Cisco 7600 Series 2-Port OC-48c OC-48c/1-port OC-48c DPT OSM

Transcription

1 Data Sheet Cisco 7600 Series 2-Port OC-48c OC-48c/1-port OC-48c DPT OSM OC-48 distribution transport for service provider points of presence (POPs) and central offices with integrated IP services and Gigabit Ethernet Figure 1 Two-Port OC-48c POS/ One-Port OC-48c DPT Optical Services Module The anticipated dramatic growth of metropolitan-area networks (MANs) is forcing a reevaluation by service providers of the optimal use of their existing transport infrastructure. Synchronous Optical Network (SONET)/Synchronous Digital Hierarchy (SDH) technology will remain a pervasive transport technology because of its well-proven, low-delay restoration and resiliency capabilities. Nevertheless, there is a growing recognition that efficient transport of data traffic in the MAN will require a new class of transport distribution networks. The evolving transport technologies that will support these distribution networks must retain the outstanding resiliency and restoration capabilities of SONET, while delivering improved bandwidth multiplexing capabilities that can be delivered only by a packet-based transport. One of the most promising of these new transport technologies is Cisco Dynamic Packet Transport (DPT), which is based on the emerging resilient packet ring (RPR) IEEE standard. To meet these requirements, Cisco Systems offers a new Optical Services Module (OSM) for the Cisco 7600 Series Routers and Catalyst 6500 Series Switches that is configurable via software to be used either as a two-port OC-48c/STM-16 Packet-over-SONET (POS) module, or as a one-port OC-48c/STM-16 DPT module. The ability to configure this module for use in either POS networks or DPT networks provides the flexibility that service providers will need to adapt their distribution network to the rapidly increasing data traffic of their end customers. In addition, this module also provides four Gigabit Ethernet interfaces to provide additional data connectivity within the carrier s central office. This new Cisco 7600 Series Optical Service Module enables service providers to scale WAN bandwidth and performance to OC-48 speeds, while offering the flexibility to adapt to the distribution network architecture that will deliver the wide range of Layer 2 and Layer 3 services that their customers are demanding (refer to Figure 1). The Cisco 7600 is a high-performance router, which evolves from a specific set of Cisco Catalyst 6500 Series foundation elements combined with new optical-speed All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 1 of 10

2 WAN modules, and is specifically intended for service provider networks. The Cisco 7600 Series route-processing and forwarding capabilities support the ability to route using such core protocols as Border Gateway Protocol 4 (BGP4), Intermediate System-to-Intermediate System (IS-IS), and Open Shortest Path First (OSPF), while supporting quality of service (QoS) and packet filtering with optical transmission speed performance. Each Cisco 7600 Series chassis provides Network Equipment Building Standards (NEBS)-3 compliance and supports a 256-Gbps switch fabric, enabling high aggregate throughput. The Cisco 7600 Series can be configured with Optical Services Modules and any combination of traditional Cisco Catalyst 6000 Series interfaces, providing for outstanding scalability, with WAN interfaces from DS0 through OC-48/STM-16 and LAN interfaces from 10-Mbps Ethernet to Gigabit Ethernet, and on up to 10 Gigabit Ethernet. Transport Flexibility and Evolution Cisco DPT rings run over a variety of transport technologies, including SONET/SDH, wavelength-division multiplexing (WDM), and dark fiber. DPT provides service providers with the flexibility to operate packet rings over their embedded fiber transport infrastructure, as well as providing an evolution path to packet-optimized transport for high-bandwidth IP networks. An OC-48c/STM-16c DPT interface node consists of two OC-48c/STM-16c SONET/SDH interfaces, which have been configured to perform as a single DPT interface. Ring-Bandwidth Multiplication DPT uses optimal path selection, spatial reuse, statistical multiplexing, and two active connections to maximize the carrying capacity of the DPT ring. DPT also uses the Spatial Reuse Protocol (SRP) fairness algorithm to ensure that both global fairness and local bandwidth optimization are delivered on all segments of the DPT ring. Finally, DPT configurations are based on the concept of dual counter-rotating rings, which allow for efficient transmission of data and control information. Proactive Monitoring and Robust Self-Healing DPT combines powerful SONET/SDH overhead processing with Layer 2 management capabilities to deliver proactive, multilayer performance-monitoring, fault-detection, and fault-isolation capabilities. DPT provides sophisticated protection-switching capabilities for responsive self-healing via the Intelligent Protection Switching (IPS) algorithm. IPS enables sub-50-ms protection-switching performance for rapid service restoration and protection hierarchy to handle cases of multiple, concurrent degrade, failure, or maintenance events. All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 2 of 10

3 DPT Features and Benefits The features and benefits of DPT are described in Table 1. Table 1 DPT Features and Benefits Feature SRP fairness and spatial reuse IPS and single ring recovery Benefit Maximizes ring capacity, cost-effectiveness, and service stability via spatial reuse, statistical multiplexing, and distributed, inter-nodal fairness Maximizes ring robustness via self-healing around ring node or fiber failures and intelligent handling of multiple concurrent trouble events Provides fast IP service restoration without Layer 3 reconvergence to minimize impact on revenue-producing traffic Dual working fiber rings Topology discovery and routing procedures Network monitoring and management Pass-through mode support Transport flexibility Optics options Using interconnected line cards, dual working fiber rings maximize ring robustness and bandwidth capacity Minimize configuration requirements, optimize routing decisions for ring bandwidth maximization, and aid in network monitoring and management Maximize ring robustness and operational efficiency by providing SONET/SDH support, SRP Management Information Base (MIB) support, and Media Access Control (MAC)-layer counters for proactive monitoring and recovery and effective traffic-engineering capabilities Maximizes ring robustness and bandwidth availability by avoiding ring wraps caused by soft, recoverable failures in router hardware or software Maximizes deployment flexibility by operating via dedicated fiber, WDM wavelength, or as SONET/SDH tributary thus matching both embedded and evolving infrastructure Maximize application versatility and deployment flexibility by supporting single-mode short-, intermediate-, and long-reach optics DPT Ring Applications DPT rings enable a key set of applications for service providers and large enterprises, including: Robust, high-bandwidth intra-pop connectivity Regional POP interconnectivity Cable data access and distribution Metro packet transport for business and residential access services Regional backbone rings Distributed enterprise campus rings Feature Summary for Cisco 7600 OC-48 POS/DPT Module Software configurable selection of either OC-48 POS or DPT modes, thereby supporting transition between POS and DPT transport-distribution network architectures All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 3 of 10

4 High-performance application of QoS services (when configured for POS operation only), with support for 64 Differentiated Services Code Point (DSCP)-based queues per interface, where each queue is serviceable for IP-based traffic shaping and Class-Based Weighted Fair Queuing (CBWFQ) Compatibility with either the new Cisco 7600 Series or the Cisco Catalyst 6500 Series chassis (provided the Cisco Catalyst 6500 Series has been appropriately upgraded) Deep packet buffering to maximize TCP throughput, with advanced traffic management and prioritization schemes to ensure deterministic packet delivery Four additional Gigabit Ethernet ports, in addition to the OC-48 POS/DPT interface, thereby providing flexibility in WAN and LAN connectivity Ordering Information Ordering information for the Cisco 7600 Series One-Port OC-48c/STM-16 POS Optical Services Module is given in Table 2. Table 2 One-Port OC-48c/STM-16 POS Optical Services Module Ordering Information Part Number OSM-2OC48/1DPT-SS OSM-2OC48/1DPT-SS= OSM-2OC48/1DPT-SI OSM-2OC48/1DPT-SI= OSM-2OC48/1DPT-SL OSM-2OC48/1DPT-SL= MEM-OSM-128M MEM-OSM-256M Description OC-48c/STM-16 DPT OSM, SM-SR 1 with four Gigabit Ethernet OC-48c/STM-16 DPT OSM, SM-SR with four Gigabit Ethernet, spare OC-48c/STM-16 DPT OSM, SM-IR 2 with four Gigabit Ethernet OC-48c/STM-16 DPT OSM, SM-IR with four Gigabit Ethernet, spare OC-48c/STM-16 DPT OSM, SM-SL 3 with four Gigabit Ethernet OC-48c/STM-16 DPT OSM, SM-SL with four Gigabit Ethernet, spare 128-MB ECC 4 memory for OSMs 256-MB ECC memory for OSMs Note: = denotes spare (that is, OSM-2OC48/1DPT-SS= is the spare version when OSM is not ordered in a system). 1. Single mode, small reach 2. Single mode, intermediate reach 3. Single mode, long reach 4. Error Correcting Code All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 4 of 10

5 Technical Specifications OC-48c/STM-16 POS/DPT Specifications SONET/SDH Compliance Telcordia (Bellcore) GR-253-CORE (as applicable) ITU-T G.707, G.957, G.958 (as applicable) Support for 1+1 SONET automatic protection switching (APS) as per GR-253-CORE per port, per line card, per chassis (as applicable) Support for 1+1 SDH multiplex section protection (MSP) as per G.783 Annex A per port, per line card, per chassis (as applicable) Encapsulations Internet Engineering Task Force (IETF) RFC 1661, Point-to-Point Protocol (PPP) IETF RFC 1662, PPP in HDLC Like Framing IETF RFC 2615, PPP over SONET/SDH with 1+x 43 Self-Synchronous Payload Scrambling SONET/SDH Errors, Alarms, and Performance Monitoring Signal failure bit error rate (SF-ber) Signal degrade bit error rate (SD-ber) Signal label payload construction (C2) Path trace byte (J1) Section: Loss of signal (LOS) Loss of frame (LOF) Error counts for B1 Threshold crossing alarms (TCA) for B1 Line: Line alarm indication signal (LAIS) Line remote defect indication (LRDI) Line remote error indication (LREI) Error counts for B2 TCA for B2 Path: Path alarm indication signal (PAIS) Path remote defect indication (PRDI) Path remote error indication (PREI) Error Counts for B3 Path unequipped indication signal (PUNEQ) Path payload mismatch indication (PPLM) All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 5 of 10

6 TCA for B3 Loss of pointer (LOP) New pointer events (NEWPTR) Positive stuffing event (PSE) Negative stuffing event (NSE) SONET/SDH Synchronization Local (internal) timing (for inter-router connections over dark fiber or WDM equipment) Loop (line) timing (for connection to SONET/SDH equipment) +/ 20 ppm clock accuracy over full operating temperature Network Management Local loopback Network loopback NetFlow data export RFC 1595, Performance Statistics for Timed Intervals (current, 15-minute, multiple 15-minute, and 1-day intervals) Regenerator section Multiplex section Path errored seconds Severely errored seconds Severely errored framed seconds Connector LC connector Table 3 POS/DPT Optical Services Module Specifications Fiber interface Output Power Input Power Input Sensitivity Wavelength Min Max Max Min Min Max SM-SS dbm 3.0 dbm 0.0 dbm 18.0 dbm 1266 nm 1360 nm SM-SI dbm 0.0 dbm 0.0 dbm 18.0 dbm 1260 nm 1360 nm SM-SL dbm +3.0 dbm 9.0 dbm 28.0 dbm 1500 nm 1580 nm 1. Single mode, small reach 2. Single mode, intermediate reach 3. Single mode, long reach All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 6 of 10

7 Gigabit Ethernet Specifications IEEE 802.3z compliant Gigabit interface converter (GBIC)-based Gigabit Ethernet interfaces with SC connectors Table 4 Gigabit Ethernet Optical Specifications GBIC 1000BASE-LX: 50-_m multimode fiber 1000BASE-LX: 9/10-_m single-mode fiber 1000BASE-LH: 62.5-_m multimode fiber 1000BASE-LH: 50-_m multimode fiber 1000BASE-LH: 9/10-_m single-mode fiber 1000BASE-ZX: 9/10-_m single-mode fiber 1000BASE-ZX: dispersion-shifted fiber Distance Up to 550m Up to 5 km Up to 550m Up to 550m Up to 10 km Up to 70 km Up to 100 km Support for IEEE 802.1Q virtual LAN (VLAN) trunking with up to 4000 simultaneous VLANs Support for Hot Standby Router Protocol (HSRP) IEEE 802.3x support for autonegotiation flow control Support for jumbo frames with a maximum transmission unit (MTU) of 9192 bytes Cisco 7600 System Performance Features Hardware-based Cisco Express Forwarding at no less than 30 million Mpps Access control list (ACL) application, with as many as 15,000 ACL rules, at no less than 30 Mpps QoS classification at no less than 30 Mpps Policy routing at no less than 30 Mpps Support for 128,000 traffic accounting entries per system Support for online insertion and removal (OIR) Support for at least 220 ms of packet buffering per port Support for Simple Network Management Protocol (SNMP) I and II and four Remote Monitoring (RMON) groups per port: statistics, history, alarms, and events Physical Specifications Occupies one slot in any Cisco 7600 NEBS-certified chassis Occupies one slot in any Cisco Catalyst 6500 Series chassis (with appropriate upgrades) Two OC-48c/STM-16 ports supported per OSM Four Gigabit Ethernet optical ports per OSM Support for up to seven two-port OC-48c/STM-16 OSMs in a nine-slot Cisco 7600 Series chassis Required with either the Cisco 7600 Series or Cisco Catalyst 6500 Series chassis: All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 7 of 10

8 Supervisor Engine II: WS-X6K-S2-MSFC2 Recommended with either the Cisco 7600 Series or Cisco Catalyst 6500 Series chassis: Switch fabric module 256-Gbps crossbar fabric: WS-C6500-SFM Dimensions (H x W x D): 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm) Weight: 11.1 lb or 5.0 kg Mean time between failure (MTBF): seven years for system configuration Power consumption: 220W at 4.25 amps Indicators and Interfaces Status: green (operational)/red (faulty)/orange (module booting or running diagnostics) Link good: green (port active)/orange (disabled)/off (not active/connected)/blinking orange (failed diagnostic and disabled) Processors and Memory One 225-MHz R7000 MIPS RISC processor Configurable packet/route table memory options per line card: 64-MB ECC SDRAM 128-MB ECC SDRAM (default) 256-MB ECC SDRAM Parallel Express Forwarding (PXF) IP services processor(s) Provides up to 6 Mpps of distributed IP service application per PXF IP services processor Nonconfigurable PXF memory per line card: 128-MB ECC SDRAM of route table memory per PXF IP services processor 4-MB SSRAM of packet processing memory per PXF IP services processor MIB Support SONET MIB (RFC 1595) RFC 1157 SNMP RFC 1901 through 1907 SNMP v2c SNMP v3 MIB IF-MIB (RFC 1573) CISCO-STACK-MIB CISCO-CDP-MIB RMON MIB (RFC 1757) ENTITY-MIB (RFC 2037) HC-RMON RFC1213-MIB (MIB-II) SMON-MIB IP Statistics MIB All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 8 of 10

9 HSRP MIB Committed Access Rate (CAR) MIB Weighted Random Early Detection (WRED) MIB Resource Reservation Protocol (RSVP) MIB Cisco Round Trip Time Monitor (RTTMON) MIB Environmental Conditions Operating temperature: 32 to 104 F (0 to 40 C) Storage temperature: 4 to 149 F ( 20 to 65 C) Relative humidity: 5 to 90%, noncondensing Operating altitude: 500 to 6500 ft Regulatory Compliance Safety Compliance UL 1950 CAN/CSA C22.2 No EN Laser Safety (Class 1) 21CFR1040 Laser Safety EN60950 IEC TS 001 AS/NZS 3260 EMC Compliance FCC Part 15 (CFR 47) Class A VCCI Class A EN55022 Class A CISPR 22 Class A AS/NZS 3548 Class A EN55024 CE Marking NEBS Level 3 Compliance The Cisco 7600 chassis and Cisco Catalyst 6509 chassis have been certified as NEBS Level 3 compliant, according to the following specifications: GR-63-CORE - NEBS: Physical protection GR-1089-CORE - NEBS: EMC and safety All contents are Copyright All rights reserved. Important Notices and Privacy Statement. Page 9 of 10

10 ETSI Compliance ETS switching equipment Minimum Software Revision Cisco IOS Software Release 12.1(12)E For more information go to: For More Information on Cisco Products, Contact: United States and Canada: NETS (6387) Europe: Australia: Other: World Wide Web URL: Corporate Headquarters 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax: European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg CH Amsterdam The Netherlands www-europe.cisco.com Tel: Fax: Americas Headquarters 170 West Tasman Drive San Jose, CA USA Tel: Fax: Asia Pacific Headquarters Capital Tower 168 Robinson Road #22-01 to #29-01 Singapore Tel: Fax: Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Web site at Argentina Australia Austria Belgium Brazil Bulgaria Canada Chile China PRC Colombia Costa Rica Croatia Czech Republic Denmark Dubai, UAE Finland France Germany Greece Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea Luxembourg Malaysia Mexico The Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Scotland Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey Ukraine United Kingdom United States Venezuela Vietnam Zimbabwe All contents are Copyright All rights reserved. Catalyst, Cisco, Cisco IOS, Cisco Systems, and the Cisco Systems logo are registered trademarks of and/or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0304R) LS/LW