units includes 110V power cord 2, No N cable with non-touch Monitors 3, Unit with 3M Touch Screen contains Touch Screen pen 6 of 35 DOC-IWS-713A

7 Chapter 3: FORMULA Industrial Monitor Product Overview This chapter gives a complete physical description of your Nematron FORMULA Monitor, including all specifications and ratings. 3.1 General Information This manual covers the Nematron 15 and 17 FORMULA Industrial Monitor models IF5M and IF7M. The Monitors are coming either with a standard 15 XGA TFT Display with 1024x768 resolution or 17 SXGA TFT Display with 1280x1024 resolution and 16M colors. All Models have standard a VGA Video Input and a DVI (Digital Video Interface) input, Audio IN/Audio Speakers outputs and an external Power Adapter. 3.2 Formula Monitor concept 7 of 35 DOC-IWS-713A

8 3.3 Model Number Located on the back of the unit chassis a label shows the unit s model and serial numbers. The serial number is unique to the unit and the model number describes the options with which the unit was configured: I F M = Industrial 9 = 0 2 = FORMULA 10 = 0 3 = Display Size 11 = 0 4 = Monitor 12 = 0 5 = Keyboard Options 13 = 0 6 = Touch screen 14 = 0 7 = - 15 = Options 8 = 0 The actual electronic contents of your product can be verified with the configuration provided in Appendix A which is located in the back of this user guide. 8 of 35 DOC-IWS-713A

9 Chapter 4: FORMULA Display Module 4.1 Display Module Chassis The Display Module is the front part of the complete FORMULA Monitor. It consists of the TFT display, TFT display Inverter, Touch Controller Card and Touch screen. The display chassis consists of two parts: Front part which has the touch screen and the rear part which has the TFT display, Inverter and Touch Controller card. Front and rear parts are hold together by captive thumbscrews. The rear part is together assembled with the Control Board chassis. 9 of 35 DOC-IWS-713A

10 Chapter 5: FORMULA Mounting Instructions Remove your unit from the packaging and set it up according to the instructions in this chapter. 5.1 Unit Dimensions, Cutout, Weight and Power Consumption. See for detailed information Appendixes B and C. 5.2 Installation Instructions The Nematron FORMULA industrial Monitor is designed to be mounted in a paneled enclosure or using a VESA mounting arm system. To mount the FORMULA in a panel, use the mounting clips supplied with the unit. 5.3 Vesa Mounting. Four Mounting holes are implemented for a standard VESA Mounting (arm) system. The assembly can be screwed on using four M4 screws with a maximum length of 10mm (3.93 ). 10 of 35 DOC-IWS-713A

11 5.4 Mounting in a Panel To mount the unit in a panel: 1. Prepare a cutout of the appropriate size, as specified in Appendix B or C. 2. Position the FORMULA Monitor in the cutout. 3. From the rear of the unit, insert the mounting clips into the slots on the top, bottom, and sides of the unit. The appropriate number of mounting clips and the required Allen wrench to tighten them are provided for each model. Installing in a Panel Using Mounting Clips 4. Using the Allen wrench supplied, tighten the mounting clip screws in a criss-cross pattern (top left, bottom right, bottom left, top right, etc.), each a little at a time until five to seven inch-pounds ( Nm) of torque is reached on each screw. Do not completely tighten any one screw at one time. The result could be an inadequate seal or deformation of the front bezel. 11 of 35 DOC-IWS-713A

12 Chapter 6: Formula Monitor Connections 6.1 Connectivity Below picture shows the location of the different connectors for connecting the Formula Monitor to a controller. Picture: What where to Connect 12 of 35 DOC-IWS-713A

13 6.2 Supported Input Formats The Formula Monitor can support any video mode within the following input constraints: Signal sample frequency with the input 80MHz Horizontal sync frequency between 30KHz and 80KHz The modes are detected with the presentation of the input and previous alignments for setup are automatically recalled. The emulation of a true multi-sync monitor is implemented. The factory preset supported modes are as follows: Notes: 1. All mentioned modes are non-interlaced. The maximum and minimum frame rates are decided by the TFT- LCD. 2. Factory preset modes are overwritten by additional user alignments for automatic recall. The factory preset modes can be recalled at any time. 13 of 35 DOC-IWS-713A

14 6.3 VGA (Analog Video Interface) The Formula Monitor has one VGA input port which can be connected to almost every computer. Analog VGA Input Connector (Connector Mini D-Sub 15 pin) 14 of 35 DOC-IWS-713A

15 6.4 DVI (Digital Video Interface) The Formula Monitor has one DVI input port which complies with VESA DVI standard. Therefore, users can make direct interface to the DVI output of Digital VGA cards. The signal source can be switched through OSD. DVI-I Input Connector (Connector DVI-D (DVI 1)) 15 of 35 DOC-IWS-713A

16 6.5 USB Touch Screen Connection Connect the USB Touch Screen input connector on the Monitor to a free USB port from your Controller with either the standard delivered USB cable or your own. The Monitor input connector should be of the USB-B type. 6.6 Dynapro Touch Screen Installation Steps 1. Connect Formula monitor VGA/DVI cable to Engine or Computer; 2. Connect Formula monitor Touch Screen cable to Engine or Computer; 3. Connect Formula monitor power cable to electric socket; 4. Turn On computer; 5. Turn On Formula Monitor; 6. Use Formula Drivers CD-ROM; 7. Run \Formula drivers\touchscreen\model IFxxx7 Dynapro\Ver \Win200XP\Setup.exe 8. Install Dynapro TouchScreen driver 9. Leave box Auto 4Pts Calibration Utility blank 10. Leave box Install PS/2 interface driver blank 11. After completion installation follow calibrate Touch screen instructions. 6.7 ELO Touch Screen Installation Steps 1. Turn On computer; 2. Use Formula Drivers CD-ROM; 3. Run \Formula drivers\touchscreen\model IFxxx6 ELO\Win2000,XP\EloSetup.exe; 4. Install ELO TouchScreen driver; 5. Select Install USB Touch screen drivers 6. Select Auto-detect ELO device 7. Select to calibrate ELO Touch screen monitors. 8. After completion installation follow calibrate Touch screen instructions. 6.8 Audio Support The Formula Monitor has a Hi-Fi Stereo Audio amplifier that users can control by using OSD interface. There is one input channel to the audio input port. The audio output is 2 x 2 8 ohm, and users can easily configure the audio interface features by using the earphone output and speaker output ports. Audio Input Connector (Connector Stereo Jack) 16 of 35 DOC-IWS-713A

17 Audio Output Connector (Connector Stereo Jack) 17 of 35 DOC-IWS-713A

18 6.9 Power Connections and Power Up Note: Please refer to Appendix B, C and E for details on the AC power supply. 1. Check product label for correct unit voltage. 2. Plug the DC power jack from the Power Supply Adapter into the unit. 3. Connect the AC power cord in the Adapter and plug the power cord in to an AC outlet. 4. The AC power cord provides the necessary earth grounding for safety but also an additional earth point (Chassis Ground) can be used. 5. The unit is now ready to power up. Press on the Power Switch to switch on the Monitor. 6. The FORMULA Monitor should now start up the power up sequence. 18 of 35 DOC-IWS-713A

19 Chapter 7: OSD (On Screen Display) 7.1 OSD Key description MENU : Menu Key DOWN (EXIT) : Exit Key (HOT Key: Auto Config.) DECREASE (-) : Decrease Key, Left Key (HOT Key: Audio Decrease) INCREASE (+) : Increase Key, Right Key (HOT Key: Audio Increase) SOURCE : Source Select HOT Key: Source Select [Analog DVI][-Composite-S- Video {option}] Power Light : Power Indicator LED ON/OFF : Power on/off switch 19 of 35 DOC-IWS-713A

20 7.2 OSD menu The OSD menu enables users to manipulate the image and setting Color Adjustments 20 of 35 DOC-IWS-713A

21 7.2.2 Picture Adjustments 21 of 35 DOC-IWS-713A

22 7.2.3 Function Selection 22 of 35 DOC-IWS-713A

23 7.2.4 OSD Menu variables 23 of 35 DOC-IWS-713A

24 7.2.5 OSD Miscellanies 24 of 35 DOC-IWS-713A

25 7.2.6 NTSC Video 25 of 35 DOC-IWS-713A

26 7.3 Touch screen Your FORMULA monitor may be configured with a resistive touch screen. The drivers can be found on the Drivers & Utilities CD that was delivered with the unit. More information on the Touch screen installation and calibration can be found in the Touch screen user guide. 7.4 Removing the Rear Cover To remove the rear cover: 1. Turn the unit so that the back panel faces you, then place the unit face down on a surface that won t scratch the display. 2. Loosen the captive thumbscrews on the back of the unit. 3. Lift the back cover up and off. 26 of 35 DOC-IWS-713A

27 Chapter 8: FORMULA Maintenance 8.1 Replacing the Backlights The life-time rating on LCD backlights are defined as the number of hours of operation until they are at half of their original brightness. The FORMULA Monitor backlights are rated at 40,000 hours this equates to approximately five years of continuous service. Signs that the backlights may need replacing include: 1. The top and/or the bottom of the screen are dim. 2. The brightness of the image on the screen flickers. 3. The video appears to be blank in normal light, but can be very faintly seen in strong external light. Replacing of the backlights: 1. Disconnect the cables from their connectors 2. At the cable end of each back light, remove a small portion of the foam strip to access the retaining screw. 3. Remove the retaining screw for each backlight 4. Remove the backlight by careful pulling them out. Backlight replacement kits are available from Nematron. Please contact Nematron for details. Rework instructions are included with the backlight replacement kit. 27 of 35 DOC-IWS-713A

28 Chapter 9: FORMULA Troubleshooting Symptom Possible Causes Actions The Unit doesn t power up. No Power connected Check Power connections Unit powers up but no display, the unit is not working upon arrival or after shipment. Other cause Heavy vibration or shock might have caused connectors coming out of their sockets. Other cause Call Nematron for assistance Open the unit and check all cable connections Call Nematron for Assistance Nematron Customer Service: Contact your local Nematron Sales Representative. For assistance in locating your Sales Representative, call (734) for North America or call +44 (0) for Europe, Middle East and Asia. Also, visit us on the Web at 28 of 35 DOC-IWS-713A

29 Appendix A: Model Configurator details Note: Configurations and Options are subject to change. For configurations not mentioned contact Nematron for support. (Configurator version ) I F = Industrial 9 = 0 2 = FORMULA 10 = 0 3 = Display Size 11 = 0 4 = M = Monitor 12 = 0 5 = Keyboard Options 13 = 0 6 = Touch screen 14 = 0 7 = - 15 = Options 8 = 0 IF IF INDUSTRIAL FORMULA 3 Display 5 15" TFT Display 7 17" TFT Display M Monitor (No slots) 5 Front Keyboard 0 No Front Keyboard 6 Touch Screen 1 No Touch Screen Controller 6 ELO Serial Touch Screen controller 7 Standard USB Touch Screen Controller 7-8,9,10,11,12,13, Options 0 F G H C P S N 19-8U Adapter Plate 19" - 8U Front Panel 19" - 8U Front Panel with Handles Extension Cable set Monitor 5 meter (16.4 ft) (USB and VGA only) Painted Steel Front Panel Without Nematron Logo Stainless Steel Front Panel with Nematron Logo Stainless Steel Front Panel without Nematron Logo 29 of 35 DOC-IWS-713A

30 Appendix B: FORMULA Monitor, 15inch Cutout, Weight, Power consumption and Dimensions,. Cutout Dimensions IF5M Nematron Formula Monitor 15-inch Display Cutout (Width x Height) 397mm (15.63 ) x 311mm (12.24 ) Weight IF5M Nematron Formula Monitor Weight 15-inch Display 7.7kg (17.0 Pounds) Power Consumption IF5M Nematron Formula Monitor Base Configuration IF5M 15-inch Display 23 Watts Unit Dimensions IF5M See next page- 30 of 35 DOC-IWS-713A

31 31 of 35 DOC-IWS-713A

32 Appendix D: FORMULA Monitor, 17inch Cutout, Weight, Power consumption and Dimensions Cutout Dimensions IF7M Nematron Formula Monitor 17-inch Display Cutout (Width x Height) 432mm (17.00 ) x 355mm (13.98 ) Weight IF7M Nematron Formula Monitor Weight 17-inch Display 10kg (22.0 Pounds) Power Consumption IF7M Nematron Formula Monitor Base Configuration IF7M 17-inch Display 28 Watts Unit Dimensions IF7M See next page- 32 of 35 DOC-IWS-713A

33 33 of 35 DOC-IWS-713A

34 Appendix E: Technical Data Do not use the FORMULA Monitor in areas of explosive hazard. General Info Protection Class Front Panel: IP65, when properly mounted in an enclosure. Enclosure: IP20 Operating Temp C Humidity Maximum 95%, non-condensing Power Supply Adapter Voltage Frequency Power Wide range VAC 47-63Hz 48 Watt TFT Display Size 15 Resolution 1024 x 768, XGA Pixel Pitch 0.297mm x 0.297mm Viewing Angle R/L 130 (typ), U/D 100 (typ) (CR>10) Colors 16M Luminance, white 250 cd/m² Backlight Life-time 40,000Hrs Size 17 Resolution 1280 x 1024, SXGA Pixel Pitch 0.264mm x 0.264mm Colors 16.2M Luminance, white 250 cd/m² Backlight Life-time 40,000Hrs Touch screen Touch screen Controller Transport and storage Approvals Resistive USB or Serial The same values for atmospheric humidity and shock resistance are to be observed during transport and storage as in operation. The shock resistance during transport can be improved by means of suitably packing the ipc. The ambient temperature during storage and transport must be between -20 C and +65 C. CE 34 of 35 DOC-IWS-713A

35 -Last Page- 35 of 35 DOC-IWS-713A